1 acpi= [HW,ACPI,X86,ARM64] 2 Advanced Configuration and Power Interface 3 Format: { force | on | off | strict | noirq | rsdt | 4 copy_dsdt } 5 force -- enable ACPI if default was off 6 on -- enable ACPI but allow fallback to DT [arm64] 7 off -- disable ACPI if default was on 8 noirq -- do not use ACPI for IRQ routing 9 strict -- Be less tolerant of platforms that are not 10 strictly ACPI specification compliant. 11 rsdt -- prefer RSDT over (default) XSDT 12 copy_dsdt -- copy DSDT to memory 13 For ARM64, ONLY "acpi=off", "acpi=on" or "acpi=force" 14 are available 15 16 See also Documentation/power/runtime_pm.txt, pci=noacpi 17 18 acpi_apic_instance= [ACPI, IOAPIC] 19 Format: <int> 20 2: use 2nd APIC table, if available 21 1,0: use 1st APIC table 22 default: 0 23 24 acpi_backlight= [HW,ACPI] 25 acpi_backlight=vendor 26 acpi_backlight=video 27 If set to vendor, prefer vendor specific driver 28 (e.g. thinkpad_acpi, sony_acpi, etc.) instead 29 of the ACPI video.ko driver. 30 31 acpi_force_32bit_fadt_addr 32 force FADT to use 32 bit addresses rather than the 33 64 bit X_* addresses. Some firmware have broken 64 34 bit addresses for force ACPI ignore these and use 35 the older legacy 32 bit addresses. 36 37 acpica_no_return_repair [HW, ACPI] 38 Disable AML predefined validation mechanism 39 This mechanism can repair the evaluation result to make 40 the return objects more ACPI specification compliant. 41 This option is useful for developers to identify the 42 root cause of an AML interpreter issue when the issue 43 has something to do with the repair mechanism. 44 45 acpi.debug_layer= [HW,ACPI,ACPI_DEBUG] 46 acpi.debug_level= [HW,ACPI,ACPI_DEBUG] 47 Format: <int> 48 CONFIG_ACPI_DEBUG must be enabled to produce any ACPI 49 debug output. Bits in debug_layer correspond to a 50 _COMPONENT in an ACPI source file, e.g., 51 #define _COMPONENT ACPI_PCI_COMPONENT 52 Bits in debug_level correspond to a level in 53 ACPI_DEBUG_PRINT statements, e.g., 54 ACPI_DEBUG_PRINT((ACPI_DB_INFO, ... 55 The debug_level mask defaults to "info". See 56 Documentation/firmware-guide/acpi/debug.rst for more information about 57 debug layers and levels. 58 59 Enable processor driver info messages: 60 acpi.debug_layer=0x20000000 61 Enable PCI/PCI interrupt routing info messages: 62 acpi.debug_layer=0x400000 63 Enable AML "Debug" output, i.e., stores to the Debug 64 object while interpreting AML: 65 acpi.debug_layer=0xffffffff acpi.debug_level=0x2 66 Enable all messages related to ACPI hardware: 67 acpi.debug_layer=0x2 acpi.debug_level=0xffffffff 68 69 Some values produce so much output that the system is 70 unusable. The "log_buf_len" parameter may be useful 71 if you need to capture more output. 72 73 acpi_enforce_resources= [ACPI] 74 { strict | lax | no } 75 Check for resource conflicts between native drivers 76 and ACPI OperationRegions (SystemIO and SystemMemory 77 only). IO ports and memory declared in ACPI might be 78 used by the ACPI subsystem in arbitrary AML code and 79 can interfere with legacy drivers. 80 strict (default): access to resources claimed by ACPI 81 is denied; legacy drivers trying to access reserved 82 resources will fail to bind to device using them. 83 lax: access to resources claimed by ACPI is allowed; 84 legacy drivers trying to access reserved resources 85 will bind successfully but a warning message is logged. 86 no: ACPI OperationRegions are not marked as reserved, 87 no further checks are performed. 88 89 acpi_force_table_verification [HW,ACPI] 90 Enable table checksum verification during early stage. 91 By default, this is disabled due to x86 early mapping 92 size limitation. 93 94 acpi_irq_balance [HW,ACPI] 95 ACPI will balance active IRQs 96 default in APIC mode 97 98 acpi_irq_nobalance [HW,ACPI] 99 ACPI will not move active IRQs (default) 100 default in PIC mode 101 102 acpi_irq_isa= [HW,ACPI] If irq_balance, mark listed IRQs used by ISA 103 Format: <irq>,<irq>... 104 105 acpi_irq_pci= [HW,ACPI] If irq_balance, clear listed IRQs for 106 use by PCI 107 Format: <irq>,<irq>... 108 109 acpi_mask_gpe= [HW,ACPI] 110 Due to the existence of _Lxx/_Exx, some GPEs triggered 111 by unsupported hardware/firmware features can result in 112 GPE floodings that cannot be automatically disabled by 113 the GPE dispatcher. 114 This facility can be used to prevent such uncontrolled 115 GPE floodings. 116 Format: <int> 117 118 acpi_no_auto_serialize [HW,ACPI] 119 Disable auto-serialization of AML methods 120 AML control methods that contain the opcodes to create 121 named objects will be marked as "Serialized" by the 122 auto-serialization feature. 123 This feature is enabled by default. 124 This option allows to turn off the feature. 125 126 acpi_no_memhotplug [ACPI] Disable memory hotplug. Useful for kdump 127 kernels. 128 129 acpi_no_static_ssdt [HW,ACPI] 130 Disable installation of static SSDTs at early boot time 131 By default, SSDTs contained in the RSDT/XSDT will be 132 installed automatically and they will appear under 133 /sys/firmware/acpi/tables. 134 This option turns off this feature. 135 Note that specifying this option does not affect 136 dynamic table installation which will install SSDT 137 tables to /sys/firmware/acpi/tables/dynamic. 138 139 acpi_rsdp= [ACPI,EFI,KEXEC] 140 Pass the RSDP address to the kernel, mostly used 141 on machines running EFI runtime service to boot the 142 second kernel for kdump. 143 144 acpi_os_name= [HW,ACPI] Tell ACPI BIOS the name of the OS 145 Format: To spoof as Windows 98: ="Microsoft Windows" 146 147 acpi_rev_override [ACPI] Override the _REV object to return 5 (instead 148 of 2 which is mandated by ACPI 6) as the supported ACPI 149 specification revision (when using this switch, it may 150 be necessary to carry out a cold reboot _twice_ in a 151 row to make it take effect on the platform firmware). 152 153 acpi_osi= [HW,ACPI] Modify list of supported OS interface strings 154 acpi_osi="string1" # add string1 155 acpi_osi="!string2" # remove string2 156 acpi_osi=!* # remove all strings 157 acpi_osi=! # disable all built-in OS vendor 158 strings 159 acpi_osi=!! # enable all built-in OS vendor 160 strings 161 acpi_osi= # disable all strings 162 163 'acpi_osi=!' can be used in combination with single or 164 multiple 'acpi_osi="string1"' to support specific OS 165 vendor string(s). Note that such command can only 166 affect the default state of the OS vendor strings, thus 167 it cannot affect the default state of the feature group 168 strings and the current state of the OS vendor strings, 169 specifying it multiple times through kernel command line 170 is meaningless. This command is useful when one do not 171 care about the state of the feature group strings which 172 should be controlled by the OSPM. 173 Examples: 174 1. 'acpi_osi=! acpi_osi="Windows 2000"' is equivalent 175 to 'acpi_osi="Windows 2000" acpi_osi=!', they all 176 can make '_OSI("Windows 2000")' TRUE. 177 178 'acpi_osi=' cannot be used in combination with other 179 'acpi_osi=' command lines, the _OSI method will not 180 exist in the ACPI namespace. NOTE that such command can 181 only affect the _OSI support state, thus specifying it 182 multiple times through kernel command line is also 183 meaningless. 184 Examples: 185 1. 'acpi_osi=' can make 'CondRefOf(_OSI, Local1)' 186 FALSE. 187 188 'acpi_osi=!*' can be used in combination with single or 189 multiple 'acpi_osi="string1"' to support specific 190 string(s). Note that such command can affect the 191 current state of both the OS vendor strings and the 192 feature group strings, thus specifying it multiple times 193 through kernel command line is meaningful. But it may 194 still not able to affect the final state of a string if 195 there are quirks related to this string. This command 196 is useful when one want to control the state of the 197 feature group strings to debug BIOS issues related to 198 the OSPM features. 199 Examples: 200 1. 'acpi_osi="Module Device" acpi_osi=!*' can make 201 '_OSI("Module Device")' FALSE. 202 2. 'acpi_osi=!* acpi_osi="Module Device"' can make 203 '_OSI("Module Device")' TRUE. 204 3. 'acpi_osi=! acpi_osi=!* acpi_osi="Windows 2000"' is 205 equivalent to 206 'acpi_osi=!* acpi_osi=! acpi_osi="Windows 2000"' 207 and 208 'acpi_osi=!* acpi_osi="Windows 2000" acpi_osi=!', 209 they all will make '_OSI("Windows 2000")' TRUE. 210 211 acpi_pm_good [X86] 212 Override the pmtimer bug detection: force the kernel 213 to assume that this machine's pmtimer latches its value 214 and always returns good values. 215 216 acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode 217 Format: { level | edge | high | low } 218 219 acpi_skip_timer_override [HW,ACPI] 220 Recognize and ignore IRQ0/pin2 Interrupt Override. 221 For broken nForce2 BIOS resulting in XT-PIC timer. 222 223 acpi_sleep= [HW,ACPI] Sleep options 224 Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig, 225 old_ordering, nonvs, sci_force_enable, nobl } 226 See Documentation/power/video.txt for information on 227 s3_bios and s3_mode. 228 s3_beep is for debugging; it makes the PC's speaker beep 229 as soon as the kernel's real-mode entry point is called. 230 s4_nohwsig prevents ACPI hardware signature from being 231 used during resume from hibernation. 232 old_ordering causes the ACPI 1.0 ordering of the _PTS 233 control method, with respect to putting devices into 234 low power states, to be enforced (the ACPI 2.0 ordering 235 of _PTS is used by default). 236 nonvs prevents the kernel from saving/restoring the 237 ACPI NVS memory during suspend/hibernation and resume. 238 sci_force_enable causes the kernel to set SCI_EN directly 239 on resume from S1/S3 (which is against the ACPI spec, 240 but some broken systems don't work without it). 241 nobl causes the internal blacklist of systems known to 242 behave incorrectly in some ways with respect to system 243 suspend and resume to be ignored (use wisely). 244 245 acpi_use_timer_override [HW,ACPI] 246 Use timer override. For some broken Nvidia NF5 boards 247 that require a timer override, but don't have HPET 248 249 add_efi_memmap [EFI; X86] Include EFI memory map in 250 kernel's map of available physical RAM. 251 252 agp= [AGP] 253 { off | try_unsupported } 254 off: disable AGP support 255 try_unsupported: try to drive unsupported chipsets 256 (may crash computer or cause data corruption) 257 258 ALSA [HW,ALSA] 259 See Documentation/sound/alsa-configuration.rst 260 261 alignment= [KNL,ARM] 262 Allow the default userspace alignment fault handler 263 behaviour to be specified. Bit 0 enables warnings, 264 bit 1 enables fixups, and bit 2 sends a segfault. 265 266 align_va_addr= [X86-64] 267 Align virtual addresses by clearing slice [14:12] when 268 allocating a VMA at process creation time. This option 269 gives you up to 3% performance improvement on AMD F15h 270 machines (where it is enabled by default) for a 271 CPU-intensive style benchmark, and it can vary highly in 272 a microbenchmark depending on workload and compiler. 273 274 32: only for 32-bit processes 275 64: only for 64-bit processes 276 on: enable for both 32- and 64-bit processes 277 off: disable for both 32- and 64-bit processes 278 279 alloc_snapshot [FTRACE] 280 Allocate the ftrace snapshot buffer on boot up when the 281 main buffer is allocated. This is handy if debugging 282 and you need to use tracing_snapshot() on boot up, and 283 do not want to use tracing_snapshot_alloc() as it needs 284 to be done where GFP_KERNEL allocations are allowed. 285 286 amd_iommu= [HW,X86-64] 287 Pass parameters to the AMD IOMMU driver in the system. 288 Possible values are: 289 fullflush - enable flushing of IO/TLB entries when 290 they are unmapped. Otherwise they are 291 flushed before they will be reused, which 292 is a lot of faster 293 off - do not initialize any AMD IOMMU found in 294 the system 295 force_isolation - Force device isolation for all 296 devices. The IOMMU driver is not 297 allowed anymore to lift isolation 298 requirements as needed. This option 299 does not override iommu=pt 300 301 amd_iommu_dump= [HW,X86-64] 302 Enable AMD IOMMU driver option to dump the ACPI table 303 for AMD IOMMU. With this option enabled, AMD IOMMU 304 driver will print ACPI tables for AMD IOMMU during 305 IOMMU initialization. 306 307 amd_iommu_intr= [HW,X86-64] 308 Specifies one of the following AMD IOMMU interrupt 309 remapping modes: 310 legacy - Use legacy interrupt remapping mode. 311 vapic - Use virtual APIC mode, which allows IOMMU 312 to inject interrupts directly into guest. 313 This mode requires kvm-amd.avic=1. 314 (Default when IOMMU HW support is present.) 315 316 amijoy.map= [HW,JOY] Amiga joystick support 317 Map of devices attached to JOY0DAT and JOY1DAT 318 Format: <a>,<b> 319 See also Documentation/input/joydev/joystick.rst 320 321 analog.map= [HW,JOY] Analog joystick and gamepad support 322 Specifies type or capabilities of an analog joystick 323 connected to one of 16 gameports 324 Format: <type1>,<type2>,..<type16> 325 326 apc= [HW,SPARC] 327 Power management functions (SPARCstation-4/5 + deriv.) 328 Format: noidle 329 Disable APC CPU standby support. SPARCstation-Fox does 330 not play well with APC CPU idle - disable it if you have 331 APC and your system crashes randomly. 332 333 apic= [APIC,X86] Advanced Programmable Interrupt Controller 334 Change the output verbosity while booting 335 Format: { quiet (default) | verbose | debug } 336 Change the amount of debugging information output 337 when initialising the APIC and IO-APIC components. 338 For X86-32, this can also be used to specify an APIC 339 driver name. 340 Format: apic=driver_name 341 Examples: apic=bigsmp 342 343 apic_extnmi= [APIC,X86] External NMI delivery setting 344 Format: { bsp (default) | all | none } 345 bsp: External NMI is delivered only to CPU 0 346 all: External NMIs are broadcast to all CPUs as a 347 backup of CPU 0 348 none: External NMI is masked for all CPUs. This is 349 useful so that a dump capture kernel won't be 350 shot down by NMI 351 352 autoconf= [IPV6] 353 See Documentation/networking/ipv6.txt. 354 355 show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller 356 Limit apic dumping. The parameter defines the maximal 357 number of local apics being dumped. Also it is possible 358 to set it to "all" by meaning -- no limit here. 359 Format: { 1 (default) | 2 | ... | all }. 360 The parameter valid if only apic=debug or 361 apic=verbose is specified. 362 Example: apic=debug show_lapic=all 363 364 apm= [APM] Advanced Power Management 365 See header of arch/x86/kernel/apm_32.c. 366 367 arcrimi= [HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards 368 Format: <io>,<irq>,<nodeID> 369 370 ataflop= [HW,M68k] 371 372 atarimouse= [HW,MOUSE] Atari Mouse 373 374 atkbd.extra= [HW] Enable extra LEDs and keys on IBM RapidAccess, 375 EzKey and similar keyboards 376 377 atkbd.reset= [HW] Reset keyboard during initialization 378 379 atkbd.set= [HW] Select keyboard code set 380 Format: <int> (2 = AT (default), 3 = PS/2) 381 382 atkbd.scroll= [HW] Enable scroll wheel on MS Office and similar 383 keyboards 384 385 atkbd.softraw= [HW] Choose between synthetic and real raw mode 386 Format: <bool> (0 = real, 1 = synthetic (default)) 387 388 atkbd.softrepeat= [HW] 389 Use software keyboard repeat 390 391 audit= [KNL] Enable the audit sub-system 392 Format: { "0" | "1" | "off" | "on" } 393 0 | off - kernel audit is disabled and can not be 394 enabled until the next reboot 395 unset - kernel audit is initialized but disabled and 396 will be fully enabled by the userspace auditd. 