1Qualcomm Hexagon Peripheral Image Loader 2 3This document defines the binding for a component that loads and boots firmware 4on the Qualcomm Hexagon core. 5 6- compatible: 7 Usage: required 8 Value type: <string> 9 Definition: must be one of: 10 "qcom,q6v5-pil", 11 "qcom,ipq8074-wcss-pil" 12 "qcom,msm8916-mss-pil", 13 "qcom,msm8974-mss-pil" 14 "qcom,msm8996-mss-pil" 15 "qcom,msm8998-mss-pil" 16 "qcom,sc7180-mss-pil" 17 "qcom,sdm845-mss-pil" 18 19- reg: 20 Usage: required 21 Value type: <prop-encoded-array> 22 Definition: must specify the base address and size of the qdsp6 and 23 rmb register blocks 24 25- reg-names: 26 Usage: required 27 Value type: <stringlist> 28 Definition: must be "q6dsp" and "rmb" 29 30- interrupts-extended: 31 Usage: required 32 Value type: <prop-encoded-array> 33 Definition: reference to the interrupts that match interrupt-names 34 35- interrupt-names: 36 Usage: required 37 Value type: <stringlist> 38 Definition: The interrupts needed depends on the the compatible 39 string: 40 qcom,q6v5-pil: 41 qcom,ipq8074-wcss-pil: 42 qcom,msm8916-mss-pil: 43 qcom,msm8974-mss-pil: 44 must be "wdog", "fatal", "ready", "handover", "stop-ack" 45 qcom,msm8996-mss-pil: 46 qcom,msm8998-mss-pil: 47 qcom,sc7180-mss-pil: 48 qcom,sdm845-mss-pil: 49 must be "wdog", "fatal", "ready", "handover", "stop-ack", 50 "shutdown-ack" 51 52- firmware-name: 53 Usage: optional 54 Value type: <stringlist> 55 Definition: must list the relative firmware image paths for mba and 56 modem. They are used for booting and authenticating the 57 Hexagon core. 58 59- clocks: 60 Usage: required 61 Value type: <phandle> 62 Definition: reference to the clocks that match clock-names 63 64- clock-names: 65 Usage: required 66 Value type: <stringlist> 67 Definition: The clocks needed depend on the compatible string: 68 qcom,ipq8074-wcss-pil: 69 no clock names required 70 qcom,q6v5-pil: 71 qcom,msm8916-mss-pil: 72 qcom,msm8974-mss-pil: 73 must be "iface", "bus", "mem", "xo" 74 qcom,msm8996-mss-pil: 75 must be "iface", "bus", "mem", "xo", "gpll0_mss", 76 "snoc_axi", "mnoc_axi", "pnoc", "qdss" 77 qcom,msm8998-mss-pil: 78 must be "iface", "bus", "mem", "xo", "gpll0_mss", 79 "snoc_axi", "mnoc_axi", "qdss" 80 qcom,sc7180-mss-pil: 81 must be "iface", "bus", "xo", "snoc_axi", "mnoc_axi", 82 "nav" 83 qcom,sdm845-mss-pil: 84 must be "iface", "bus", "mem", "xo", "gpll0_mss", 85 "snoc_axi", "mnoc_axi", "prng" 86 87- resets: 88 Usage: required 89 Value type: <phandle> 90 Definition: reference to the reset-controller for the modem sub-system 91 reference to the list of 3 reset-controllers for the 92 wcss sub-system 93 reference to the list of 2 reset-controllers for the modem 94 sub-system on SC7180, SDM845 SoCs 95 96- reset-names: 97 Usage: required 98 Value type: <stringlist> 99 Definition: must be "mss_restart" for the modem sub-system 100 must be "wcss_aon_reset", "wcss_reset", "wcss_q6_reset" 101 for the wcss sub-system 102 must be "mss_restart", "pdc_reset" for the modem 103 sub-system on SC7180, SDM845 SoCs 104 105For devices where the mba and mpss sub-nodes are not specified, mba/mpss region 106should be referenced as follows: 107- memory-region: 108 Usage: required 109 Value type: <phandle> 110 Definition: reference to the reserved-memory for the mba region followed 111 by the mpss region 112 113For the compatible strings below the following supplies are required: 114 "qcom,q6v5-pil" 115 "qcom,msm8916-mss-pil", 116- cx-supply: 117- mx-supply: 118- pll-supply: 119 Usage: required 120 Value type: <phandle> 121 Definition: reference to the regulators to be held on behalf of the 122 booting of the Hexagon core 123 124For the compatible string below the following supplies are required: 125 "qcom,msm8974-mss-pil" 126- cx-supply: 127- mss-supply: 128- mx-supply: 129- pll-supply: 130 