xref: /linux/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt (revision 24bce201d79807b668bf9d9e0aca801c5c0d5f78) 
1Freescale i.MX DRM master device
2================================
3
4The freescale i.MX DRM master device is a virtual device needed to list all
5IPU or other display interface nodes that comprise the graphics subsystem.
6
7Required properties:
8- compatible: Should be "fsl,imx-display-subsystem"
9- ports: Should contain a list of phandles pointing to display interface ports
10  of IPU devices
11
12example:
13
14display-subsystem {
15	compatible = "fsl,imx-display-subsystem";
16	ports = <&ipu_di0>;
17};
18
19
20Freescale i.MX IPUv3
21====================
22
23Required properties:
24- compatible: Should be "fsl,<chip>-ipu" where <chip> is one of
25  - imx51
26  - imx53
27  - imx6q
28  - imx6qp
29- reg: should be register base and length as documented in the
30  datasheet
31- interrupts: Should contain sync interrupt and error interrupt,
32  in this order.
33- resets: phandle pointing to the system reset controller and
34          reset line index, see reset/fsl,imx-src.txt for details
35Additional required properties for fsl,imx6qp-ipu:
36- fsl,prg: phandle to prg node associated with this IPU instance
37Optional properties:
38- port@[0-3]: Port nodes with endpoint definitions as defined in
39  Documentation/devicetree/bindings/media/video-interfaces.txt.
40  Ports 0 and 1 should correspond to CSI0 and CSI1,
41  ports 2 and 3 should correspond to DI0 and DI1, respectively.
42
43example:
44
45ipu: ipu@18000000 {
46	#address-cells = <1>;
47	#size-cells = <0>;
48	compatible = "fsl,imx53-ipu";
49	reg = <0x18000000 0x080000000>;
50	interrupts = <11 10>;
51	resets = <&src 2>;
52
53	ipu_di0: port@2 {
54		reg = <2>;
55
56		ipu_di0_disp0: endpoint {
57			remote-endpoint = <&display_in>;
58		};
59	};
60};
61
62Freescale i.MX PRE (Prefetch Resolve Engine)
63============================================
64
65Required properties:
66- compatible: should be "fsl,imx6qp-pre"
67- reg: should be register base and length as documented in the
68  datasheet
69- clocks : phandle to the PRE axi clock input, as described
70  in Documentation/devicetree/bindings/clock/clock-bindings.txt and
71  Documentation/devicetree/bindings/clock/imx6q-clock.yaml.
72- clock-names: should be "axi"
73- interrupts: should contain the PRE interrupt
74- fsl,iram: phandle pointing to the mmio-sram device node, that should be
75  used for the PRE SRAM double buffer.
76
77example:
78
79pre@21c8000 {
80	compatible = "fsl,imx6qp-pre";
81	reg = <0x021c8000 0x1000>;
82	interrupts = <GIC_SPI 90 IRQ_TYPE_EDGE_RISING>;
83	clocks = <&clks IMX6QDL_CLK_PRE0>;
84	clock-names = "axi";
85	fsl,iram = <&ocram2>;
86};
87
88Freescale i.MX PRG (Prefetch Resolve Gasket)
89============================================
90
91Required properties:
92- compatible: should be "fsl,imx6qp-prg"
93- reg: should be register base and length as documented in the
94  datasheet
95- clocks : phandles to the PRG ipg and axi clock inputs, as described
96  in Documentation/devicetree/bindings/clock/clock-bindings.txt and
97  Documentation/devicetree/bindings/clock/imx6q-clock.yaml.
98- clock-names: should be "ipg" and "axi"
99- fsl,pres: phandles to the PRE units attached to this PRG, with the fixed
100  PRE as the first entry and the muxable PREs following.
101
102example:
103
104prg@21cc000 {
105	compatible = "fsl,imx6qp-prg";
106	reg = <0x021cc000 0x1000>;
107	clocks = <&clks IMX6QDL_CLK_PRG0_APB>,
108		 <&clks IMX6QDL_CLK_PRG0_AXI>;
109	clock-names = "ipg", "axi";
110	fsl,pres = <&pre1>, <&pre2>, <&pre3>;
111};
112
113Parallel display support
114========================
115
116Required properties:
117- compatible: Should be "fsl,imx-parallel-display"
118Optional properties:
119- interface-pix-fmt: How this display is connected to the
120  display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
121  and "lvds666".
122- edid: verbatim EDID data block describing attached display.
123- ddc: phandle describing the i2c bus handling the display data
124  channel
125- port@[0-1]: Port nodes with endpoint definitions as defined in
126  Documentation/devicetree/bindings/media/video-interfaces.txt.
127  Port 0 is the input port connected to the IPU display interface,
128  port 1 is the output port connected to a panel.
129
130example:
131
132disp0 {
133	compatible = "fsl,imx-parallel-display";
134	edid = [edid-data];
135	interface-pix-fmt = "rgb24";
136
137	port@0 {
138		reg = <0>;
139
140		display_in: endpoint {
141			remote-endpoint = <&ipu_di0_disp0>;
142		};
143	};
144
145	port@1 {
146		reg = <1>;
147
148		display_out: endpoint {
149			remote-endpoint = <&panel_in>;
150		};
151	};
152};
153
154panel {
155	...
156
157	port {
158		panel_in: endpoint {
159			remote-endpoint = <&display_out>;
160		};
161	};
162};
163