1==================================== 2Intelligent Keyboard (ikbd) Protocol 3==================================== 4 5 6Introduction 7============ 8 9The Atari Corp. Intelligent Keyboard (ikbd) is a general purpose keyboard 10controller that is flexible enough that it can be used in a variety of 11products without modification. The keyboard, with its microcontroller, 12provides a convenient connection point for a mouse and switch-type joysticks. 13The ikbd processor also maintains a time-of-day clock with one second 14resolution. 15The ikbd has been designed to be general enough that it can be used with a 16variety of new computer products. Product variations in a number of 17keyswitches, mouse resolution, etc. can be accommodated. 18The ikbd communicates with the main processor over a high speed bi-directional 19serial interface. It can function in a variety of modes to facilitate 20different applications of the keyboard, joysticks, or mouse. Limited use of 21the controller is possible in applications in which only a unidirectional 22communications medium is available by carefully designing the default modes. 23 24Keyboard 25======== 26 27The keyboard always returns key make/break scan codes. The ikbd generates 28keyboard scan codes for each key press and release. The key scan make (key 29closure) codes start at 1, and are defined in Appendix A. For example, the 30ISO key position in the scan code table should exist even if no keyswitch 31exists in that position on a particular keyboard. The break code for each key 32is obtained by ORing 0x80 with the make code. 33 34The special codes 0xF6 through 0xFF are reserved for use as follows: 35 36=================== ==================================================== 37 Code Command 38=================== ==================================================== 39 0xF6 status report 40 0xF7 absolute mouse position record 41 0xF8-0xFB relative mouse position records (lsbs determined by 42 mouse button states) 43 0xFC time-of-day 44 0xFD joystick report (both sticks) 45 0xFE joystick 0 event 46 0xFF joystick 1 event 47=================== ==================================================== 48 49The two shift keys return different scan codes in this mode. The ENTER key 50and the RETurn key are also distinct. 51 52Mouse 53===== 54 55The mouse port should be capable of supporting a mouse with resolution of 56approximately 200 counts (phase changes or 'clicks') per inch of travel. The 57mouse should be scanned at a rate that will permit accurate tracking at 58velocities up to 10 inches per second. 59The ikbd can report mouse motion in three distinctly different ways. It can 60report relative motion, absolute motion in a coordinate system maintained 61within the ikbd, or by converting mouse motion into keyboard cursor control 62key equivalents. 63The mouse buttons can be treated as part of the mouse or as additional 64keyboard keys. 65 66Relative Position Reporting 67--------------------------- 68 69In relative position mode, the ikbd will return relative mouse position 70records whenever a mouse event occurs. A mouse event consists of a mouse 71button being pressed or released, or motion in either axis exceeding a 72settable threshold of motion. Regardless of the threshold, all bits of 73resolution are returned to the host computer. 74Note that the ikbd may return mouse relative position reports with 75significantly more than the threshold delta x or y. This may happen since no 76relative mouse motion events will be generated: (a) while the keyboard has 77been 'paused' ( the event will be stored until keyboard communications is 78resumed) (b) while any event is being transmitted. 