Usage: required 131 Value type: <phandle> 132 Definition: reference to the regulators to be held on behalf of the 133 booting of the Hexagon core 134 135For the compatible string below the following supplies are required: 136 "qcom,msm8996-mss-pil" 137- pll-supply: 138 Usage: required 139 Value type: <phandle> 140 Definition: reference to the regulators to be held on behalf of the 141 booting of the Hexagon core 142 143- power-domains: 144 Usage: required 145 Value type: <phandle> 146 Definition: reference to power-domains that match power-domain-names 147 148- power-domain-names: 149 Usage: required 150 Value type: <stringlist> 151 Definition: The power-domains needed depend on the compatible string: 152 qcom,q6v5-pil: 153 qcom,ipq8074-wcss-pil: 154 qcom,msm8916-mss-pil: 155 qcom,msm8974-mss-pil: 156 no power-domain names required 157 qcom,msm8996-mss-pil: 158 qcom,msm8998-mss-pil: 159 must be "cx", "mx" 160 qcom,sc7180-mss-pil: 161 qcom,sdm845-mss-pil: 162 must be "cx", "mx", "mss", "load_state" 163 164- qcom,smem-states: 165 Usage: required 166 Value type: <phandle> 167 Definition: reference to the smem state for requesting the Hexagon to 168 shut down 169 170- qcom,smem-state-names: 171 Usage: required 172 Value type: <stringlist> 173 Definition: must be "stop" 174 175- qcom,halt-regs: 176 Usage: required 177 Value type: <prop-encoded-array> 178 Definition: a phandle reference to a syscon representing TCSR followed 179 by the three offsets within syscon for q6, modem and nc 180 halt registers. 181 182For the compatible strings below the following phandle references are required: 183 "qcom,sc7180-mss-pil" 184- qcom,spare-regs: 185 Usage: required 186 Value type: <prop-encoded-array> 187 Definition: a phandle reference to a syscon representing TCSR followed 188 by the offset within syscon for conn_box_spare0 register 189 used by the modem sub-system running on SC7180 SoC. 190 191The Hexagon node must contain iommus property as described in ../iommu/iommu.txt 192on platforms which do not have TrustZone. 193 194= SUBNODES: 195The Hexagon node must contain two subnodes, named "mba" and "mpss" representing 196the memory regions used by the Hexagon firmware. Each sub-node must contain: 197 198- memory-region: 199 Usage: required 200 Value type: <phandle> 201 Definition: reference to the reserved-memory for the region 202 203The Hexagon node may also have an subnode named either "smd-edge" or 204"glink-edge" that describes the communication edge, channels and devices 205related to the Hexagon. See ../soc/qcom/qcom,smd.txt and 206../soc/qcom/qcom,glink.txt for details on how to describe these. 207 208= EXAMPLE 209The following example describes the resources needed to boot control the 210Hexagon, as it is found on MSM8974 boards. 211 212 modem-rproc@fc880000 { 213 compatible = "qcom,q6v5-pil"; 214 reg = <0xfc880000 0x100>, 215 <0xfc820000 0x020>; 216 reg-names = "qdsp6", "rmb"; 217 218 interrupts-extended = <&intc 0 24 1>, 219 <&modem_smp2p_in 0 0>, 220 <&modem_smp2p_in 1 0>, 221 <&modem_smp2p_in 2 0>, 222 <&modem_smp2p_in 3 0>; 223 interrupt-names = "wdog", 224 "fatal", 225 "ready", 226 "handover", 227 "stop-ack"; 228 229 clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>, 230 <&gcc GCC_MSS_CFG_AHB_CLK>, 231 <&gcc GCC_BOOT_ROM_AHB_CLK>; 232 clock-names = "iface", "bus", "mem"; 233 234 qcom,halt-regs = <&tcsr_mutex_block 0x1180 0x1200 0x1280>; 235 236 resets = <&gcc GCC_MSS_RESTART>; 237 reset-names = "mss_restart"; 238 239 cx-supply = <&pm8841_s2>; 240 mss-supply = <&pm8841_s3>; 241 mx-supply = <&pm8841_s1>; 242 pll-supply = <&pm8941_l12>; 243 244 qcom,smem-states = <&modem_smp2p_out 0>; 245 qcom,smem-state-names = "stop"; 246 247 mba { 248 memory-region = <&mba_region>; 249 }; 250 251 mpss { 252 memory-region = <&mpss_region>; 253 }; 254 }; 255