1TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs 2 3OMAP CONTROL PHY 4 5Required properties: 6 - compatible: Should be one of 7 "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4. 8 "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register 9 e.g. USB2_PHY on OMAP5. 10 "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control 11 e.g. USB3 PHY and SATA PHY on OMAP5. 12 "ti,control-phy-pcie" - for pcie to support external clock for pcie and to 13 set PCS delay value. 14 e.g. PCIE PHY in DRA7x 15 "ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on 16 DRA7 platform. 17 "ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on 18 AM437 platform. 19 - reg : register ranges as listed in the reg-names property 20 - reg-names: "otghs_control" for control-phy-otghs 21 "power", "pcie_pcs" and "control_sma" for control-phy-pcie 22 "power" for all other types 23 24omap_control_usb: omap-control-usb@4a002300 { 25 compatible = "ti,control-phy-otghs"; 26 reg = <0x4a00233c 0x4>; 27 reg-names = "otghs_control"; 28}; 29 30TI PIPE3 PHY 31 32Required properties: 33 - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or 34 "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated. 35 - reg : Address and length of the register set for the device. 36 - reg-names: The names of the register addresses corresponding to the registers 37 filled in "reg". 38 - #phy-cells: determine the number of cells that should be given in the 39 phandle while referencing this phy. 40 - clocks: a list of phandles and clock-specifier pairs, one for each entry in 41 clock-names. 42 - clock-names: should include: 43 * "wkupclk" - wakeup clock. 44 * "sysclk" - system clock. 45 * "refclk" - reference clock. 46 * "dpll_ref" - external dpll ref clk 47 * "dpll_ref_m2" - external dpll ref clk 48 * "phy-div" - divider for apll 49 * "div-clk" - apll clock 50 51Optional properties: 52 - id: If there are multiple instance of the same type, in order to 53 differentiate between each instance "id" can be used (e.g., multi-lane PCIe 54 PHY). If "id" is not provided, it is set to default value of '1'. 55 - syscon-pllreset: Handle to system control region that contains the 56 CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0 57 register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy. 58 - syscon-pcs : phandle/offset pair. Phandle to the system control module and the 59 register offset to write the PCS delay value. 60 61Deprecated properties: 62 - ctrl-module : phandle of the control module used by PHY driver to power on 63 the PHY. 64 65Recommended properies: 66 - syscon-phy-power : phandle/offset pair. Phandle to the system control 67 module and the register offset to power on/off the PHY. 68 69This is usually a subnode of ocp2scp to which it is connected. 70 71usb3phy@4a084400 { 72 compatible = "ti,phy-usb3"; 73 reg = <0x4a084400 0x80>, 74 <0x4a084800 0x64>, 75 <0x4a084c00 0x40>; 76 reg-names = "phy_rx", "phy_tx", "pll_ctrl"; 77 ctrl-module = <&omap_control_usb>; 78 #phy-cells = <0>; 79 clocks = <&usb_phy_cm_clk32k>, 80 <&sys_clkin>, 81 <&usb_otg_ss_refclk960m>; 82 clock-names = "wkupclk", 83 "sysclk", 84 "refclk"; 85}; 86 87sata_phy: phy@4a096000 { 88 compatible = "ti,phy-pipe3-sata"; 89 reg = <0x4A096000 0x80>, /* phy_rx */ 90 <0x4A096400 0x64>, /* phy_tx */ 91 <0x4A096800 0x40>; /* pll_ctrl */ 92 reg-names = "phy_rx", "phy_tx", "pll_ctrl"; 93 ctrl-module = <&omap_control_sata>; 94 clocks = <&sys_clkin1>, <&sata_ref_clk>; 95 clock-names = "sysclk", "refclk"; 96 syscon-pllreset = <&scm_conf 0x3fc>; 97 #phy-cells = <0>; 98}; 99