397 1 | on - kernel audit is initialized and partially 398 enabled, storing at most audit_backlog_limit 399 messages in RAM until it is fully enabled by the 400 userspace auditd. 401 Default: unset 402 403 audit_backlog_limit= [KNL] Set the audit queue size limit. 404 Format: <int> (must be >=0) 405 Default: 64 406 407 bau= [X86_UV] Enable the BAU on SGI UV. The default 408 behavior is to disable the BAU (i.e. bau=0). 409 Format: { "0" | "1" } 410 0 - Disable the BAU. 411 1 - Enable the BAU. 412 unset - Disable the BAU. 413 414 baycom_epp= [HW,AX25] 415 Format: <io>,<mode> 416 417 baycom_par= [HW,AX25] BayCom Parallel Port AX.25 Modem 418 Format: <io>,<mode> 419 See header of drivers/net/hamradio/baycom_par.c. 420 421 baycom_ser_fdx= [HW,AX25] 422 BayCom Serial Port AX.25 Modem (Full Duplex Mode) 423 Format: <io>,<irq>,<mode>[,<baud>] 424 See header of drivers/net/hamradio/baycom_ser_fdx.c. 425 426 baycom_ser_hdx= [HW,AX25] 427 BayCom Serial Port AX.25 Modem (Half Duplex Mode) 428 Format: <io>,<irq>,<mode> 429 See header of drivers/net/hamradio/baycom_ser_hdx.c. 430 431 blkdevparts= Manual partition parsing of block device(s) for 432 embedded devices based on command line input. 433 See Documentation/block/cmdline-partition.txt 434 435 boot_delay= Milliseconds to delay each printk during boot. 436 Values larger than 10 seconds (10000) are changed to 437 no delay (0). 438 Format: integer 439 440 bootmem_debug [KNL] Enable bootmem allocator debug messages. 441 442 bert_disable [ACPI] 443 Disable BERT OS support on buggy BIOSes. 444 445 bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards) 446 bttv.radio= Most important insmod options are available as 447 kernel args too. 448 bttv.pll= See Documentation/media/v4l-drivers/bttv.rst 449 bttv.tuner= 450 451 bulk_remove=off [PPC] This parameter disables the use of the pSeries 452 firmware feature for flushing multiple hpte entries 453 at a time. 454 455 c101= [NET] Moxa C101 synchronous serial card 456 457 cachesize= [BUGS=X86-32] Override level 2 CPU cache size detection. 458 Sometimes CPU hardware bugs make them report the cache 459 size incorrectly. The kernel will attempt work arounds 460 to fix known problems, but for some CPUs it is not 461 possible to determine what the correct size should be. 462 This option provides an override for these situations. 463 464 carrier_timeout= 465 [NET] Specifies amount of time (in seconds) that 466 the kernel should wait for a network carrier. By default 467 it waits 120 seconds. 468 469 ca_keys= [KEYS] This parameter identifies a specific key(s) on 470 the system trusted keyring to be used for certificate 471 trust validation. 472 format: { id:<keyid> | builtin } 473 474 cca= [MIPS] Override the kernel pages' cache coherency 475 algorithm. Accepted values range from 0 to 7 476 inclusive. See arch/mips/include/asm/pgtable-bits.h 477 for platform specific values (SB1, Loongson3 and 478 others). 479 480 ccw_timeout_log [S390] 481 See Documentation/s390/CommonIO for details. 482 483 cgroup_disable= [KNL] Disable a particular controller 484 Format: {name of the controller(s) to disable} 485 The effects of cgroup_disable=foo are: 486 - foo isn't auto-mounted if you mount all cgroups in 487 a single hierarchy 488 - foo isn't visible as an individually mountable 489 subsystem 490 {Currently only "memory" controller deal with this and 491 cut the overhead, others just disable the usage. So 492 only cgroup_disable=memory is actually worthy} 493 494 cgroup_no_v1= [KNL] Disable cgroup controllers and named hierarchies in v1 495 Format: { { controller | "all" | "named" } 496 [,{ controller | "all" | "named" }...] } 497 Like cgroup_disable, but only applies to cgroup v1; 498 the blacklisted controllers remain available in cgroup2. 499 "all" blacklists all controllers and "named" disables 500 named mounts. Specifying both "all" and "named" disables 501 all v1 hierarchies. 502 503 cgroup.memory= [KNL] Pass options to the cgroup memory controller. 504 Format: <string> 505 nosocket -- Disable socket memory accounting. 506 nokmem -- Disable kernel memory accounting. 507 508 checkreqprot [SELINUX] Set initial checkreqprot flag value. 509 Format: { "0" | "1" } 510 See security/selinux/Kconfig help text. 511 0 -- check protection applied by kernel (includes 512 any implied execute protection). 513 1 -- check protection requested by application. 514 Default value is set via a kernel config option. 515 Value can be changed at runtime via 516 /selinux/checkreqprot. 517 518 cio_ignore= [S390] 519 See Documentation/s390/CommonIO for details. 520 clk_ignore_unused 521 [CLK] 522 Prevents the clock framework from automatically gating 523 clocks that have not been explicitly enabled by a Linux 524 device driver but are enabled in hardware at reset or 525 by the bootloader/firmware. Note that this does not 526 force such clocks to be always-on nor does it reserve 527 those clocks in any way. This parameter is useful for 528 debug and development, but should not be needed on a 529 platform with proper driver support. For more 530 information, see Documentation/driver-api/clk.rst. 531 532 clock= [BUGS=X86-32, HW] gettimeofday clocksource override. 533 [Deprecated] 534 Forces specified clocksource (if available) to be used 535 when calculating gettimeofday(). If specified 536 clocksource is not available, it defaults to PIT. 537 Format: { pit | tsc | cyclone | pmtmr } 538 539 clocksource= Override the default clocksource 540 Format: <string> 541 Override the default clocksource and use the clocksource 542 with the name specified. 543 Some clocksource names to choose from, depending on 544 the platform: 545 [all] jiffies (this is the base, fallback clocksource) 546 [ACPI] acpi_pm 547 [ARM] imx_timer1,OSTS,netx_timer,mpu_timer2, 548 pxa_timer,timer3,32k_counter,timer0_1 549 [X86-32] pit,hpet,tsc; 550 scx200_hrt on Geode; cyclone on IBM x440 551 [MIPS] MIPS 552 [PARISC] cr16 553 [S390] tod 554 [SH] SuperH 555 [SPARC64] tick 556 [X86-64] hpet,tsc 557 558 clocksource.arm_arch_timer.evtstrm= 559 [ARM,ARM64] 560 Format: <bool> 561 Enable/disable the eventstream feature of the ARM 562 architected timer so that code using WFE-based polling 563 loops can be debugged more effectively on production 564 systems. 565 566 clearcpuid=BITNUM [X86] 567 Disable CPUID feature X for the kernel. See 568 arch/x86/include/asm/cpufeatures.h for the valid bit 569 numbers. Note the Linux specific bits are not necessarily 570 stable over kernel options, but the vendor specific 571 ones should be. 572 Also note that user programs calling CPUID directly 573 or using the feature without checking anything 574 will still see it. This just prevents it from 575 being used by the kernel or shown in /proc/cpuinfo. 576 Also note the kernel might malfunction if you disable 577 some critical bits. 578 579 cma=nn[MG]@[start[MG][-end[MG]]] 580 [ARM,X86,KNL] 581 Sets the size of kernel global memory area for 582 contiguous memory allocations and optionally the 583 placement constraint by the physical address range of 584 memory allocations. A value of 0 disables CMA 585 altogether. For more information, see 586 include/linux/dma-contiguous.h 587 588 cmo_free_hint= [PPC] Format: { yes | no } 589 Specify whether pages are marked as being inactive 590 when they are freed. This is used in CMO environments 591 to determine OS memory pressure for page stealing by 592 a hypervisor. 593 Default: yes 594 595 coherent_pool=nn[KMG] [ARM,KNL] 596 Sets the size of memory pool for coherent, atomic dma 597 allocations, by default set to 256K. 598 599 com20020= [HW,NET] ARCnet - COM20020 chipset 600 Format: 601 <io>[,<irq>[,<nodeID>[,<backplane>[,<ckp>[,<timeout>]]]]] 602 603 com90io= [HW,NET] ARCnet - COM90xx chipset (IO-mapped buffers) 604 Format: <io>[,<irq>] 605 606 com90xx= [HW,NET] 607 ARCnet - COM90xx chipset (memory-mapped buffers) 608 Format: <io>[,<irq>[,<memstart>]] 609 610 condev= [HW,S390] console device 611 conmode= 612 613 console= [KNL] Output console device and options. 614 615 tty<n> Use the virtual console device <n>. 616 617 ttyS<n>[,options] 618 ttyUSB0[,options] 619 Use the specified serial port. The options are of 620 the form "bbbbpnf", where "bbbb" is the baud rate, 621 "p" is parity ("n", "o", or "e"), "n" is number of 622 bits, and "f" is flow control ("r" for RTS or 623 omit it). Default is "9600n8". 624 625 See Documentation/admin-guide/serial-console.rst for more 626 information. See 627 Documentation/networking/netconsole.txt for an 628 alternative. 629 630 uart[8250],io,<addr>[,options] 631 uart[8250],mmio,<addr>[,options] 632 uart[8250],mmio16,<addr>[,options] 633 uart[8250],mmio32,<addr>[,options] 634 uart[8250],0x<addr>[,options] 635 Start an early, polled-mode console on the 8250/16550 636 UART at the specified I/O port or MMIO address, 637 switching to the matching ttyS device later. 638 MMIO inter-register address stride is either 8-bit 639 (mmio), 16-bit (mmio16), or 32-bit (mmio32). 640 If none of [io|mmio|mmio16|mmio32], <addr> is assumed 641 to be equivalent to 'mmio'. 'options' are specified in 642 the same format described for ttyS above; if unspecified, 643 the h/w is not re-initialized. 644 645 hvc<n> Use the hypervisor console device <n>. This is for 646 both Xen and PowerPC hypervisors. 647 648 If the device connected to the port is not a TTY but a braille 649 device, prepend "brl," before the device type, for instance 650 console=brl,ttyS0 651 For now, only VisioBraille is supported. 652 653 console_msg_format= 654 [KNL] Change console messages format 655 default 656 By default we print messages on consoles in 657 "[time stamp] text\n" format (time stamp may not be 658 printed, depending on CONFIG_PRINTK_TIME or 659 `printk_time' param). 660 syslog 661 Switch to syslog format: "<%u>[time stamp] text\n" 662 IOW, each message will have a facility and loglevel 663 prefix. The format is similar to one used by syslog() 664 syscall, or to executing "dmesg -S --raw" or to reading 665 from /proc/kmsg. 666 667 consoleblank= [KNL] The console blank (screen saver) timeout in 668 seconds. A value of 0 disables the blank timer. 669 Defaults to 0. 670 671 coredump_filter= 672 [KNL] Change the default value for 673 /proc/<pid>/coredump_filter. 674 See also Documentation/filesystems/proc.txt. 675 676 coresight_cpu_debug.enable 677 [ARM,ARM64] 678 Format: <bool> 679 Enable/disable the CPU sampling based debugging. 680 0: default value, disable debugging 681 1: enable debugging at boot time 682 683 cpuidle.off=1 [CPU_IDLE] 684 disable the cpuidle sub-system 685 686 cpuidle.governor= 687 [CPU_IDLE] Name of the cpuidle governor to use. 688 689 cpufreq.off=1 [CPU_FREQ] 690 disable the cpufreq sub-system 691 692 cpu_init_udelay=N 693 [X86] Delay for N microsec between assert and de-assert 694 of APIC INIT to start processors. This delay occurs 695 on every CPU online, such as boot, and resume from suspend. 696 Default: 10000 697 698 cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver 699 Format: 700 <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>] 701 702 crashkernel=size[KMG][@offset[KMG]] 703 [KNL] Using kexec, Linux can switch to a 'crash kernel' 704 upon panic. This parameter reserves the physical 705 memory region [offset, offset + size] for that kernel 706 image. If '@offset' is omitted, then a suitable offset 707 is selected automatically. 708 [KNL, x86_64] select a region under 4G first, and 709 fall back to reserve region above 4G when '@offset' 710 hasn't been specified. 711 See Documentation/kdump/kdump.rst for further details. 712 713 crashkernel=range1:size1[,range2:size2,...][@offset] 714 [KNL] Same as above, but depends on the memory 715 in the running system. The syntax of range is 716 start-[end] where start and end are both 717 a memory unit (amount[KMG]). See also 718 Documentation/kdump/kdump.rst for an example. 719 720 crashkernel=size[KMG],high 721 [KNL, x86_64] range could be above 4G. Allow kernel 722 to allocate physical memory region from top, so could 723 be above 4G if system have more than 4G ram installed. 724 Otherwise memory region will be allocated below 4G, if 725 available. 726 It will be ignored if crashkernel=X is specified. 727 crashkernel=size[KMG],low 728 [KNL, x86_64] range under 4G. When crashkernel=X,high 729 is passed, kernel could allocate physical memory region 730 above 4G, that cause second kernel crash on system 731 that require some amount of low memory, e.g. swiotlb 732 requires at least 64M+32K low memory, also enough extra 733 low memory is needed to make sure DMA buffers for 32-bit 734 devices won't run out. Kernel would try to allocate at 735 at least 256M below 4G automatically. 736 This one let user to specify own low range under 4G 737 for second kernel instead. 738 0: to disable low allocation. 739 It will be ignored when crashkernel=X,high is not used 740 or memory reserved is below 4G. 741 742 cryptomgr.notests 743 [KNL] Disable crypto self-tests 744 745 cs89x0_dma= [HW,NET] 746 Format: <dma> 747 748 cs89x0_media= [HW,NET] 749 Format: { rj45 | aui | bnc } 750 751 dasd= [HW,NET] 752 See header of drivers/s390/block/dasd_devmap.c. 753 754 db9.dev[2|3]= [HW,JOY] Multisystem joystick support via parallel port 755 (one device per port) 756 Format: <port#>,<type> 757 See also Documentation/input/devices/joystick-parport.rst 758 759 ddebug_query= [KNL,DYNAMIC_DEBUG] Enable debug messages at early boot 760 time. See 761 Documentation/admin-guide/dynamic-debug-howto.rst for 762 details. Deprecated, see dyndbg. 763 764 debug [KNL] Enable kernel debugging (events log level). 765 766 debug_boot_weak_hash 767 [KNL] Enable printing [hashed] pointers early in the 768 boot sequence. If enabled, we use a weak hash instead 769 of siphash to hash pointers. Use this option if you are 770 seeing instances of '(___ptrval___)') and need to see a 771 value (hashed pointer) instead. Cryptographically 772 insecure, please do not use on production kernels. 773 774 debug_locks_verbose= 775 [KNL] verbose self-tests 776 Format=<0|1> 777 Print debugging info while doing the locking API 778 self-tests. 779 We default to 0 (no extra messages), setting it to 780 1 will print _a lot_ more information - normally 781 only useful to kernel developers. 782 783 debug_objects [KNL] Enable object debugging 784 785 no_debug_objects 786 [KNL] Disable object debugging 787 788 debug_guardpage_minorder= 789 [KNL] When CONFIG_DEBUG_PAGEALLOC is set, this 790 parameter allows control of the order of pages that will 791 be intentionally kept free (and hence protected) by the 792 buddy allocator. Bigger value increase the probability 793 of catching random memory corruption, but reduce the 794 amount of memory for normal system use. The maximum 795 possible value is MAX_ORDER/2. Setting this parameter 796 to 1 or 2 should be enough to identify most random 797 memory corruption problems caused by bugs in kernel or 798 driver code when a CPU writes to (or reads from) a 799 random memory location. Note that there exists a class 800 of memory corruptions problems caused by buggy H/W or 801 F/W or by drivers badly programing DMA (basically when 802 memory is written at bus level and the CPU MMU is 803 bypassed) which are not detectable by 804 CONFIG_DEBUG_PAGEALLOC, hence this option will not help 805 tracking down these problems. 806 807 debug_pagealloc= 808 [KNL] When CONFIG_DEBUG_PAGEALLOC is set, this 809 parameter enables the feature at boot time. In 810 default, it is disabled. We can avoid allocating huge 811 chunk of memory for debug pagealloc if we don't enable 812 it at boot time and the system will work mostly same 813 with the kernel built without CONFIG_DEBUG_PAGEALLOC. 