1=============== 2uGuru datasheet 3=============== 4 5First of all, what I know about uGuru is no fact based on any help, hints or 6datasheet from Abit. The data I have got on uGuru have I assembled through 7my weak knowledge in "backwards engineering". 8And just for the record, you may have noticed uGuru isn't a chip developed by 9Abit, as they claim it to be. It's really just an microprocessor (uC) created by 10Winbond (W83L950D). And no, reading the manual for this specific uC or 11mailing Windbond for help won't give any useful data about uGuru, as it is 12the program inside the uC that is responding to calls. 13 14Olle Sandberg <ollebull@gmail.com>, 2005-05-25 15 16 17Original version by Olle Sandberg who did the heavy lifting of the initial 18reverse engineering. This version has been almost fully rewritten for clarity 19and extended with write support and info on more databanks, the write support 20is once again reverse engineered by Olle the additional databanks have been 21reverse engineered by me. I would like to express my thanks to Olle, this 22document and the Linux driver could not have been written without his efforts. 23 24Note: because of the lack of specs only the sensors part of the uGuru is 25described here and not the CPU / RAM / etc voltage & frequency control. 26 27Hans de Goede <j.w.r.degoede@hhs.nl>, 28-01-2006 28 29 30Detection 31========= 32 33As far as known the uGuru is always placed at and using the (ISA) I/O-ports 340xE0 and 0xE4, so we don't have to scan any port-range, just check what the two 35ports are holding for detection. We will refer to 0xE0 as CMD (command-port) 36and 0xE4 as DATA because Abit refers to them with these names. 37 38If DATA holds 0x00 or 0x08 and CMD holds 0x00 or 0xAC an uGuru could be 39present. We have to check for two different values at data-port, because 40after a reboot uGuru will hold 0x00 here, but if the driver is removed and 41later on attached again data-port will hold 0x08, more about this later. 42 43After wider testing of the Linux kernel driver some variants of the uGuru have 44turned up which will hold 0x00 instead of 0xAC at the CMD port, thus we also 45have to test CMD for two different values. On these uGuru's DATA will initially 46hold 0x09 and will only hold 0x08 after reading CMD first, so CMD must be read 47first! 48 49To be really sure an uGuru is present a test read of one or more register 50sets should be done. 51 52 53Reading / Writing 54================= 55 56Addressing 57---------- 58 59The uGuru has a number of different addressing levels. The first addressing 60level we will call banks. A bank holds data for one or more sensors. The data 61in a bank for a sensor is one or more bytes large. 62 63The number of bytes is fixed for a given bank, you should always read or write 64that many bytes, reading / writing more will fail, the results when writing 65less then the number of bytes for a given bank are undetermined. 66 67See below for all known bank addresses, numbers of sensors in that bank, 68number of bytes data per sensor and contents/meaning of those bytes. 69 70Although both this document and the kernel driver have kept the sensor 71terminoligy for the addressing within a bank this is not 100% correct, in 72bank 0x24 for example the addressing within the bank selects a PWM output not 73a sensor. 74 75Notice that some banks have both a read and a write address this is how the 76uGuru determines if a read from or a write to the bank is taking place, thus 77when reading you should always use the read address and when writing the 78write address. The write address is always one (1) more than the read address. 79 80 81uGuru ready 82----------- 83 84Before you can read from or write to the uGuru you must first put the uGuru 85in "ready" mode. 86 87To put the uGuru in ready mode first write 0x00 to DATA and then wait for DATA 88to hold 0x09, DATA should read 0x09 within 250 read cycles. 89 90Next CMD _must_ be read and should hold 0xAC, usually CMD will hold 0xAC the 91first read but sometimes it takes a while before CMD holds 0xAC and thus it 92has to be read a number of times (max 50). 93 94After reading CMD, DATA should hold 0x08 which means that the uGuru is ready 95for input. As above DATA will usually hold 0x08 the first read but not always. 96This step can be skipped, but it is undetermined what happens if the uGuru has 97not yet reported 0x08 at DATA and you proceed with writing a bank address. 