1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: Qualcomm Technologies, Inc. IPQ6018 TLMM block 8 9maintainers: 10 - Bjorn Andersson <andersson@kernel.org> 11 12description: 13 Top Level Mode Multiplexer pin controller in Qualcomm IPQ6018 SoC. 14 15properties: 16 compatible: 17 const: qcom,ipq6018-pinctrl 18 19 reg: 20 maxItems: 1 21 22 interrupts: 23 maxItems: 1 24 25 interrupt-controller: true 26 "#interrupt-cells": true 27 gpio-controller: true 28 "#gpio-cells": true 29 gpio-ranges: true 30 31patternProperties: 32 "-state$": 33 oneOf: 34 - $ref: "#/$defs/qcom-ipq6018-tlmm-state" 35 - patternProperties: 36 "-pins$": 37 $ref: "#/$defs/qcom-ipq6018-tlmm-state" 38 additionalProperties: false 39 40$defs: 41 qcom-ipq6018-tlmm-state: 42 description: 43 Pinctrl node's client devices use subnodes for desired pin configuration. 44 Client device subnodes use below standard properties. 45 $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state 46 47 properties: 48 pins: 49 description: 50 List of gpio pins affected by the properties specified in this 51 subnode. 52 items: 53 oneOf: 54 - pattern: "^gpio([1-9]|[1-7][0-9]|80)$" 55 - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, 56 sdc2_data, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2, 57 qdsd_data3 ] 58 minItems: 1 59 maxItems: 16 60 61 function: 62 description: 63 Specify the alternative function to be configured for the specified 64 pins. 65 enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char, 66 atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac, 67 atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0, 68 atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp0_i2c, blsp1_i2c, 69 blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp0_spi, blsp1_spi, 70 blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi, 71 blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi, 72 blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi, 73 blsp0_uart, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst, 74 cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0, 75 cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v, 76 dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass, 77 flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, 78 gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0, 79 gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2, 80 ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc, 81 nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s, 82 pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b, 83 pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a, 84 pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1, 85 qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0, 86 qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1, 87 qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, 88 qdss_tracedata_a, qdss_tracedata_b, qpic_pad, reset_n, sd_card, 89 sd_write, sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, 90 uim3, uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ] 91 92 bias-pull-down: true 93 bias-pull-up: true 94 bias-disable: true 95 drive-strength: true 96 output-high: true 97 output-low: true 98 99 required: 100 - pins 101 102 additionalProperties: false 103 104allOf: 105 - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# 106 107required: 108 - compatible 109 - reg 110 111additionalProperties: false 112 113examples: 114 - | 115 #include <dt-bindings/interrupt-controller/arm-gic.h> 116 tlmm: pinctrl@1000000 { 117 compatible = "qcom,ipq6018-pinctrl"; 118 reg = <0x01000000 0x300000>; 119 interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; 120 interrupt-controller; 121 #interrupt-cells = <2>; 122 gpio-controller; 123 #gpio-cells = <2>; 124 gpio-ranges = <&tlmm 0 0 80>; 125 126 serial3-state { 127 pins = "gpio44", "gpio45"; 128 function = "blsp2_uart"; 129 drive-strength = <8>; 130 bias-pull-down; 131 }; 132 }; 133