814 on: enable the feature 815 816 debugpat [X86] Enable PAT debugging 817 818 decnet.addr= [HW,NET] 819 Format: <area>[,<node>] 820 See also Documentation/networking/decnet.txt. 821 822 default_hugepagesz= 823 [same as hugepagesz=] The size of the default 824 HugeTLB page size. This is the size represented by 825 the legacy /proc/ hugepages APIs, used for SHM, and 826 default size when mounting hugetlbfs filesystems. 827 Defaults to the default architecture's huge page size 828 if not specified. 829 830 deferred_probe_timeout= 831 [KNL] Debugging option to set a timeout in seconds for 832 deferred probe to give up waiting on dependencies to 833 probe. Only specific dependencies (subsystems or 834 drivers) that have opted in will be ignored. A timeout of 0 835 will timeout at the end of initcalls. This option will also 836 dump out devices still on the deferred probe list after 837 retrying. 838 839 dhash_entries= [KNL] 840 Set number of hash buckets for dentry cache. 841 842 disable_1tb_segments [PPC] 843 Disables the use of 1TB hash page table segments. This 844 causes the kernel to fall back to 256MB segments which 845 can be useful when debugging issues that require an SLB 846 miss to occur. 847 848 disable= [IPV6] 849 See Documentation/networking/ipv6.txt. 850 851 hardened_usercopy= 852 [KNL] Under CONFIG_HARDENED_USERCOPY, whether 853 hardening is enabled for this boot. Hardened 854 usercopy checking is used to protect the kernel 855 from reading or writing beyond known memory 856 allocation boundaries as a proactive defense 857 against bounds-checking flaws in the kernel's 858 copy_to_user()/copy_from_user() interface. 859 on Perform hardened usercopy checks (default). 860 off Disable hardened usercopy checks. 861 862 disable_radix [PPC] 863 Disable RADIX MMU mode on POWER9 864 865 disable_cpu_apicid= [X86,APIC,SMP] 866 Format: <int> 867 The number of initial APIC ID for the 868 corresponding CPU to be disabled at boot, 869 mostly used for the kdump 2nd kernel to 870 disable BSP to wake up multiple CPUs without 871 causing system reset or hang due to sending 872 INIT from AP to BSP. 873 874 perf_v4_pmi= [X86,INTEL] 875 Format: <bool> 876 Disable Intel PMU counter freezing feature. 877 The feature only exists starting from 878 Arch Perfmon v4 (Skylake and newer). 879 880 disable_ddw [PPC/PSERIES] 881 Disable Dynamic DMA Window support. Use this if 882 to workaround buggy firmware. 883 884 disable_ipv6= [IPV6] 885 See Documentation/networking/ipv6.txt. 886 887 disable_mtrr_cleanup [X86] 888 The kernel tries to adjust MTRR layout from continuous 889 to discrete, to make X server driver able to add WB 890 entry later. This parameter disables that. 891 892 disable_mtrr_trim [X86, Intel and AMD only] 893 By default the kernel will trim any uncacheable 894 memory out of your available memory pool based on 895 MTRR settings. This parameter disables that behavior, 896 possibly causing your machine to run very slowly. 897 898 disable_timer_pin_1 [X86] 899 Disable PIN 1 of APIC timer 900 Can be useful to work around chipset bugs. 901 902 dis_ucode_ldr [X86] Disable the microcode loader. 903 904 dma_debug=off If the kernel is compiled with DMA_API_DEBUG support, 905 this option disables the debugging code at boot. 906 907 dma_debug_entries=<number> 908 This option allows to tune the number of preallocated 909 entries for DMA-API debugging code. One entry is 910 required per DMA-API allocation. Use this if the 911 DMA-API debugging code disables itself because the 912 architectural default is too low. 913 914 dma_debug_driver=<driver_name> 915 With this option the DMA-API debugging driver 916 filter feature can be enabled at boot time. Just 917 pass the driver to filter for as the parameter. 918 The filter can be disabled or changed to another 919 driver later using sysfs. 920 921 driver_async_probe= [KNL] 922 List of driver names to be probed asynchronously. 923 Format: <driver_name1>,<driver_name2>... 924 925 drm.edid_firmware=[<connector>:]<file>[,[<connector>:]<file>] 926 Broken monitors, graphic adapters, KVMs and EDIDless 927 panels may send no or incorrect EDID data sets. 928 This parameter allows to specify an EDID data sets 929 in the /lib/firmware directory that are used instead. 930 Generic built-in EDID data sets are used, if one of 931 edid/1024x768.bin, edid/1280x1024.bin, 932 edid/1680x1050.bin, or edid/1920x1080.bin is given 933 and no file with the same name exists. Details and 934 instructions how to build your own EDID data are 935 available in Documentation/EDID/HOWTO.txt. An EDID 936 data set will only be used for a particular connector, 937 if its name and a colon are prepended to the EDID 938 name. Each connector may use a unique EDID data 939 set by separating the files with a comma. An EDID 940 data set with no connector name will be used for 941 any connectors not explicitly specified. 942 943 dscc4.setup= [NET] 944 945 dt_cpu_ftrs= [PPC] 946 Format: {"off" | "known"} 947 Control how the dt_cpu_ftrs device-tree binding is 948 used for CPU feature discovery and setup (if it 949 exists). 950 off: Do not use it, fall back to legacy cpu table. 951 known: Do not pass through unknown features to guests 952 or userspace, only those that the kernel is aware of. 953 954 dump_apple_properties [X86] 955 Dump name and content of EFI device properties on 956 x86 Macs. Useful for driver authors to determine 957 what data is available or for reverse-engineering. 958 959 dyndbg[="val"] [KNL,DYNAMIC_DEBUG] 960 module.dyndbg[="val"] 961 Enable debug messages at boot time. See 962 Documentation/admin-guide/dynamic-debug-howto.rst 963 for details. 964 965 nompx [X86] Disables Intel Memory Protection Extensions. 966 See Documentation/x86/intel_mpx.rst for more 967 information about the feature. 968 969 nopku [X86] Disable Memory Protection Keys CPU feature found 970 in some Intel CPUs. 971 972 module.async_probe [KNL] 973 Enable asynchronous probe on this module. 974 975 early_ioremap_debug [KNL] 976 Enable debug messages in early_ioremap support. This 977 is useful for tracking down temporary early mappings 978 which are not unmapped. 979 980 earlycon= [KNL] Output early console device and options. 981 982 [ARM64] The early console is determined by the 983 stdout-path property in device tree's chosen node, 984 or determined by the ACPI SPCR table. 985 986 [X86] When used with no options the early console is 987 determined by the ACPI SPCR table. 988 989 cdns,<addr>[,options] 990 Start an early, polled-mode console on a Cadence 991 (xuartps) serial port at the specified address. Only 992 supported option is baud rate. If baud rate is not 993 specified, the serial port must already be setup and 994 configured. 995 996 uart[8250],io,<addr>[,options] 997 uart[8250],mmio,<addr>[,options] 998 uart[8250],mmio32,<addr>[,options] 999 uart[8250],mmio32be,<addr>[,options] 1000 uart[8250],0x<addr>[,options] 1001 Start an early, polled-mode console on the 8250/16550 1002 UART at the specified I/O port or MMIO address. 1003 MMIO inter-register address stride is either 8-bit 1004 (mmio) or 32-bit (mmio32 or mmio32be). 1005 If none of [io|mmio|mmio32|mmio32be], <addr> is assumed 1006 to be equivalent to 'mmio'. 'options' are specified 1007 in the same format described for "console=ttyS<n>"; if 1008 unspecified, the h/w is not initialized. 1009 1010 pl011,<addr> 1011 pl011,mmio32,<addr> 1012 Start an early, polled-mode console on a pl011 serial 1013 port at the specified address. The pl011 serial port 1014 must already be setup and configured. Options are not 1015 yet supported. If 'mmio32' is specified, then only 1016 the driver will use only 32-bit accessors to read/write 1017 the device registers. 1018 1019 meson,<addr> 1020 Start an early, polled-mode console on a meson serial 1021 port at the specified address. The serial port must 1022 already be setup and configured. Options are not yet 1023 supported. 1024 1025 msm_serial,<addr> 1026 Start an early, polled-mode console on an msm serial 1027 port at the specified address. The serial port 1028 must already be setup and configured. Options are not 1029 yet supported. 1030 1031 msm_serial_dm,<addr> 1032 Start an early, polled-mode console on an msm serial 1033 dm port at the specified address. The serial port 1034 must already be setup and configured. Options are not 1035 yet supported. 1036 1037 owl,<addr> 1038 Start an early, polled-mode console on a serial port 1039 of an Actions Semi SoC, such as S500 or S900, at the 1040 specified address. The serial port must already be 1041 setup and configured. Options are not yet supported. 1042 1043 rda,<addr> 1044 Start an early, polled-mode console on a serial port 1045 of an RDA Micro SoC, such as RDA8810PL, at the 1046 specified address. The serial port must already be 1047 setup and configured. Options are not yet supported. 1048 1049 smh Use ARM semihosting calls for early console. 1050 1051 s3c2410,<addr> 1052 s3c2412,<addr> 1053 s3c2440,<addr> 1054 s3c6400,<addr> 1055 s5pv210,<addr> 1056 exynos4210,<addr> 1057 Use early console provided by serial driver available 1058 on Samsung SoCs, requires selecting proper type and 1059 a correct base address of the selected UART port. The 1060 serial port must already be setup and configured. 1061 Options are not yet supported. 1062 1063 lantiq,<addr> 1064 Start an early, polled-mode console on a lantiq serial 1065 (lqasc) port at the specified address. The serial port 1066 must already be setup and configured. Options are not 1067 yet supported. 1068 1069 lpuart,<addr> 1070 lpuart32,<addr> 1071 Use early console provided by Freescale LP UART driver 1072 found on Freescale Vybrid and QorIQ LS1021A processors. 1073 A valid base address must be provided, and the serial 1074 port must already be setup and configured. 1075 1076 ar3700_uart,<addr> 1077 Start an early, polled-mode console on the 1078 Armada 3700 serial port at the specified 1079 address. The serial port must already be setup 1080 and configured. Options are not yet supported. 1081 1082 qcom_geni,<addr> 1083 Start an early, polled-mode console on a Qualcomm 1084 Generic Interface (GENI) based serial port at the 1085 specified address. The serial port must already be 1086 setup and configured. Options are not yet supported. 1087 1088 efifb,[options] 1089 Start an early, unaccelerated console on the EFI 1090 memory mapped framebuffer (if available). On cache 1091 coherent non-x86 systems that use system memory for 1092 the framebuffer, pass the 'ram' option so that it is 1093 mapped with the correct attributes. 1094 1095 earlyprintk= [X86,SH,ARM,M68k,S390] 1096 earlyprintk=vga 1097 earlyprintk=sclp 1098 earlyprintk=xen 1099 earlyprintk=serial[,ttySn[,baudrate]] 1100 earlyprintk=serial[,0x...[,baudrate]] 1101 earlyprintk=ttySn[,baudrate] 1102 earlyprintk=dbgp[debugController#] 1103 earlyprintk=pciserial[,force],bus:device.function[,baudrate] 1104 earlyprintk=xdbc[xhciController#] 1105 1106 earlyprintk is useful when the kernel crashes before 1107 the normal console is initialized. It is not enabled by 1108 default because it has some cosmetic problems. 1109 1110 Append ",keep" to not disable it when the real console 1111 takes over. 1112 1113 Only one of vga, efi, serial, or usb debug port can 1114 be used at a time. 1115 1116 Currently only ttyS0 and ttyS1 may be specified by 1117 name. Other I/O ports may be explicitly specified 1118 on some architectures (x86 and arm at least) by 1119 replacing ttySn with an I/O port address, like this: 1120 earlyprintk=serial,0x1008,115200 1121 You can find the port for a given device in 1122 /proc/tty/driver/serial: 1123 2: uart:ST16650V2 port:00001008 irq:18 ... 1124 1125 Interaction with the standard serial driver is not 1126 very good. 1127 1128 The VGA and EFI output is eventually overwritten by 1129 the real console. 1130 1131 The xen output can only be used by Xen PV guests. 1132 1133 The sclp output can only be used on s390. 1134 1135 The optional "force" to "pciserial" enables use of a 1136 PCI device even when its classcode is not of the 1137 UART class. 1138 1139 edac_report= [HW,EDAC] Control how to report EDAC event 1140 Format: {"on" | "off" | "force"} 1141 on: enable EDAC to report H/W event. May be overridden 1142 by other higher priority error reporting module. 1143 off: disable H/W event reporting through EDAC. 1144 force: enforce the use of EDAC to report H/W event. 1145 default: on. 1146 1147 ekgdboc= [X86,KGDB] Allow early kernel console debugging 1148 ekgdboc=kbd 1149 1150 This is designed to be used in conjunction with 1151 the boot argument: earlyprintk=vga 1152 1153 edd= [EDD] 1154 Format: {"off" | "on" | "skip[mbr]"} 1155 1156 efi= [EFI] 1157 Format: { "old_map", "nochunk", "noruntime", "debug" } 1158 old_map [X86-64]: switch to the old ioremap-based EFI 1159 runtime services mapping. 32-bit still uses this one by 1160 default. 1161 nochunk: disable reading files in "chunks" in the EFI 1162 boot stub, as chunking can cause problems with some 1163 firmware implementations. 1164 noruntime : disable EFI runtime services support 1165 debug: enable misc debug output 1166 1167 efi_no_storage_paranoia [EFI; X86] 1168 Using this parameter you can use more than 50% of 1169 your efi variable storage. Use this parameter only if 1170 you are really sure that your UEFI does sane gc and 1171 fulfills the spec otherwise your board may brick. 1172 1173 efi_fake_mem= nn[KMG]@ss[KMG]:aa[,nn[KMG]@ss[KMG]:aa,..] [EFI; X86] 1174 Add arbitrary attribute to specific memory range by 1175 updating original EFI memory map. 1176 Region of memory which aa attribute is added to is 1177 from ss to ss+nn. 1178 If efi_fake_mem=2G@4G:0x10000,2G@0x10a0000000:0x10000 1179 is specified, EFI_MEMORY_MORE_RELIABLE(0x10000) 1180 attribute is added to range 0x100000000-0x180000000 and 1181 0x10a0000000-0x1120000000. 1182 1183 Using this parameter you can do debugging of EFI memmap 1184 related feature. For example, you can do debugging of 1185 Address Range Mirroring feature even if your box 1186 doesn't support it. 1187 1188 efivar_ssdt= [EFI; X86] Name of an EFI variable that contains an SSDT 1189 that is to be dynamically loaded by Linux. If there are 1190 multiple variables with the same name but with different 1191 vendor GUIDs, all of them will be loaded. See 1192 Documentation/admin-guide/acpi/ssdt-overlays.rst for details. 1193 1194 1195 eisa_irq_edge= [PARISC,HW] 1196 See header of drivers/parisc/eisa.c. 1197 1198 elanfreq= [X86-32] 1199 See comment before function elanfreq_setup() in 1200 arch/x86/kernel/cpu/cpufreq/elanfreq.c. 1201 1202 elevator= [IOSCHED] 1203 Format: { "mq-deadline" | "kyber" | "bfq" } 1204 See Documentation/block/deadline-iosched.txt, 1205 Documentation/block/kyber-iosched.txt and 1206 Documentation/block/bfq-iosched.txt for details. 1207 1208 elfcorehdr=[size[KMG]@]offset[KMG] [IA64,PPC,SH,X86,S390] 1209 Specifies physical address of start of kernel core 1210 image elf header and optionally the size. Generally 1211 kexec loader will pass this option to capture kernel. 1212 See Documentation/kdump/kdump.rst for details. 1213 1214 enable_mtrr_cleanup [X86] 1215 The kernel tries to adjust MTRR layout from continuous 1216 to discrete, to make X server driver able to add WB 1217 entry later. This parameter enables that. 1218 1219 enable_timer_pin_1 [X86] 1220 Enable PIN 1 of APIC timer 1221 Can be useful to work around chipset bugs 1222 (in particular on some ATI chipsets). 1223 The kernel tries to set a reasonable default. 