79 80The relative mouse position record is a three byte record of the form 81(regardless of keyboard mode):: 82 83 %111110xy ; mouse position record flag 84 ; where y is the right button state 85 ; and x is the left button state 86 X ; delta x as twos complement integer 87 Y ; delta y as twos complement integer 88 89Note that the value of the button state bits should be valid even if the 90MOUSE BUTTON ACTION has set the buttons to act like part of the keyboard. 91If the accumulated motion before the report packet is generated exceeds the 92+127...-128 range, the motion is broken into multiple packets. 93Note that the sign of the delta y reported is a function of the Y origin 94selected. 95 96Absolute Position reporting 97--------------------------- 98 99The ikbd can also maintain absolute mouse position. Commands exist for 100resetting the mouse position, setting X/Y scaling, and interrogating the 101current mouse position. 102 103Mouse Cursor Key Mode 104--------------------- 105 106The ikbd can translate mouse motion into the equivalent cursor keystrokes. 107The number of mouse clicks per keystroke is independently programmable in 108each axis. The ikbd internally maintains mouse motion information to the 109highest resolution available, and merely generates a pair of cursor key events 110for each multiple of the scale factor. 111Mouse motion produces the cursor key make code immediately followed by the 112break code for the appropriate cursor key. The mouse buttons produce scan 113codes above those normally assigned for the largest envisioned keyboard (i.e. 114LEFT=0x74 & RIGHT=0x75). 115 116Joystick 117======== 118 119Joystick Event Reporting 120------------------------ 121 122In this mode, the ikbd generates a record whenever the joystick position is 123changed (i.e. for each opening or closing of a joystick switch or trigger). 124 125The joystick event record is two bytes of the form:: 126 127 %1111111x ; Joystick event marker 128 ; where x is Joystick 0 or 1 129 %x000yyyy ; where yyyy is the stick position 130 ; and x is the trigger 131 132Joystick Interrogation 133---------------------- 134 135The current state of the joystick ports may be interrogated at any time in 136this mode by sending an 'Interrogate Joystick' command to the ikbd. 137 138The ikbd response to joystick interrogation is a three byte report of the form:: 139 140 0xFD ; joystick report header 141 %x000yyyy ; Joystick 0 142 %x000yyyy ; Joystick 1 143 ; where x is the trigger 144 ; and yyy is the stick position 145 146Joystick Monitoring 147------------------- 148 149A mode is available that devotes nearly all of the keyboard communications 150time to reporting the state of the joystick ports at a user specifiable rate. 151It remains in this mode until reset or commanded into another mode. The PAUSE 152command in this mode not only stop the output but also temporarily stops 153scanning the joysticks (samples are not queued). 154 155Fire Button Monitoring 156---------------------- 157 158A mode is provided to permit monitoring a single input bit at a high rate. In 159this mode the ikbd monitors the state of the Joystick 1 fire button at the 160maximum rate permitted by the serial communication channel. The data is packed 1618 bits per byte for transmission to the host. The ikbd remains in this mode 162until reset or commanded into another mode. The PAUSE command in this mode not 163only stops the output but also temporarily stops scanning the button (samples 164are not queued). 165 166Joystick Key Code Mode 167---------------------- 168 169The ikbd may be commanded to translate the use of either joystick into the 170equivalent cursor control keystroke(s). The ikbd provides a single breakpoint 171velocity joystick cursor. 172Joystick events produce the make code, immediately followed by the break code 173for the appropriate cursor motion keys. The trigger or fire buttons of the 174joysticks produce pseudo key scan codes above those used by the largest key 175matrix envisioned (i.e. JOYSTICK0=0x74, JOYSTICK1=0x75). 