xref: /linux/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml (revision f888bdf9823c85fe945c4eb3ba353f749dec3856) 
1# SPDX-License-Identifier: GPL-2.0
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/iio/adc/adi,ad7606.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Analog Devices AD7606 Simultaneous Sampling ADC
8
9maintainers:
10  - Beniamin Bia <beniamin.bia@analog.com>
11  - Stefan Popa <stefan.popa@analog.com>
12
13description: |
14  Analog Devices AD7606 Simultaneous Sampling ADC
15  https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf
16  https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf
17  https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf
18
19properties:
20  compatible:
21    enum:
22      - adi,ad7605-4
23      - adi,ad7606-8
24      - adi,ad7606-6
25      - adi,ad7606-4
26      - adi,ad7606b
27      - adi,ad7616
28
29  reg:
30    maxItems: 1
31
32  spi-cpha: true
33
34  spi-cpol: true
35
36  spi-max-frequency: true
37
38  avcc-supply: true
39
40  interrupts:
41    maxItems: 1
42
43  adi,conversion-start-gpios:
44    description:
45      Must be the device tree identifier of the CONVST pin.
46      This logic input is used to initiate conversions on the analog
47      input channels. As the line is active high, it should be marked
48      GPIO_ACTIVE_HIGH.
49    maxItems: 1
50
51  reset-gpios:
52    description:
53      Must be the device tree identifier of the RESET pin. If specified,
54      it will be asserted during driver probe. As the line is active high,
55      it should be marked GPIO_ACTIVE_HIGH.
56    maxItems: 1
57
58  standby-gpios:
59    description:
60      Must be the device tree identifier of the STBY pin. This pin is used
61      to place the AD7606 into one of two power-down modes, Standby mode or
62      Shutdown mode. As the line is active low, it should be marked
63      GPIO_ACTIVE_LOW.
64    maxItems: 1
65
66  adi,first-data-gpios:
67    description:
68      Must be the device tree identifier of the FRSTDATA pin.
69      The FRSTDATA output indicates when the first channel, V1, is
70      being read back on either the parallel, byte or serial interface.
71      As the line is active high, it should be marked GPIO_ACTIVE_HIGH.
72    maxItems: 1
73
74  adi,range-gpios:
75    description:
76      Must be the device tree identifier of the RANGE pin. The polarity on
77      this pin determines the input range of the analog input channels. If
78      this pin is tied to a logic high, the analog input range is ±10V for
79      all channels. If this pin is tied to a logic low, the analog input range
80      is ±5V for all channels. As the line is active high, it should be marked
81      GPIO_ACTIVE_HIGH.
82    maxItems: 1
83
84  adi,oversampling-ratio-gpios:
85    description:
86      Must be the device tree identifier of the over-sampling
87      mode pins. As the line is active high, it should be marked
88      GPIO_ACTIVE_HIGH.
89    maxItems: 3
90
91  adi,sw-mode:
92    description:
93      Software mode of operation, so far available only for ad7616 and ad7606b.
94      It is enabled when all three oversampling mode pins are connected to
95      high level. The device is configured by the corresponding registers. If the
96      adi,oversampling-ratio-gpios property is defined, then the driver will set the
97      oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired
98      to VDD.
99    type: boolean
100
101required:
102  - compatible
103  - reg
104  - spi-cpha
105  - avcc-supply
106  - interrupts
107  - adi,conversion-start-gpios
108
109additionalProperties: false
110
111examples:
112  - |
113    #include <dt-bindings/gpio/gpio.h>
114    #include <dt-bindings/interrupt-controller/irq.h>
115    spi0 {
116        #address-cells = <1>;
117        #size-cells = <0>;
118
119        adc@0 {
120                compatible = "adi,ad7606-8";
121                reg = <0>;
122                spi-max-frequency = <1000000>;
123                spi-cpol;
124                spi-cpha;
125
126                avcc-supply = <&adc_vref>;
127
128                interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
129                interrupt-parent = <&gpio>;
130
131                adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
132                reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
133                adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
134                adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>,
135                                               <&gpio 23 GPIO_ACTIVE_HIGH>,
136                                               <&gpio 26 GPIO_ACTIVE_HIGH>;
137                standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
138                adi,sw-mode;
139        };
140    };
141...
142