1OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS 2 3OMAP MUSB GLUE 4 - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb" 5 - ti,hwmods : must be "usb_otg_hs" 6 - multipoint : Should be "1" indicating the musb controller supports 7 multipoint. This is a MUSB configuration-specific setting. 8 - num-eps : Specifies the number of endpoints. This is also a 9 MUSB configuration-specific setting. Should be set to "16" 10 - ram-bits : Specifies the ram address size. Should be set to "12" 11 - interface-type : This is a board specific setting to describe the type of 12 interface between the controller and the phy. It should be "0" or "1" 13 specifying ULPI and UTMI respectively. 14 - mode : Should be "3" to represent OTG. "1" signifies HOST and "2" 15 represents PERIPHERAL. 16 - power : Should be "50". This signifies the controller can supply up to 17 100mA when operating in host mode. 18 - usb-phy : the phandle for the PHY device 19 - phys : the phandle for the PHY device (used by generic PHY framework) 20 - phy-names : the names of the PHY corresponding to the PHYs present in the 21 *phy* phandle. 22 23Optional properties: 24 - ctrl-module : phandle of the control module this glue uses to write to 25 mailbox 26 27SOC specific device node entry 28usb_otg_hs: usb_otg_hs@4a0ab000 { 29 compatible = "ti,omap4-musb"; 30 ti,hwmods = "usb_otg_hs"; 31 multipoint = <1>; 32 num-eps = <16>; 33 ram-bits = <12>; 34 ctrl-module = <&omap_control_usb>; 35 phys = <&usb2_phy>; 36 phy-names = "usb2-phy"; 37}; 38 39Board specific device node entry 40&usb_otg_hs { 41 interface-type = <1>; 42 mode = <3>; 43 power = <50>; 44}; 45 46OMAP DWC3 GLUE 47 - compatible : Should be 48 * "ti,dwc3" for OMAP5 and DRA7 49 * "ti,am437x-dwc3" for AM437x 50 - ti,hwmods : Should be "usb_otg_ss" 51 - reg : Address and length of the register set for the device. 52 - interrupts : The irq number of this device that is used to interrupt the 53 MPU 54 - #address-cells, #size-cells : Must be present if the device has sub-nodes 55 - utmi-mode : controls the source of UTMI/PIPE status for VBUS and OTG ID. 56 It should be set to "1" for HW mode and "2" for SW mode. 57 - ranges: the child address space are mapped 1:1 onto the parent address space 58 59Optional Properties: 60 - extcon : phandle for the extcon device omap dwc3 uses to detect 61 connect/disconnect events. 62 - vbus-supply : phandle to the regulator device tree node if needed. 63 64Sub-nodes: 65The dwc3 core should be added as subnode to omap dwc3 glue. 66- dwc3 : 67 The binding details of dwc3 can be found in: 68 Documentation/devicetree/bindings/usb/dwc3.txt 69 70omap_dwc3 { 71 compatible = "ti,dwc3"; 72 ti,hwmods = "usb_otg_ss"; 73 reg = <0x4a020000 0x1ff>; 74 interrupts = <0 93 4>; 75 #address-cells = <1>; 76 #size-cells = <1>; 77 utmi-mode = <2>; 78 ranges; 79}; 80 81