176 177Time-of-Day Clock 178================= 179 180The ikbd also maintains a time-of-day clock for the system. Commands are 181available to set and interrogate the timer-of-day clock. Time-keeping is 182maintained down to a resolution of one second. 183 184Status Inquiries 185================ 186 187The current state of ikbd modes and parameters may be found by sending status 188inquiry commands that correspond to the ikbd set commands. 189 190Power-Up Mode 191============= 192 193The keyboard controller will perform a simple self-test on power-up to detect 194major controller faults (ROM checksum and RAM test) and such things as stuck 195keys. Any keys down at power-up are presumed to be stuck, and their BREAK 196(sic) code is returned (which without the preceding MAKE code is a flag for a 197keyboard error). If the controller self-test completes without error, the code 1980xF0 is returned. (This code will be used to indicate the version/release of 199the ikbd controller. The first release of the ikbd is version 0xF0, should 200there be a second release it will be 0xF1, and so on.) 201The ikbd defaults to a mouse position reporting with threshold of 1 unit in 202either axis and the Y=0 origin at the top of the screen, and joystick event 203reporting mode for joystick 1, with both buttons being logically assigned to 204the mouse. After any joystick command, the ikbd assumes that joysticks are 205connected to both Joystick0 and Joystick1. Any mouse command (except MOUSE 206DISABLE) then causes port 0 to again be scanned as if it were a mouse, and 207both buttons are logically connected to it. If a mouse disable command is 208received while port 0 is presumed to be a mouse, the button is logically 209assigned to Joystick1 (until the mouse is reenabled by another mouse command). 210 211ikbd Command Set 212================ 213 214This section contains a list of commands that can be sent to the ikbd. Command 215codes (such as 0x00) which are not specified should perform no operation 216(NOPs). 217 218RESET 219----- 220 221:: 222 223 0x80 224 0x01 225 226N.B. The RESET command is the only two byte command understood by the ikbd. 227Any byte following an 0x80 command byte other than 0x01 is ignored (and causes 228the 0x80 to be ignored). 229A reset may also be caused by sending a break lasting at least 200mS to the 230ikbd. 231Executing the RESET command returns the keyboard to its default (power-up) 232mode and parameter settings. It does not affect the time-of-day clock. 233The RESET command or function causes the ikbd to perform a simple self-test. 234If the test is successful, the ikbd will send the code of 0xF0 within 300mS 235of receipt of the RESET command (or the end of the break, or power-up). The 236ikbd will then scan the key matrix for any stuck (closed) keys. Any keys found 237closed will cause the break scan code to be generated (the break code arriving 238without being preceded by the make code is a flag for a key matrix error). 239 240SET MOUSE BUTTON ACTION 241----------------------- 242 243:: 244 245 0x07 246 %00000mss ; mouse button action 247 ; (m is presumed = 1 when in MOUSE KEYCODE mode) 248 ; mss=0xy, mouse button press or release causes mouse 249 ; position report 250 ; where y=1, mouse key press causes absolute report 251 ; and x=1, mouse key release causes absolute report 252 ; mss=100, mouse buttons act like keys 253 254This command sets how the ikbd should treat the buttons on the mouse. The 255default mouse button action mode is %00000000, the buttons are treated as part 256of the mouse logically. 257When buttons act like keys, LEFT=0x74 & RIGHT=0x75. 