xref: /linux/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.yaml (revision c532de5a67a70f8533d495f8f2aaa9a0491c3ad0) 
1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/net/dsa/vitesse,vsc73xx.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Vitesse VSC73xx DSA Switches
8
9maintainers:
10  - Linus Walleij <linus.walleij@linaro.org>
11
12description:
13  The Vitesse DSA Switches were produced in the early-to-mid 2000s.
14
15  The Vitesse company has been acquired by Microsemi and Microsemi has
16  been acquired Microchip but the new owner retains this vendor branding.
17
18  The currently supported switch chips are
19  Vitesse VSC7385 SparX-G5 5+1-port Integrated Gigabit Ethernet Switch
20  Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch
21  Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch
22  Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch
23
24  This switch can use one of two different management interfaces.
25
26  If SPI interface is used, the device tree node is an SPI device so it must
27  reside inside a SPI bus device tree node, see spi/spi-bus.txt
28
29  When the chip is connected to a parallel memory bus and work in memory-mapped
30  I/O mode, a platform device is used to represent the vsc73xx. In this case it
31  must reside inside a platform bus device tree node.
32
33properties:
34  compatible:
35    enum:
36      - vitesse,vsc7385
37      - vitesse,vsc7388
38      - vitesse,vsc7395
39      - vitesse,vsc7398
40
41  reg:
42    maxItems: 1
43
44  gpio-controller: true
45  "#gpio-cells":
46    const: 2
47
48  reset-gpios:
49    description: GPIO to be used to reset the whole device
50    maxItems: 1
51
52allOf:
53  - $ref: dsa.yaml#/$defs/ethernet-ports
54
55patternProperties:
56  "^(ethernet-)?ports$":
57    additionalProperties: true
58    patternProperties:
59      "^(ethernet-)?port@6$":
60        allOf:
61          - if:
62              properties:
63                phy-mode:
64                  contains:
65                    enum:
66                      - rgmii
67            then:
68              properties:
69                rx-internal-delay-ps:
70                  $ref: "#/$defs/internal-delay-ps"
71                tx-internal-delay-ps:
72                  $ref: "#/$defs/internal-delay-ps"
73
74# This checks if reg is a chipselect so the device is on an SPI
75# bus, the if-clause will fail if reg is a tuple such as for a
76# platform device.
77if:
78  properties:
79    reg:
80      minimum: 0
81      maximum: 256
82then:
83  $ref: /schemas/spi/spi-peripheral-props.yaml#
84
85required:
86  - compatible
87  - reg
88
89$defs:
90  internal-delay-ps:
91    description:
92      Disable tunable delay lines using 0 ps, or enable them and select
93      the phase between 1400 ps and 2000 ps in increments of 300 ps.
94    default: 2000
95    enum:
96      [0, 1400, 1700, 2000]
97
98unevaluatedProperties: false
99
100examples:
101  - |
102    #include <dt-bindings/gpio/gpio.h>
103
104    spi {
105      #address-cells = <1>;
106      #size-cells = <0>;
107
108      ethernet-switch@0 {
109        compatible = "vitesse,vsc7395";
110        reg = <0>;
111        spi-max-frequency = <2500000>;
112        gpio-controller;
113        #gpio-cells = <2>;
114
115        ethernet-ports {
116          #address-cells = <1>;
117          #size-cells = <0>;
118
119          ethernet-port@0 {
120            reg = <0>;
121            label = "lan1";
122          };
123          ethernet-port@1 {
124            reg = <1>;
125            label = "lan2";
126          };
127          ethernet-port@2 {
128            reg = <2>;
129            label = "lan3";
130          };
131          ethernet-port@3 {
132            reg = <3>;
133            label = "lan4";
134          };
135          ethernet-port@6 {
136            reg = <6>;
137            ethernet = <&gmac1>;
138            phy-mode = "rgmii";
139            rx-internal-delay-ps = <0>;
140            tx-internal-delay-ps = <0>;
141            fixed-link {
142              speed = <1000>;
143              full-duplex;
144              pause;
145            };
146          };
147        };
148      };
149    };
150
151    bus {
152      #address-cells = <1>;
153      #size-cells = <1>;
154
155      ethernet-switch@10000000 {
156        compatible = "vitesse,vsc7385";
157        reg = <0x10000000 0x20000>;
158        reset-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
159
160        ethernet-ports {
161          #address-cells = <1>;
162          #size-cells = <0>;
163
164          ethernet-port@0 {
165            reg = <0>;
166            label = "lan1";
167          };
168          ethernet-port@1 {
169            reg = <1>;
170            label = "lan2";
171          };
172          ethernet-port@2 {
173            reg = <2>;
174            label = "lan3";
175          };
176          ethernet-port@3 {
177            reg = <3>;
178            label = "lan4";
179          };
180          ethernet-port@6 {
181            reg = <6>;
182            ethernet = <&enet0>;
183            rx-internal-delay-ps = <0>;
184            tx-internal-delay-ps = <0>;
185            phy-mode = "rgmii";
186            fixed-link {
187              speed = <1000>;
188              full-duplex;
189              pause;
190            };
191          };
192        };
193      };
194    };
195