1Renesas R-Car sound 2 3============================================= 4* Modules 5============================================= 6 7Renesas R-Car and RZ/G sound is constructed from below modules 8(for Gen2 or later) 9 10 SCU : Sampling Rate Converter Unit 11 - SRC : Sampling Rate Converter 12 - CMD 13 - CTU : Channel Transfer Unit 14 - MIX : Mixer 15 - DVC : Digital Volume and Mute Function 16 SSIU : Serial Sound Interface Unit 17 SSI : Serial Sound Interface 18 19See detail of each module's channels, connection, limitation on datasheet 20 21============================================= 22* Multi channel 23============================================= 24 25Multi channel is supported by Multi-SSI, or TDM-SSI. 26 27 Multi-SSI : 6ch case, you can use stereo x 3 SSI 28 TDM-SSI : 6ch case, you can use TDM 29 30============================================= 31* Enable/Disable each modules 32============================================= 33 34See datasheet to check SRC/CTU/MIX/DVC connect-limitation. 35DT controls enabling/disabling module. 36${LINUX}/arch/arm/boot/dts/r8a7790-lager.dts can be good example. 37This is example of 38 39Playback: [MEM] -> [SRC2] -> [DVC0] -> [SSIU0/SSI0] -> [codec] 40Capture: [MEM] <- [DVC1] <- [SRC3] <- [SSIU1/SSI1] <- [codec] 41 42 &rcar_sound { 43 ... 44 rcar_sound,dai { 45 dai0 { 46 playback = <&ssi0 &src2 &dvc0>; 47 capture = <&ssi1 &src3 &dvc1>; 48 }; 49 }; 50 }; 51 52You can use below. 53${LINUX}/arch/arm/boot/dts/r8a7790.dts can be good example. 54 55 &src0 &ctu00 &mix0 &dvc0 &ssi0 56 &src1 &ctu01 &mix1 &dvc1 &ssi1 57 &src2 &ctu02 &ssi2 58 &src3 &ctu03 &ssi3 59 &src4 &ssi4 60 &src5 &ctu10 &ssi5 61 &src6 &ctu11 &ssi6 62 &src7 &ctu12 &ssi7 63 &src8 &ctu13 &ssi8 64 &src9 &ssi9 65 66============================================= 67* SRC (Sampling Rate Converter) 68============================================= 69 70 [xx]Hz [yy]Hz 71 ------> [SRC] ------> 72 73SRC can convert [xx]Hz to [yy]Hz. Then, it has below 2 modes 74 75 Asynchronous mode: input data / output data are based on different clocks. 76 you can use this mode on Playback / Capture 77 Synchronous mode: input data / output data are based on same clocks. 78 This mode will be used if system doesn't have its input clock, 79 for example digital TV case. 80 you can use this mode on Playback 81 82------------------ 83** Asynchronous mode 84------------------ 85 86You need to use "simple-scu-audio-card" sound card for it. 87example) 88 89 sound { 90 compatible = "simple-scu-audio-card"; 91 ... 92 /* 93 * SRC Asynchronous mode setting 94 * Playback: 95 * All input data will be converted to 48kHz 96 * Capture: 97 * Inputed 48kHz data will be converted to 98 * system specified Hz 99 */ 100 simple-audio-card,convert-rate = <48000>; 101 ... 102 simple-audio-card,cpu { 103 sound-dai = <&rcar_sound>; 104 }; 105 simple-audio-card,codec { 106 ... 107 }; 108 }; 109 110------------------ 111** Synchronous mode 112------------------ 113 114 > amixer set "SRC Out Rate" on 115 > aplay xxxx.wav 116 > amixer set "SRC Out Rate" 48000 117 > amixer set "SRC Out Rate" 44100 118 119============================================= 120* CTU (Channel Transfer Unit) 121============================================= 122 123 [xx]ch [yy]ch 124 ------> [CTU] --------> 125 126CTU can convert [xx]ch to [yy]ch, or exchange outputed channel. 