1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/media/video-interfaces.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: Common Properties for Video Receiver and Transmitter Interface Endpoints 8 9maintainers: 10 - Sakari Ailus <sakari.ailus@linux.intel.com> 11 - Laurent Pinchart <laurent.pinchart@ideasonboard.com> 12 13description: | 14 Video data pipelines usually consist of external devices, e.g. camera sensors, 15 controlled over an I2C, SPI or UART bus, and SoC internal IP blocks, including 16 video DMA engines and video data processors. 17 18 SoC internal blocks are described by DT nodes, placed similarly to other SoC 19 blocks. External devices are represented as child nodes of their respective 20 bus controller nodes, e.g. I2C. 21 22 Data interfaces on all video devices are described by their child 'port' nodes. 23 Configuration of a port depends on other devices participating in the data 24 transfer and is described by 'endpoint' subnodes. 25 26 device { 27 ... 28 ports { 29 #address-cells = <1>; 30 #size-cells = <0>; 31 32 port@0 { 33 ... 34 endpoint@0 { ... }; 35 endpoint@1 { ... }; 36 }; 37 port@1 { ... }; 38 }; 39 }; 40 41 If a port can be configured to work with more than one remote device on the same 42 bus, an 'endpoint' child node must be provided for each of them. If more than 43 one port is present in a device node or there is more than one endpoint at a 44 port, or port node needs to be associated with a selected hardware interface, 45 a common scheme using '#address-cells', '#size-cells' and 'reg' properties is 46 used. 47 48 All 'port' nodes can be grouped under optional 'ports' node, which allows to 49 specify #address-cells, #size-cells properties independently for the 'port' 50 and 'endpoint' nodes and any child device nodes a device might have. 51 52 Two 'endpoint' nodes are linked with each other through their 'remote-endpoint' 53 phandles. An endpoint subnode of a device contains all properties needed for 54 configuration of this device for data exchange with other device. In most 55 cases properties at the peer 'endpoint' nodes will be identical, however they 56 might need to be different when there is any signal modifications on the bus 57 between two devices, e.g. there are logic signal inverters on the lines. 58 59 It is allowed for multiple endpoints at a port to be active simultaneously, 60 where supported by a device. For example, in case where a data interface of 61 a device is partitioned into multiple data busses, e.g. 16-bit input port 62 divided into two separate ITU-R BT.656 8-bit busses. In such case bus-width 63 and data-shift properties can be used to assign physical data lines to each 64 endpoint node (logical bus). 65 66 Documenting bindings for devices 67 -------------------------------- 68 69 All required and optional bindings the device supports shall be explicitly 70 documented in device DT binding documentation. This also includes port and 71 endpoint nodes for the device, including unit-addresses and reg properties 72 where relevant. 73 74allOf: 75 - $ref: /schemas/graph.yaml#/$defs/endpoint-base 76 77properties: 78 slave-mode: 79 type: boolean 80 description: 81 Indicates that the link is run in slave mode. The default when this 82 property is not specified is master mode. In the slave mode horizontal and 83 vertical synchronization signals are provided to the slave device (data 84 source) by the master device (data sink). In the master mode the data 85 source device is also the source of the synchronization signals. 86 87 bus-type: 88 $ref: /schemas/types.yaml#/definitions/uint32 89 enum: 90 - 1 # MIPI CSI-2 C-PHY 91 - 2 # MIPI CSI1 92 - 3 # CCP2 93 - 4 # MIPI CSI-2 D-PHY 94 - 5 # Parallel 95 - 6 # BT.656 96 - 7 # DPI 97 description: 98 Data bus type. 99 100 bus-width: 101 $ref: /schemas/types.yaml#/definitions/uint32 102 maximum: 64 103 description: 104 Number of data lines actively used, valid for the parallel busses. 