xref: /linux/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt (revision 48dea9a700c8728cc31a1dd44588b97578de86ee) 
1ARM Broadcom STB platforms Device Tree Bindings
2-----------------------------------------------
3Boards with Broadcom Brahma15 ARM-based BCMxxxx (generally BCM7xxx variants)
4SoC shall have the following DT organization:
5
6Required root node properties:
7    - compatible: "brcm,bcm<chip_id>", "brcm,brcmstb"
8
9example:
10/ {
11    #address-cells = <2>;
12    #size-cells = <2>;
13    model = "Broadcom STB (bcm7445)";
14    compatible = "brcm,bcm7445", "brcm,brcmstb";
15
16Further, syscon nodes that map platform-specific registers used for general
17system control is required:
18
19    - compatible: "brcm,bcm<chip_id>-sun-top-ctrl", "syscon"
20    - compatible: "brcm,bcm<chip_id>-cpu-biu-ctrl",
21		  "brcm,brcmstb-cpu-biu-ctrl",
22		  "syscon"
23    - compatible: "brcm,bcm<chip_id>-hif-continuation", "syscon"
24
25cpu-biu-ctrl node
26-------------------
27SoCs with Broadcom Brahma15 ARM-based and Brahma53 ARM64-based CPUs have a
28specific Bus Interface Unit (BIU) block which controls and interfaces the CPU
29complex to the different Memory Controller Ports (MCP), one per memory
30controller (MEMC). This BIU block offers a feature called Write Pairing which
31consists in collapsing two adjacent cache lines into a single (bursted) write
32transaction towards the memory controller (MEMC) to maximize write bandwidth.
33
34Required properties:
35
36    - compatible: must be "brcm,bcm7445-cpu-biu-ctrl", "brcm,brcmstb-cpu-biu-ctrl", "syscon"
37
38Optional properties:
39
40    - brcm,write-pairing:
41	Boolean property, which when present indicates that the chip
42	supports write-pairing.
43
44example:
45    rdb {
46        #address-cells = <1>;
47        #size-cells = <1>;
48        compatible = "simple-bus";
49        ranges = <0 0x00 0xf0000000 0x1000000>;
50
51        sun_top_ctrl: syscon@404000 {
52            compatible = "brcm,bcm7445-sun-top-ctrl", "syscon";
53            reg = <0x404000 0x51c>;
54        };
55
56        hif_cpubiuctrl: syscon@3e2400 {
57            compatible = "brcm,bcm7445-cpu-biu-ctrl", "brcm,brcmstb-cpu-biu-ctrl", "syscon";
58            reg = <0x3e2400 0x5b4>;
59            brcm,write-pairing;
60        };
61
62        hif_continuation: syscon@452000 {
63            compatible = "brcm,bcm7445-hif-continuation", "syscon";
64            reg = <0x452000 0x100>;
65        };
66    };
67
68Nodes that allow for support of SMP initialization and reboot are required:
69
70smpboot
71-------
72Required properties:
73
74    - compatible
75        The string "brcm,brcmstb-smpboot".
76
77    - syscon-cpu
78        A phandle / integer array property which lets the BSP know the location
79        of certain CPU power-on registers.
80
81        The layout of the property is as follows:
82            o a phandle to the "hif_cpubiuctrl" syscon node
83            o offset to the base CPU power zone register
84            o offset to the base CPU reset register
85
86    - syscon-cont
87        A phandle pointing to the syscon node which describes the CPU boot
88        continuation registers.
89            o a phandle to the "hif_continuation" syscon node
90
91example:
92    smpboot {
93        compatible = "brcm,brcmstb-smpboot";
94        syscon-cpu = <&hif_cpubiuctrl 0x88 0x178>;
95        syscon-cont = <&hif_continuation>;
96    };
97
98reboot
99-------
100Required properties
101
102    - compatible
103        The string property "brcm,brcmstb-reboot" for 40nm/28nm chips with
104        the new SYS_CTRL interface, or "brcm,bcm7038-reboot" for 65nm
105        chips with the old SUN_TOP_CTRL interface.
106
107    - syscon
108        A phandle / integer array that points to the syscon node which describes
109        the general system reset registers.
110            o a phandle to "sun_top_ctrl"
111            o offset to the "reset source enable" register
112            o offset to the "software master reset" register
113
114example:
115    reboot {
116        compatible = "brcm,brcmstb-reboot";
117        syscon = <&sun_top_ctrl 0x304 0x308>;
118    };
119
120
121
122Power management
123----------------
124
125For power management (particularly, S2/S3/S5 system suspend), the following SoC
126components are needed:
127
128= Always-On control block (AON CTRL)
129
130This hardware provides control registers for the "always-on" (even in low-power
131modes) hardware, such as the Power Management State Machine (PMSM).