258 259SET RELATIVE MOUSE POSITION REPORTING 260------------------------------------- 261 262:: 263 264 0x08 265 266Set relative mouse position reporting. (DEFAULT) Mouse position packets are 267generated asynchronously by the ikbd whenever motion exceeds the setable 268threshold in either axis (see SET MOUSE THRESHOLD). Depending upon the mouse 269key mode, mouse position reports may also be generated when either mouse 270button is pressed or released. Otherwise the mouse buttons behave as if they 271were keyboard keys. 272 273SET ABSOLUTE MOUSE POSITIONING 274------------------------------ 275 276:: 277 278 0x09 279 XMSB ; X maximum (in scaled mouse clicks) 280 XLSB 281 YMSB ; Y maximum (in scaled mouse clicks) 282 YLSB 283 284Set absolute mouse position maintenance. Resets the ikbd maintained X and Y 285coordinates. 286In this mode, the value of the internally maintained coordinates does NOT wrap 287between 0 and large positive numbers. Excess motion below 0 is ignored. The 288command sets the maximum positive value that can be attained in the scaled 289coordinate system. Motion beyond that value is also ignored. 290 291SET MOUSE KEYCODE MODE 292---------------------- 293 294:: 295 296 0x0A 297 deltax ; distance in X clicks to return (LEFT) or (RIGHT) 298 deltay ; distance in Y clicks to return (UP) or (DOWN) 299 300Set mouse monitoring routines to return cursor motion keycodes instead of 301either RELATIVE or ABSOLUTE motion records. The ikbd returns the appropriate 302cursor keycode after mouse travel exceeding the user specified deltas in 303either axis. When the keyboard is in key scan code mode, mouse motion will 304cause the make code immediately followed by the break code. Note that this 305command is not affected by the mouse motion origin. 306 307SET MOUSE THRESHOLD 308------------------- 309 310:: 311 312 0x0B 313 X ; x threshold in mouse ticks (positive integers) 314 Y ; y threshold in mouse ticks (positive integers) 315 316This command sets the threshold before a mouse event is generated. Note that 317it does NOT affect the resolution of the data returned to the host. This 318command is valid only in RELATIVE MOUSE POSITIONING mode. The thresholds 319default to 1 at RESET (or power-up). 320 321SET MOUSE SCALE 322--------------- 323 324:: 325 326 0x0C 327 X ; horizontal mouse ticks per internal X 328 Y ; vertical mouse ticks per internal Y 329 330This command sets the scale factor for the ABSOLUTE MOUSE POSITIONING mode. 331In this mode, the specified number of mouse phase changes ('clicks') must 332occur before the internally maintained coordinate is changed by one 333(independently scaled for each axis). Remember that the mouse position 334information is available only by interrogating the ikbd in the ABSOLUTE MOUSE 335POSITIONING mode unless the ikbd has been commanded to report on button press 336or release (see SET MOUSE BUTTON ACTION). 337 338INTERROGATE MOUSE POSITION 339-------------------------- 340 341:: 342 343 0x0D 344 Returns: 345 0xF7 ; absolute mouse position header 346 BUTTONS 347 0000dcba ; where a is right button down since last interrogation 348 ; b is right button up since last 349 ; c is left button down since last 350 ; d is left button up since last 351 XMSB ; X coordinate 352 XLSB 353 YMSB ; Y coordinate 354 YLSB 355 356The INTERROGATE MOUSE POSITION command is valid when in the ABSOLUTE MOUSE 357POSITIONING mode, regardless of the setting of the MOUSE BUTTON ACTION. 358 359LOAD MOUSE POSITION 360------------------- 361 362:: 363 364 0x0E 365 0x00 ; filler 366 XMSB ; X coordinate 367 XLSB ; (in scaled coordinate system) 368 YMSB ; Y coordinate 369 YLSB 370 371This command allows the user to preset the internally maintained absolute 372mouse position. 373 374SET Y=0 AT BOTTOM 375----------------- 376 377:: 378 379 0x0F 380 381This command makes the origin of the Y axis to be at the bottom of the 382logical coordinate system internal to the ikbd for all relative or absolute 383mouse motion. This causes mouse motion toward the user to be negative in sign 384and away from the user to be positive. 