1* Mediatek/Ralink RT3883 PCI controller 2 31) Main node 4 5 Required properties: 6 7 - compatible: must be "ralink,rt3883-pci" 8 9 - reg: specifies the physical base address of the controller and 10 the length of the memory mapped region. 11 12 - #address-cells: specifies the number of cells needed to encode an 13 address. The value must be 1. 14 15 - #size-cells: specifies the number of cells used to represent the size 16 of an address. The value must be 1. 17 18 - ranges: specifies the translation between child address space and parent 19 address space 20 21 Optional properties: 22 23 - status: indicates the operational status of the device. 24 Value must be either "disabled" or "okay". 25 262) Child nodes 27 28 The main node must have two child nodes which describes the built-in 29 interrupt controller and the PCI host bridge. 30 31 a) Interrupt controller: 32 33 Required properties: 34 35 - interrupt-controller: identifies the node as an interrupt controller 36 37 - #address-cells: specifies the number of cells needed to encode an 38 address. The value must be 0. As such, 'interrupt-map' nodes do not 39 have to specify a parent unit address. 40 41 - #interrupt-cells: specifies the number of cells needed to encode an 42 interrupt source. The value must be 1. 43 44 - interrupt-parent: the phandle for the interrupt controller that 45 services interrupts for this device. 46 47 - interrupts: specifies the interrupt source of the parent interrupt 48 controller. The format of the interrupt specifier depends on the 49 parent interrupt controller. 50 51 b) PCI host bridge: 52 53 Required properties: 54 55 - #address-cells: specifies the number of cells needed to encode an 56 address. The value must be 0. 57 58 - #size-cells: specifies the number of cells used to represent the size 59 of an address. The value must be 2. 60 61 - #interrupt-cells: specifies the number of cells needed to encode an 62 interrupt source. The value must be 1. 63 64 - device_type: must be "pci" 65 66 - bus-range: PCI bus numbers covered 67 68 - ranges: specifies the ranges for the PCI memory and I/O regions 69 70 - interrupt-map-mask, 71 - interrupt-map: standard PCI properties to define the mapping of the 72 PCI interface to interrupt numbers. 73 74 The PCI host bridge node might have additional sub-nodes representing 75 the onboard PCI devices/PCI slots. Each such sub-node must have the 76 following mandatory properties: 77 78 - reg: used only for interrupt mapping, so only the first four bytes 79 are used to refer to the correct bus number and device number. 80 81 - device_type: must be "pci" 82 83 If a given sub-node represents a PCI bridge it must have following 84 mandatory properties as well: 85 86 - #address-cells: must be set to <3> 87 88 - #size-cells: must set to <2> 89 90 - #interrupt-cells: must be set to <1> 91 92 - interrupt-map-mask, 93 - interrupt-map: standard PCI properties to define the mapping of the 94 PCI interface to interrupt numbers. 95 96 Besides the required properties the sub-nodes may have these optional 97 properties: 98 99 - status: indicates the operational status of the sub-node. 100 Value must be either "disabled" or "okay". 101 1023) Example: 103 104 a) SoC specific dtsi file: 105 106 pci@10140000 { 107 compatible = "ralink,rt3883-pci"; 108 reg = <0x10140000 0x20000>; 109 #address-cells = <1>; 110 #size-cells = <1>; 111 ranges; /* direct mapping */ 112 113 status = "disabled"; 114 115 pciintc: interrupt-controller { 116 interrupt-controller; 117 #address-cells = <0>; 118 #interrupt-cells = <1>; 119 120 interrupt-parent = <&cpuintc>; 121 interrupts = <4>; 122 }; 123 124 host-bridge { 125 #address-cells = <3>; 126 #size-cells = <2>; 127 #interrupt-cells = <1>; 128 129 device_type = "pci"; 130 131 bus-range = <0 255>; 132 ranges = < 133 0x02000000 0 0x00000000 0x20000000 0 0x10000000 /* pci memory */ 134 0x01000000 0 0x00000000 0x10160000 0 0x00010000 /* io space */ 135 >; 136 137 interrupt-map-mask = <0xf800 0 0 7>; 138 interrupt-map = < 139 /* IDSEL 17 */ 140 0x8800 0 0 1 &pciintc 18 141 0x8800 0 0 2 &pciintc 18 142 0x8800 0 0 3 &pciintc 18 143 0x8800 0 0 4 &pciintc 18 144 /* IDSEL 18 */ 145 0x9000 0 0 1 &pciintc 19 146 0x9000 0 0 2 &pciintc 19 147 0x9000 0 0 3 &pciintc 19 148 0x9000 0 0 4 &pciintc 19 149 >; 150 151 pci-bridge@1 { 152 reg = <0x0800 0 0 0 0>; 153 device_type = "pci"; 154 #interrupt-cells = <1>; 155 #address-cells = <3>; 156 #size-cells = <2>; 157 158 interrupt-map-mask = <0x0 0 0 0>; 159 interrupt-map = <0x0 0 0 0 &pciintc 20>; 160 161 status = "disabled"; 162 }; 163 164 pci-slot@17 { 165 reg = <0x8800 0 0 0 0>; 166 device_type = "pci"; 167 168 status = "disabled"; 169 }; 170 171 pci-slot@18 { 172 reg = <0x9000 0 0 0 0>; 173 device_type = "pci"; 174 175 status = "disabled"; 176 }; 177 }; 178 }; 179 180 b) Board specific dts file: 181 182 pci@10140000 { 183 status = "okay"; 184 185 host-bridge { 186 pci-bridge@1 { 187 status = "okay"; 188 }; 189 }; 190 }; 191