1224 1225 enforcing [SELINUX] Set initial enforcing status. 1226 Format: {"0" | "1"} 1227 See security/selinux/Kconfig help text. 1228 0 -- permissive (log only, no denials). 1229 1 -- enforcing (deny and log). 1230 Default value is 0. 1231 Value can be changed at runtime via /selinux/enforce. 1232 1233 erst_disable [ACPI] 1234 Disable Error Record Serialization Table (ERST) 1235 support. 1236 1237 ether= [HW,NET] Ethernet cards parameters 1238 This option is obsoleted by the "netdev=" option, which 1239 has equivalent usage. See its documentation for details. 1240 1241 evm= [EVM] 1242 Format: { "fix" } 1243 Permit 'security.evm' to be updated regardless of 1244 current integrity status. 1245 1246 failslab= 1247 fail_page_alloc= 1248 fail_make_request=[KNL] 1249 General fault injection mechanism. 1250 Format: <interval>,<probability>,<space>,<times> 1251 See also Documentation/fault-injection/. 1252 1253 floppy= [HW] 1254 See Documentation/blockdev/floppy.txt. 1255 1256 force_pal_cache_flush 1257 [IA-64] Avoid check_sal_cache_flush which may hang on 1258 buggy SAL_CACHE_FLUSH implementations. Using this 1259 parameter will force ia64_sal_cache_flush to call 1260 ia64_pal_cache_flush instead of SAL_CACHE_FLUSH. 1261 1262 forcepae [X86-32] 1263 Forcefully enable Physical Address Extension (PAE). 1264 Many Pentium M systems disable PAE but may have a 1265 functionally usable PAE implementation. 1266 Warning: use of this parameter will taint the kernel 1267 and may cause unknown problems. 1268 1269 ftrace=[tracer] 1270 [FTRACE] will set and start the specified tracer 1271 as early as possible in order to facilitate early 1272 boot debugging. 1273 1274 ftrace_dump_on_oops[=orig_cpu] 1275 [FTRACE] will dump the trace buffers on oops. 1276 If no parameter is passed, ftrace will dump 1277 buffers of all CPUs, but if you pass orig_cpu, it will 1278 dump only the buffer of the CPU that triggered the 1279 oops. 1280 1281 ftrace_filter=[function-list] 1282 [FTRACE] Limit the functions traced by the function 1283 tracer at boot up. function-list is a comma separated 1284 list of functions. This list can be changed at run 1285 time by the set_ftrace_filter file in the debugfs 1286 tracing directory. 1287 1288 ftrace_notrace=[function-list] 1289 [FTRACE] Do not trace the functions specified in 1290 function-list. This list can be changed at run time 1291 by the set_ftrace_notrace file in the debugfs 1292 tracing directory. 1293 1294 ftrace_graph_filter=[function-list] 1295 [FTRACE] Limit the top level callers functions traced 1296 by the function graph tracer at boot up. 1297 function-list is a comma separated list of functions 1298 that can be changed at run time by the 1299 set_graph_function file in the debugfs tracing directory. 1300 1301 ftrace_graph_notrace=[function-list] 1302 [FTRACE] Do not trace from the functions specified in 1303 function-list. This list is a comma separated list of 1304 functions that can be changed at run time by the 1305 set_graph_notrace file in the debugfs tracing directory. 1306 1307 ftrace_graph_max_depth=<uint> 1308 [FTRACE] Used with the function graph tracer. This is 1309 the max depth it will trace into a function. This value 1310 can be changed at run time by the max_graph_depth file 1311 in the tracefs tracing directory. default: 0 (no limit) 1312 1313 gamecon.map[2|3]= 1314 [HW,JOY] Multisystem joystick and NES/SNES/PSX pad 1315 support via parallel port (up to 5 devices per port) 1316 Format: <port#>,<pad1>,<pad2>,<pad3>,<pad4>,<pad5> 1317 See also Documentation/input/devices/joystick-parport.rst 1318 1319 gamma= [HW,DRM] 1320 1321 gart_fix_e820= [X86_64] disable the fix e820 for K8 GART 1322 Format: off | on 1323 default: on 1324 1325 gcov_persist= [GCOV] When non-zero (default), profiling data for 1326 kernel modules is saved and remains accessible via 1327 debugfs, even when the module is unloaded/reloaded. 1328 When zero, profiling data is discarded and associated 1329 debugfs files are removed at module unload time. 1330 1331 goldfish [X86] Enable the goldfish android emulator platform. 1332 Don't use this when you are not running on the 1333 android emulator 1334 1335 gpt [EFI] Forces disk with valid GPT signature but 1336 invalid Protective MBR to be treated as GPT. If the 1337 primary GPT is corrupted, it enables the backup/alternate 1338 GPT to be used instead. 1339 1340 grcan.enable0= [HW] Configuration of physical interface 0. Determines 1341 the "Enable 0" bit of the configuration register. 1342 Format: 0 | 1 1343 Default: 0 1344 grcan.enable1= [HW] Configuration of physical interface 1. Determines 1345 the "Enable 0" bit of the configuration register. 1346 Format: 0 | 1 1347 Default: 0 1348 grcan.select= [HW] Select which physical interface to use. 1349 Format: 0 | 1 1350 Default: 0 1351 grcan.txsize= [HW] Sets the size of the tx buffer. 1352 Format: <unsigned int> such that (txsize & ~0x1fffc0) == 0. 1353 Default: 1024 1354 grcan.rxsize= [HW] Sets the size of the rx buffer. 1355 Format: <unsigned int> such that (rxsize & ~0x1fffc0) == 0. 1356 Default: 1024 1357 1358 gpio-mockup.gpio_mockup_ranges 1359 [HW] Sets the ranges of gpiochip of for this device. 1360 Format: <start1>,<end1>,<start2>,<end2>... 1361 1362 hardlockup_all_cpu_backtrace= 1363 [KNL] Should the hard-lockup detector generate 1364 backtraces on all cpus. 1365 Format: <integer> 1366 1367 hashdist= [KNL,NUMA] Large hashes allocated during boot 1368 are distributed across NUMA nodes. Defaults on 1369 for 64-bit NUMA, off otherwise. 1370 Format: 0 | 1 (for off | on) 1371 1372 hcl= [IA-64] SGI's Hardware Graph compatibility layer 1373 1374 hd= [EIDE] (E)IDE hard drive subsystem geometry 1375 Format: <cyl>,<head>,<sect> 1376 1377 hest_disable [ACPI] 1378 Disable Hardware Error Source Table (HEST) support; 1379 corresponding firmware-first mode error processing 1380 logic will be disabled. 1381 1382 highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact 1383 size of <nn>. This works even on boxes that have no 1384 highmem otherwise. This also works to reduce highmem 1385 size on bigger boxes. 1386 1387 highres= [KNL] Enable/disable high resolution timer mode. 1388 Valid parameters: "on", "off" 1389 Default: "on" 1390 1391 hlt [BUGS=ARM,SH] 1392 1393 hpet= [X86-32,HPET] option to control HPET usage 1394 Format: { enable (default) | disable | force | 1395 verbose } 1396 disable: disable HPET and use PIT instead 1397 force: allow force enabled of undocumented chips (ICH4, 1398 VIA, nVidia) 1399 verbose: show contents of HPET registers during setup 1400 1401 hpet_mmap= [X86, HPET_MMAP] Allow userspace to mmap HPET 1402 registers. Default set by CONFIG_HPET_MMAP_DEFAULT. 1403 1404 hugepages= [HW,X86-32,IA-64] HugeTLB pages to allocate at boot. 1405 hugepagesz= [HW,IA-64,PPC,X86-64] The size of the HugeTLB pages. 1406 On x86-64 and powerpc, this option can be specified 1407 multiple times interleaved with hugepages= to reserve 1408 huge pages of different sizes. Valid pages sizes on 1409 x86-64 are 2M (when the CPU supports "pse") and 1G 1410 (when the CPU supports the "pdpe1gb" cpuinfo flag). 1411 1412 hung_task_panic= 1413 [KNL] Should the hung task detector generate panics. 1414 Format: <integer> 1415 1416 A nonzero value instructs the kernel to panic when a 1417 hung task is detected. The default value is controlled 1418 by the CONFIG_BOOTPARAM_HUNG_TASK_PANIC build-time 1419 option. The value selected by this boot parameter can 1420 be changed later by the kernel.hung_task_panic sysctl. 1421 1422 hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC) 1423 terminal devices. Valid values: 0..8 1424 hvc_iucv_allow= [S390] Comma-separated list of z/VM user IDs. 1425 If specified, z/VM IUCV HVC accepts connections 1426 from listed z/VM user IDs only. 1427 1428 hv_nopvspin [X86,HYPER_V] Disables the paravirt spinlock optimizations 1429 which allow the hypervisor to 'idle' the 1430 guest on lock contention. 1431 1432 keep_bootcon [KNL] 1433 Do not unregister boot console at start. This is only 1434 useful for debugging when something happens in the window 1435 between unregistering the boot console and initializing 1436 the real console. 1437 1438 i2c_bus= [HW] Override the default board specific I2C bus speed 1439 or register an additional I2C bus that is not 1440 registered from board initialization code. 1441 Format: 1442 <bus_id>,<clkrate> 1443 1444 i8042.debug [HW] Toggle i8042 debug mode 1445 i8042.unmask_kbd_data 1446 [HW] Enable printing of interrupt data from the KBD port 1447 (disabled by default, and as a pre-condition 1448 requires that i8042.debug=1 be enabled) 1449 i8042.direct [HW] Put keyboard port into non-translated mode 1450 i8042.dumbkbd [HW] Pretend that controller can only read data from 1451 keyboard and cannot control its state 1452 (Don't attempt to blink the leds) 1453 i8042.noaux [HW] Don't check for auxiliary (== mouse) port 1454 i8042.nokbd [HW] Don't check/create keyboard port 1455 i8042.noloop [HW] Disable the AUX Loopback command while probing 1456 for the AUX port 1457 i8042.nomux [HW] Don't check presence of an active multiplexing 1458 controller 1459 i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX 1460 controllers 1461 i8042.notimeout [HW] Ignore timeout condition signalled by controller 1462 i8042.reset [HW] Reset the controller during init, cleanup and 1463 suspend-to-ram transitions, only during s2r 1464 transitions, or never reset 1465 Format: { 1 | Y | y | 0 | N | n } 1466 1, Y, y: always reset controller 1467 0, N, n: don't ever reset controller 1468 Default: only on s2r transitions on x86; most other 1469 architectures force reset to be always executed 1470 i8042.unlock [HW] Unlock (ignore) the keylock 1471 i8042.kbdreset [HW] Reset device connected to KBD port 1472 1473 i810= [HW,DRM] 1474 1475 i8k.ignore_dmi [HW] Continue probing hardware even if DMI data 1476 indicates that the driver is running on unsupported 1477 hardware. 1478 i8k.force [HW] Activate i8k driver even if SMM BIOS signature 1479 does not match list of supported models. 1480 i8k.power_status 1481 [HW] Report power status in /proc/i8k 1482 (disabled by default) 1483 i8k.restricted [HW] Allow controlling fans only if SYS_ADMIN 1484 capability is set. 1485 1486 i915.invert_brightness= 1487 [DRM] Invert the sense of the variable that is used to 1488 set the brightness of the panel backlight. Normally a 1489 brightness value of 0 indicates backlight switched off, 1490 and the maximum of the brightness value sets the backlight 1491 to maximum brightness. If this parameter is set to 0 1492 (default) and the machine requires it, or this parameter 1493 is set to 1, a brightness value of 0 sets the backlight 1494 to maximum brightness, and the maximum of the brightness 1495 value switches the backlight off. 1496 -1 -- never invert brightness 1497 0 -- machine default 1498 1 -- force brightness inversion 1499 1500 icn= [HW,ISDN] 1501 Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]] 1502 1503 ide-core.nodma= [HW] (E)IDE subsystem 1504 Format: =0.0 to prevent dma on hda, =0.1 hdb =1.0 hdc 1505 .vlb_clock .pci_clock .noflush .nohpa .noprobe .nowerr 1506 .cdrom .chs .ignore_cable are additional options 1507 See Documentation/ide/ide.rst. 1508 1509 ide-generic.probe-mask= [HW] (E)IDE subsystem 1510 Format: <int> 1511 Probe mask for legacy ISA IDE ports. Depending on 1512 platform up to 6 ports are supported, enabled by 1513 setting corresponding bits in the mask to 1. The 1514 default value is 0x0, which has a special meaning. 1515 On systems that have PCI, it triggers scanning the 1516 PCI bus for the first and the second port, which 1517 are then probed. On systems without PCI the value 1518 of 0x0 enables probing the two first ports as if it 1519 was 0x3. 1520 1521 ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem 1522 Claim all unknown PCI IDE storage controllers. 1523 1524 idle= [X86] 1525 Format: idle=poll, idle=halt, idle=nomwait 1526 Poll forces a polling idle loop that can slightly 1527 improve the performance of waking up a idle CPU, but 1528 will use a lot of power and make the system run hot. 1529 Not recommended. 1530 idle=halt: Halt is forced to be used for CPU idle. 1531 In such case C2/C3 won't be used again. 1532 idle=nomwait: Disable mwait for CPU C-states 1533 1534 ieee754= [MIPS] Select IEEE Std 754 conformance mode 1535 Format: { strict | legacy | 2008 | relaxed } 1536 Default: strict 1537 1538 Choose which programs will be accepted for execution 1539 based on the IEEE 754 NaN encoding(s) supported by 1540 the FPU and the NaN encoding requested with the value 1541 of an ELF file header flag individually set by each 1542 binary. Hardware implementations are permitted to 1543 support either or both of the legacy and the 2008 NaN 1544 encoding mode. 1545 1546 Available settings are as follows: 1547 strict accept binaries that request a NaN encoding 1548 supported by the FPU 1549 legacy only accept legacy-NaN binaries, if supported 1550 by the FPU 1551 2008 only accept 2008-NaN binaries, if supported 1552 by the FPU 1553 relaxed accept any binaries regardless of whether 1554 supported by the FPU 1555 1556 The FPU emulator is always able to support both NaN 1557 encodings, so if no FPU hardware is present or it has 1558 been disabled with 'nofpu', then the settings of 1559 'legacy' and '2008' strap the emulator accordingly, 1560 'relaxed' straps the emulator for both legacy-NaN and 1561 2008-NaN, whereas 'strict' enables legacy-NaN only on 1562 legacy processors and both NaN encodings on MIPS32 or 1563 MIPS64 CPUs. 1564 1565 The setting for ABS.fmt/NEG.fmt instruction execution 1566 mode generally follows that for the NaN encoding, 1567 except where unsupported by hardware. 1568 1569 ignore_loglevel [KNL] 1570 Ignore loglevel setting - this will print /all/ 1571 kernel messages to the console. Useful for debugging. 1572 We also add it as printk module parameter, so users 1573 could change it dynamically, usually by 1574 /sys/module/printk/parameters/ignore_loglevel. 1575 1576 ignore_rlimit_data 1577 Ignore RLIMIT_DATA setting for data mappings, 1578 print warning at first misuse. Can be changed via 1579 /sys/module/kernel/parameters/ignore_rlimit_data. 1580 1581 ihash_entries= [KNL] 1582 Set number of hash buckets for inode cache. 1583 1584 ima_appraise= [IMA] appraise integrity measurements 1585 Format: { "off" | "enforce" | "fix" | "log" } 1586 default: "enforce" 1587 1588 ima_appraise_tcb [IMA] Deprecated. Use ima_policy= instead. 1589 The builtin appraise policy appraises all files 1590 owned by uid=0. 1591 1592 ima_canonical_fmt [IMA] 1593 Use the canonical format for the binary runtime 1594 measurements, instead of host native format. 1595 1596 ima_hash= [IMA] 1597 Format: { md5 | sha1 | rmd160 | sha256 | sha384 1598 | sha512 | ... } 1599 default: "sha1" 1600 1601 The list of supported hash algorithms is defined 1602 in crypto/hash_info.h. 1603 1604 ima_policy= [IMA] 1605 The builtin policies to load during IMA setup. 1606 Format: "tcb | appraise_tcb | secure_boot | 1607 fail_securely" 1608 1609 The "tcb" policy measures all programs exec'd, files 1610 mmap'd for exec, and all files opened with the read 1611 mode bit set by either the effective uid (euid=0) or 1612 uid=0. 1613 1614 The "appraise_tcb" policy appraises the integrity of 1615 all files owned by root. 1616 1617 The "secure_boot" policy appraises the integrity 1618 of files (eg. kexec kernel image, kernel modules, 1619 firmware, policy, etc) based on file signatures. 