1// SPDX-License-Identifier: GPL-2.0 2#include <dt-bindings/iio/qcom,spmi-vadc.h> 3#include <dt-bindings/interrupt-controller/irq.h> 4#include <dt-bindings/spmi/spmi.h> 5 6 7/ { 8 thermal-zones { 9 pm8941-thermal { 10 polling-delay-passive = <100>; 11 polling-delay = <0>; 12 thermal-sensors = <&pm8941_temp>; 13 14 trips { 15 trip0 { 16 temperature = <105000>; 17 hysteresis = <2000>; 18 type = "passive"; 19 }; 20 21 trip1 { 22 temperature = <125000>; 23 hysteresis = <2000>; 24 type = "hot"; 25 }; 26 27 crit { 28 temperature = <145000>; 29 hysteresis = <2000>; 30 type = "critical"; 31 }; 32 }; 33 }; 34 }; 35}; 36 37&spmi_bus { 38 39 pm8941_0: pm8941@0 { 40 compatible = "qcom,pm8941", "qcom,spmi-pmic"; 41 reg = <0x0 SPMI_USID>; 42 #address-cells = <1>; 43 #size-cells = <0>; 44 45 rtc@6000 { 46 compatible = "qcom,pm8941-rtc"; 47 reg = <0x6000>, 48 <0x6100>; 49 reg-names = "rtc", "alarm"; 50 interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; 51 }; 52 53 pon@800 { 54 compatible = "qcom,pm8941-pon"; 55 reg = <0x800>; 56 57 pwrkey { 58 compatible = "qcom,pm8941-pwrkey"; 59 interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; 60 debounce = <15625>; 61 bias-pull-up; 62 }; 63 64 pm8941_resin: resin { 65 compatible = "qcom,pm8941-resin"; 66 interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; 67 debounce = <15625>; 68 bias-pull-up; 69 status = "disabled"; 70 }; 71 }; 72 73 usb_id: usb-detect@900 { 74 compatible = "qcom,pm8941-misc"; 75 reg = <0x900>; 76 interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>; 77 interrupt-names = "usb_id"; 78 }; 79 80 smbb: charger@1000 { 81 compatible = "qcom,pm8941-charger"; 82 reg = <0x1000>; 83 interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, 84 <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, 85 <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, 86 <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, 87 <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, 88 <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, 89 <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, 90 <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; 91 interrupt-names = "chg-done", 92 "chg-fast", 93 "chg-trkl", 94 "bat-temp-ok", 95 "bat-present", 96 "chg-gone", 97 "usb-valid", 98 "dc-valid"; 99 100 usb-otg-in-supply = <&pm8941_5vs1>; 101 102 status = "disabled"; 103 104 chg_otg: otg-vbus { }; 105 }; 106 107 pm8941_gpios: gpio@c000 { 108 compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio"; 109 reg = <0xc000>; 110 gpio-controller; 111 gpio-ranges = <&pm8941_gpios 0 0 36>; 112 #gpio-cells = <2>; 113 interrupt-controller; 114 #interrupt-cells = <2>; 115 116 boost_bypass_n_pin: boost-bypass-state { 117 pins = "gpio21"; 118 function = "normal"; 119 }; 120 }; 121 122 pm8941_mpps: mpps@a000 { 123 compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp"; 124 reg = <0xa000>; 125 gpio-controller; 126 #gpio-cells = <2>; 127 gpio-ranges = <&pm8941_mpps 0 0 8>; 128 interrupt-controller; 129 #interrupt-cells = <2>; 130 }; 131 132 pm8941_temp: temp-alarm@2400 { 133 compatible = "qcom,spmi-temp-alarm"; 134 reg = <0x2400>; 135 interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; 136 io-channels = <&pm8941_vadc VADC_DIE_TEMP>; 137 io-channel-names = "thermal"; 138 #thermal-sensor-cells = <0>; 139 }; 140 141 pm8941_vadc: adc@3100 { 142 compatible = "qcom,spmi-vadc"; 143 reg = <0x3100>; 144 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 145 #address-cells = <1>; 146 #size-cells = <0>; 147 #io-channel-cells = <1>; 148 149 150 channel@6 { 151 reg = <VADC_VBAT_SNS>; 152 }; 153 154 channel@8 { 155 reg = <VADC_DIE_TEMP>; 156 }; 157 158 channel@9 { 159 reg = <VADC_REF_625MV>; 160 }; 161 162 channel@a { 163 reg = <VADC_REF_1250MV>; 164 }; 165 166 channel@e { 167 reg = <VADC_GND_REF>; 168 }; 169 170 channel@f { 171 reg = <VADC_VDD_VADC>; 172 }; 173 174 channel@30 { 175 reg = <VADC_LR_MUX1_BAT_THERM>; 176 }; 177 }; 178 179 pm8941_iadc: adc@3600 { 180 compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc"; 181 reg = <0x3600>; 182 interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>; 183 qcom,external-resistor-micro-ohms = <10000>; 184 }; 185 186 pm8941_coincell: charger@2800 { 187 compatible = "qcom,pm8941-coincell"; 188 reg = <0x2800>; 189 status = "disabled"; 190 }; 191 }; 192 193 pm8941_1: pm8941@1 { 194 compatible = "qcom,pm8941", "qcom,spmi-pmic"; 195 reg = <0x1 SPMI_USID>; 196 #address-cells = <1>; 197 #size-cells = <0>; 198 199 pm8941_lpg: pwm { 200 compatible = "qcom,pm8941-lpg"; 201 202 #address-cells = <1>; 203 #size-cells = <0>; 204 #pwm-cells = <2>; 205 206 status = "disabled"; 207 }; 208 209 pm8941_vib: vibrator@c000 { 210 compatible = "qcom,pm8916-vib"; 211 reg = <0xc000>; 212 status = "disabled"; 213 }; 214 215 pm8941_wled: wled@d800 { 216 compatible = "qcom,pm8941-wled"; 217 reg = <0xd800>; 218 label = "backlight"; 219 220 status = "disabled"; 221 }; 222 223 regulators { 224 compatible = "qcom,pm8941-regulators"; 225 interrupts = <0x1 0x83 0x2 0>, <0x1 0x84 0x2 0>; 226 interrupt-names = "ocp-5vs1", "ocp-5vs2"; 227 vin_5vs-supply = <&pm8941_5v>; 228 229 pm8941_5v: s4 { 230 regulator-min-microvolt = <5000000>; 231 regulator-max-microvolt = <5000000>; 232 regulator-enable-ramp-delay = <500>; 233 }; 234 235 pm8941_5vs1: 5vs1 { 236 regulator-enable-ramp-delay = <1000>; 237 regulator-pull-down; 238 regulator-over-current-protection; 239 qcom,ocp-max-retries = <10>; 240 qcom,ocp-retry-delay = <30>; 241 qcom,vs-soft-start-strength = <0>; 242 regulator-initial-mode = <1>; 243 }; 244 245 pm8941_5vs2: 5vs2 { 246 regulator-enable-ramp-delay = <1000>; 247 regulator-pull-down; 248 regulator-over-current-protection; 249 qcom,ocp-max-retries = <10>; 250 qcom,ocp-retry-delay = <30>; 251 qcom,vs-soft-start-strength = <0>; 252 regulator-initial-mode = <1>; 253 }; 254 }; 255 }; 256}; 257