1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/sound/cirrus,cs42l42.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: Cirrus Logic CS42L42 audio CODEC 8 9maintainers: 10 - patches@opensource.cirrus.com 11 12description: 13 The CS42L42 is a low-power audio codec designed for portable applications. 14 It provides a high-dynamic range, stereo DAC for audio playback and a mono 15 high-dynamic-range ADC for audio capture. There is an integrated headset 16 detection block. 17 18properties: 19 compatible: 20 enum: 21 - cirrus,cs42l42 22 - cirrus,cs42l83 23 24 reg: 25 description: 26 The I2C address of the CS42L42. 27 maxItems: 1 28 29 VP-supply: 30 description: 31 VP power supply. 32 33 VCP-supply: 34 description: 35 Charge pump power supply. 36 37 VD_FILT-supply: 38 description: 39 FILT+ power supply. 40 41 VL-supply: 42 description: 43 Logic power supply. 44 45 VA-supply: 46 description: 47 Analog power supply. 48 49 reset-gpios: 50 description: 51 This pin will be asserted and then deasserted to reset the 52 CS42L42 before communication starts. 53 maxItems: 1 54 55 interrupts: 56 description: 57 Interrupt for CS42L42 IRQ line. 58 maxItems: 1 59 60 cirrus,ts-inv: 61 description: | 62 Sets the behaviour of the jack plug detect switch. 63 64 0 - (Default) Shorted to tip when unplugged, open when plugged. 65 This is "inverted tip sense (ITS)" in the datasheet. 66 67 1 - Open when unplugged, shorted to tip when plugged. 68 This is "normal tip sense (TS)" in the datasheet. 69 70 The CS42L42_TS_INV_* defines are available for this. 71 $ref: "/schemas/types.yaml#/definitions/uint32" 72 minimum: 0 73 maximum: 1 74 75 cirrus,ts-dbnc-rise: 76 description: | 77 Debounce the rising edge of TIP_SENSE_PLUG. With no 78 debounce, the tip sense pin might be noisy on a plug event. 79 80 0 - 0ms 81 1 - 125ms 82 2 - 250ms 83 3 - 500ms 84 4 - 750ms 85 5 - 1s (Default) 86 6 - 1.25s 87 7 - 1.5s 88 89 The CS42L42_TS_DBNCE_* defines are available for this. 90 $ref: "/schemas/types.yaml#/definitions/uint32" 91 minimum: 0 92 maximum: 7 93 94 cirrus,ts-dbnc-fall: 95 description: | 96 Debounce the falling edge of TIP_SENSE_UNPLUG. With no 97 debounce, the tip sense pin might be noisy on an unplug event. 98 99 0 - 0ms 100 1 - 125ms 101 2 - 250ms 102 3 - 500ms 103 4 - 750ms 104 5 - 1s (Default) 105 6 - 1.25s 106 7 - 1.5s 107 108 The CS42L42_TS_DBNCE_* defines are available for this. 109 $ref: "/schemas/types.yaml#/definitions/uint32" 110 minimum: 0 111 maximum: 7 112 113 cirrus,btn-det-init-dbnce: 114 description: | 115 This sets how long to wait after enabling button detection 116 interrupts before servicing button interrupts, to allow the 117 HS bias time to settle. Value is in milliseconds. 118 There may be erroneous button interrupts if this debounce time 119 is too short. 120 121 0ms - 200ms, 122 Default = 100ms 123 $ref: "/schemas/types.yaml#/definitions/uint32" 124 minimum: 0 125 maximum: 200 126 127 cirrus,btn-det-event-dbnce: 128 description: | 129 This sets how long to wait after receiving a button press 130 interrupt before processing it. Allows time for the button 131 press to make a clean connection with the bias resistors. 132 Value is in milliseconds. 133 134 0ms - 20ms, 135 Default = 10ms 136 $ref: "/schemas/types.yaml#/definitions/uint32" 137 minimum: 0 138 maximum: 20 139 140 cirrus,bias-lvls: 141 description: | 142 For a level-detect headset button scheme, each button will bias 143 the mic pin to a certain voltage. To determine which button was 144 pressed, the voltage is compared to sequential, decreasing 145 voltages, until the compared voltage < bias voltage. 146 For different hardware setups, a designer might want to tweak this. 147 This is an array of descending values for the comparator voltage, 148 given as percent of the HSBIAS voltage. 149 150 Array of 4 values, each 0-63 151 < x1 x2 x3 x4 > 152 Default = < 15 8 4 1 > 153 $ref: /schemas/types.yaml#/definitions/uint32-array 154 minItems: 4 155 maxItems: 4 156 items: 157 minimum: 0 158 maximum: 63 159 160 cirrus,hs-bias-ramp-rate: 161 description: | 162 If present this sets the rate that the HS bias should rise and fall. 163 The actual rise and fall times depend on external hardware (the 164 datasheet gives several rise and fall time examples). 165 166 0 - Fast rise time; slow, load-dependent fall time 167 1 - Fast 168 2 - Slow (default) 169 3 - Slowest 170 171 The CS42L42_HSBIAS_RAMP_* defines are available for this. 172 $ref: "/schemas/types.yaml#/definitions/uint32" 173 minimum: 0 174 maximum: 3 175 176 cirrus,hs-bias-sense-disable: 177 description: | 178 If present the HSBIAS sense is disabled. Configures HSBIAS output 179 current sense through the external 2.21-k resistor. HSBIAS_SENSE 180 is a hardware feature to reduce the potential pop noise when the 181 headset plug is removed slowly. But on some platforms ESD voltage 182 will affect it causing plug detection to fail, especially with CTIA 183 headset type. For different hardware setups, a designer might want 184 to tweak default behavior. 185 type: boolean 186 187required: 188 - compatible 189 - reg 190 - VP-supply 191 - VCP-supply 192 - VD_FILT-supply 193 - VL-supply 194 - VA-supply 195 196additionalProperties: false 197 198examples: 199 - | 200 #include <dt-bindings/sound/cs42l42.h> 201 i2c { 202 #address-cells = <1>; 203 #size-cells = <0>; 204 205 cs42l42: cs42l42@48 { 206 compatible = "cirrus,cs42l42"; 207 reg = <0x48>; 208 VA-supply = <&dummy_vreg>; 209 VP-supply = <&dummy_vreg>; 210 VCP-supply = <&dummy_vreg>; 211 VD_FILT-supply = <&dummy_vreg>; 212 VL-supply = <&dummy_vreg>; 213 214 reset-gpios = <&axi_gpio_0 1 0>; 215 interrupt-parent = <&gpio0>; 216 interrupts = <55 8>; 217 218 cirrus,ts-inv = <CS42L42_TS_INV_DIS>; 219 cirrus,ts-dbnc-rise = <CS42L42_TS_DBNCE_1000>; 220 cirrus,ts-dbnc-fall = <CS42L42_TS_DBNCE_0>; 221 cirrus,btn-det-init-dbnce = <100>; 222 cirrus,btn-det-event-dbnce = <10>; 223 cirrus,bias-lvls = <0x0F 0x08 0x04 0x01>; 224 cirrus,hs-bias-ramp-rate = <CS42L42_HSBIAS_RAMP_SLOW>; 225 }; 226 }; 227