1620 1621 The "fail_securely" policy forces file signature 1622 verification failure also on privileged mounted 1623 filesystems with the SB_I_UNVERIFIABLE_SIGNATURE 1624 flag. 1625 1626 ima_tcb [IMA] Deprecated. Use ima_policy= instead. 1627 Load a policy which meets the needs of the Trusted 1628 Computing Base. This means IMA will measure all 1629 programs exec'd, files mmap'd for exec, and all files 1630 opened for read by uid=0. 1631 1632 ima_template= [IMA] 1633 Select one of defined IMA measurements template formats. 1634 Formats: { "ima" | "ima-ng" | "ima-sig" } 1635 Default: "ima-ng" 1636 1637 ima_template_fmt= 1638 [IMA] Define a custom template format. 1639 Format: { "field1|...|fieldN" } 1640 1641 ima.ahash_minsize= [IMA] Minimum file size for asynchronous hash usage 1642 Format: <min_file_size> 1643 Set the minimal file size for using asynchronous hash. 1644 If left unspecified, ahash usage is disabled. 1645 1646 ahash performance varies for different data sizes on 1647 different crypto accelerators. This option can be used 1648 to achieve the best performance for a particular HW. 1649 1650 ima.ahash_bufsize= [IMA] Asynchronous hash buffer size 1651 Format: <bufsize> 1652 Set hashing buffer size. Default: 4k. 1653 1654 ahash performance varies for different chunk sizes on 1655 different crypto accelerators. This option can be used 1656 to achieve best performance for particular HW. 1657 1658 init= [KNL] 1659 Format: <full_path> 1660 Run specified binary instead of /sbin/init as init 1661 process. 1662 1663 initcall_debug [KNL] Trace initcalls as they are executed. Useful 1664 for working out where the kernel is dying during 1665 startup. 1666 1667 initcall_blacklist= [KNL] Do not execute a comma-separated list of 1668 initcall functions. Useful for debugging built-in 1669 modules and initcalls. 1670 1671 initrd= [BOOT] Specify the location of the initial ramdisk 1672 1673 init_pkru= [x86] Specify the default memory protection keys rights 1674 register contents for all processes. 0x55555554 by 1675 default (disallow access to all but pkey 0). Can 1676 override in debugfs after boot. 1677 1678 inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver 1679 Format: <irq> 1680 1681 int_pln_enable [x86] Enable power limit notification interrupt 1682 1683 integrity_audit=[IMA] 1684 Format: { "0" | "1" } 1685 0 -- basic integrity auditing messages. (Default) 1686 1 -- additional integrity auditing messages. 1687 1688 intel_iommu= [DMAR] Intel IOMMU driver (DMAR) option 1689 on 1690 Enable intel iommu driver. 1691 off 1692 Disable intel iommu driver. 1693 igfx_off [Default Off] 1694 By default, gfx is mapped as normal device. If a gfx 1695 device has a dedicated DMAR unit, the DMAR unit is 1696 bypassed by not enabling DMAR with this option. In 1697 this case, gfx device will use physical address for 1698 DMA. 1699 forcedac [x86_64] 1700 With this option iommu will not optimize to look 1701 for io virtual address below 32-bit forcing dual 1702 address cycle on pci bus for cards supporting greater 1703 than 32-bit addressing. The default is to look 1704 for translation below 32-bit and if not available 1705 then look in the higher range. 1706 strict [Default Off] 1707 With this option on every unmap_single operation will 1708 result in a hardware IOTLB flush operation as opposed 1709 to batching them for performance. 1710 sp_off [Default Off] 1711 By default, super page will be supported if Intel IOMMU 1712 has the capability. With this option, super page will 1713 not be supported. 1714 sm_on [Default Off] 1715 By default, scalable mode will be disabled even if the 1716 hardware advertises that it has support for the scalable 1717 mode translation. With this option set, scalable mode 1718 will be used on hardware which claims to support it. 1719 tboot_noforce [Default Off] 1720 Do not force the Intel IOMMU enabled under tboot. 1721 By default, tboot will force Intel IOMMU on, which 1722 could harm performance of some high-throughput 1723 devices like 40GBit network cards, even if identity 1724 mapping is enabled. 1725 Note that using this option lowers the security 1726 provided by tboot because it makes the system 1727 vulnerable to DMA attacks. 1728 1729 intel_idle.max_cstate= [KNL,HW,ACPI,X86] 1730 0 disables intel_idle and fall back on acpi_idle. 1731 1 to 9 specify maximum depth of C-state. 1732 1733 intel_pstate= [X86] 1734 disable 1735 Do not enable intel_pstate as the default 1736 scaling driver for the supported processors 1737 passive 1738 Use intel_pstate as a scaling driver, but configure it 1739 to work with generic cpufreq governors (instead of 1740 enabling its internal governor). This mode cannot be 1741 used along with the hardware-managed P-states (HWP) 1742 feature. 1743 force 1744 Enable intel_pstate on systems that prohibit it by default 1745 in favor of acpi-cpufreq. Forcing the intel_pstate driver 1746 instead of acpi-cpufreq may disable platform features, such 1747 as thermal controls and power capping, that rely on ACPI 1748 P-States information being indicated to OSPM and therefore 1749 should be used with caution. This option does not work with 1750 processors that aren't supported by the intel_pstate driver 1751 or on platforms that use pcc-cpufreq instead of acpi-cpufreq. 1752 no_hwp 1753 Do not enable hardware P state control (HWP) 1754 if available. 1755 hwp_only 1756 Only load intel_pstate on systems which support 1757 hardware P state control (HWP) if available. 1758 support_acpi_ppc 1759 Enforce ACPI _PPC performance limits. If the Fixed ACPI 1760 Description Table, specifies preferred power management 1761 profile as "Enterprise Server" or "Performance Server", 1762 then this feature is turned on by default. 1763 per_cpu_perf_limits 1764 Allow per-logical-CPU P-State performance control limits using 1765 cpufreq sysfs interface 1766 1767 intremap= [X86-64, Intel-IOMMU] 1768 on enable Interrupt Remapping (default) 1769 off disable Interrupt Remapping 1770 nosid disable Source ID checking 1771 no_x2apic_optout 1772 BIOS x2APIC opt-out request will be ignored 1773 nopost disable Interrupt Posting 1774 1775 iomem= Disable strict checking of access to MMIO memory 1776 strict regions from userspace. 1777 relaxed 1778 1779 iommu= [x86] 1780 off 1781 force 1782 noforce 1783 biomerge 1784 panic 1785 nopanic 1786 merge 1787 nomerge 1788 soft 1789 pt [x86] 1790 nopt [x86] 1791 nobypass [PPC/POWERNV] 1792 Disable IOMMU bypass, using IOMMU for PCI devices. 1793 1794 iommu.strict= [ARM64] Configure TLB invalidation behaviour 1795 Format: { "0" | "1" } 1796 0 - Lazy mode. 1797 Request that DMA unmap operations use deferred 1798 invalidation of hardware TLBs, for increased 1799 throughput at the cost of reduced device isolation. 1800 Will fall back to strict mode if not supported by 1801 the relevant IOMMU driver. 1802 1 - Strict mode (default). 1803 DMA unmap operations invalidate IOMMU hardware TLBs 1804 synchronously. 1805 1806 iommu.passthrough= 1807 [ARM64] Configure DMA to bypass the IOMMU by default. 1808 Format: { "0" | "1" } 1809 0 - Use IOMMU translation for DMA. 1810 1 - Bypass the IOMMU for DMA. 1811 unset - Use value of CONFIG_IOMMU_DEFAULT_PASSTHROUGH. 1812 1813 io7= [HW] IO7 for Marvel based alpha systems 1814 See comment before marvel_specify_io7 in 1815 arch/alpha/kernel/core_marvel.c. 1816 1817 io_delay= [X86] I/O delay method 1818 0x80 1819 Standard port 0x80 based delay 1820 0xed 1821 Alternate port 0xed based delay (needed on some systems) 1822 udelay 1823 Simple two microseconds delay 1824 none 1825 No delay 1826 1827 ip= [IP_PNP] 1828 See Documentation/filesystems/nfs/nfsroot.txt. 1829 1830 ipcmni_extend [KNL] Extend the maximum number of unique System V 1831 IPC identifiers from 32,768 to 16,777,216. 1832 1833 irqaffinity= [SMP] Set the default irq affinity mask 1834 The argument is a cpu list, as described above. 1835 1836 irqchip.gicv2_force_probe= 1837 [ARM, ARM64] 1838 Format: <bool> 1839 Force the kernel to look for the second 4kB page 1840 of a GICv2 controller even if the memory range 1841 exposed by the device tree is too small. 1842 1843 irqchip.gicv3_nolpi= 1844 [ARM, ARM64] 1845 Force the kernel to ignore the availability of 1846 LPIs (and by consequence ITSs). Intended for system 1847 that use the kernel as a bootloader, and thus want 1848 to let secondary kernels in charge of setting up 1849 LPIs. 1850 1851 irqchip.gicv3_pseudo_nmi= [ARM64] 1852 Enables support for pseudo-NMIs in the kernel. This 1853 requires the kernel to be built with 1854 CONFIG_ARM64_PSEUDO_NMI. 1855 1856 irqfixup [HW] 1857 When an interrupt is not handled search all handlers 1858 for it. Intended to get systems with badly broken 1859 firmware running. 1860 1861 irqpoll [HW] 1862 When an interrupt is not handled search all handlers 1863 for it. Also check all handlers each timer 1864 interrupt. Intended to get systems with badly broken 1865 firmware running. 1866 1867 isapnp= [ISAPNP] 1868 Format: <RDP>,<reset>,<pci_scan>,<verbosity> 1869 1870 isolcpus= [KNL,SMP,ISOL] Isolate a given set of CPUs from disturbance. 1871 [Deprecated - use cpusets instead] 1872 Format: [flag-list,]<cpu-list> 1873 1874 Specify one or more CPUs to isolate from disturbances 1875 specified in the flag list (default: domain): 1876 1877 nohz 1878 Disable the tick when a single task runs. 1879 1880 A residual 1Hz tick is offloaded to workqueues, which you 1881 need to affine to housekeeping through the global 1882 workqueue's affinity configured via the 1883 /sys/devices/virtual/workqueue/cpumask sysfs file, or 1884 by using the 'domain' flag described below. 1885 1886 NOTE: by default the global workqueue runs on all CPUs, 1887 so to protect individual CPUs the 'cpumask' file has to 1888 be configured manually after bootup. 1889 1890 domain 1891 Isolate from the general SMP balancing and scheduling 1892 algorithms. Note that performing domain isolation this way 1893 is irreversible: it's not possible to bring back a CPU to 1894 the domains once isolated through isolcpus. It's strongly 1895 advised to use cpusets instead to disable scheduler load 1896 balancing through the "cpuset.sched_load_balance" file. 1897 It offers a much more flexible interface where CPUs can 1898 move in and out of an isolated set anytime. 1899 1900 You can move a process onto or off an "isolated" CPU via 1901 the CPU affinity syscalls or cpuset. 1902 <cpu number> begins at 0 and the maximum value is 1903 "number of CPUs in system - 1". 1904 1905 The format of <cpu-list> is described above. 1906 1907 1908 1909 iucv= [HW,NET] 1910 1911 ivrs_ioapic [HW,X86_64] 1912 Provide an override to the IOAPIC-ID<->DEVICE-ID 1913 mapping provided in the IVRS ACPI table. For 1914 example, to map IOAPIC-ID decimal 10 to 1915 PCI device 00:14.0 write the parameter as: 1916 ivrs_ioapic[10]=00:14.0 1917 1918 ivrs_hpet [HW,X86_64] 1919 Provide an override to the HPET-ID<->DEVICE-ID 1920 mapping provided in the IVRS ACPI table. For 1921 example, to map HPET-ID decimal 0 to 1922 PCI device 00:14.0 write the parameter as: 1923 ivrs_hpet[0]=00:14.0 1924 1925 ivrs_acpihid [HW,X86_64] 1926 Provide an override to the ACPI-HID:UID<->DEVICE-ID 1927 mapping provided in the IVRS ACPI table. For 1928 example, to map UART-HID:UID AMD0020:0 to 1929 PCI device 00:14.5 write the parameter as: 1930 ivrs_acpihid[00:14.5]=AMD0020:0 1931 1932 js= [HW,JOY] Analog joystick 1933 See Documentation/input/joydev/joystick.rst. 1934 1935 nokaslr [KNL] 1936 When CONFIG_RANDOMIZE_BASE is set, this disables 1937 kernel and module base offset ASLR (Address Space 1938 Layout Randomization). 1939 1940 kasan_multi_shot 1941 [KNL] Enforce KASAN (Kernel Address Sanitizer) to print 1942 report on every invalid memory access. Without this 1943 parameter KASAN will print report only for the first 1944 invalid access. 1945 1946 keepinitrd [HW,ARM] 1947 1948 kernelcore= [KNL,X86,IA-64,PPC] 1949 Format: nn[KMGTPE] | nn% | "mirror" 1950 This parameter specifies the amount of memory usable by 1951 the kernel for non-movable allocations. The requested 1952 amount is spread evenly throughout all nodes in the 1953 system as ZONE_NORMAL. The remaining memory is used for 1954 movable memory in its own zone, ZONE_MOVABLE. In the 1955 event, a node is too small to have both ZONE_NORMAL and 1956 ZONE_MOVABLE, kernelcore memory will take priority and 1957 other nodes will have a larger ZONE_MOVABLE. 1958 1959 ZONE_MOVABLE is used for the allocation of pages that 1960 may be reclaimed or moved by the page migration 1961 subsystem. Note that allocations like PTEs-from-HighMem 1962 still use the HighMem zone if it exists, and the Normal 1963 zone if it does not. 1964 1965 It is possible to specify the exact amount of memory in 1966 the form of "nn[KMGTPE]", a percentage of total system 1967 memory in the form of "nn%", or "mirror". If "mirror" 1968 option is specified, mirrored (reliable) memory is used 1969 for non-movable allocations and remaining memory is used 1970 for Movable pages. "nn[KMGTPE]", "nn%", and "mirror" 1971 are exclusive, so you cannot specify multiple forms. 1972 1973 kgdbdbgp= [KGDB,HW] kgdb over EHCI usb debug port. 1974 Format: <Controller#>[,poll interval] 1975 The controller # is the number of the ehci usb debug 1976 port as it is probed via PCI. The poll interval is 1977 optional and is the number seconds in between 1978 each poll cycle to the debug port in case you need 1979 the functionality for interrupting the kernel with 1980 gdb or control-c on the dbgp connection. When 1981 not using this parameter you use sysrq-g to break into 1982 the kernel debugger. 1983 1984 kgdboc= [KGDB,HW] kgdb over consoles. 1985 Requires a tty driver that supports console polling, 1986 or a supported polling keyboard driver (non-usb). 1987 Serial only format: <serial_device>[,baud] 1988 keyboard only format: kbd 1989 keyboard and serial format: kbd,<serial_device>[,baud] 1990 Optional Kernel mode setting: 1991 kms, kbd format: kms,kbd 1992 kms, kbd and serial format: kms,kbd,<ser_dev>[,baud] 1993 1994 kgdbwait [KGDB] Stop kernel execution and enter the 1995 kernel debugger at the earliest opportunity. 1996 1997 kmac= [MIPS] korina ethernet MAC address. 1998 Configure the RouterBoard 532 series on-chip 1999 Ethernet adapter MAC address. 2000 2001 kmemleak= [KNL] Boot-time kmemleak enable/disable 2002 Valid arguments: on, off 2003 Default: on 2004 Built with CONFIG_DEBUG_KMEMLEAK_DEFAULT_OFF=y, 2005 the default is off. 2006 2007 kpti= [ARM64] Control page table isolation of user 2008 and kernel address spaces. 2009 Default: enabled on cores which need mitigation. 2010 0: force disabled 2011 1: force enabled 2012 2013 kvm.ignore_msrs=[KVM] Ignore guest accesses to unhandled MSRs. 2014 Default is 0 (don't ignore, but inject #GP) 2015 2016 kvm.enable_vmware_backdoor=[KVM] Support VMware backdoor PV interface. 2017 Default is false (don't support). 2018 2019 kvm.mmu_audit= [KVM] This is a R/W parameter which allows audit 2020 KVM MMU at runtime. 2021 Default is 0 (off) 2022 2023 kvm-amd.nested= [KVM,AMD] Allow nested virtualization in KVM/SVM. 2024 Default is 1 (enabled) 2025 2026 kvm-amd.npt= [KVM,AMD] Disable nested paging (virtualized MMU) 2027 for all guests. 2028 Default is 1 (enabled) if in 64-bit or 32-bit PAE mode. 2029 2030 kvm-arm.vgic_v3_group0_trap= 2031 [KVM,ARM] Trap guest accesses to GICv3 group-0 2032 system registers 2033 2034 kvm-arm.vgic_v3_group1_trap= 2035 [KVM,ARM] Trap guest accesses to GICv3 group-1 2036 system registers 2037 2038 kvm-arm.vgic_v3_common_trap= 2039 [KVM,ARM] Trap guest accesses to GICv3 common 2040 system registers 2041 2042 kvm-arm.vgic_v4_enable= 2043 [KVM,ARM] Allow use of GICv4 for direct injection of 2044 LPIs. 2045 2046 kvm-intel.ept= [KVM,Intel] Disable extended page tables 2047 (virtualized MMU) support on capable Intel chips. 