xref: /linux/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.yaml (revision be3382ecdf317f005e7d47356d0a9256cc36dd88) 
1# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/serial/qcom,msm-uartdm.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Qualcomm MSM Serial UARTDM
8
9maintainers:
10  - Andy Gross <agross@kernel.org>
11  - Bjorn Andersson <bjorn.andersson@linaro.org>
12  - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
13
14description: |
15  The MSM serial UARTDM hardware is designed for high-speed use cases where the
16  transmit and/or receive channels can be offloaded to a dma-engine. From a
17  software perspective it's mostly compatible with the MSM serial UART except
18  that it supports reading and writing multiple characters at a time.
19
20  Note:: Aliases may be defined to ensure the correct ordering of the UARTs.
21  The alias serialN will result in the UART being assigned port N.  If any
22  serialN alias exists, then an alias must exist for each enabled UART.  The
23  serialN aliases should be in a .dts file instead of in a .dtsi file.
24
25properties:
26  compatible:
27    items:
28      - enum:
29          - qcom,msm-uartdm-v1.1
30          - qcom,msm-uartdm-v1.2
31          - qcom,msm-uartdm-v1.3
32          - qcom,msm-uartdm-v1.4
33      - const: qcom,msm-uartdm
34
35  clocks:
36    maxItems: 2
37
38  clock-names:
39    items:
40      - const: core
41      - const: iface
42
43  dmas:
44    maxItems: 2
45
46  dma-names:
47    items:
48      - const: tx
49      - const: rx
50
51  interconnects:
52    maxItems: 1
53
54  interrupts:
55    maxItems: 1
56
57  operating-points-v2: true
58
59  power-domains:
60    maxItems: 1
61
62  qcom,rx-crci:
63    $ref: /schemas/types.yaml#/definitions/uint32
64    description:
65      Identificator for Client Rate Control Interface to be used with RX DMA
66      channel. Required when using DMA for reception with UARTDM v1.3 and
67      below.
68
69  qcom,tx-crci:
70    $ref: /schemas/types.yaml#/definitions/uint32
71    description:
72      Identificator for Client Rate Control Interface to be used with TX DMA
73      channel. Required when using DMA for transmission with UARTDM v1.3 and
74      below.
75
76  reg:
77    minItems: 1
78    items:
79      - description: Main control registers
80      - description: An optional second register location shall specify the GSBI control region.
81
82required:
83  - compatible
84  - clock-names
85  - clocks
86  - interrupts
87  - reg
88
89allOf:
90  - $ref: /schemas/serial/serial.yaml#
91
92  - if:
93      properties:
94        compatible:
95          contains:
96            const: qcom,msm-uartdm-v1.3
97    then:
98      properties:
99        reg:
100          minItems: 2
101    else:
102      properties:
103        reg:
104          maxItems: 1
105
106unevaluatedProperties: false
107
108examples:
109  - |
110    #include <dt-bindings/interconnect/qcom,msm8996.h>
111    #include <dt-bindings/interrupt-controller/arm-gic.h>
112    #include <dt-bindings/power/qcom-rpmpd.h>
113
114    serial@f991e000 {
115        compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
116        reg = <0xf991e000 0x1000>;
117        interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
118        clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>;
119        clock-names = "core", "iface";
120        dmas = <&dma0 0>, <&dma0 1>;
121        dma-names = "tx", "rx";
122        power-domains = <&rpmpd MSM8996_VDDCX>;
123        operating-points-v2 = <&uart_opp_table>;
124        interconnects = <&pnoc MASTER_BLSP_1 &bimc SLAVE_EBI_CH0>;
125    };
126