1TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs 2 3OMAP CONTROL PHY 4 5Required properties: 6 - compatible: Should be one of 7 "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4. 8 "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register 9 e.g. USB2_PHY on OMAP5. 10 "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control 11 e.g. USB3 PHY and SATA PHY on OMAP5. 12 "ti,control-phy-pcie" - for pcie to support external clock for pcie and to 13 set PCS delay value. 14 e.g. PCIE PHY in DRA7x 15 "ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on 16 DRA7 platform. 17 "ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on 18 AM437 platform. 19 - reg : register ranges as listed in the reg-names property 20 - reg-names: "otghs_control" for control-phy-otghs 21 "power", "pcie_pcs" and "control_sma" for control-phy-pcie 22 "power" for all other types 23 24omap_control_usb: omap-control-usb@4a002300 { 25 compatible = "ti,control-phy-otghs"; 26 reg = <0x4a00233c 0x4>; 27 reg-names = "otghs_control"; 28}; 29 30OMAP USB2 PHY 31 32Required properties: 33 - compatible: Should be "ti,omap-usb2" 34 Should be "ti,dra7x-usb2" for the 1st instance of USB2 PHY on 35 DRA7x 36 Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY 37 in DRA7x 38 - reg : Address and length of the register set for the device. 39 - #phy-cells: determine the number of cells that should be given in the 40 phandle while referencing this phy. 41 - clocks: a list of phandles and clock-specifier pairs, one for each entry in 42 clock-names. 43 - clock-names: should include: 44 * "wkupclk" - wakeup clock. 45 * "refclk" - reference clock (optional). 46 47Deprecated properties: 48 - ctrl-module : phandle of the control module used by PHY driver to power on 49 the PHY. 50 51Recommended properies: 52- syscon-phy-power : phandle/offset pair. Phandle to the system control 53 module and the register offset to power on/off the PHY. 54 55This is usually a subnode of ocp2scp to which it is connected. 56 57usb2phy@4a0ad080 { 58 compatible = "ti,omap-usb2"; 59 reg = <0x4a0ad080 0x58>; 60 ctrl-module = <&omap_control_usb>; 61 #phy-cells = <0>; 62 clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>; 63 clock-names = "wkupclk", "refclk"; 64}; 65 66TI PIPE3 PHY 67 68Required properties: 69 - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or 70 "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated. 71 - reg : Address and length of the register set for the device. 72 - reg-names: The names of the register addresses corresponding to the registers 73 filled in "reg". 74 - #phy-cells: determine the number of cells that should be given in the 75 phandle while referencing this phy. 76 - clocks: a list of phandles and clock-specifier pairs, one for each entry in 77 clock-names. 78 - clock-names: should include: 79 * "wkupclk" - wakeup clock. 80 * "sysclk" - system clock. 81 * "refclk" - reference clock. 82 * "dpll_ref" - external dpll ref clk 83 * "dpll_ref_m2" - external dpll ref clk 84 * "phy-div" - divider for apll 85 * "div-clk" - apll clock 86 87Optional properties: 88 - id: If there are multiple instance of the same type, in order to 89 differentiate between each instance "id" can be used (e.g., multi-lane PCIe 90 PHY). If "id" is not provided, it is set to default value of '1'. 91 - syscon-pllreset: Handle to system control region that contains the 92 CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0 93 register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy. 94 - syscon-pcs : phandle/offset pair. Phandle to the system control module and the 95 register offset to write the PCS delay value. 96 97Deprecated properties: 98 - ctrl-module : phandle of the control module used by PHY driver to power on 99 the PHY. 100 101Recommended properies: 102 - syscon-phy-power : phandle/offset pair. Phandle to the system control 103 module and the register offset to power on/off the PHY. 104 105This is usually a subnode of ocp2scp to which it is connected. 106 107usb3phy@4a084400 { 108 compatible = "ti,phy-usb3"; 109 reg = <0x4a084400 0x80>, 110 <0x4a084800 0x64>, 111 <0x4a084c00 0x40>; 112 reg-names = "phy_rx", "phy_tx", "pll_ctrl"; 113 ctrl-module = <&omap_control_usb>; 114 #phy-cells = <0>; 115 clocks = <&usb_phy_cm_clk32k>, 116 <&sys_clkin>, 117 <&usb_otg_ss_refclk960m>; 118 clock-names = "wkupclk", 119 "sysclk", 120 "refclk"; 121}; 122 123sata_phy: phy@4a096000 { 124 compatible = "ti,phy-pipe3-sata"; 125 reg = <0x4A096000 0x80>, /* phy_rx */ 126 <0x4A096400 0x64>, /* phy_tx */ 127 <0x4A096800 0x40>; /* pll_ctrl */ 128 reg-names = "phy_rx", "phy_tx", "pll_ctrl"; 129 ctrl-module = <&omap_control_sata>; 130 clocks = <&sys_clkin1>, <&sata_ref_clk>; 131 clock-names = "sysclk", "refclk"; 132 syscon-pllreset = <&scm_conf 0x3fc>; 133 #phy-cells = <0>; 134}; 135