1# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/regulator/rohm,bd71815-regulator.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: ROHM BD71815 Power Management Integrated Circuit regulators 8 9maintainers: 10 - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> 11 12description: | 13 This module is part of the ROHM BD718215 MFD device. For more details 14 see Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml. 15 16 The regulator controller is represented as a sub-node of the PMIC node 17 on the device tree. 18 19 The valid names for BD71815 regulator nodes are 20 buck1, buck2, buck3, buck4, buck5, 21 ldo1, ldo2, ldo3, ldo4, ldo5, 22 ldodvref, ldolpsr, wled 23 24properties: 25 wled: 26 type: object 27 description: 28 properties for wled regulator 29 $ref: regulator.yaml# 30 unevaluatedProperties: false 31 32 properties: 33 regulator-name: 34 const: wled 35 36patternProperties: 37 "^((ldo|buck)[1-5]|ldolpsr|ldodvref)$": 38 type: object 39 description: 40 Properties for single LDO/BUCK regulator. 41 $ref: regulator.yaml# 42 43 properties: 44 regulator-name: 45 pattern: "^((ldo|buck)[1-5]|ldolpsr|ldodvref)$" 46 description: 47 should be "ldo1", ..., "ldo5", "buck1", ..., "buck5" and "ldolpsr" 48 for ldolpsr regulator, "ldodvref" for ldodvref reglator. 49 50 rohm,vsel-gpios: 51 description: 52 GPIO used to control ldo4 state (when ldo4 is controlled by GPIO). 53 54 rohm,dvs-run-voltage: 55 description: 56 PMIC "RUN" state voltage in uV when PMIC HW states are used. See 57 comments below for bucks/LDOs which support this. 0 means 58 regulator should be disabled at RUN state. 59 $ref: "/schemas/types.yaml#/definitions/uint32" 60 minimum: 0 61 maximum: 3300000 62 63 rohm,dvs-snvs-voltage: 64 description: 65 Whether to keep regulator enabled at "SNVS" state or not. 66 0 means regulator should be disabled at SNVS state, non zero voltage 67 keeps regulator enabled. BD71815 does not change voltage level 68 when PMIC transitions to SNVS.SNVS voltage depends on the previous 69 state (from which the PMIC transitioned to SNVS). 70 $ref: "/schemas/types.yaml#/definitions/uint32" 71 minimum: 0 72 maximum: 3300000 73 74 rohm,dvs-suspend-voltage: 75 description: 76 PMIC "SUSPEND" state voltage in uV when PMIC HW states are used. See 77 comments below for bucks/LDOs which support this. 0 means 78 regulator should be disabled at SUSPEND state. 79 $ref: "/schemas/types.yaml#/definitions/uint32" 80 minimum: 0 81 maximum: 3300000 82 83 rohm,dvs-lpsr-voltage: 84 description: 85 PMIC "LPSR" state voltage in uV when PMIC HW states are used. See 86 comments below for bucks/LDOs which support this. 0 means 87 regulator should be disabled at LPSR state. 88 $ref: "/schemas/types.yaml#/definitions/uint32" 89 minimum: 0 90 maximum: 3300000 91 92 # Bucks 1 and 2 support giving separate voltages for operational states 93 # (RUN /CLEAN according to data-sheet) and non operational states 94 # (LPSR/SUSPEND). The voltage is automatically changed when HW 95 # state changes. Omitting these properties from bucks 1 and 2 leave 96 # buck voltages to not be toggled by HW state. Enable status may still 97 # be toggled by state changes depending on HW default settings. 98 # 99 # Bucks 3-5 and ldos 1-5 support setting the RUN state voltage here. 100 # Given RUN voltage is used at all states if regulator is enabled at 101 # given state. 102 # Values given for other states are regarded as enable/disable at 103 # given state (see below). 104 # 105 # All regulators except WLED support specifying enable/disable status 106 # for each of the HW states (RUN/SNVS/SUSPEND/LPSR). HW defaults can 107 # be overridden by setting voltage to 0 (regulator disabled at given 108 # state) or non-zero (regulator enabled at given state). Please note 109 # that setting non zero voltages for bucks 1/2 will also enable voltage 110 # changes according to state change. 111 112 required: 113 - regulator-name 114 115 unevaluatedProperties: false 116 117additionalProperties: false 118