1// SPDX-License-Identifier: GPL-2.0 2/* 3 * at91-wb50n.dtsi - Device Tree include file for wb50n cpu module 4 * 5 * Copyright (C) 2018 Laird 6 * 7 */ 8 9#include "sama5d31.dtsi" 10 11/ { 12 model = "Laird Workgroup Bridge 50N - Atmel SAMA5D"; 13 compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5"; 14 15 chosen { 16 bootargs = "ubi.mtd=6 root=ubi0:rootfs rootfstype=ubifs rw"; 17 stdout-path = "serial0:115200n8"; 18 }; 19 20 memory@20000000 { 21 reg = <0x20000000 0x4000000>; 22 }; 23}; 24 25&pinctrl { 26 board { 27 pinctrl_mmc0_cd: mmc0_cd { 28 atmel,pins = <AT91_PIOC 26 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PC26 GPIO with pullup deglitch */ 29 }; 30 31 pinctrl_usba_vbus: usba_vbus { 32 atmel,pins = <AT91_PIOB 13 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB13 GPIO with deglitch */ 33 }; 34 }; 35}; 36 37&slow_xtal { 38 clock-frequency = <32768>; 39}; 40 41&main_xtal { 42 clock-frequency = <12000000>; 43}; 44 45&clk32k { 46 atmel,osc-bypass; 47}; 48 49&mmc0 { 50 pinctrl-names = "default"; 51 pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>; 52 cd-gpios = <&pioC 26 GPIO_ACTIVE_LOW>; 53 slot@0 { 54 reg = <0>; 55 bus-width = <4>; 56 }; 57}; 58 59&mmc1 { 60 pinctrl-names = "default"; 61 pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>; 62 status = "okay"; 63 atheros@0 { 64 compatible = "atheros,ath6kl"; 65 atheros,board-id = "SD32"; 66 reg = <0>; 67 bus-width = <4>; 68 }; 69}; 70 71&macb1 { 72 phy-mode = "rmii"; 73}; 74 75&dbgu { 76 dmas = <0>, <0>; /* Do not use DMA for dbgu */ 77}; 78 79/* On BB40 this port is labeled UART1 */ 80&usart0 { 81 atmel,use-dma-rx; 82 atmel,use-dma-tx; 83 pinctrl-names = "default"; 84 pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts_cts>; 85}; 86 87/* On BB40 this port is labeled UART0 */ 88&usart1 { 89 atmel,use-dma-rx; 90 atmel,use-dma-tx; 91 pinctrl-names = "default"; 92 pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>; 93 dtr-gpios = <&pioD 13 GPIO_ACTIVE_LOW>; 94 dsr-gpios = <&pioD 11 GPIO_ACTIVE_LOW>; 95 dcd-gpios = <&pioD 7 GPIO_ACTIVE_LOW>; 96 rng-gpios = <&pioD 8 GPIO_ACTIVE_LOW>; 97}; 98 99/* USART3 is direct-connect to the Bluetooth UART on the radio SIP */ 100&usart3 { 101 atmel,use-dma-rx; 102 atmel,use-dma-tx; 103 pinctrl-names = "default"; 104 pinctrl-0 = <&pinctrl_usart3 &pinctrl_usart3_rts_cts>; 105 status = "okay"; 106}; 107 108&spi1 { 109 cs-gpios = <&pioC 25 0>, <0>, <0>, <0>; 110}; 111 112&ebi { 113 pinctrl-0 = <&pinctrl_ebi_nand_addr>; 114 pinctrl-names = "default"; 115 status = "okay"; 116}; 117 118&nand_controller { 119 status = "okay"; 120 121 nand: nand@3 { 122 reg = <0x3 0x0 0x2>; 123 atmel,rb = <0>; 124 nand-bus-width = <8>; 125 nand-ecc-mode = "hw"; 126 nand-ecc-strength = <8>; 127 nand-ecc-step-size = <512>; 128 nand-on-flash-bbt; 129 label = "atmel_nand"; 130 131 partitions { 132 compatible = "fixed-partitions"; 133 #address-cells = <1>; 134 #size-cells = <1>; 135 136 at91bootstrap@0 { 137 label = "at91bs"; 138 reg = <0x0 0x20000>; 139 }; 140 141 uboot@20000 { 142 label = "u-boot"; 143 reg = <0x20000 0x80000>; 144 }; 145 146 ubootenv@a0000 { 147 label = "u-boot-env"; 148 reg = <0xa0000 0x20000>; 149 }; 150 151 ubootenv@c0000 { 152 label = "u-boot-env"; 153 reg = <0xc0000 0x20000>; 154 }; 155 156 kernel-a@e0000 { 157 label = "kernel-a"; 158 reg = <0xe0000 0x500000>; 159 }; 160 161 kernel-b@5e0000 { 162 label = "kernel-b"; 163 reg = <0x5e0000 0x500000>; 164 }; 165 166 rootfs-a@ae0000 { 167 label = "rootfs-a"; 168 reg = <0xae0000 0x3000000>; 169 }; 170 171 rootfs-b@3ae0000 { 172 label = "rootfs-b"; 173 reg = <0x3ae0000 0x3000000>; 174 }; 175 176 user@6ae0000 { 177 label = "user"; 178 reg = <0x6ae0000 0x14e0000>; 179 }; 180 }; 181 }; 182}; 183 184&usb0 { 185 atmel,vbus-gpio = <&pioB 13 GPIO_ACTIVE_LOW>; 186 pinctrl-names = "default"; 187 pinctrl-0 = <&pinctrl_usba_vbus>; 188}; 189 190&usb1 { 191 num-ports = <3>; 192 atmel,vbus-gpio = <&pioA 2 GPIO_ACTIVE_LOW>; 193 atmel,oc-gpio = <&pioA 4 GPIO_ACTIVE_LOW>; 194}; 195