98 99 100Sending bank and sensor addresses to the uGuru 101---------------------------------------------- 102 103First the uGuru must be in "ready" mode as described above, DATA should hold 1040x08 indicating that the uGuru wants input, in this case the bank address. 105 106Next write the bank address to DATA. After the bank address has been written 107wait for to DATA to hold 0x08 again indicating that it wants / is ready for 108more input (max 250 reads). 109 110Once DATA holds 0x08 again write the sensor address to CMD. 111 112 113Reading 114------- 115 116First send the bank and sensor addresses as described above. 117Then for each byte of data you want to read wait for DATA to hold 0x01 118which indicates that the uGuru is ready to be read (max 250 reads) and once 119DATA holds 0x01 read the byte from CMD. 120 121Once all bytes have been read data will hold 0x09, but there is no reason to 122test for this. Notice that the number of bytes is bank address dependent see 123above and below. 124 125After completing a successful read it is advised to put the uGuru back in 126ready mode, so that it is ready for the next read / write cycle. This way 127if your program / driver is unloaded and later loaded again the detection 128algorithm described above will still work. 129 130 131 132Writing 133------- 134 135First send the bank and sensor addresses as described above. 136Then for each byte of data you want to write wait for DATA to hold 0x00 137which indicates that the uGuru is ready to be written (max 250 reads) and 138once DATA holds 0x00 write the byte to CMD. 139 140Once all bytes have been written wait for DATA to hold 0x01 (max 250 reads) 141don't ask why this is the way it is. 142 143Once DATA holds 0x01 read CMD it should hold 0xAC now. 144 145After completing a successful write it is advised to put the uGuru back in 146ready mode, so that it is ready for the next read / write cycle. This way 147if your program / driver is unloaded and later loaded again the detection 148algorithm described above will still work. 149 150 151Gotchas 152------- 153 154After wider testing of the Linux kernel driver some variants of the uGuru have 155turned up which do not hold 0x08 at DATA within 250 reads after writing the 156bank address. With these versions this happens quite frequent, using larger 157timeouts doesn't help, they just go offline for a second or 2, doing some 158internal callibration or whatever. Your code should be prepared to handle 159this and in case of no response in this specific case just goto sleep for a 160while and then retry. 161 162 163Address Map 164=========== 165 166Bank 0x20 Alarms (R) 167-------------------- 168This bank contains 0 sensors, iow the sensor address is ignored (but must be 169written) just use 0. Bank 0x20 contains 3 bytes: 170 171Byte 0: 172 This byte holds the alarm flags for sensor 0-7 of Sensor Bank1, with bit 0 173 corresponding to sensor 0, 1 to 1, etc. 174 175Byte 1: 176 This byte holds the alarm flags for sensor 8-15 of Sensor Bank1, with bit 0 177 corresponding to sensor 8, 1 to 9, etc. 178 179Byte 2: 180 This byte holds the alarm flags for sensor 0-5 of Sensor Bank2, with bit 0 181 corresponding to sensor 0, 1 to 1, etc. 182 183 184Bank 0x21 Sensor Bank1 Values / Readings (R) 185-------------------------------------------- 186This bank contains 16 sensors, for each sensor it contains 1 byte. 187So far the following sensors are known to be available on all motherboards: 188 189- Sensor 0 CPU temp 190- Sensor 1 SYS temp 191- Sensor 3 CPU core volt 192- Sensor 4 DDR volt 193- Sensor 10 DDR Vtt volt 194- Sensor 15 PWM temp 195 196Byte 0: 197 This byte holds the reading from the sensor. Sensors in Bank1 can be both 198 volt and temp sensors, this is motherboard specific. The uGuru however does 199 seem to know (be programmed with) what kindoff sensor is attached see Sensor 200 Bank1 Settings description. 201 202Volt sensors use a linear scale, a reading 0 corresponds with 0 volt and a 203reading of 255 with 3494 mV. The sensors for higher voltages however are 204connected through a division circuit. The currently known division circuits 205in use result in ranges of: 0-4361mV, 0-6248mV or 0-14510mV. 3.3 volt sources 206use the 0-4361mV range, 5 volt the 0-6248mV and 12 volt the 0-14510mV . 207 208Temp sensors also use a linear scale, a reading of 0 corresponds with 0 degree 209Celsius and a reading of 255 with a reading of 255 degrees Celsius. 