2048 Default is 1 (enabled) 2049 2050 kvm-intel.emulate_invalid_guest_state= 2051 [KVM,Intel] Enable emulation of invalid guest states 2052 Default is 0 (disabled) 2053 2054 kvm-intel.flexpriority= 2055 [KVM,Intel] Disable FlexPriority feature (TPR shadow). 2056 Default is 1 (enabled) 2057 2058 kvm-intel.nested= 2059 [KVM,Intel] Enable VMX nesting (nVMX). 2060 Default is 0 (disabled) 2061 2062 kvm-intel.unrestricted_guest= 2063 [KVM,Intel] Disable unrestricted guest feature 2064 (virtualized real and unpaged mode) on capable 2065 Intel chips. Default is 1 (enabled) 2066 2067 kvm-intel.vmentry_l1d_flush=[KVM,Intel] Mitigation for L1 Terminal Fault 2068 CVE-2018-3620. 2069 2070 Valid arguments: never, cond, always 2071 2072 always: L1D cache flush on every VMENTER. 2073 cond: Flush L1D on VMENTER only when the code between 2074 VMEXIT and VMENTER can leak host memory. 2075 never: Disables the mitigation 2076 2077 Default is cond (do L1 cache flush in specific instances) 2078 2079 kvm-intel.vpid= [KVM,Intel] Disable Virtual Processor Identification 2080 feature (tagged TLBs) on capable Intel chips. 2081 Default is 1 (enabled) 2082 2083 l1tf= [X86] Control mitigation of the L1TF vulnerability on 2084 affected CPUs 2085 2086 The kernel PTE inversion protection is unconditionally 2087 enabled and cannot be disabled. 2088 2089 full 2090 Provides all available mitigations for the 2091 L1TF vulnerability. Disables SMT and 2092 enables all mitigations in the 2093 hypervisors, i.e. unconditional L1D flush. 2094 2095 SMT control and L1D flush control via the 2096 sysfs interface is still possible after 2097 boot. Hypervisors will issue a warning 2098 when the first VM is started in a 2099 potentially insecure configuration, 2100 i.e. SMT enabled or L1D flush disabled. 2101 2102 full,force 2103 Same as 'full', but disables SMT and L1D 2104 flush runtime control. Implies the 2105 'nosmt=force' command line option. 2106 (i.e. sysfs control of SMT is disabled.) 2107 2108 flush 2109 Leaves SMT enabled and enables the default 2110 hypervisor mitigation, i.e. conditional 2111 L1D flush. 2112 2113 SMT control and L1D flush control via the 2114 sysfs interface is still possible after 2115 boot. Hypervisors will issue a warning 2116 when the first VM is started in a 2117 potentially insecure configuration, 2118 i.e. SMT enabled or L1D flush disabled. 2119 2120 flush,nosmt 2121 2122 Disables SMT and enables the default 2123 hypervisor mitigation. 2124 2125 SMT control and L1D flush control via the 2126 sysfs interface is still possible after 2127 boot. Hypervisors will issue a warning 2128 when the first VM is started in a 2129 potentially insecure configuration, 2130 i.e. SMT enabled or L1D flush disabled. 2131 2132 flush,nowarn 2133 Same as 'flush', but hypervisors will not 2134 warn when a VM is started in a potentially 2135 insecure configuration. 2136 2137 off 2138 Disables hypervisor mitigations and doesn't 2139 emit any warnings. 2140 It also drops the swap size and available 2141 RAM limit restriction on both hypervisor and 2142 bare metal. 2143 2144 Default is 'flush'. 2145 2146 For details see: Documentation/admin-guide/hw-vuln/l1tf.rst 2147 2148 l2cr= [PPC] 2149 2150 l3cr= [PPC] 2151 2152 lapic [X86-32,APIC] Enable the local APIC even if BIOS 2153 disabled it. 2154 2155 lapic= [x86,APIC] "notscdeadline" Do not use TSC deadline 2156 value for LAPIC timer one-shot implementation. Default 2157 back to the programmable timer unit in the LAPIC. 2158 2159 lapic_timer_c2_ok [X86,APIC] trust the local apic timer 2160 in C2 power state. 2161 2162 libata.dma= [LIBATA] DMA control 2163 libata.dma=0 Disable all PATA and SATA DMA 2164 libata.dma=1 PATA and SATA Disk DMA only 2165 libata.dma=2 ATAPI (CDROM) DMA only 2166 libata.dma=4 Compact Flash DMA only 2167 Combinations also work, so libata.dma=3 enables DMA 2168 for disks and CDROMs, but not CFs. 2169 2170 libata.ignore_hpa= [LIBATA] Ignore HPA limit 2171 libata.ignore_hpa=0 keep BIOS limits (default) 2172 libata.ignore_hpa=1 ignore limits, using full disk 2173 2174 libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume 2175 when set. 2176 Format: <int> 2177 2178 libata.force= [LIBATA] Force configurations. The format is comma 2179 separated list of "[ID:]VAL" where ID is 2180 PORT[.DEVICE]. PORT and DEVICE are decimal numbers 2181 matching port, link or device. Basically, it matches 2182 the ATA ID string printed on console by libata. If 2183 the whole ID part is omitted, the last PORT and DEVICE 2184 values are used. If ID hasn't been specified yet, the 2185 configuration applies to all ports, links and devices. 2186 2187 If only DEVICE is omitted, the parameter applies to 2188 the port and all links and devices behind it. DEVICE 2189 number of 0 either selects the first device or the 2190 first fan-out link behind PMP device. It does not 2191 select the host link. DEVICE number of 15 selects the 2192 host link and device attached to it. 2193 2194 The VAL specifies the configuration to force. As long 2195 as there's no ambiguity shortcut notation is allowed. 2196 For example, both 1.5 and 1.5G would work for 1.5Gbps. 2197 The following configurations can be forced. 2198 2199 * Cable type: 40c, 80c, short40c, unk, ign or sata. 2200 Any ID with matching PORT is used. 2201 2202 * SATA link speed limit: 1.5Gbps or 3.0Gbps. 2203 2204 * Transfer mode: pio[0-7], mwdma[0-4] and udma[0-7]. 2205 udma[/][16,25,33,44,66,100,133] notation is also 2206 allowed. 2207 2208 * [no]ncq: Turn on or off NCQ. 2209 2210 * [no]ncqtrim: Turn off queued DSM TRIM. 2211 2212 * nohrst, nosrst, norst: suppress hard, soft 2213 and both resets. 2214 2215 * rstonce: only attempt one reset during 2216 hot-unplug link recovery 2217 2218 * dump_id: dump IDENTIFY data. 2219 2220 * atapi_dmadir: Enable ATAPI DMADIR bridge support 2221 2222 * disable: Disable this device. 2223 2224 If there are multiple matching configurations changing 2225 the same attribute, the last one is used. 2226 2227 memblock=debug [KNL] Enable memblock debug messages. 2228 2229 load_ramdisk= [RAM] List of ramdisks to load from floppy 2230 See Documentation/blockdev/ramdisk.txt. 2231 2232 lockd.nlm_grace_period=P [NFS] Assign grace period. 2233 Format: <integer> 2234 2235 lockd.nlm_tcpport=N [NFS] Assign TCP port. 2236 Format: <integer> 2237 2238 lockd.nlm_timeout=T [NFS] Assign timeout value. 2239 Format: <integer> 2240 2241 lockd.nlm_udpport=M [NFS] Assign UDP port. 2242 Format: <integer> 2243 2244 locktorture.nreaders_stress= [KNL] 2245 Set the number of locking read-acquisition kthreads. 2246 Defaults to being automatically set based on the 2247 number of online CPUs. 2248 2249 locktorture.nwriters_stress= [KNL] 2250 Set the number of locking write-acquisition kthreads. 2251 2252 locktorture.onoff_holdoff= [KNL] 2253 Set time (s) after boot for CPU-hotplug testing. 2254 2255 locktorture.onoff_interval= [KNL] 2256 Set time (s) between CPU-hotplug operations, or 2257 zero to disable CPU-hotplug testing. 2258 2259 locktorture.shuffle_interval= [KNL] 2260 Set task-shuffle interval (jiffies). Shuffling 2261 tasks allows some CPUs to go into dyntick-idle 2262 mode during the locktorture test. 2263 2264 locktorture.shutdown_secs= [KNL] 2265 Set time (s) after boot system shutdown. This 2266 is useful for hands-off automated testing. 2267 2268 locktorture.stat_interval= [KNL] 2269 Time (s) between statistics printk()s. 2270 2271 locktorture.stutter= [KNL] 2272 Time (s) to stutter testing, for example, 2273 specifying five seconds causes the test to run for 2274 five seconds, wait for five seconds, and so on. 2275 This tests the locking primitive's ability to 2276 transition abruptly to and from idle. 2277 2278 locktorture.torture_type= [KNL] 2279 Specify the locking implementation to test. 2280 2281 locktorture.verbose= [KNL] 2282 Enable additional printk() statements. 2283 2284 logibm.irq= [HW,MOUSE] Logitech Bus Mouse Driver 2285 Format: <irq> 2286 2287 loglevel= All Kernel Messages with a loglevel smaller than the 2288 console loglevel will be printed to the console. It can 2289 also be changed with klogd or other programs. The 2290 loglevels are defined as follows: 2291 2292 0 (KERN_EMERG) system is unusable 2293 1 (KERN_ALERT) action must be taken immediately 2294 2 (KERN_CRIT) critical conditions 2295 3 (KERN_ERR) error conditions 2296 4 (KERN_WARNING) warning conditions 2297 5 (KERN_NOTICE) normal but significant condition 2298 6 (KERN_INFO) informational 2299 7 (KERN_DEBUG) debug-level messages 2300 2301 log_buf_len=n[KMG] Sets the size of the printk ring buffer, 2302 in bytes. n must be a power of two and greater 2303 than the minimal size. The minimal size is defined 2304 by LOG_BUF_SHIFT kernel config parameter. There is 2305 also CONFIG_LOG_CPU_MAX_BUF_SHIFT config parameter 2306 that allows to increase the default size depending on 2307 the number of CPUs. See init/Kconfig for more details. 2308 2309 logo.nologo [FB] Disables display of the built-in Linux logo. 2310 This may be used to provide more screen space for 2311 kernel log messages and is useful when debugging 2312 kernel boot problems. 2313 2314 lp=0 [LP] Specify parallel ports to use, e.g, 2315 lp=port[,port...] lp=none,parport0 (lp0 not configured, lp1 uses 2316 lp=reset first parallel port). 'lp=0' disables the 2317 lp=auto printer driver. 'lp=reset' (which can be 2318 specified in addition to the ports) causes 2319 attached printers to be reset. Using 2320 lp=port1,port2,... specifies the parallel ports 2321 to associate lp devices with, starting with 2322 lp0. A port specification may be 'none' to skip 2323 that lp device, or a parport name such as 2324 'parport0'. Specifying 'lp=auto' instead of a 2325 port specification list means that device IDs 2326 from each port should be examined, to see if 2327 an IEEE 1284-compliant printer is attached; if 2328 so, the driver will manage that printer. 2329 See also header of drivers/char/lp.c. 2330 2331 lpj=n [KNL] 2332 Sets loops_per_jiffy to given constant, thus avoiding 2333 time-consuming boot-time autodetection (up to 250 ms per 2334 CPU). 0 enables autodetection (default). To determine 2335 the correct value for your kernel, boot with normal 2336 autodetection and see what value is printed. Note that 2337 on SMP systems the preset will be applied to all CPUs, 2338 which is likely to cause problems if your CPUs need 2339 significantly divergent settings. An incorrect value 2340 will cause delays in the kernel to be wrong, leading to 2341 unpredictable I/O errors and other breakage. Although 2342 unlikely, in the extreme case this might damage your 2343 hardware. 2344 2345 ltpc= [NET] 2346 Format: <io>,<irq>,<dma> 2347 2348 lsm.debug [SECURITY] Enable LSM initialization debugging output. 2349 2350 lsm=lsm1,...,lsmN 2351 [SECURITY] Choose order of LSM initialization. This 2352 overrides CONFIG_LSM, and the "security=" parameter. 2353 2354 machvec= [IA-64] Force the use of a particular machine-vector 2355 (machvec) in a generic kernel. 2356 Example: machvec=hpzx1_swiotlb 2357 2358 machtype= [Loongson] Share the same kernel image file between different 2359 yeeloong laptop. 2360 Example: machtype=lemote-yeeloong-2f-7inch 2361 2362 max_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory greater 2363 than or equal to this physical address is ignored. 2364 2365 maxcpus= [SMP] Maximum number of processors that an SMP kernel 2366 will bring up during bootup. maxcpus=n : n >= 0 limits 2367 the kernel to bring up 'n' processors. Surely after 2368 bootup you can bring up the other plugged cpu by executing 2369 "echo 1 > /sys/devices/system/cpu/cpuX/online". So maxcpus 2370 only takes effect during system bootup. 2371 While n=0 is a special case, it is equivalent to "nosmp", 2372 which also disables the IO APIC. 2373 2374 max_loop= [LOOP] The number of loop block devices that get 2375 (loop.max_loop) unconditionally pre-created at init time. The default 2376 number is configured by BLK_DEV_LOOP_MIN_COUNT. Instead 2377 of statically allocating a predefined number, loop 2378 devices can be requested on-demand with the 2379 /dev/loop-control interface. 2380 2381 mce [X86-32] Machine Check Exception 2382 2383 mce=option [X86-64] See Documentation/x86/x86_64/boot-options.rst 2384 2385 md= [HW] RAID subsystems devices and level 2386 See Documentation/admin-guide/md.rst. 2387 2388 mdacon= [MDA] 2389 Format: <first>,<last> 2390 Specifies range of consoles to be captured by the MDA. 2391 2392 mds= [X86,INTEL] 2393 Control mitigation for the Micro-architectural Data 2394 Sampling (MDS) vulnerability. 2395 2396 Certain CPUs are vulnerable to an exploit against CPU 2397 internal buffers which can forward information to a 2398 disclosure gadget under certain conditions. 2399 2400 In vulnerable processors, the speculatively 2401 forwarded data can be used in a cache side channel 2402 attack, to access data to which the attacker does 2403 not have direct access. 2404 2405 This parameter controls the MDS mitigation. The 2406 options are: 2407 2408 full - Enable MDS mitigation on vulnerable CPUs 2409 full,nosmt - Enable MDS mitigation and disable 2410 SMT on vulnerable CPUs 2411 off - Unconditionally disable MDS mitigation 2412 2413 Not specifying this option is equivalent to 2414 mds=full. 2415 2416 For details see: Documentation/admin-guide/hw-vuln/mds.rst 2417 2418 mem=nn[KMG] [KNL,BOOT] Force usage of a specific amount of memory 2419 Amount of memory to be used when the kernel is not able 2420 to see the whole system memory or for test. 2421 [X86] Work as limiting max address. Use together 2422 with memmap= to avoid physical address space collisions. 2423 Without memmap= PCI devices could be placed at addresses 2424 belonging to unused RAM. 2425 2426 mem=nopentium [BUGS=X86-32] Disable usage of 4MB pages for kernel 2427 memory. 2428 2429 memchunk=nn[KMG] 2430 [KNL,SH] Allow user to override the default size for 2431 per-device physically contiguous DMA buffers. 2432 2433 memhp_default_state=online/offline 2434 [KNL] Set the initial state for the memory hotplug 2435 onlining policy. If not specified, the default value is 2436 set according to the 2437 CONFIG_MEMORY_HOTPLUG_DEFAULT_ONLINE kernel config 2438 option. 2439 See Documentation/admin-guide/mm/memory-hotplug.rst. 2440 2441 memmap=exactmap [KNL,X86] Enable setting of an exact 2442 E820 memory map, as specified by the user. 2443 Such memmap=exactmap lines can be constructed based on 2444 BIOS output or other requirements. See the memmap=nn@ss 2445 option description. 2446 2447 memmap=nn[KMG]@ss[KMG] 2448 [KNL] Force usage of a specific region of memory. 2449 Region of memory to be used is from ss to ss+nn. 2450 If @ss[KMG] is omitted, it is equivalent to mem=nn[KMG], 2451 which limits max address to nn[KMG]. 2452 Multiple different regions can be specified, 2453 comma delimited. 2454 Example: 2455 memmap=100M@2G,100M#3G,1G!1024G 2456 2457 memmap=nn[KMG]#ss[KMG] 2458 [KNL,ACPI] Mark specific memory as ACPI data. 2459 Region of memory to be marked is from ss to ss+nn. 2460 2461 memmap=nn[KMG]$ss[KMG] 2462 [KNL,ACPI] Mark specific memory as reserved. 2463 Region of memory to be reserved is from ss to ss+nn. 2464 Example: Exclude memory from 0x18690000-0x1869ffff 2465 memmap=64K$0x18690000 2466 or 2467 memmap=0x10000$0x18690000 2468 Some bootloaders may need an escape character before '$', 2469 like Grub2, otherwise '$' and the following number 2470 will be eaten. 