xref: /linux/Documentation/devicetree/bindings/sound/realtek,rt5645.yaml (revision 46e6acfe3501fa938af9c5bd730f0020235b08a2) 
1# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/sound/realtek,rt5645.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: RT5650/RT5645 audio CODEC
8
9maintainers:
10  - Animesh Agarwal <animeshagarwal28@gmail.com>
11
12description: |
13  This device supports I2C only.
14
15  Pins on the device (for linking into audio routes) for RT5645/RT5650:
16    * DMIC L1
17    * DMIC R1
18    * DMIC L2
19    * DMIC R2
20    * IN1P
21    * IN1N
22    * IN2P
23    * IN2N
24    * Haptic Generator
25    * HPOL
26    * HPOR
27    * LOUTL
28    * LOUTR
29    * PDM1L
30    * PDM1R
31    * SPOL
32    * SPOR
33
34allOf:
35  - $ref: dai-common.yaml#
36
37properties:
38  compatible:
39    enum:
40      - realtek,rt5645
41      - realtek,rt5650
42
43  reg:
44    maxItems: 1
45
46  interrupts:
47    maxItems: 1
48    description: The CODEC's interrupt output.
49
50  avdd-supply:
51    description: Power supply for AVDD, providing 1.8V.
52
53  cpvdd-supply:
54    description: Power supply for CPVDD, providing 3.5V.
55
56  hp-detect-gpios:
57    description:
58      A GPIO spec for the external headphone detect pin. If jd-mode = 0, we
59      will get the JD status by getting the value of hp-detect-gpios.
60    maxItems: 1
61
62  cbj-sleeve-gpios:
63    description:
64      A GPIO spec to control the external combo jack circuit to tie the
65      sleeve/ring2 contacts to the ground or floating. It could avoid some
66      electric noise from the active speaker jacks.
67    maxItems: 1
68
69  realtek,in2-differential:
70    description:
71      Indicate MIC2 input are differential, rather than single-ended.
72    type: boolean
73
74  realtek,dmic1-data-pin:
75    description: Specify which pin to be used as DMIC1 data pin.
76    $ref: /schemas/types.yaml#/definitions/uint32
77    enum:
78      - 0 # dmic1 is not used
79      - 1 # using IN2P pin as dmic1 data pin
80      - 2 # using GPIO6 pin as dmic1 data pin
81      - 3 # using GPIO10 pin as dmic1 data pin
82      - 4 # using GPIO12 pin as dmic1 data pin
83
84  realtek,dmic2-data-pin:
85    description: Specify which pin to be used as DMIC2 data pin.
86    $ref: /schemas/types.yaml#/definitions/uint32
87    enum:
88      - 0 # dmic2 is not used
89      - 1 # using IN2N pin as dmic2 data pin
90      - 2 # using GPIO5 pin as dmic2 data pin
91      - 3 # using GPIO11 pin as dmic2 data pin
92
93  realtek,jd-mode:
94    description: The JD mode of rt5645/rt5650.
95    $ref: /schemas/types.yaml#/definitions/uint32
96    enum:
97      - 0 # rt5645/rt5650 JD function is not used
98      - 1 # Mode-0 (VDD=3.3V), two port jack detection
99      - 2 # Mode-1 (VDD=3.3V), one port jack detection
100      - 3 # Mode-2 (VDD=1.8V), one port jack detection
101
102required:
103  - compatible
104  - reg
105  - interrupts
106  - avdd-supply
107  - cpvdd-supply
108
109unevaluatedProperties: false
110
111examples:
112  - |
113    #include <dt-bindings/gpio/gpio.h>
114    #include <dt-bindings/interrupt-controller/irq.h>
115
116    i2c {
117        #address-cells = <1>;
118        #size-cells = <0>;
119
120        codec@1a {
121            compatible = "realtek,rt5650";
122            reg = <0x1a>;
123            hp-detect-gpios = <&gpio 19 0>;
124            cbj-sleeve-gpios = <&gpio 20 0>;
125            interrupt-parent = <&gpio>;
126            interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
127            avdd-supply = <&avdd_reg>;
128            cpvdd-supply = <&cpvdd_supply>;
129            realtek,jd-mode = <3>;
130        };
131    };
132