385 386SET Y=0 AT TOP 387-------------- 388 389:: 390 391 0x10 392 393Makes the origin of the Y axis to be at the top of the logical coordinate 394system within the ikbd for all relative or absolute mouse motion. (DEFAULT) 395This causes mouse motion toward the user to be positive in sign and away from 396the user to be negative. 397 398RESUME 399------ 400 401:: 402 403 0x11 404 405Resume sending data to the host. Since any command received by the ikbd after 406its output has been paused also causes an implicit RESUME this command can be 407thought of as a NO OPERATION command. If this command is received by the ikbd 408and it is not PAUSED, it is simply ignored. 409 410DISABLE MOUSE 411------------- 412 413:: 414 415 0x12 416 417All mouse event reporting is disabled (and scanning may be internally 418disabled). Any valid mouse mode command resumes mouse motion monitoring. (The 419valid mouse mode commands are SET RELATIVE MOUSE POSITION REPORTING, SET 420ABSOLUTE MOUSE POSITIONING, and SET MOUSE KEYCODE MODE. ) 421N.B. If the mouse buttons have been commanded to act like keyboard keys, this 422command DOES affect their actions. 423 424PAUSE OUTPUT 425------------ 426 427:: 428 429 0x13 430 431Stop sending data to the host until another valid command is received. Key 432matrix activity is still monitored and scan codes or ASCII characters enqueued 433(up to the maximum supported by the microcontroller) to be sent when the host 434allows the output to be resumed. If in the JOYSTICK EVENT REPORTING mode, 435joystick events are also queued. 436Mouse motion should be accumulated while the output is paused. If the ikbd is 437in RELATIVE MOUSE POSITIONING REPORTING mode, motion is accumulated beyond the 438normal threshold limits to produce the minimum number of packets necessary for 439transmission when output is resumed. Pressing or releasing either mouse button 440causes any accumulated motion to be immediately queued as packets, if the 441mouse is in RELATIVE MOUSE POSITION REPORTING mode. 442Because of the limitations of the microcontroller memory this command should 443be used sparingly, and the output should not be shut of for more than <tbd> 444milliseconds at a time. 445The output is stopped only at the end of the current 'even'. If the PAUSE 446OUTPUT command is received in the middle of a multiple byte report, the packet 447will still be transmitted to conclusion and then the PAUSE will take effect. 448When the ikbd is in either the JOYSTICK MONITORING mode or the FIRE BUTTON 449MONITORING mode, the PAUSE OUTPUT command also temporarily stops the 450monitoring process (i.e. the samples are not enqueued for transmission). 451 452SET JOYSTICK EVENT REPORTING 453---------------------------- 454 455:: 456 457 0x14 458 459Enter JOYSTICK EVENT REPORTING mode (DEFAULT). Each opening or closure of a 460joystick switch or trigger causes a joystick event record to be generated. 461 462SET JOYSTICK INTERROGATION MODE 463------------------------------- 464 465:: 466 467 0x15 468 469Disables JOYSTICK EVENT REPORTING. Host must send individual JOYSTICK 470INTERROGATE commands to sense joystick state. 471 472JOYSTICK INTERROGATE 473-------------------- 474 475:: 476 477 0x16 478 479Return a record indicating the current state of the joysticks. This command 480is valid in either the JOYSTICK EVENT REPORTING mode or the JOYSTICK 481INTERROGATION MODE. 482 483SET JOYSTICK MONITORING 484----------------------- 485 486:: 487 488 0x17 489 rate ; time between samples in hundredths of a second 490 Returns: (in packets of two as long as in mode) 491 %000000xy ; where y is JOYSTICK1 Fire button 492 ; and x is JOYSTICK0 Fire button 493 %nnnnmmmm ; where m is JOYSTICK1 state 494 ; and n is JOYSTICK0 state 495 496Sets the ikbd to do nothing but monitor the serial command line, maintain the 497time-of-day clock, and monitor the joystick. The rate sets the interval 498between joystick samples. 