xref: /linux/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt (revision 48dea9a700c8728cc31a1dd44588b97578de86ee) 
1Hisilicon hip04 Ethernet Controller
2
3* Ethernet controller node
4
5Required properties:
6- compatible: should be "hisilicon,hip04-mac".
7- reg: address and length of the register set for the device.
8- interrupts: interrupt for the device.
9- port-handle: <phandle port channel>
10	phandle, specifies a reference to the syscon ppe node
11	port, port number connected to the controller
12	channel, recv channel start from channel * number (RX_DESC_NUM)
13	group, field in the pkg desc, in general, it is the same as the port.
14- phy-mode: see ethernet.txt [1].
15
16Optional properties:
17- phy-handle: see ethernet.txt [1].
18
19[1] Documentation/devicetree/bindings/net/ethernet.txt
20
21
22* Ethernet ppe node:
23Control rx & tx fifos of all ethernet controllers.
24Have 2048 recv channels shared by all ethernet controllers, only if no overlap.
25Each controller's recv channel start from channel * number (RX_DESC_NUM).
26
27Required properties:
28- compatible: "hisilicon,hip04-ppe", "syscon".
29- reg: address and length of the register set for the device.
30
31
32* MDIO bus node:
33
34Required properties:
35
36- compatible: should be "hisilicon,mdio".
37- Inherits from MDIO bus node binding [2]
38[2] Documentation/devicetree/bindings/net/phy.txt
39
40Example:
41	mdio {
42		compatible = "hisilicon,mdio";
43		reg = <0x28f1000 0x1000>;
44		#address-cells = <1>;
45		#size-cells = <0>;
46
47		phy0: ethernet-phy@0 {
48			compatible = "ethernet-phy-ieee802.3-c22";
49			reg = <0>;
50			marvell,reg-init = <18 0x14 0 0x8001>;
51		};
52
53		phy1: ethernet-phy@1 {
54			compatible = "ethernet-phy-ieee802.3-c22";
55			reg = <1>;
56			marvell,reg-init = <18 0x14 0 0x8001>;
57		};
58	};
59
60	ppe: ppe@28c0000 {
61		compatible = "hisilicon,hip04-ppe", "syscon";
62		reg = <0x28c0000 0x10000>;
63	};
64
65	fe: ethernet@28b0000 {
66		compatible = "hisilicon,hip04-mac";
67		reg = <0x28b0000 0x10000>;
68		interrupts = <0 413 4>;
69		phy-mode = "mii";
70		port-handle = <&ppe 31 0 31>;
71	};
72
73	ge0: ethernet@2800000 {
74		compatible = "hisilicon,hip04-mac";
75		reg = <0x2800000 0x10000>;
76		interrupts = <0 402 4>;
77		phy-mode = "sgmii";
78		port-handle = <&ppe 0 1 0>;
79		phy-handle = <&phy0>;
80	};
81
82	ge8: ethernet@2880000 {
83		compatible = "hisilicon,hip04-mac";
84		reg = <0x2880000 0x10000>;
85		interrupts = <0 410 4>;
86		phy-mode = "sgmii";
87		port-handle = <&ppe 8 2 8>;
88		phy-handle = <&phy1>;
89	};
90