1// SPDX-License-Identifier: GPL-2.0 2/ { 3 mbus@f1000000 { 4 pciec: pcie@82000000 { 5 compatible = "marvell,kirkwood-pcie"; 6 status = "disabled"; 7 device_type = "pci"; 8 9 #address-cells = <3>; 10 #size-cells = <2>; 11 12 bus-range = <0x00 0xff>; 13 14 ranges = 15 <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 16 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ 17 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>; 18 19 pcie0: pcie@1,0 { 20 device_type = "pci"; 21 assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>; 22 reg = <0x0800 0 0 0 0>; 23 #address-cells = <3>; 24 #size-cells = <2>; 25 #interrupt-cells = <1>; 26 ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 27 0x81000000 0 0 0x81000000 0x1 0 1 0>; 28 bus-range = <0x00 0xff>; 29 interrupt-names = "intx", "error"; 30 interrupts = <9>, <44>; 31 interrupt-map-mask = <0 0 0 7>; 32 interrupt-map = <0 0 0 1 &pcie_intc 0>, 33 <0 0 0 2 &pcie_intc 1>, 34 <0 0 0 3 &pcie_intc 2>, 35 <0 0 0 4 &pcie_intc 3>; 36 marvell,pcie-port = <0>; 37 marvell,pcie-lane = <0>; 38 clocks = <&gate_clk 2>; 39 status = "disabled"; 40 41 pcie_intc: interrupt-controller { 42 interrupt-controller; 43 #interrupt-cells = <1>; 44 }; 45 }; 46 }; 47 }; 48 49 ocp@f1000000 { 50 pinctrl: pin-controller@10000 { 51 compatible = "marvell,88f6192-pinctrl"; 52 53 pmx_sata0: pmx-sata0 { 54 marvell,pins = "mpp5", "mpp21", "mpp23"; 55 marvell,function = "sata0"; 56 }; 57 pmx_sata1: pmx-sata1 { 58 marvell,pins = "mpp4", "mpp20", "mpp22"; 59 marvell,function = "sata1"; 60 }; 61 pmx_sdio: pmx-sdio { 62 marvell,pins = "mpp12", "mpp13", "mpp14", 63 "mpp15", "mpp16", "mpp17"; 64 marvell,function = "sdio"; 65 }; 66 }; 67 68 rtc: rtc@10300 { 69 compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc"; 70 reg = <0x10300 0x20>; 71 interrupts = <53>; 72 clocks = <&gate_clk 7>; 73 }; 74 75 sata: sata@80000 { 76 compatible = "marvell,orion-sata"; 77 reg = <0x80000 0x5000>; 78 interrupts = <21>; 79 clocks = <&gate_clk 14>, <&gate_clk 15>; 80 clock-names = "0", "1"; 81 phys = <&sata_phy0>, <&sata_phy1>; 82 phy-names = "port0", "port1"; 83 status = "disabled"; 84 }; 85 86 sdio: mvsdio@90000 { 87 compatible = "marvell,orion-sdio"; 88 reg = <0x90000 0x200>; 89 interrupts = <28>; 90 clocks = <&gate_clk 4>; 91 bus-width = <4>; 92 cap-sdio-irq; 93 cap-sd-highspeed; 94 cap-mmc-highspeed; 95 status = "disabled"; 96 }; 97 }; 98}; 99