127CTU conversion needs matrix settings. 128For more detail information, see below 129 130 Renesas R-Car datasheet 131 - Sampling Rate Converter Unit (SCU) 132 - SCU Operation 133 - CMD Block 134 - Functional Blocks in CMD 135 136 Renesas R-Car datasheet 137 - Sampling Rate Converter Unit (SCU) 138 - Register Description 139 - CTUn Scale Value exx Register (CTUn_SVxxR) 140 141 ${LINUX}/sound/soc/sh/rcar/ctu.c 142 - comment of header 143 144You need to use "simple-scu-audio-card" sound card for it. 145example) 146 147 sound { 148 compatible = "simple-scu-audio-card"; 149 ... 150 /* 151 * CTU setting 152 * All input data will be converted to 2ch 153 * as output data 154 */ 155 simple-audio-card,convert-channels = <2>; 156 ... 157 simple-audio-card,cpu { 158 sound-dai = <&rcar_sound>; 159 }; 160 simple-audio-card,codec { 161 ... 162 }; 163 }; 164 165Ex) Exchange output channel 166 Input -> Output 167 1ch -> 0ch 168 0ch -> 1ch 169 170 example of using matrix 171 output 0ch = (input 0ch x 0) + (input 1ch x 1) 172 output 1ch = (input 0ch x 1) + (input 1ch x 0) 173 174 amixer set "CTU Reset" on 175 amixer set "CTU Pass" 9,10 176 amixer set "CTU SV0" 0,4194304 177 amixer set "CTU SV1" 4194304,0 178 179 example of changing connection 180 amixer set "CTU Reset" on 181 amixer set "CTU Pass" 2,1 182 183============================================= 184* MIX (Mixer) 185============================================= 186 187MIX merges 2 sounds path. You can see 2 sound interface on system, 188and these sounds will be merged by MIX. 189 190 aplay -D plughw:0,0 xxxx.wav & 191 aplay -D plughw:0,1 yyyy.wav 192 193You need to use "simple-scu-audio-card" sound card for it. 194Ex) 195 [MEM] -> [SRC1] -> [CTU02] -+-> [MIX0] -> [DVC0] -> [SSI0] 196 | 197 [MEM] -> [SRC2] -> [CTU03] -+ 198 199 sound { 200 #address-cells = <1>; 201 #size-cells = <0>; 202 203 compatible = "simple-scu-audio-card"; 204 ... 205 simple-audio-card,cpu@0 { 206 reg = <0>; 207 sound-dai = <&rcar_sound 0>; 208 }; 209 simple-audio-card,cpu@1 { 210 reg = <1>; 211 sound-dai = <&rcar_sound 1>; 212 }; 213 simple-audio-card,codec { 214 ... 215 }; 216 }; 217 218 &rcar_sound { 219 ... 220 rcar_sound,dai { 221 dai0 { 222 playback = <&src1 &ctu02 &mix0 &dvc0 &ssi0>; 223 }; 224 dai1 { 225 playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>; 226 }; 227 }; 228 }; 229 230============================================= 231* DVC (Digital Volume and Mute Function) 232============================================= 233 234DVC controls Playback/Capture volume. 235 236Playback Volume 237 amixer set "DVC Out" 100% 238 239Capture Volume 240 amixer set "DVC In" 100% 241 242Playback Mute 243 amixer set "DVC Out Mute" on 244 245Capture Mute 246 amixer set "DVC In Mute" on 247 248Volume Ramp 249 amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps" 250 amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps" 251 amixer set "DVC Out Ramp" on 252 aplay xxx.wav & 253 amixer set "DVC Out" 80% // Volume Down 254 amixer set "DVC Out" 100% // Volume Up 255 256============================================= 257* SSIU (Serial Sound Interface Unit) 258============================================= 259 260There is no DT settings for SSIU, because SSIU will be automatically 261selected via SSI. 262SSIU can avoid some under/over run error, because it has some buffer. 