1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/net/sff,sfp.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP) 8 Transceiver 9 10maintainers: 11 - Russell King <linux@armlinux.org.uk> 12 13properties: 14 compatible: 15 enum: 16 - sff,sfp # for SFP modules 17 - sff,sff # for soldered down SFF modules 18 19 i2c-bus: 20 $ref: /schemas/types.yaml#/definitions/phandle 21 description: 22 phandle of an I2C bus controller for the SFP two wire serial 23 24 maximum-power-milliwatt: 25 minimum: 1000 26 default: 1000 27 description: 28 Maximum module power consumption Specifies the maximum power consumption 29 allowable by a module in the slot, in milli-Watts. Presently, modules can 30 be up to 1W, 1.5W or 2W. 31 32 mod-def0-gpios: 33 maxItems: 1 34 description: 35 GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) module 36 presence input gpio signal, active (module absent) high. Must not be 37 present for SFF modules 38 39 los-gpios: 40 maxItems: 1 41 description: 42 GPIO phandle and a specifier of the Receiver Loss of Signal Indication 43 input gpio signal, active (signal lost) high 44 45 tx-fault-gpios: 46 maxItems: 1 47 description: 48 GPIO phandle and a specifier of the Module Transmitter Fault input gpio 49 signal, active (fault condition) high 50 51 tx-disable-gpios: 52 maxItems: 1 53 description: 54 GPIO phandle and a specifier of the Transmitter Disable output gpio 55 signal, active (Tx disable) high 56 57 rate-select0-gpios: 58 maxItems: 1 59 description: 60 GPIO phandle and a specifier of the Rx Signaling Rate Select (AKA RS0) 61 output gpio signal, low - low Rx rate, high - high Rx rate Must not be 62 present for SFF modules 63 64 rate-select1-gpios: 65 maxItems: 1 66 description: 67 GPIO phandle and a specifier of the Tx Signaling Rate Select (AKA RS1) 68 output gpio signal (SFP+ only), low - low Tx rate, high - high Tx rate. Must 69 not be present for SFF modules 70 71allOf: 72 - if: 73 properties: 74 compatible: 75 contains: 76 const: sff,sff 77 then: 78 properties: 79 mod-def0-gpios: false 80 rate-select0-gpios: false 81 rate-select1-gpios: false 82 83required: 84 - compatible 85 - i2c-bus 86 87additionalProperties: false 88 89examples: 90 - | # Direct serdes to SFP connection 91 #include <dt-bindings/gpio/gpio.h> 92 93 sfp1: sfp { 94 compatible = "sff,sfp"; 95 i2c-bus = <&sfp_1g_i2c>; 96 los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>; 97 mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>; 98 maximum-power-milliwatt = <1000>; 99 pinctrl-names = "default"; 100 pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>; 101 tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>; 102 tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>; 103 }; 104 105 ethernet { 106 phy-names = "comphy"; 107 phys = <&cps_comphy5 0>; 108 sfp = <&sfp1>; 109 }; 110 111 - | # Serdes to PHY to SFP connection 112 #include <dt-bindings/gpio/gpio.h> 113 #include <dt-bindings/interrupt-controller/arm-gic.h> 114 115 sfp2: sfp { 116 compatible = "sff,sfp"; 117 i2c-bus = <&sfp_i2c>; 118 los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>; 119 mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>; 120 pinctrl-names = "default"; 121 pinctrl-0 = <&cps_sfpp0_pins>; 122 tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>; 123 tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>; 124 }; 125 126 mdio { 127 #address-cells = <1>; 128 #size-cells = <0>; 129 130 phy: ethernet-phy@0 { 131 compatible = "ethernet-phy-ieee802.3-c45"; 132 pinctrl-names = "default"; 133 pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>; 134 reg = <0>; 135 interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>; 136 sfp = <&sfp2>; 137 }; 138 }; 139 140 ethernet { 141 phy = <&phy>; 142 phy-mode = "10gbase-kr"; 143 }; 144