2471 2472 memmap=nn[KMG]!ss[KMG] 2473 [KNL,X86] Mark specific memory as protected. 2474 Region of memory to be used, from ss to ss+nn. 2475 The memory region may be marked as e820 type 12 (0xc) 2476 and is NVDIMM or ADR memory. 2477 2478 memmap=<size>%<offset>-<oldtype>+<newtype> 2479 [KNL,ACPI] Convert memory within the specified region 2480 from <oldtype> to <newtype>. If "-<oldtype>" is left 2481 out, the whole region will be marked as <newtype>, 2482 even if previously unavailable. If "+<newtype>" is left 2483 out, matching memory will be removed. Types are 2484 specified as e820 types, e.g., 1 = RAM, 2 = reserved, 2485 3 = ACPI, 12 = PRAM. 2486 2487 memory_corruption_check=0/1 [X86] 2488 Some BIOSes seem to corrupt the first 64k of 2489 memory when doing things like suspend/resume. 2490 Setting this option will scan the memory 2491 looking for corruption. Enabling this will 2492 both detect corruption and prevent the kernel 2493 from using the memory being corrupted. 2494 However, its intended as a diagnostic tool; if 2495 repeatable BIOS-originated corruption always 2496 affects the same memory, you can use memmap= 2497 to prevent the kernel from using that memory. 2498 2499 memory_corruption_check_size=size [X86] 2500 By default it checks for corruption in the low 2501 64k, making this memory unavailable for normal 2502 use. Use this parameter to scan for 2503 corruption in more or less memory. 2504 2505 memory_corruption_check_period=seconds [X86] 2506 By default it checks for corruption every 60 2507 seconds. Use this parameter to check at some 2508 other rate. 0 disables periodic checking. 2509 2510 memtest= [KNL,X86,ARM,PPC] Enable memtest 2511 Format: <integer> 2512 default : 0 <disable> 2513 Specifies the number of memtest passes to be 2514 performed. Each pass selects another test 2515 pattern from a given set of patterns. Memtest 2516 fills the memory with this pattern, validates 2517 memory contents and reserves bad memory 2518 regions that are detected. 2519 2520 mem_encrypt= [X86-64] AMD Secure Memory Encryption (SME) control 2521 Valid arguments: on, off 2522 Default (depends on kernel configuration option): 2523 on (CONFIG_AMD_MEM_ENCRYPT_ACTIVE_BY_DEFAULT=y) 2524 off (CONFIG_AMD_MEM_ENCRYPT_ACTIVE_BY_DEFAULT=n) 2525 mem_encrypt=on: Activate SME 2526 mem_encrypt=off: Do not activate SME 2527 2528 Refer to Documentation/virtual/kvm/amd-memory-encryption.rst 2529 for details on when memory encryption can be activated. 2530 2531 mem_sleep_default= [SUSPEND] Default system suspend mode: 2532 s2idle - Suspend-To-Idle 2533 shallow - Power-On Suspend or equivalent (if supported) 2534 deep - Suspend-To-RAM or equivalent (if supported) 2535 See Documentation/admin-guide/pm/sleep-states.rst. 2536 2537 meye.*= [HW] Set MotionEye Camera parameters 2538 See Documentation/media/v4l-drivers/meye.rst. 2539 2540 mfgpt_irq= [IA-32] Specify the IRQ to use for the 2541 Multi-Function General Purpose Timers on AMD Geode 2542 platforms. 2543 2544 mfgptfix [X86-32] Fix MFGPT timers on AMD Geode platforms when 2545 the BIOS has incorrectly applied a workaround. TinyBIOS 2546 version 0.98 is known to be affected, 0.99 fixes the 2547 problem by letting the user disable the workaround. 2548 2549 mga= [HW,DRM] 2550 2551 min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this 2552 physical address is ignored. 2553 2554 mini2440= [ARM,HW,KNL] 2555 Format:[0..2][b][c][t] 2556 Default: "0tb" 2557 MINI2440 configuration specification: 2558 0 - The attached screen is the 3.5" TFT 2559 1 - The attached screen is the 7" TFT 2560 2 - The VGA Shield is attached (1024x768) 2561 Leaving out the screen size parameter will not load 2562 the TFT driver, and the framebuffer will be left 2563 unconfigured. 2564 b - Enable backlight. The TFT backlight pin will be 2565 linked to the kernel VESA blanking code and a GPIO 2566 LED. This parameter is not necessary when using the 2567 VGA shield. 2568 c - Enable the s3c camera interface. 2569 t - Reserved for enabling touchscreen support. The 2570 touchscreen support is not enabled in the mainstream 2571 kernel as of 2.6.30, a preliminary port can be found 2572 in the "bleeding edge" mini2440 support kernel at 2573 http://repo.or.cz/w/linux-2.6/mini2440.git 2574 2575 mitigations= 2576 [X86,PPC,S390,ARM64] Control optional mitigations for 2577 CPU vulnerabilities. This is a set of curated, 2578 arch-independent options, each of which is an 2579 aggregation of existing arch-specific options. 2580 2581 off 2582 Disable all optional CPU mitigations. This 2583 improves system performance, but it may also 2584 expose users to several CPU vulnerabilities. 2585 Equivalent to: nopti [X86,PPC] 2586 kpti=0 [ARM64] 2587 nospectre_v1 [PPC] 2588 nobp=0 [S390] 2589 nospectre_v2 [X86,PPC,S390,ARM64] 2590 spectre_v2_user=off [X86] 2591 spec_store_bypass_disable=off [X86,PPC] 2592 ssbd=force-off [ARM64] 2593 l1tf=off [X86] 2594 mds=off [X86] 2595 2596 auto (default) 2597 Mitigate all CPU vulnerabilities, but leave SMT 2598 enabled, even if it's vulnerable. This is for 2599 users who don't want to be surprised by SMT 2600 getting disabled across kernel upgrades, or who 2601 have other ways of avoiding SMT-based attacks. 2602 Equivalent to: (default behavior) 2603 2604 auto,nosmt 2605 Mitigate all CPU vulnerabilities, disabling SMT 2606 if needed. This is for users who always want to 2607 be fully mitigated, even if it means losing SMT. 2608 Equivalent to: l1tf=flush,nosmt [X86] 2609 mds=full,nosmt [X86] 2610 2611 mminit_loglevel= 2612 [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this 2613 parameter allows control of the logging verbosity for 2614 the additional memory initialisation checks. A value 2615 of 0 disables mminit logging and a level of 4 will 2616 log everything. Information is printed at KERN_DEBUG 2617 so loglevel=8 may also need to be specified. 2618 2619 module.sig_enforce 2620 [KNL] When CONFIG_MODULE_SIG is set, this means that 2621 modules without (valid) signatures will fail to load. 2622 Note that if CONFIG_MODULE_SIG_FORCE is set, that 2623 is always true, so this option does nothing. 2624 2625 module_blacklist= [KNL] Do not load a comma-separated list of 2626 modules. Useful for debugging problem modules. 2627 2628 mousedev.tap_time= 2629 [MOUSE] Maximum time between finger touching and 2630 leaving touchpad surface for touch to be considered 2631 a tap and be reported as a left button click (for 2632 touchpads working in absolute mode only). 2633 Format: <msecs> 2634 mousedev.xres= [MOUSE] Horizontal screen resolution, used for devices 2635 reporting absolute coordinates, such as tablets 2636 mousedev.yres= [MOUSE] Vertical screen resolution, used for devices 2637 reporting absolute coordinates, such as tablets 2638 2639 movablecore= [KNL,X86,IA-64,PPC] 2640 Format: nn[KMGTPE] | nn% 2641 This parameter is the complement to kernelcore=, it 2642 specifies the amount of memory used for migratable 2643 allocations. If both kernelcore and movablecore is 2644 specified, then kernelcore will be at *least* the 2645 specified value but may be more. If movablecore on its 2646 own is specified, the administrator must be careful 2647 that the amount of memory usable for all allocations 2648 is not too small. 2649 2650 movable_node [KNL] Boot-time switch to make hotplugable memory 2651 NUMA nodes to be movable. This means that the memory 2652 of such nodes will be usable only for movable 2653 allocations which rules out almost all kernel 2654 allocations. Use with caution! 2655 2656 MTD_Partition= [MTD] 2657 Format: <name>,<region-number>,<size>,<offset> 2658 2659 MTD_Region= [MTD] Format: 2660 <name>,<region-number>[,<base>,<size>,<buswidth>,<altbuswidth>] 2661 2662 mtdparts= [MTD] 2663 See drivers/mtd/cmdlinepart.c. 2664 2665 multitce=off [PPC] This parameter disables the use of the pSeries 2666 firmware feature for updating multiple TCE entries 2667 at a time. 2668 2669 onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration 2670 2671 Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock] 2672 2673 boundary - index of last SLC block on Flex-OneNAND. 2674 The remaining blocks are configured as MLC blocks. 2675 lock - Configure if Flex-OneNAND boundary should be locked. 2676 Once locked, the boundary cannot be changed. 2677 1 indicates lock status, 0 indicates unlock status. 2678 2679 mtdset= [ARM] 2680 ARM/S3C2412 JIVE boot control 2681 2682 See arch/arm/mach-s3c2412/mach-jive.c 2683 2684 mtouchusb.raw_coordinates= 2685 [HW] Make the MicroTouch USB driver use raw coordinates 2686 ('y', default) or cooked coordinates ('n') 2687 2688 mtrr_chunk_size=nn[KMG] [X86] 2689 used for mtrr cleanup. It is largest continuous chunk 2690 that could hold holes aka. UC entries. 2691 2692 mtrr_gran_size=nn[KMG] [X86] 2693 Used for mtrr cleanup. It is granularity of mtrr block. 2694 Default is 1. 2695 Large value could prevent small alignment from 2696 using up MTRRs. 2697 2698 mtrr_spare_reg_nr=n [X86] 2699 Format: <integer> 2700 Range: 0,7 : spare reg number 2701 Default : 1 2702 Used for mtrr cleanup. It is spare mtrr entries number. 2703 Set to 2 or more if your graphical card needs more. 2704 2705 n2= [NET] SDL Inc. RISCom/N2 synchronous serial card 2706 2707 netdev= [NET] Network devices parameters 2708 Format: <irq>,<io>,<mem_start>,<mem_end>,<name> 2709 Note that mem_start is often overloaded to mean 2710 something different and driver-specific. 2711 This usage is only documented in each driver source 2712 file if at all. 2713 2714 nf_conntrack.acct= 2715 [NETFILTER] Enable connection tracking flow accounting 2716 0 to disable accounting 2717 1 to enable accounting 2718 Default value is 0. 2719 2720 nfsaddrs= [NFS] Deprecated. Use ip= instead. 2721 See Documentation/filesystems/nfs/nfsroot.txt. 2722 2723 nfsroot= [NFS] nfs root filesystem for disk-less boxes. 2724 See Documentation/filesystems/nfs/nfsroot.txt. 2725 2726 nfsrootdebug [NFS] enable nfsroot debugging messages. 2727 See Documentation/filesystems/nfs/nfsroot.txt. 2728 2729 nfs.callback_nr_threads= 2730 [NFSv4] set the total number of threads that the 2731 NFS client will assign to service NFSv4 callback 2732 requests. 2733 2734 nfs.callback_tcpport= 2735 [NFS] set the TCP port on which the NFSv4 callback 2736 channel should listen. 2737 2738 nfs.cache_getent= 2739 [NFS] sets the pathname to the program which is used 2740 to update the NFS client cache entries. 2741 2742 nfs.cache_getent_timeout= 2743 [NFS] sets the timeout after which an attempt to 2744 update a cache entry is deemed to have failed. 2745 2746 nfs.idmap_cache_timeout= 2747 [NFS] set the maximum lifetime for idmapper cache 2748 entries. 2749 2750 nfs.enable_ino64= 2751 [NFS] enable 64-bit inode numbers. 2752 If zero, the NFS client will fake up a 32-bit inode 2753 number for the readdir() and stat() syscalls instead 2754 of returning the full 64-bit number. 2755 The default is to return 64-bit inode numbers. 2756 2757 nfs.max_session_cb_slots= 2758 [NFSv4.1] Sets the maximum number of session 2759 slots the client will assign to the callback 2760 channel. This determines the maximum number of 2761 callbacks the client will process in parallel for 2762 a particular server. 2763 2764 nfs.max_session_slots= 2765 [NFSv4.1] Sets the maximum number of session slots 2766 the client will attempt to negotiate with the server. 2767 This limits the number of simultaneous RPC requests 2768 that the client can send to the NFSv4.1 server. 2769 Note that there is little point in setting this 2770 value higher than the max_tcp_slot_table_limit. 2771 2772 nfs.nfs4_disable_idmapping= 2773 [NFSv4] When set to the default of '1', this option 2774 ensures that both the RPC level authentication 2775 scheme and the NFS level operations agree to use 2776 numeric uids/gids if the mount is using the 2777 'sec=sys' security flavour. In effect it is 2778 disabling idmapping, which can make migration from 2779 legacy NFSv2/v3 systems to NFSv4 easier. 2780 Servers that do not support this mode of operation 2781 will be autodetected by the client, and it will fall 2782 back to using the idmapper. 2783 To turn off this behaviour, set the value to '0'. 2784 nfs.nfs4_unique_id= 2785 [NFS4] Specify an additional fixed unique ident- 2786 ification string that NFSv4 clients can insert into 2787 their nfs_client_id4 string. This is typically a 2788 UUID that is generated at system install time. 2789 2790 nfs.send_implementation_id = 2791 [NFSv4.1] Send client implementation identification 2792 information in exchange_id requests. 2793 If zero, no implementation identification information 2794 will be sent. 2795 The default is to send the implementation identification 2796 information. 2797 2798 nfs.recover_lost_locks = 2799 [NFSv4] Attempt to recover locks that were lost due 2800 to a lease timeout on the server. Please note that 2801 doing this risks data corruption, since there are 2802 no guarantees that the file will remain unchanged 2803 after the locks are lost. 2804 If you want to enable the kernel legacy behaviour of 2805 attempting to recover these locks, then set this 2806 parameter to '1'. 2807 The default parameter value of '0' causes the kernel 2808 not to attempt recovery of lost locks. 2809 2810 nfs4.layoutstats_timer = 2811 [NFSv4.2] Change the rate at which the kernel sends 2812 layoutstats to the pNFS metadata server. 2813 2814 Setting this to value to 0 causes the kernel to use 2815 whatever value is the default set by the layout 2816 driver. A non-zero value sets the minimum interval 2817 in seconds between layoutstats transmissions. 2818 2819 nfsd.nfs4_disable_idmapping= 2820 [NFSv4] When set to the default of '1', the NFSv4 2821 server will return only numeric uids and gids to 2822 clients using auth_sys, and will accept numeric uids 2823 and gids from such clients. This is intended to ease 2824 migration from NFSv2/v3. 2825 2826 nmi_debug= [KNL,SH] Specify one or more actions to take 2827 when a NMI is triggered. 2828 Format: [state][,regs][,debounce][,die] 2829 2830 nmi_watchdog= [KNL,BUGS=X86] Debugging features for SMP kernels 2831 Format: [panic,][nopanic,][num] 2832 Valid num: 0 or 1 2833 0 - turn hardlockup detector in nmi_watchdog off 2834 1 - turn hardlockup detector in nmi_watchdog on 2835 When panic is specified, panic when an NMI watchdog 2836 timeout occurs (or 'nopanic' to not panic on an NMI 2837 watchdog, if CONFIG_BOOTPARAM_HARDLOCKUP_PANIC is set) 2838 To disable both hard and soft lockup detectors, 2839 please see 'nowatchdog'. 2840 This is useful when you use a panic=... timeout and 2841 need the box quickly up again. 2842 2843 These settings can be accessed at runtime via 2844 the nmi_watchdog and hardlockup_panic sysctls. 2845 2846 netpoll.carrier_timeout= 2847 [NET] Specifies amount of time (in seconds) that 2848 netpoll should wait for a carrier. By default netpoll 2849 waits 4 seconds. 2850 2851 no387 [BUGS=X86-32] Tells the kernel to use the 387 maths 2852 emulation library even if a 387 maths coprocessor 2853 is present. 2854 2855 no5lvl [X86-64] Disable 5-level paging mode. Forces 2856 kernel to use 4-level paging instead. 2857 2858 no_console_suspend 2859 [HW] Never suspend the console 2860 Disable suspending of consoles during suspend and 2861 hibernate operations. Once disabled, debugging 2862 messages can reach various consoles while the rest 2863 of the system is being put to sleep (ie, while 2864 debugging driver suspend/resume hooks). This may 2865 not work reliably with all consoles, but is known 2866 to work with serial and VGA consoles. 