105 106 data-shift: 107 $ref: /schemas/types.yaml#/definitions/uint32 108 maximum: 64 109 description: 110 On the parallel data busses, if bus-width is used to specify the number of 111 data lines, data-shift can be used to specify which data lines are used, 112 e.g. "bus-width=<8>; data-shift=<2>;" means, that lines 9:2 are used. 113 114 hsync-active: 115 $ref: /schemas/types.yaml#/definitions/uint32 116 enum: [ 0, 1 ] 117 description: 118 Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. 119 120 vsync-active: 121 $ref: /schemas/types.yaml#/definitions/uint32 122 enum: [ 0, 1 ] 123 description: 124 Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. Note, 125 that if HSYNC and VSYNC polarities are not specified, embedded 126 synchronization may be required, where supported. 127 128 data-active: 129 $ref: /schemas/types.yaml#/definitions/uint32 130 enum: [ 0, 1 ] 131 description: 132 Similar to HSYNC and VSYNC, specifies data line polarity. 133 134 data-enable-active: 135 $ref: /schemas/types.yaml#/definitions/uint32 136 enum: [ 0, 1 ] 137 description: 138 Similar to HSYNC and VSYNC, specifies the data enable signal polarity. 139 140 field-even-active: 141 $ref: /schemas/types.yaml#/definitions/uint32 142 enum: [ 0, 1 ] 143 description: 144 Field signal level during the even field data transmission. 145 146 pclk-sample: 147 $ref: /schemas/types.yaml#/definitions/uint32 148 enum: [ 0, 1, 2 ] 149 description: 150 Sample data on falling (0), rising (1) or both (2) edges of the pixel 151 clock signal. 152 153 sync-on-green-active: 154 $ref: /schemas/types.yaml#/definitions/uint32 155 enum: [ 0, 1 ] 156 description: 157 Active state of Sync-on-green (SoG) signal, 0/1 for LOW/HIGH respectively. 158 159 data-lanes: 160 $ref: /schemas/types.yaml#/definitions/uint32-array 161 minItems: 1 162 maxItems: 8 163 uniqueItems: true 164 items: 165 # Assume up to 9 physical lane indices 166 maximum: 8 167 description: 168 An array of physical data lane indexes. Position of an entry determines 169 the logical lane number, while the value of an entry indicates physical 170 lane, e.g. for 2-lane MIPI CSI-2 bus we could have "data-lanes = <1 2>;", 171 assuming the clock lane is on hardware lane 0. If the hardware does not 172 support lane reordering, monotonically incremented values shall be used 173 from 0 or 1 onwards, depending on whether or not there is also a clock 174 lane. This property is valid for serial busses only (e.g. MIPI CSI-2). 175 176 clock-lanes: 177 $ref: /schemas/types.yaml#/definitions/uint32 178 # Assume up to 9 physical lane indices 179 maximum: 8 180 description: 181 Physical clock lane index. Position of an entry determines the logical 182 lane number, while the value of an entry indicates physical lane, e.g. for 183 a MIPI CSI-2 bus we could have "clock-lanes = <0>;", which places the 184 clock lane on hardware lane 0. This property is valid for serial busses 185 only (e.g. MIPI CSI-2). 186 187 clock-noncontinuous: 188 type: boolean 189 description: 190 Allow MIPI CSI-2 non-continuous clock mode. 191 192 link-frequencies: 193 $ref: /schemas/types.yaml#/definitions/uint64-array 194 description: 195 Allowed data bus frequencies. For MIPI CSI-2, for instance, this is the 196 actual frequency of the bus, not bits per clock per lane value. An array 197 of 64-bit unsigned integers. 198 199 lane-polarities: 200 $ref: /schemas/types.yaml#/definitions/uint32-array 201 minItems: 1 202 maxItems: 9 203 items: 204 enum: [ 0, 1 ] 205 description: 206 An array of polarities of the lanes starting from the clock lane and 207 followed by the data lanes in the same order as in data-lanes. Valid 208 values are 0 (normal) and 1 (inverted). The length of the array should be 209 the combined length of data-lanes and clock-lanes properties. If the 210 lane-polarities property is omitted, the value must be interpreted as 0 211 (normal). This property is valid for serial busses only. 212 213 strobe: 214 $ref: /schemas/types.yaml#/definitions/uint32 215 enum: [ 0, 1 ] 216 description: 217 Whether the clock signal is used as clock (0) or strobe (1). Used with 218 CCP2, for instance. 219 220additionalProperties: true 221