263But you can't use it if SSI was PIO mode. 264In DMA mode, you can select not to use SSIU by using "no-busif" on DT. 265 266 &ssi0 { 267 no-busif; 268 }; 269 270============================================= 271* SSI (Serial Sound Interface) 272============================================= 273 274** PIO mode 275 276You can use PIO mode which is for connection check by using. 277Note: The system will drop non-SSI modules in PIO mode 278even though if DT is selecting other modules. 279 280 &ssi0 { 281 pio-transfer 282 }; 283 284** DMA mode without SSIU 285 286You can use DMA without SSIU. 287Note: under/over run, or noise are likely to occur 288 289 &ssi0 { 290 no-busif; 291 }; 292 293** PIN sharing 294 295Each SSI can share WS pin. It is based on platform. 296This is example if SSI1 want to share WS pin with SSI0 297 298 &ssi1 { 299 shared-pin; 300 }; 301 302** Multi-SSI 303 304You can use Multi-SSI. 305This is example of SSI0/SSI1/SSI2 (= for 6ch) 306 307 &rcar_sound { 308 ... 309 rcar_sound,dai { 310 dai0 { 311 playback = <&ssi0 &ssi1 &ssi2 &src0 &dvc0>; 312 }; 313 }; 314 }; 315 316** TDM-SSI 317 318You can use TDM with SSI. 319This is example of TDM 6ch. 320Driver can automatically switches TDM <-> stereo mode in this case. 321 322 rsnd_tdm: sound { 323 compatible = "simple-audio-card"; 324 ... 325 simple-audio-card,cpu { 326 /* system can use TDM 6ch */ 327 dai-tdm-slot-num = <6>; 328 sound-dai = <&rcar_sound>; 329 }; 330 simple-audio-card,codec { 331 ... 332 }; 333 }; 334 335 336============================================= 337Required properties: 338============================================= 339 340- compatible : "renesas,rcar_sound-<soctype>", fallbacks 341 "renesas,rcar_sound-gen1" if generation1, and 342 "renesas,rcar_sound-gen2" if generation2 (or RZ/G1) 343 "renesas,rcar_sound-gen3" if generation3 344 Examples with soctypes are: 345 - "renesas,rcar_sound-r8a7743" (RZ/G1M) 346 - "renesas,rcar_sound-r8a7745" (RZ/G1E) 347 - "renesas,rcar_sound-r8a7778" (R-Car M1A) 348 - "renesas,rcar_sound-r8a7779" (R-Car H1) 349 - "renesas,rcar_sound-r8a7790" (R-Car H2) 350 - "renesas,rcar_sound-r8a7791" (R-Car M2-W) 351 - "renesas,rcar_sound-r8a7793" (R-Car M2-N) 352 - "renesas,rcar_sound-r8a7794" (R-Car E2) 353 - "renesas,rcar_sound-r8a7795" (R-Car H3) 354 - "renesas,rcar_sound-r8a7796" (R-Car M3-W) 355- reg : Should contain the register physical address. 356 required register is 357 SRU/ADG/SSI if generation1 358 SRU/ADG/SSIU/SSI if generation2 359- rcar_sound,ssi : Should contain SSI feature. 360 The number of SSI subnode should be same as HW. 361 see below for detail. 362- rcar_sound,src : Should contain SRC feature. 363 The number of SRC subnode should be same as HW. 364 see below for detail. 365- rcar_sound,ctu : Should contain CTU feature. 366 The number of CTU subnode should be same as HW. 367 see below for detail. 368- rcar_sound,mix : Should contain MIX feature. 369 The number of MIX subnode should be same as HW. 370 see below for detail. 