xref: /linux/Documentation/devicetree/bindings/dma/stm32/st,stm32-dma3.yaml (revision c532de5a67a70f8533d495f8f2aaa9a0491c3ad0) 
1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/dma/stm32/st,stm32-dma3.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: STMicroelectronics STM32 DMA3 Controller
8
9description: |
10  The STM32 DMA3 is a direct memory access controller with different features
11  depending on its hardware configuration.
12  It is either called LPDMA (Low Power), GPDMA (General Purpose) or HPDMA (High
13  Performance).
14  Its hardware configuration registers allow to dynamically expose its features.
15
16  GPDMA and HPDMA support 16 independent DMA channels, while only 4 for LPDMA.
17  GPDMA and HPDMA support 256 DMA requests from peripherals, 8 for LPDMA.
18
19  Bindings are generic for these 3 STM32 DMA3 configurations.
20
21  DMA clients connected to the STM32 DMA3 controller must use the format
22  described in "#dma-cells" property description below, using a three-cell
23  specifier for each channel.
24
25maintainers:
26  - Amelie Delaunay <amelie.delaunay@foss.st.com>
27
28allOf:
29  - $ref: /schemas/dma/dma-controller.yaml#
30
31properties:
32  compatible:
33    const: st,stm32mp25-dma3
34
35  reg:
36    maxItems: 1
37
38  interrupts:
39    minItems: 4
40    maxItems: 16
41    description:
42      Should contain all of the per-channel DMA interrupts in ascending order
43      with respect to the DMA channel index.
44
45  clocks:
46    maxItems: 1
47
48  resets:
49    maxItems: 1
50
51  power-domains:
52    maxItems: 1
53
54  "#dma-cells":
55    const: 3
56    description: |
57      Specifies the number of cells needed to provide DMA controller specific
58      information.
59      The first cell is the request line number.
60      The second cell is a 32-bit mask specifying the DMA channel requirements:
61        -bit 0-1: The priority level
62          0x0: low priority, low weight
63          0x1: low priority, mid weight
64          0x2: low priority, high weight
65          0x3: high priority
66        -bit 4-7: The FIFO requirement for queuing source/destination transfers
67          0x0: no FIFO requirement/any channel can fit
68          0x2: FIFO of 8 bytes (2^2+1)
69          0x4: FIFO of 32 bytes (2^4+1)
70          0x6: FIFO of 128 bytes (2^6+1)
71          0x7: FIFO of 256 bytes (2^7+1)
72      The third cell is a 32-bit mask specifying the DMA transfer requirements:
73        -bit 0: The source incrementing burst
74          0x0: fixed burst
75          0x1: contiguously incremented burst
76        -bit 1: The source allocated port
77          0x0: port 0 is allocated to the source transfer
78          0x1: port 1 is allocated to the source transfer
79        -bit 4: The destination incrementing burst
80          0x0: fixed burst
81          0x1: contiguously incremented burst
82        -bit 5: The destination allocated port
83          0x0: port 0 is allocated to the destination transfer
84          0x1: port 1 is allocated to the destination transfer
85        -bit 8: The type of hardware request
86          0x0: burst
87          0x1: block
88        -bit 9: The control mode
89          0x0: DMA controller control mode
90          0x1: peripheral control mode
91        -bit 12-13: The transfer complete event mode
92          0x0: at block level, transfer complete event is generated at the end
93               of a block
94          0x2: at LLI level, the transfer complete event is generated at the end
95               of the LLI transfer
96               including the update of the LLI if any
97          0x3: at channel level, the transfer complete event is generated at the
98               end of the last LLI
99
100required:
101  - compatible
102  - reg
103  - interrupts
104  - clocks
105  - "#dma-cells"
106
107unevaluatedProperties: false
108
109examples:
110  - |
111    #include <dt-bindings/interrupt-controller/arm-gic.h>
112    #include <dt-bindings/clock/st,stm32mp25-rcc.h>
113    dma-controller@40400000 {
114      compatible = "st,stm32mp25-dma3";
115      reg = <0x40400000 0x1000>;
116      interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
117                   <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
118                   <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
119                   <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
120                   <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
121                   <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
122                   <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
123                   <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
124                   <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
125                   <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
126                   <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
127                   <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
128                   <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
129                   <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
130                   <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
131                   <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
132      clocks = <&rcc CK_BUS_HPDMA1>;
133      #dma-cells = <3>;
134    };
135...
136