1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/pinctrl/qcom,msm8909-tlmm.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: Qualcomm Technologies, Inc. MSM8909 TLMM block 8 9maintainers: 10 - Stephan Gerhold <stephan@gerhold.net> 11 12description: | 13 Top Level Mode Multiplexer pin controller in Qualcomm MSM8909 SoC. 14 15allOf: 16 - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# 17 18properties: 19 compatible: 20 const: qcom,msm8909-tlmm 21 22 reg: 23 maxItems: 1 24 25 interrupts: true 26 interrupt-controller: true 27 "#interrupt-cells": true 28 gpio-controller: true 29 gpio-reserved-ranges: true 30 "#gpio-cells": true 31 gpio-ranges: true 32 wakeup-parent: true 33 34required: 35 - compatible 36 - reg 37 38additionalProperties: false 39 40patternProperties: 41 "-state$": 42 oneOf: 43 - $ref: "#/$defs/qcom-msm8909-tlmm-state" 44 - patternProperties: 45 "-pins$": 46 $ref: "#/$defs/qcom-msm8909-tlmm-state" 47 additionalProperties: false 48 49$defs: 50 qcom-msm8909-tlmm-state: 51 type: object 52 description: 53 Pinctrl node's client devices use subnodes for desired pin configuration. 54 Client device subnodes use below standard properties. 55 $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state 56 57 properties: 58 pins: 59 description: 60 List of gpio pins affected by the properties specified in this 61 subnode. 62 items: 63 oneOf: 64 - pattern: "^gpio([0-9]|[1-9][0-9]|10[0-9]|11[0-7])$" 65 - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, 66 sdc2_data, qdsd_clk, qdsd_cmd, qdsd_data0, qdsd_data1, 67 qdsd_data2, qdsd_data3 ] 68 minItems: 1 69 maxItems: 16 70 71 function: 72 description: 73 Specify the alternative function to be configured for the specified 74 pins. 75 enum: [ adsp_ext, atest_bbrx0, atest_bbrx1, atest_char, atest_char0, 76 atest_char1, atest_char2, atest_char3, atest_combodac, 77 atest_gpsadc0, atest_gpsadc1, atest_wlan0, atest_wlan1, 78 bimc_dte0, bimc_dte1, blsp_i2c1, blsp_i2c2, blsp_i2c3, 79 blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_spi1, blsp_spi1_cs1, 80 blsp_spi1_cs2, blsp_spi1_cs3, blsp_spi2, blsp_spi2_cs1, 81 blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3, blsp_spi3_cs1, 82 blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4, blsp_spi5, blsp_spi6, 83 blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2, cam_mclk, 84 cci_async, cci_timer0, cci_timer1, cci_timer2, cdc_pdm0, 85 dbg_out, dmic0_clk, dmic0_data, ebi0_wrcdc, ebi2_a, ebi2_lcd, 86 ext_lpass, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, 87 gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gcc_plltest, gpio, 88 gsm0_tx, ldo_en, ldo_update, m_voc, mdp_vsync, modem_tsync, 89 nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, 90 pri_mi2s_data0_a, pri_mi2s_data0_b, pri_mi2s_data1_a, 91 pri_mi2s_data1_b, pri_mi2s_mclk_a, pri_mi2s_mclk_b, 92 pri_mi2s_sck_a, pri_mi2s_sck_b, pri_mi2s_ws_a, pri_mi2s_ws_b, 93 prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b, 94 pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a, 95 pwr_nav_enabled_b, qdss_cti_trig_in_a0, qdss_cti_trig_in_a1, 96 qdss_cti_trig_in_b0, qdss_cti_trig_in_b1, qdss_cti_trig_out_a0, 97 qdss_cti_trig_out_a1, qdss_cti_trig_out_b0, 98 qdss_cti_trig_out_b1, qdss_traceclk_a, qdss_tracectl_a, 99 qdss_tracedata_a, qdss_tracedata_b, sd_write, sec_mi2s, 100 smb_int, ssbi0, ssbi1, uim1_clk, uim1_data, uim1_present, 101 uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset, 102 uim3_clk, uim3_data, uim3_present, uim3_reset, uim_batt, 103 wcss_bt, wcss_fm, wcss_wlan ] 104 105 bias-disable: true 106 bias-pull-down: true 107 bias-pull-up: true 108 drive-strength: true 109 input-enable: true 110 output-high: true 111 output-low: true 112 113 required: 114 - pins 115 116 additionalProperties: false 117 118examples: 119 - | 120 #include <dt-bindings/interrupt-controller/arm-gic.h> 121 122 pinctrl@1000000 { 123 compatible = "qcom,msm8909-tlmm"; 124 reg = <0x1000000 0x300000>; 125 interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; 126 gpio-controller; 127 #gpio-cells = <2>; 128 gpio-ranges = <&tlmm 0 0 117>; 129 interrupt-controller; 130 #interrupt-cells = <2>; 131 132 gpio-wo-subnode-state { 133 pins = "gpio1"; 134 function = "gpio"; 135 }; 136 137 uart-w-subnodes-state { 138 rx-pins { 139 pins = "gpio4"; 140 function = "blsp_uart1"; 141 bias-pull-up; 142 }; 143 144 tx-pins { 145 pins = "gpio5"; 146 function = "blsp_uart1"; 147 bias-disable; 148 }; 149 }; 150 }; 151... 152