371- rcar_sound,dvc : Should contain DVC feature. 372 The number of DVC subnode should be same as HW. 373 see below for detail. 374- rcar_sound,dai : DAI contents. 375 The number of DAI subnode should be same as HW. 376 see below for detail. 377- #sound-dai-cells : it must be 0 if your system is using single DAI 378 it must be 1 if your system is using multi DAI 379- clocks : References to SSI/SRC/MIX/CTU/DVC/AUDIO_CLK clocks. 380- clock-names : List of necessary clock names. 381 "ssi-all", "ssi.X", "src.X", "mix.X", "ctu.X", 382 "dvc.X", "clk_a", "clk_b", "clk_c", "clk_i" 383 384Optional properties: 385- #clock-cells : it must be 0 if your system has audio_clkout 386 it must be 1 if your system has audio_clkout0/1/2/3 387- clock-frequency : for all audio_clkout0/1/2/3 388- clkout-lr-asynchronous : boolean property. it indicates that audio_clkoutn 389 is asynchronizes with lr-clock. 390- resets : References to SSI resets. 391- reset-names : List of valid reset names. 392 "ssi-all", "ssi.X" 393 394SSI subnode properties: 395- interrupts : Should contain SSI interrupt for PIO transfer 396- shared-pin : if shared clock pin 397- pio-transfer : use PIO transfer mode 398- no-busif : BUSIF is not ussed when [mem -> SSI] via DMA case 399- dma : Should contain Audio DMAC entry 400- dma-names : SSI case "rx" (=playback), "tx" (=capture) 401 SSIU case "rxu" (=playback), "txu" (=capture) 402 403SRC subnode properties: 404- dma : Should contain Audio DMAC entry 405- dma-names : "rx" (=playback), "tx" (=capture) 406 407DVC subnode properties: 408- dma : Should contain Audio DMAC entry 409- dma-names : "tx" (=playback/capture) 410 411DAI subnode properties: 412- playback : list of playback modules 413- capture : list of capture modules 414 415 416============================================= 417Example: 418============================================= 419 420rcar_sound: sound@ec500000 { 421 #sound-dai-cells = <1>; 422 compatible = "renesas,rcar_sound-r8a7791", "renesas,rcar_sound-gen2"; 423 reg = <0 0xec500000 0 0x1000>, /* SCU */ 424 <0 0xec5a0000 0 0x100>, /* ADG */ 425 <0 0xec540000 0 0x1000>, /* SSIU */ 426 <0 0xec541000 0 0x1280>, /* SSI */ 427 <0 0xec740000 0 0x200>; /* Audio DMAC peri peri*/ 428 reg-names = "scu", "adg", "ssiu", "ssi", "audmapp"; 429 430 clocks = <&mstp10_clks R8A7790_CLK_SSI_ALL>, 431 <&mstp10_clks R8A7790_CLK_SSI9>, <&mstp10_clks R8A7790_CLK_SSI8>, 432 <&mstp10_clks R8A7790_CLK_SSI7>, <&mstp10_clks R8A7790_CLK_SSI6>, 433 <&mstp10_clks R8A7790_CLK_SSI5>, <&mstp10_clks R8A7790_CLK_SSI4>, 434 <&mstp10_clks R8A7790_CLK_SSI3>, <&mstp10_clks R8A7790_CLK_SSI2>, 435 <&mstp10_clks R8A7790_CLK_SSI1>, <&mstp10_clks R8A7790_CLK_SSI0>, 436 <&mstp10_clks R8A7790_CLK_SCU_SRC9>, <&mstp10_clks R8A7790_CLK_SCU_SRC8>, 437 <&mstp10_clks R8A7790_CLK_SCU_SRC7>, <&mstp10_clks R8A7790_CLK_SCU_SRC6>, 438 <&mstp10_clks R8A7790_CLK_SCU_SRC5>, <&mstp10_clks R8A7790_CLK_SCU_SRC4>, 439 <&mstp10_clks R8A7790_CLK_SCU_SRC3>, <&mstp10_clks R8A7790_CLK_SCU_SRC2>, 440 <&mstp10_clks R8A7790_CLK_SCU_SRC1>, <&mstp10_clks R8A7790_CLK_SCU_SRC0>, 441 <&mstp10_clks R8A7790_CLK_SCU_DVC0>, <&mstp10_clks R8A7790_CLK_SCU_DVC1>, 442 <&audio_clk_a>, <&audio_clk_b>, <&audio_clk_c>, <&m2_clk>; 