499N.B. The user should not set the rate higher than the serial communications 500channel will allow the 2 bytes packets to be transmitted. 501 502SET FIRE BUTTON MONITORING 503-------------------------- 504 505:: 506 507 0x18 508 Returns: (as long as in mode) 509 %bbbbbbbb ; state of the JOYSTICK1 fire button packed 510 ; 8 bits per byte, the first sample if the MSB 511 512Set the ikbd to do nothing but monitor the serial command line, maintain the 513time-of-day clock, and monitor the fire button on Joystick 1. The fire button 514is scanned at a rate that causes 8 samples to be made in the time it takes for 515the previous byte to be sent to the host (i.e. scan rate = 8/10 * baud rate). 516The sample interval should be as constant as possible. 517 518SET JOYSTICK KEYCODE MODE 519------------------------- 520 521:: 522 523 0x19 524 RX ; length of time (in tenths of seconds) until 525 ; horizontal velocity breakpoint is reached 526 RY ; length of time (in tenths of seconds) until 527 ; vertical velocity breakpoint is reached 528 TX ; length (in tenths of seconds) of joystick closure 529 ; until horizontal cursor key is generated before RX 530 ; has elapsed 531 TY ; length (in tenths of seconds) of joystick closure 532 ; until vertical cursor key is generated before RY 533 ; has elapsed 534 VX ; length (in tenths of seconds) of joystick closure 535 ; until horizontal cursor keystrokes are generated 536 ; after RX has elapsed 537 VY ; length (in tenths of seconds) of joystick closure 538 ; until vertical cursor keystrokes are generated 539 ; after RY has elapsed 540 541In this mode, joystick 0 is scanned in a way that simulates cursor keystrokes. 542On initial closure, a keystroke pair (make/break) is generated. Then up to Rn 543tenths of seconds later, keystroke pairs are generated every Tn tenths of 544seconds. After the Rn breakpoint is reached, keystroke pairs are generated 545every Vn tenths of seconds. This provides a velocity (auto-repeat) breakpoint 546feature. 547Note that by setting RX and/or Ry to zero, the velocity feature can be 548disabled. The values of TX and TY then become meaningless, and the generation 549of cursor 'keystrokes' is set by VX and VY. 550 551DISABLE JOYSTICKS 552----------------- 553 554:: 555 556 0x1A 557 558Disable the generation of any joystick events (and scanning may be internally 559disabled). Any valid joystick mode command resumes joystick monitoring. (The 560joystick mode commands are SET JOYSTICK EVENT REPORTING, SET JOYSTICK 561INTERROGATION MODE, SET JOYSTICK MONITORING, SET FIRE BUTTON MONITORING, and 562SET JOYSTICK KEYCODE MODE.) 563 564TIME-OF-DAY CLOCK SET 565--------------------- 566 567:: 568 569 0x1B 570 YY ; year (2 least significant digits) 571 MM ; month 572 DD ; day 573 hh ; hour 574 mm ; minute 575 ss ; second 576 577All time-of-day data should be sent to the ikbd in packed BCD format. 578Any digit that is not a valid BCD digit should be treated as a 'don't care' 579and not alter that particular field of the date or time. This permits setting 580only some subfields of the time-of-day clock. 581 582INTERROGATE TIME-OF-DAT CLOCK 583----------------------------- 584 585:: 586 587 0x1C 588 Returns: 589 0xFC ; time-of-day event header 590 YY ; year (2 least significant digits) 591 MM ; month 592 DD ; day 593 hh ; hour 594 mm ; minute 595 ss ; second 596 597 All time-of-day is sent in packed BCD format. 