1.. Copyright 2001 Matthew Wilcox 2.. 3.. This documentation is free software; you can redistribute 4.. it and/or modify it under the terms of the GNU General Public 5.. License as published by the Free Software Foundation; either 6.. version 2 of the License, or (at your option) any later 7.. version. 8 9=============================== 10Bus-Independent Device Accesses 11=============================== 12 13:Author: Matthew Wilcox 14:Author: Alan Cox 15 16Introduction 17============ 18 19Linux provides an API which abstracts performing IO across all busses 20and devices, allowing device drivers to be written independently of bus 21type. 22 23Memory Mapped IO 24================ 25 26Getting Access to the Device 27---------------------------- 28 29The most widely supported form of IO is memory mapped IO. That is, a 30part of the CPU's address space is interpreted not as accesses to 31memory, but as accesses to a device. Some architectures define devices 32to be at a fixed address, but most have some method of discovering 33devices. The PCI bus walk is a good example of such a scheme. This 34document does not cover how to receive such an address, but assumes you 35are starting with one. Physical addresses are of type unsigned long. 36 37This address should not be used directly. Instead, to get an address 38suitable for passing to the accessor functions described below, you 39should call ioremap(). An address suitable for accessing 40the device will be returned to you. 41 42After you've finished using the device (say, in your module's exit 43routine), call iounmap() in order to return the address 44space to the kernel. Most architectures allocate new address space each 45time you call ioremap(), and they can run out unless you 46call iounmap(). 47 48Accessing the device 49-------------------- 50 51The part of the interface most used by drivers is reading and writing 52memory-mapped registers on the device. Linux provides interfaces to read 53and write 8-bit, 16-bit, 32-bit and 64-bit quantities. Due to a 54historical accident, these are named byte, word, long and quad accesses. 55Both read and write accesses are supported; there is no prefetch support 56at this time. 57 58The functions are named readb(), readw(), readl(), readq(), 59readb_relaxed(), readw_relaxed(), readl_relaxed(), readq_relaxed(), 60writeb(), writew(), writel() and writeq(). 61 62Some devices (such as framebuffers) would like to use larger transfers than 638 bytes at a time. For these devices, the memcpy_toio(), 64memcpy_fromio() and memset_io() functions are 65provided. Do not use memset or memcpy on IO addresses; they are not 66guaranteed to copy data in order. 67 68The read and write functions are defined to be ordered. That is the 69compiler is not permitted to reorder the I/O sequence. When the ordering 70can be compiler optimised, you can use __readb() and friends to 71indicate the relaxed ordering. Use this with care. 72 73While the basic functions are defined to be synchronous with respect to 74each other and ordered with respect to each other the busses the devices 75sit on may themselves have asynchronicity. In particular many authors 76are burned by the fact that PCI bus writes are posted asynchronously. A 77driver author must issue a read from the same device to ensure that 78writes have occurred in the specific cases the author cares. This kind 79of property cannot be hidden from driver writers in the API. In some 80cases, the read used to flush the device may be expected to fail (if the 81card is resetting, for example). In that case, the read should be done 82from config space, which is guaranteed to soft-fail if the card doesn't 83respond. 84 85The following is an example of flushing a write to a device when the 86driver would like to ensure the write's effects are visible prior to 87continuing execution:: 88 89 static inline void 90 qla1280_disable_intrs(struct scsi_qla_host *ha) 91 { 92 struct device_reg *reg; 93 94 reg = ha->iobase; 95 /* disable risc and host interrupts */ 96 WRT_REG_WORD(®->ictrl, 0); 97 /* 98 * The following read will ensure that the above write 99 * has been received by the device before we return from this 100 * function. 101 */ 102 RD_REG_WORD(®->ictrl); 103 ha->flags.ints_enabled = 0; 104 } 105 106PCI ordering rules also guarantee that PIO read responses arrive after any 107outstanding DMA writes from that bus, since for some devices the result of 108a readb() call may signal to the driver that a DMA transaction is 109complete. In many cases, however, the driver may want to indicate that the 110next readb() call has no relation to any previous DMA writes 111performed by the device. The driver can use readb_relaxed() for 112these cases, although only some platforms will honor the relaxed 113semantics. Using the relaxed read functions will provide significant 114performance benefits on platforms that support it. The qla2xxx driver 115provides examples of how to use readX_relaxed(). In many cases, a majority 116of the driver's readX() calls can safely be converted to readX_relaxed() 117calls, since only a few will indicate or depend on DMA completion. 118 119Port Space Accesses 120=================== 121 122Port Space Explained 123-------------------- 124 125Another form of IO commonly supported is Port Space. This is a range of 126addresses separate to the normal memory address space. Access to these 127addresses is generally not as fast as accesses to the memory mapped 128addresses, and it also has a potentially smaller address space. 129 130Unlike memory mapped IO, no preparation is required to access port 131space. 132 133Accessing Port Space 134-------------------- 135 136Accesses to this space are provided through a set of functions which 137allow 8-bit, 16-bit and 32-bit accesses; also known as byte, word and 138long. These functions are inb(), inw(), 139inl(), outb(), outw() and 140outl(). 141 142Some variants are provided for these functions. Some devices require 143that accesses to their ports are slowed down. This functionality is 144provided by appending a ``_p`` to the end of the function. 145There are also equivalents to memcpy. The ins() and 146outs() functions copy bytes, words or longs to the given 147port. 148 149Public Functions Provided 150========================= 151 152.. kernel-doc:: arch/x86/include/asm/io.h 153 :internal: 154 155.. kernel-doc:: lib/pci_iomap.c 156 :export: 157