443 clock-names = "ssi-all", 444 "ssi.9", "ssi.8", "ssi.7", "ssi.6", "ssi.5", 445 "ssi.4", "ssi.3", "ssi.2", "ssi.1", "ssi.0", 446 "src.9", "src.8", "src.7", "src.6", "src.5", 447 "src.4", "src.3", "src.2", "src.1", "src.0", 448 "dvc.0", "dvc.1", 449 "clk_a", "clk_b", "clk_c", "clk_i"; 450 451 rcar_sound,dvc { 452 dvc0: dvc-0 { 453 dmas = <&audma0 0xbc>; 454 dma-names = "tx"; 455 }; 456 dvc1: dvc-1 { 457 dmas = <&audma0 0xbe>; 458 dma-names = "tx"; 459 }; 460 }; 461 462 rcar_sound,mix { 463 mix0: mix-0 { }; 464 mix1: mix-1 { }; 465 }; 466 467 rcar_sound,ctu { 468 ctu00: ctu-0 { }; 469 ctu01: ctu-1 { }; 470 ctu02: ctu-2 { }; 471 ctu03: ctu-3 { }; 472 ctu10: ctu-4 { }; 473 ctu11: ctu-5 { }; 474 ctu12: ctu-6 { }; 475 ctu13: ctu-7 { }; 476 }; 477 478 rcar_sound,src { 479 src0: src-0 { 480 interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; 481 dmas = <&audma0 0x85>, <&audma1 0x9a>; 482 dma-names = "rx", "tx"; 483 }; 484 src1: src-1 { 485 interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; 486 dmas = <&audma0 0x87>, <&audma1 0x9c>; 487 dma-names = "rx", "tx"; 488 }; 489 src2: src-2 { 490 interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; 491 dmas = <&audma0 0x89>, <&audma1 0x9e>; 492 dma-names = "rx", "tx"; 493 }; 494 src3: src-3 { 495 interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; 496 dmas = <&audma0 0x8b>, <&audma1 0xa0>; 497 dma-names = "rx", "tx"; 498 }; 499 src4: src-4 { 500 interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; 501 dmas = <&audma0 0x8d>, <&audma1 0xb0>; 502 dma-names = "rx", "tx"; 503 }; 504 src5: src-5 { 505 interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; 506 dmas = <&audma0 0x8f>, <&audma1 0xb2>; 507 dma-names = "rx", "tx"; 508 }; 509 src6: src-6 { 510 interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; 511 dmas = <&audma0 0x91>, <&audma1 0xb4>; 512 dma-names = "rx", "tx"; 513 }; 514 src7: src-7 { 515 interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; 516 dmas = <&audma0 0x93>, <&audma1 0xb6>; 517 dma-names = "rx", "tx"; 518 }; 519 src8: src-8 { 520 interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; 521 dmas = <&audma0 0x95>, <&audma1 0xb8>; 522 dma-names = "rx", "tx"; 523 }; 524 src9: src-9 { 525 interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; 526 dmas = <&audma0 0x97>, <&audma1 0xba>; 527 dma-names = "rx", "tx"; 528 }; 529 }; 530 531 rcar_sound,ssi { 532 ssi0: ssi-0 { 533 interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; 534 dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>; 535 dma-names = "rx", "tx", "rxu", "txu"; 536 }; 537 ssi1: ssi-1 { 538 interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; 539 dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>; 540 dma-names = "rx", "tx", "rxu", "txu"; 541 }; 542 ssi2: ssi-2 { 543 interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; 544 dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>; 545 dma-names = "rx", "tx", "rxu", "txu"; 546 }; 547 ssi3: ssi-3 { 548 interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; 549 dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>; 550 dma-names = "rx", "tx", "rxu", "txu"; 551 }; 552 ssi4: ssi-4 { 553 interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; 554 dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>; 555 dma-names = "rx", "tx", "rxu", "txu"; 556 }; 557 ssi5: ssi-5 { 558 interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; 559 dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>; 560 dma-names = "rx", "tx", "rxu", "txu"; 561 }; 562 ssi6: ssi-6 { 563 interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; 564 dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>; 565 dma-names = "rx", "tx", "rxu", "txu"; 566 }; 567 ssi7: ssi-7 { 568 interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; 569 dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>; 570 dma-names = "rx", "tx", "rxu", "txu"; 571 }; 572 ssi8: ssi-8 { 573 interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; 574 dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>; 575 dma-names = "rx", "tx", "rxu", "txu"; 576 }; 577 ssi9: ssi-9 { 578 interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; 579 dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>; 580 dma-names = "rx", "tx", "rxu", "txu"; 581 }; 582 }; 583 584 rcar_sound,dai { 585 dai0 { 586 playback = <&ssi5 &src5>; 587 capture = <&ssi6>; 588 }; 589 dai1 { 590 playback = <&ssi3>; 591 }; 592 dai2 { 593 capture = <&ssi4>; 594 }; 595 dai3 { 596 playback = <&ssi7>; 597 }; 598 dai4 { 599 capture = <&ssi8>; 600 }; 601 }; 602}; 603 604============================================= 605Example: simple sound card 606============================================= 607 608 rsnd_ak4643: sound { 609 compatible = "simple-audio-card"; 610 611 simple-audio-card,format = "left_j"; 612 simple-audio-card,bitclock-master = <&sndcodec>; 613 simple-audio-card,frame-master = <&sndcodec>; 614 615 sndcpu: simple-audio-card,cpu { 616 sound-dai = <&rcar_sound>; 617 }; 618 619 sndcodec: simple-audio-card,codec { 620 sound-dai = <&ak4643>; 621 clocks = <&audio_clock>; 622 }; 623 }; 624 625&rcar_sound { 626 pinctrl-0 = <&sound_pins &sound_clk_pins>; 627 pinctrl-names = "default"; 628 629 /* Single DAI */ 630 #sound-dai-cells = <0>; 631 632 633 rcar_sound,dai { 634 dai0 { 635 playback = <&ssi0 &src2 &dvc0>; 636 capture = <&ssi1 &src3 &dvc1>; 637 }; 638 }; 639}; 640 641&ssi1 { 642 shared-pin; 643}; 644 645============================================= 646Example: simple sound card for TDM 647============================================= 648 649 rsnd_tdm: sound { 650 compatible = "simple-audio-card"; 651 652 simple-audio-card,format = "left_j"; 653 simple-audio-card,bitclock-master = <&sndcodec>; 654 simple-audio-card,frame-master = <&sndcodec>; 655 656 sndcpu: simple-audio-card,cpu { 657 sound-dai = <&rcar_sound>; 658 dai-tdm-slot-num = <6>; 659 }; 660 661 sndcodec: simple-audio-card,codec { 662 sound-dai = <&xxx>; 663 }; 664 }; 665 666============================================= 667Example: simple sound card for Multi channel 668============================================= 669 670&rcar_sound { 671 pinctrl-0 = <&sound_pins &sound_clk_pins>; 672 pinctrl-names = "default"; 673 674 /* Single DAI */ 675 #sound-dai-cells = <0>; 676 677 678 rcar_sound,dai { 679 dai0 { 680 playback = <&ssi0 &ssi1 &ssi2 &src0 &dvc0>; 681 }; 682 }; 683}; 684