xref: /linux/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml (revision 8a4db021b9445dd019f1b4e9466c5812ddf9e63a)

# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pci/brcm,stb-pcie.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Brcmstb PCIe Host Controller

maintainers:
  - Jim Quinlan <james.quinlan@broadcom.com>

properties:
  compatible:
    items:
      - enum:
          - brcm,bcm2711-pcie # The Raspberry Pi 4
          - brcm,bcm4908-pcie
          - brcm,bcm7211-pcie # Broadcom STB version of RPi4
          - brcm,bcm7216-pcie # Broadcom 7216 Arm
          - brcm,bcm7278-pcie # Broadcom 7278 Arm
          - brcm,bcm7425-pcie # Broadcom 7425 MIPs
          - brcm,bcm7435-pcie # Broadcom 7435 MIPs
          - brcm,bcm7445-pcie # Broadcom 7445 Arm

  reg:
    maxItems: 1

  interrupts:
    minItems: 1
    items:
      - description: PCIe host controller
      - description: builtin MSI controller

  interrupt-names:
    minItems: 1
    items:
      - const: pcie
      - const: msi

  ranges:
    minItems: 1
    maxItems: 4

  dma-ranges:
    minItems: 1
    maxItems: 6

  clocks:
    maxItems: 1

  clock-names:
    items:
      - const: sw_pcie

  msi-controller:
    description: Identifies the node as an MSI controller.

  msi-parent:
    description: MSI controller the device is capable of using.

  brcm,enable-ssc:
    description: Indicates usage of spread-spectrum clocking.
    type: boolean

  aspm-no-l0s: true

  brcm,clkreq-mode:
    description: A string that determines the operating
      clkreq mode of the PCIe RC HW with respect to controlling the refclk
      signal.  There are three different modes -- "safe", which drives the
      refclk signal unconditionally and will work for all devices but does
      not provide any power savings; "no-l1ss" -- which provides Clock
      Power Management, L0s, and L1, but cannot provide L1 substate (L1SS)
      power savings. If the downstream device connected to the RC is L1SS
      capable AND the OS enables L1SS, all PCIe traffic may abruptly halt,
      potentially hanging the system; "default" -- which provides L0s, L1,
      and L1SS, but not compliant to provide Clock Power Management;
      specifically, may not be able to meet the T_CLRon max timing of 400ns
      as specified in "Dynamic Clock Control", section 3.2.5.2.2 PCI
      Express Mini CEM 2.1 specification.  This situation is atypical and
      should happen only with older devices.
    $ref: /schemas/types.yaml#/definitions/string
    enum: [ safe, no-l1ss, default ]

  brcm,scb-sizes:
    description: u64 giving the 64bit PCIe memory
      viewport size of a memory controller.  There may be up to
      three controllers, and each size must be a power of two
      with a size greater or equal to the amount of memory the
      controller supports.  Note that each memory controller
      may have two component regions -- base and extended -- so
      this information cannot be deduced from the dma-ranges.
    $ref: /schemas/types.yaml#/definitions/uint64-array
    items:
      minItems: 1
      maxItems: 3

required:
  - compatible
  - reg
  - ranges
  - dma-ranges
  - "#interrupt-cells"
  - interrupts
  - interrupt-names
  - interrupt-map-mask
  - interrupt-map
  - msi-controller

allOf:
  - $ref: /schemas/pci/pci-host-bridge.yaml#
  - $ref: /schemas/interrupt-controller/msi-controller.yaml#
  - if:
      properties:
        compatible:
          contains:
            const: brcm,bcm4908-pcie
    then:
      properties:
        resets:
          items:
            - description: reset controller handling the PERST# signal

        reset-names:
          items:
            - const: perst

      required:
        - resets
        - reset-names
  - if:
      properties:
        compatible:
          contains:
            const: brcm,bcm7216-pcie
    then:
      properties:
        resets:
          items:
            - description: phandle pointing to the RESCAL reset controller

        reset-names:
          items:
            - const: rescal

      required:
        - resets
        - reset-names

unevaluatedProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/irq.h>
    #include <dt-bindings/interrupt-controller/arm-gic.h>

    scb {
            #address-cells = <2>;
            #size-cells = <1>;
            pcie0: pcie@7d500000 {
                    compatible = "brcm,bcm2711-pcie";
                    reg = <0x0 0x7d500000 0x9310>;
                    device_type = "pci";
                    #address-cells = <3>;
                    #size-cells = <2>;
                    #interrupt-cells = <1>;
                    interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
                                 <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
                    interrupt-names = "pcie", "msi";
                    interrupt-map-mask = <0x0 0x0 0x0 0x7>;
                    interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH
                                     0 0 0 2 &gicv2 GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH
                                     0 0 0 3 &gicv2 GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH
                                     0 0 0 4 &gicv2 GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;

                    msi-parent = <&pcie0>;
                    msi-controller;
                    ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000 0x0 0x04000000>;
                    dma-ranges = <0x42000000 0x1 0x00000000 0x0 0x40000000 0x0 0x80000000>,
                                 <0x42000000 0x1 0x80000000 0x3 0x00000000 0x0 0x80000000>;
                    brcm,enable-ssc;
                    brcm,scb-sizes =  <0x0000000080000000 0x0000000080000000>;

                    /* PCIe bridge, Root Port */
                    pci@0,0 {
                            #address-cells = <3>;
                            #size-cells = <2>;
                            reg = <0x0 0x0 0x0 0x0 0x0>;
                            compatible = "pciclass,0604";
                            device_type = "pci";
                            vpcie3v3-supply = <&vreg7>;
                            ranges;

                            /* PCIe endpoint */
                            pci-ep@0,0 {
                                    assigned-addresses =
                                        <0x82010000 0x0 0xf8000000 0x6 0x00000000 0x0 0x2000>;
                                    reg = <0x0 0x0 0x0 0x0 0x0>;
                                    compatible = "pci14e4,1688";
                            };
                    };
            };
    };