210 211 212Bank 0x22 Sensor Bank1 Settings (R) and Bank 0x23 Sensor Bank1 Settings (W) 213--------------------------------------------------------------------------- 214 215Those banks contain 16 sensors, for each sensor it contains 3 bytes. Each 216set of 3 bytes contains the settings for the sensor with the same sensor 217address in Bank 0x21 . 218 219Byte 0: 220 Alarm behaviour for the selected sensor. A 1 enables the described 221 behaviour. 222 223Bit 0: 224 Give an alarm if measured temp is over the warning threshold (RW) [1]_ 225 226Bit 1: 227 Give an alarm if measured volt is over the max threshold (RW) [2]_ 228 229Bit 2: 230 Give an alarm if measured volt is under the min threshold (RW) [2]_ 231 232Bit 3: 233 Beep if alarm (RW) 234 235Bit 4: 236 1 if alarm cause measured temp is over the warning threshold (R) 237 238Bit 5: 239 1 if alarm cause measured volt is over the max threshold (R) 240 241Bit 6: 242 1 if alarm cause measured volt is under the min threshold (R) 243 244Bit 7: 245 - Volt sensor: Shutdown if alarm persist for more than 4 seconds (RW) 246 - Temp sensor: Shutdown if temp is over the shutdown threshold (RW) 247 248.. [1] This bit is only honored/used by the uGuru if a temp sensor is connected 249 250.. [2] This bit is only honored/used by the uGuru if a volt sensor is connected 251 Note with some trickery this can be used to find out what kinda sensor 252 is detected see the Linux kernel driver for an example with many 253 comments on how todo this. 254 255Byte 1: 256 - Temp sensor: warning threshold (scale as bank 0x21) 257 - Volt sensor: min threshold (scale as bank 0x21) 258 259Byte 2: 260 - Temp sensor: shutdown threshold (scale as bank 0x21) 261 - Volt sensor: max threshold (scale as bank 0x21) 262 263 264Bank 0x24 PWM outputs for FAN's (R) and Bank 0x25 PWM outputs for FAN's (W) 265--------------------------------------------------------------------------- 266 267Those banks contain 3 "sensors", for each sensor it contains 5 bytes. 268 - Sensor 0 usually controls the CPU fan 269 - Sensor 1 usually controls the NB (or chipset for single chip) fan 270 - Sensor 2 usually controls the System fan 271 272Byte 0: 273 Flag 0x80 to enable control, Fan runs at 100% when disabled. 274 low nibble (temp)sensor address at bank 0x21 used for control. 275 276Byte 1: 277 0-255 = 0-12v (linear), specify voltage at which fan will rotate when under 278 low threshold temp (specified in byte 3) 279 280Byte 2: 281 0-255 = 0-12v (linear), specify voltage at which fan will rotate when above 282 high threshold temp (specified in byte 4) 283 284Byte 3: 285 Low threshold temp (scale as bank 0x21) 286 287byte 4: 288 High threshold temp (scale as bank 0x21) 289 290 291Bank 0x26 Sensors Bank2 Values / Readings (R) 292--------------------------------------------- 293 294This bank contains 6 sensors (AFAIK), for each sensor it contains 1 byte. 295 296So far the following sensors are known to be available on all motherboards: 297 - Sensor 0: CPU fan speed 298 - Sensor 1: NB (or chipset for single chip) fan speed 299 - Sensor 2: SYS fan speed 300 301Byte 0: 302 This byte holds the reading from the sensor. 0-255 = 0-15300 (linear) 303 304 305Bank 0x27 Sensors Bank2 Settings (R) and Bank 0x28 Sensors Bank2 Settings (W) 306----------------------------------------------------------------------------- 307 308Those banks contain 6 sensors (AFAIK), for each sensor it contains 2 bytes. 309 310Byte 0: 311 Alarm behaviour for the selected sensor. A 1 enables the described behaviour. 312 313Bit 0: 314 Give an alarm if measured rpm is under the min threshold (RW) 315 316Bit 3: 317 Beep if alarm (RW) 318 319Bit 7: 320 Shutdown if alarm persist for more than 4 seconds (RW) 321 322Byte 1: 323 min threshold (scale as bank 0x26) 324 325 326Warning for the adventurous 327=========================== 328 329A word of caution to those who want to experiment and see if they can figure 330the voltage / clock programming out, I tried reading and only reading banks 3310-0x30 with the reading code used for the sensor banks (0x20-0x28) and this 332resulted in a _permanent_ reprogramming of the voltages, luckily I had the 333sensors part configured so that it would shutdown my system on any out of spec 334voltages which proprably safed my computer (after a reboot I managed to 335immediately enter the bios and reload the defaults). This probably means that 336the read/write cycle for the non sensor part is different from the sensor part. 337