598 599MEMORY LOAD 600----------- 601 602:: 603 604 0x20 605 ADRMSB ; address in controller 606 ADRLSB ; memory to be loaded 607 NUM ; number of bytes (0-128) 608 { data } 609 610This command permits the host to load arbitrary values into the ikbd 611controller memory. The time between data bytes must be less than 20ms. 612 613MEMORY READ 614----------- 615 616:: 617 618 0x21 619 ADRMSB ; address in controller 620 ADRLSB ; memory to be read 621 Returns: 622 0xF6 ; status header 623 0x20 ; memory access 624 { data } ; 6 data bytes starting at ADR 625 626This command permits the host to read from the ikbd controller memory. 627 628CONTROLLER EXECUTE 629------------------ 630 631:: 632 633 0x22 634 ADRMSB ; address of subroutine in 635 ADRLSB ; controller memory to be called 636 637This command allows the host to command the execution of a subroutine in the 638ikbd controller memory. 639 640STATUS INQUIRIES 641---------------- 642 643:: 644 645 Status commands are formed by inclusively ORing 0x80 with the 646 relevant SET command. 647 648 Example: 649 0x88 (or 0x89 or 0x8A) ; request mouse mode 650 Returns: 651 0xF6 ; status response header 652 mode ; 0x08 is RELATIVE 653 ; 0x09 is ABSOLUTE 654 ; 0x0A is KEYCODE 655 param1 ; 0 is RELATIVE 656 ; XMSB maximum if ABSOLUTE 657 ; DELTA X is KEYCODE 658 param2 ; 0 is RELATIVE 659 ; YMSB maximum if ABSOLUTE 660 ; DELTA Y is KEYCODE 661 param3 ; 0 if RELATIVE 662 ; or KEYCODE 663 ; YMSB is ABSOLUTE 664 param4 ; 0 if RELATIVE 665 ; or KEYCODE 666 ; YLSB is ABSOLUTE 667 0 ; pad 668 0 669 670The STATUS INQUIRY commands request the ikbd to return either the current mode 671or the parameters associated with a given command. All status reports are 672padded to form 8 byte long return packets. The responses to the status 673requests are designed so that the host may store them away (after stripping 674off the status report header byte) and later send them back as commands to 675ikbd to restore its state. The 0 pad bytes will be treated as NOPs by the 676ikbd. 677 678 Valid STATUS INQUIRY commands are:: 679 680 0x87 mouse button action 681 0x88 mouse mode 682 0x89 683 0x8A 684 0x8B mnouse threshold 685 0x8C mouse scale 686 0x8F mouse vertical coordinates 687 0x90 ( returns 0x0F Y=0 at bottom 688 0x10 Y=0 at top ) 689 0x92 mouse enable/disable 690 ( returns 0x00 enabled) 691 0x12 disabled ) 692 0x94 joystick mode 693 0x95 694 0x96 695 0x9A joystick enable/disable 696 ( returns 0x00 enabled 697 0x1A disabled ) 698 699It is the (host) programmer's responsibility to have only one unanswered 700inquiry in process at a time. 701STATUS INQUIRY commands are not valid if the ikbd is in JOYSTICK MONITORING 702mode or FIRE BUTTON MONITORING mode. 703 704 705SCAN CODES 706========== 707 708The key scan codes returned by the ikbd are chosen to simplify the 709implementation of GSX. 710 711GSX Standard Keyboard Mapping 712 713======= ============ 714Hex Keytop 715======= ============ 71601 Esc 71702 1 71803 2 71904 3 72005 4 72106 5 72207 6 72308 7 72409 8 7250A 9 7260B 0 7270C \- 7280D \= 7290E BS 7300F TAB 73110 Q 73211 W 73312 E 73413 R 73514 T 73615 Y 73716 U 73817 I 73918 O 74019 P 7411A [ 7421B ] 7431C RET 7441D CTRL 7451E A 7461F S 74720 D 74821 F 74922 G 75023 H 75124 J 75225 K 75326 L 75427 ; 75528 ' 75629 \` 7572A (LEFT) SHIFT 7582B \\ 7592C Z 7602D X 7612E C 7622F V 76330 B 76431 N 76532 M 76633 , 76734 . 76835 / 76936 (RIGHT) SHIFT 77037 { NOT USED } 77138 ALT 77239 SPACE BAR 7733A CAPS LOCK 7743B F1 7753C F2 7763D F3 7773E F4 7783F F5 77940 F6 78041 F7 78142 F8 78243 F9 78344 F10 78445 { NOT USED } 78546 { NOT USED } 78647 HOME 78748 UP ARROW 78849 { NOT USED } 7894A KEYPAD - 7904B LEFT ARROW 7914C { NOT USED } 7924D RIGHT ARROW 7934E KEYPAD + 7944F { NOT USED } 79550 DOWN ARROW 79651 { NOT USED } 79752 INSERT 79853 DEL 79954 { NOT USED } 8005F { NOT USED } 80160 ISO KEY 80261 UNDO 80362 HELP 80463 KEYPAD ( 80564 KEYPAD / 80665 KEYPAD * 80766 KEYPAD * 80867 KEYPAD 7 80968 KEYPAD 8 81069 KEYPAD 9 8116A KEYPAD 4 8126B KEYPAD 5 8136C KEYPAD 6 8146D KEYPAD 1 8156E KEYPAD 2 8166F KEYPAD 3 81770 KEYPAD 0 81871 KEYPAD . 81972 KEYPAD ENTER 820======= ============ 821