xref: /linux/Documentation/devicetree/bindings/ufs/ufs-common.yaml (revision 24168c5e6dfbdd5b414f048f47f75d64533296ca) 
1# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/ufs/ufs-common.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Common properties for Universal Flash Storage (UFS) Host Controllers
8
9maintainers:
10  - Alim Akhtar <alim.akhtar@samsung.com>
11  - Avri Altman <avri.altman@wdc.com>
12
13properties:
14  clocks: true
15
16  clock-names: true
17
18  freq-table-hz:
19    items:
20      items:
21        - description: Minimum frequency for given clock in Hz
22        - description: Maximum frequency for given clock in Hz
23    deprecated: true
24    description: |
25      Preferred is operating-points-v2.
26
27      Array of <min max> operating frequencies in Hz stored in the same order
28      as the clocks property. If either this property or operating-points-v2 is
29      not defined or a value in the array is "0" then it is assumed that the
30      frequency is set by the parent clock or a fixed rate clock source.
31
32  operating-points-v2:
33    description:
34      Preferred over freq-table-hz.
35      If present, each OPP must contain array of frequencies stored in the same
36      order for each clock.  If clock frequency in the array is "0" then it is
37      assumed that the frequency is set by the parent clock or a fixed rate
38      clock source.
39
40  opp-table:
41    type: object
42
43  interrupts:
44    maxItems: 1
45
46  lanes-per-direction:
47    $ref: /schemas/types.yaml#/definitions/uint32
48    enum: [1, 2]
49    default: 2
50    description:
51      Number of lanes available per direction.  Note that it is assume same
52      number of lanes is used both directions at once.
53
54  vdd-hba-supply:
55    description:
56      Phandle to UFS host controller supply regulator node.
57
58  vcc-supply:
59    description:
60      Phandle to VCC supply regulator node.
61
62  vccq-supply:
63    description:
64      Phandle to VCCQ supply regulator node.
65
66  vccq2-supply:
67    description:
68      Phandle to VCCQ2 supply regulator node.
69
70  vcc-supply-1p8:
71    type: boolean
72    description:
73      For embedded UFS devices, valid VCC range is 1.7-1.95V or 2.7-3.6V. This
74      boolean property when set, specifies to use low voltage range of
75      1.7-1.95V. Note for external UFS cards this property is invalid and valid
76      VCC range is always 2.7-3.6V.
77
78  vcc-max-microamp:
79    description:
80      Specifies max. load that can be drawn from VCC supply.
81
82  vccq-max-microamp:
83    description:
84      Specifies max. load that can be drawn from VCCQ supply.
85
86  vccq2-max-microamp:
87    description:
88      Specifies max. load that can be drawn from VCCQ2 supply.
89
90  msi-parent: true
91
92dependencies:
93  freq-table-hz: [ clocks ]
94  operating-points-v2: [ clocks, clock-names ]
95
96required:
97  - interrupts
98
99allOf:
100  - if:
101      required:
102        - freq-table-hz
103    then:
104      properties:
105        operating-points-v2: false
106  - if:
107      required:
108        - operating-points-v2
109    then:
110      properties:
111        freq-table-hz: false
112
113additionalProperties: true
114