xref: /linux/Documentation/devicetree/bindings/net/qcom,qca807x.yaml (revision c532de5a67a70f8533d495f8f2aaa9a0491c3ad0) 
1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/net/qcom,qca807x.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Qualcomm QCA807x Ethernet PHY
8
9maintainers:
10  - Christian Marangi <ansuelsmth@gmail.com>
11  - Robert Marko <robert.marko@sartura.hr>
12
13description: |
14  Qualcomm QCA8072/5 Ethernet PHY is PHY package of 2 or 5
15  IEEE 802.3 clause 22 compliant 10BASE-Te, 100BASE-TX and
16  1000BASE-T PHY-s.
17
18  They feature 2 SerDes, one for PSGMII or QSGMII connection with
19  MAC, while second one is SGMII for connection to MAC or fiber.
20
21  Both models have a combo port that supports 1000BASE-X and
22  100BASE-FX fiber.
23
24  Each PHY inside of QCA807x series has 4 digitally controlled
25  output only pins that natively drive LED-s for up to 2 attached
26  LEDs. Some vendor also use these 4 output for GPIO usage without
27  attaching LEDs.
28
29  Note that output pins can be set to drive LEDs OR GPIO, mixed
30  definition are not accepted.
31
32$ref: ethernet-phy-package.yaml#
33
34properties:
35  compatible:
36    enum:
37      - qcom,qca8072-package
38      - qcom,qca8075-package
39
40  qcom,package-mode:
41    description: |
42      PHY package can be configured in 3 mode following this table:
43
44                    First Serdes mode       Second Serdes mode
45      Option 1      PSGMII for copper       Disabled
46                    ports 0-4
47      Option 2      PSGMII for copper       1000BASE-X / 100BASE-FX
48                    ports 0-4
49      Option 3      QSGMII for copper       SGMII for
50                    ports 0-3               copper port 4
51
52      PSGMII mode (option 1 or 2) is configured dynamically based on
53      the presence of a connected SFP device.
54    $ref: /schemas/types.yaml#/definitions/string
55    enum:
56      - qsgmii
57      - psgmii
58    default: psgmii
59
60  qcom,tx-drive-strength-milliwatt:
61    description: set the TX Amplifier value in mv.
62    $ref: /schemas/types.yaml#/definitions/uint32
63    enum: [140, 160, 180, 200, 220,
64           240, 260, 280, 300, 320,
65           400, 500, 600]
66    default: 600
67
68patternProperties:
69  ^ethernet-phy@[a-f0-9]+$:
70    $ref: ethernet-phy.yaml#
71
72    properties:
73      qcom,dac-full-amplitude:
74        description:
75          Set Analog MDI driver amplitude to FULL.
76
77          With this not defined, amplitude is set to DSP.
78          (amplitude is adjusted based on cable length)
79
80          With this enabled and qcom,dac-full-bias-current
81          and qcom,dac-disable-bias-current-tweak disabled,
82          bias current is half.
83        type: boolean
84
85      qcom,dac-full-bias-current:
86        description:
87          Set Analog MDI driver bias current to FULL.
88
89          With this not defined, bias current is set to DSP.
90          (bias current is adjusted based on cable length)
91
92          Actual bias current might be different with
93          qcom,dac-disable-bias-current-tweak disabled.
94        type: boolean
95
96      qcom,dac-disable-bias-current-tweak:
97        description: |
98          Set Analog MDI driver bias current to disable tweak
99          to bias current.
100
101          With this not defined, bias current tweak are enabled
102          by default.
103
104          With this enabled the following tweak are NOT applied:
105          - With both FULL amplitude and FULL bias current: bias current
106            is set to half.
107          - With only DSP amplitude: bias current is set to half and
108            is set to 1/4 with cable < 10m.
109          - With DSP bias current (included both DSP amplitude and
110            DSP bias current): bias current is half the detected current
111            with cable < 10m.
112        type: boolean
113
114      gpio-controller: true
115
116      '#gpio-cells':
117        const: 2
118
119    if:
120      required:
121        - gpio-controller
122    then:
123      properties:
124        leds: false
125
126    unevaluatedProperties: false
127
128required:
129  - compatible
130
131unevaluatedProperties: false
132
133examples:
134  - |
135    #include <dt-bindings/leds/common.h>
136
137    mdio {
138        #address-cells = <1>;
139        #size-cells = <0>;
140
141        ethernet-phy-package@0 {
142            #address-cells = <1>;
143            #size-cells = <0>;
144            compatible = "qcom,qca8075-package";
145            reg = <0>;
146
147            qcom,package-mode = "qsgmii";
148
149            ethernet-phy@0 {
150                reg = <0>;
151
152                leds {
153                    #address-cells = <1>;
154                    #size-cells = <0>;
155
156                    led@0 {
157                        reg = <0>;
158                        color = <LED_COLOR_ID_GREEN>;
159                        function = LED_FUNCTION_LAN;
160                        default-state = "keep";
161                    };
162                };
163            };
164
165            ethernet-phy@1 {
166                reg = <1>;
167            };
168
169            ethernet-phy@2 {
170                reg = <2>;
171
172                gpio-controller;
173                #gpio-cells = <2>;
174            };
175
176            ethernet-phy@3 {
177                reg = <3>;
178            };
179
180            ethernet-phy@4 {
181                reg = <4>;
182            };
183        };
184    };
185