132
133Required properties:
134- compatible     : should contain "brcm,brcmstb-aon-ctrl"
135- reg            : the register start and length for the AON CTRL block
136
137Example:
138
139aon-ctrl@410000 {
140	compatible = "brcm,brcmstb-aon-ctrl";
141	reg = <0x410000 0x400>;
142};
143
144= Memory controllers
145
146A Broadcom STB SoC typically has a number of independent memory controllers,
147each of which may have several associated hardware blocks, which are versioned
148independently (control registers, DDR PHYs, etc.). One might consider
149describing these controllers as a parent "memory controllers" block, which
150contains N sub-nodes (one for each controller in the system), each of which is
151associated with a number of hardware register resources (e.g., its PHY). See
152the example device tree snippet below.
153
154== MEMC (MEMory Controller)
155
156Represents a single memory controller instance.
157
158Required properties:
159- compatible     : should contain "brcm,brcmstb-memc" and "simple-bus"
160
161Should contain subnodes for any of the following relevant hardware resources:
162
163== DDR PHY control
164
165Control registers for this memory controller's DDR PHY.
166
167Required properties:
168- compatible     : should contain one of these
169	"brcm,brcmstb-ddr-phy-v71.1"
170	"brcm,brcmstb-ddr-phy-v72.0"
171	"brcm,brcmstb-ddr-phy-v225.1"
172	"brcm,brcmstb-ddr-phy-v240.1"
173	"brcm,brcmstb-ddr-phy-v240.2"
174
175- reg            : the DDR PHY register range
176
177== DDR SHIMPHY
178
179Control registers for this memory controller's DDR SHIMPHY.
180
181Required properties:
182- compatible     : should contain "brcm,brcmstb-ddr-shimphy-v1.0"
183- reg            : the DDR SHIMPHY register range
184
185== MEMC DDR control
186
187Sequencer DRAM parameters and control registers. Used for Self-Refresh
188Power-Down (SRPD), among other things.
189
190Required properties:
191- compatible     : should contain one of these
192	"brcm,brcmstb-memc-ddr-rev-b.2.1"
193	"brcm,brcmstb-memc-ddr-rev-b.2.2"
194	"brcm,brcmstb-memc-ddr-rev-b.2.3"
195	"brcm,brcmstb-memc-ddr-rev-b.3.0"
196	"brcm,brcmstb-memc-ddr-rev-b.3.1"
197	"brcm,brcmstb-memc-ddr"
198- reg            : the MEMC DDR register range
199
200Example:
201
202memory_controllers {
203	ranges;
204	compatible = "simple-bus";
205
206	memc@0 {
207		compatible = "brcm,brcmstb-memc", "simple-bus";
208		ranges;
209
210		ddr-phy@f1106000 {
211			compatible = "brcm,brcmstb-ddr-phy-v240.1";
212			reg = <0xf1106000 0x21c>;
213		};
214
215		shimphy@f1108000 {
216			compatible = "brcm,brcmstb-ddr-shimphy-v1.0";
217			reg = <0xf1108000 0xe4>;
218		};
219
220		memc-ddr@f1102000 {
221			reg = <0xf1102000 0x800>;
222			compatible = "brcm,brcmstb-memc-ddr";
223		};
224	};
225
226	memc@1 {
227		compatible = "brcm,brcmstb-memc", "simple-bus";
228		ranges;
229
230		ddr-phy@f1186000 {
231			compatible = "brcm,brcmstb-ddr-phy-v240.1";
232			reg = <0xf1186000 0x21c>;
233		};
234
235		shimphy@f1188000 {
236			compatible = "brcm,brcmstb-ddr-shimphy-v1.0";
237			reg = <0xf1188000 0xe4>;
238		};
239
240		memc-ddr@f1182000 {
241			reg = <0xf1182000 0x800>;
242			compatible = "brcm,brcmstb-memc-ddr";
243		};
244	};
245
246	memc@2 {
247		compatible = "brcm,brcmstb-memc", "simple-bus";
248		ranges;
249
250		ddr-phy@f1206000 {
251			compatible = "brcm,brcmstb-ddr-phy-v240.1";
252			reg = <0xf1206000 0x21c>;
253		};
254
255		shimphy@f1208000 {
256			compatible = "brcm,brcmstb-ddr-shimphy-v1.0";
257			reg = <0xf1208000 0xe4>;
258		};
259
260		memc-ddr@f1202000 {
261			reg = <0xf1202000 0x800>;
262			compatible = "brcm,brcmstb-memc-ddr";
263		};
264	};
265};
266