2867 To facilitate more flexible debugging, we also add 2868 console_suspend, a printk module parameter to control 2869 it. Users could use console_suspend (usually 2870 /sys/module/printk/parameters/console_suspend) to 2871 turn on/off it dynamically. 2872 2873 noaliencache [MM, NUMA, SLAB] Disables the allocation of alien 2874 caches in the slab allocator. Saves per-node memory, 2875 but will impact performance. 2876 2877 noalign [KNL,ARM] 2878 2879 noaltinstr [S390] Disables alternative instructions patching 2880 (CPU alternatives feature). 2881 2882 noapic [SMP,APIC] Tells the kernel to not make use of any 2883 IOAPICs that may be present in the system. 2884 2885 noautogroup Disable scheduler automatic task group creation. 2886 2887 nobats [PPC] Do not use BATs for mapping kernel lowmem 2888 on "Classic" PPC cores. 2889 2890 nocache [ARM] 2891 2892 noclflush [BUGS=X86] Don't use the CLFLUSH instruction 2893 2894 nodelayacct [KNL] Disable per-task delay accounting 2895 2896 nodsp [SH] Disable hardware DSP at boot time. 2897 2898 noefi Disable EFI runtime services support. 2899 2900 noexec [IA-64] 2901 2902 noexec [X86] 2903 On X86-32 available only on PAE configured kernels. 2904 noexec=on: enable non-executable mappings (default) 2905 noexec=off: disable non-executable mappings 2906 2907 nosmap [X86,PPC] 2908 Disable SMAP (Supervisor Mode Access Prevention) 2909 even if it is supported by processor. 2910 2911 nosmep [X86,PPC] 2912 Disable SMEP (Supervisor Mode Execution Prevention) 2913 even if it is supported by processor. 2914 2915 noexec32 [X86-64] 2916 This affects only 32-bit executables. 2917 noexec32=on: enable non-executable mappings (default) 2918 read doesn't imply executable mappings 2919 noexec32=off: disable non-executable mappings 2920 read implies executable mappings 2921 2922 nofpu [MIPS,SH] Disable hardware FPU at boot time. 2923 2924 nofxsr [BUGS=X86-32] Disables x86 floating point extended 2925 register save and restore. The kernel will only save 2926 legacy floating-point registers on task switch. 2927 2928 nohugeiomap [KNL,x86] Disable kernel huge I/O mappings. 2929 2930 nosmt [KNL,S390] Disable symmetric multithreading (SMT). 2931 Equivalent to smt=1. 2932 2933 [KNL,x86] Disable symmetric multithreading (SMT). 2934 nosmt=force: Force disable SMT, cannot be undone 2935 via the sysfs control file. 2936 2937 nospectre_v1 [PPC] Disable mitigations for Spectre Variant 1 (bounds 2938 check bypass). With this option data leaks are possible 2939 in the system. 2940 2941 nospectre_v2 [X86,PPC_FSL_BOOK3E,ARM64] Disable all mitigations for 2942 the Spectre variant 2 (indirect branch prediction) 2943 vulnerability. System may allow data leaks with this 2944 option. 2945 2946 nospec_store_bypass_disable 2947 [HW] Disable all mitigations for the Speculative Store Bypass vulnerability 2948 2949 noxsave [BUGS=X86] Disables x86 extended register state save 2950 and restore using xsave. The kernel will fallback to 2951 enabling legacy floating-point and sse state. 2952 2953 noxsaveopt [X86] Disables xsaveopt used in saving x86 extended 2954 register states. The kernel will fall back to use 2955 xsave to save the states. By using this parameter, 2956 performance of saving the states is degraded because 2957 xsave doesn't support modified optimization while 2958 xsaveopt supports it on xsaveopt enabled systems. 2959 2960 noxsaves [X86] Disables xsaves and xrstors used in saving and 2961 restoring x86 extended register state in compacted 2962 form of xsave area. The kernel will fall back to use 2963 xsaveopt and xrstor to save and restore the states 2964 in standard form of xsave area. By using this 2965 parameter, xsave area per process might occupy more 2966 memory on xsaves enabled systems. 2967 2968 nohlt [BUGS=ARM,SH] Tells the kernel that the sleep(SH) or 2969 wfi(ARM) instruction doesn't work correctly and not to 2970 use it. This is also useful when using JTAG debugger. 2971 2972 no_file_caps Tells the kernel not to honor file capabilities. The 2973 only way then for a file to be executed with privilege 2974 is to be setuid root or executed by root. 2975 2976 nohalt [IA-64] Tells the kernel not to use the power saving 2977 function PAL_HALT_LIGHT when idle. This increases 2978 power-consumption. On the positive side, it reduces 2979 interrupt wake-up latency, which may improve performance 2980 in certain environments such as networked servers or 2981 real-time systems. 2982 2983 nohibernate [HIBERNATION] Disable hibernation and resume. 2984 2985 nohz= [KNL] Boottime enable/disable dynamic ticks 2986 Valid arguments: on, off 2987 Default: on 2988 2989 nohz_full= [KNL,BOOT,SMP,ISOL] 2990 The argument is a cpu list, as described above. 2991 In kernels built with CONFIG_NO_HZ_FULL=y, set 2992 the specified list of CPUs whose tick will be stopped 2993 whenever possible. The boot CPU will be forced outside 2994 the range to maintain the timekeeping. Any CPUs 2995 in this list will have their RCU callbacks offloaded, 2996 just as if they had also been called out in the 2997 rcu_nocbs= boot parameter. 2998 2999 noiotrap [SH] Disables trapped I/O port accesses. 3000 3001 noirqdebug [X86-32] Disables the code which attempts to detect and 3002 disable unhandled interrupt sources. 3003 3004 no_timer_check [X86,APIC] Disables the code which tests for 3005 broken timer IRQ sources. 3006 3007 noisapnp [ISAPNP] Disables ISA PnP code. 3008 3009 noinitrd [RAM] Tells the kernel not to load any configured 3010 initial RAM disk. 3011 3012 nointremap [X86-64, Intel-IOMMU] Do not enable interrupt 3013 remapping. 3014 [Deprecated - use intremap=off] 3015 3016 nointroute [IA-64] 3017 3018 noinvpcid [X86] Disable the INVPCID cpu feature. 3019 3020 nojitter [IA-64] Disables jitter checking for ITC timers. 3021 3022 no-kvmclock [X86,KVM] Disable paravirtualized KVM clock driver 3023 3024 no-kvmapf [X86,KVM] Disable paravirtualized asynchronous page 3025 fault handling. 3026 3027 no-vmw-sched-clock 3028 [X86,PV_OPS] Disable paravirtualized VMware scheduler 3029 clock and use the default one. 3030 3031 no-steal-acc [X86,KVM] Disable paravirtualized steal time accounting. 3032 steal time is computed, but won't influence scheduler 3033 behaviour 3034 3035 nolapic [X86-32,APIC] Do not enable or use the local APIC. 3036 3037 nolapic_timer [X86-32,APIC] Do not use the local APIC timer. 3038 3039 noltlbs [PPC] Do not use large page/tlb entries for kernel 3040 lowmem mapping on PPC40x and PPC8xx 3041 3042 nomca [IA-64] Disable machine check abort handling 3043 3044 nomce [X86-32] Disable Machine Check Exception 3045 3046 nomfgpt [X86-32] Disable Multi-Function General Purpose 3047 Timer usage (for AMD Geode machines). 3048 3049 nonmi_ipi [X86] Disable using NMI IPIs during panic/reboot to 3050 shutdown the other cpus. Instead use the REBOOT_VECTOR 3051 irq. 3052 3053 nomodule Disable module load 3054 3055 nopat [X86] Disable PAT (page attribute table extension of 3056 pagetables) support. 3057 3058 nopcid [X86-64] Disable the PCID cpu feature. 3059 3060 norandmaps Don't use address space randomization. Equivalent to 3061 echo 0 > /proc/sys/kernel/randomize_va_space 3062 3063 noreplace-smp [X86-32,SMP] Don't replace SMP instructions 3064 with UP alternatives 3065 3066 nordrand [X86] Disable kernel use of the RDRAND and 3067 RDSEED instructions even if they are supported 3068 by the processor. RDRAND and RDSEED are still 3069 available to user space applications. 3070 3071 noresume [SWSUSP] Disables resume and restores original swap 3072 space. 3073 3074 no-scroll [VGA] Disables scrollback. 3075 This is required for the Braillex ib80-piezo Braille 3076 reader made by F.H. Papenmeier (Germany). 3077 3078 nosbagart [IA-64] 3079 3080 nosep [BUGS=X86-32] Disables x86 SYSENTER/SYSEXIT support. 3081 3082 nosmp [SMP] Tells an SMP kernel to act as a UP kernel, 3083 and disable the IO APIC. legacy for "maxcpus=0". 3084 3085 nosoftlockup [KNL] Disable the soft-lockup detector. 3086 3087 nosync [HW,M68K] Disables sync negotiation for all devices. 3088 3089 nowatchdog [KNL] Disable both lockup detectors, i.e. 3090 soft-lockup and NMI watchdog (hard-lockup). 3091 3092 nowb [ARM] 3093 3094 nox2apic [X86-64,APIC] Do not enable x2APIC mode. 3095 3096 cpu0_hotplug [X86] Turn on CPU0 hotplug feature when 3097 CONFIG_BOOTPARAM_HOTPLUG_CPU0 is off. 3098 Some features depend on CPU0. Known dependencies are: 3099 1. Resume from suspend/hibernate depends on CPU0. 3100 Suspend/hibernate will fail if CPU0 is offline and you 3101 need to online CPU0 before suspend/hibernate. 3102 2. PIC interrupts also depend on CPU0. CPU0 can't be 3103 removed if a PIC interrupt is detected. 3104 It's said poweroff/reboot may depend on CPU0 on some 3105 machines although I haven't seen such issues so far 3106 after CPU0 is offline on a few tested machines. 3107 If the dependencies are under your control, you can 3108 turn on cpu0_hotplug. 3109 3110 nps_mtm_hs_ctr= [KNL,ARC] 3111 This parameter sets the maximum duration, in 3112 cycles, each HW thread of the CTOP can run 3113 without interruptions, before HW switches it. 3114 The actual maximum duration is 16 times this 3115 parameter's value. 3116 Format: integer between 1 and 255 3117 Default: 255 3118 3119 nptcg= [IA-64] Override max number of concurrent global TLB 3120 purges which is reported from either PAL_VM_SUMMARY or 3121 SAL PALO. 3122 3123 nr_cpus= [SMP] Maximum number of processors that an SMP kernel 3124 could support. nr_cpus=n : n >= 1 limits the kernel to 3125 support 'n' processors. It could be larger than the 3126 number of already plugged CPU during bootup, later in 3127 runtime you can physically add extra cpu until it reaches 3128 n. So during boot up some boot time memory for per-cpu 3129 variables need be pre-allocated for later physical cpu 3130 hot plugging. 3131 3132 nr_uarts= [SERIAL] maximum number of UARTs to be registered. 3133 3134 numa_balancing= [KNL,X86] Enable or disable automatic NUMA balancing. 3135 Allowed values are enable and disable 3136 3137 numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA. 3138 'node', 'default' can be specified 3139 This can be set from sysctl after boot. 3140 See Documentation/sysctl/vm.txt for details. 3141 3142 ohci1394_dma=early [HW] enable debugging via the ohci1394 driver. 3143 See Documentation/debugging-via-ohci1394.txt for more 3144 info. 3145 3146 olpc_ec_timeout= [OLPC] ms delay when issuing EC commands 3147 Rather than timing out after 20 ms if an EC 3148 command is not properly ACKed, override the length 3149 of the timeout. We have interrupts disabled while 3150 waiting for the ACK, so if this is set too high 3151 interrupts *may* be lost! 3152 3153 omap_mux= [OMAP] Override bootloader pin multiplexing. 3154 Format: <mux_mode0.mode_name=value>... 3155 For example, to override I2C bus2: 3156 omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100 3157 3158 oprofile.timer= [HW] 3159 Use timer interrupt instead of performance counters 3160 3161 oprofile.cpu_type= Force an oprofile cpu type 3162 This might be useful if you have an older oprofile 3163 userland or if you want common events. 3164 Format: { arch_perfmon } 3165 arch_perfmon: [X86] Force use of architectural 3166 perfmon on Intel CPUs instead of the 3167 CPU specific event set. 3168 timer: [X86] Force use of architectural NMI 3169 timer mode (see also oprofile.timer 3170 for generic hr timer mode) 3171 3172 oops=panic Always panic on oopses. Default is to just kill the 3173 process, but there is a small probability of 3174 deadlocking the machine. 3175 This will also cause panics on machine check exceptions. 3176 Useful together with panic=30 to trigger a reboot. 3177 3178 page_alloc.shuffle= 3179 [KNL] Boolean flag to control whether the page allocator 3180 should randomize its free lists. The randomization may 3181 be automatically enabled if the kernel detects it is 3182 running on a platform with a direct-mapped memory-side 3183 cache, and this parameter can be used to 3184 override/disable that behavior. The state of the flag 3185 can be read from sysfs at: 3186 /sys/module/page_alloc/parameters/shuffle. 3187 3188 page_owner= [KNL] Boot-time page_owner enabling option. 3189 Storage of the information about who allocated 3190 each page is disabled in default. With this switch, 3191 we can turn it on. 3192 on: enable the feature 3193 3194 page_poison= [KNL] Boot-time parameter changing the state of 3195 poisoning on the buddy allocator, available with 3196 CONFIG_PAGE_POISONING=y. 3197 off: turn off poisoning (default) 3198 on: turn on poisoning 3199 3200 panic= [KNL] Kernel behaviour on panic: delay <timeout> 3201 timeout > 0: seconds before rebooting 3202 timeout = 0: wait forever 3203 timeout < 0: reboot immediately 3204 Format: <timeout> 3205 3206 panic_print= Bitmask for printing system info when panic happens. 3207 User can chose combination of the following bits: 3208 bit 0: print all tasks info 3209 bit 1: print system memory info 3210 bit 2: print timer info 3211 bit 3: print locks info if CONFIG_LOCKDEP is on 3212 bit 4: print ftrace buffer 3213 bit 5: print all printk messages in buffer 3214 3215 panic_on_warn panic() instead of WARN(). Useful to cause kdump 3216 on a WARN(). 3217 3218 crash_kexec_post_notifiers 3219 Run kdump after running panic-notifiers and dumping 3220 kmsg. This only for the users who doubt kdump always 3221 succeeds in any situation. 3222 Note that this also increases risks of kdump failure, 3223 because some panic notifiers can make the crashed 3224 kernel more unstable. 3225 3226 parkbd.port= [HW] Parallel port number the keyboard adapter is 3227 connected to, default is 0. 3228 Format: <parport#> 3229 parkbd.mode= [HW] Parallel port keyboard adapter mode of operation, 3230 0 for XT, 1 for AT (default is AT). 3231 Format: <mode> 3232 3233 parport= [HW,PPT] Specify parallel ports. 0 disables. 3234 Format: { 0 | auto | 0xBBB[,IRQ[,DMA]] } 3235 Use 'auto' to force the driver to use any 3236 IRQ/DMA settings detected (the default is to 3237 ignore detected IRQ/DMA settings because of 3238 possible conflicts). You can specify the base 3239 address, IRQ, and DMA settings; IRQ and DMA 3240 should be numbers, or 'auto' (for using detected 3241 settings on that particular port), or 'nofifo' 3242 (to avoid using a FIFO even if it is detected). 3243 Parallel ports are assigned in the order they 3244 are specified on the command line, starting 3245 with parport0. 3246 3247 parport_init_mode= [HW,PPT] 3248 Configure VIA parallel port to operate in 3249 a specific mode. This is necessary on Pegasos 3250 computer where firmware has no options for setting 3251 up parallel port mode and sets it to spp. 3252 Currently this function knows 686a and 8231 chips. 3253 Format: [spp|ps2|epp|ecp|ecpepp] 3254 3255 pause_on_oops= 3256 Halt all CPUs after the first oops has been printed for 3257 the specified number of seconds. This is to be used if 3258 your oopses keep scrolling off the screen. 3259 3260 pcbit= [HW,ISDN] 3261 3262 pcd. [PARIDE] 3263 See header of drivers/block/paride/pcd.c. 3264 See also Documentation/blockdev/paride.txt. 3265 3266 pci=option[,option...] [PCI] various PCI subsystem options. 3267 3268 Some options herein operate on a specific device 3269 or a set of devices (<pci_dev>). These are 3270 specified in one of the following formats: 3271 3272 [<domain>:]<bus>:<dev>.<func>[/<dev>.<func>]* 3273 pci:<vendor>:<device>[:<subvendor>:<subdevice>] 3274 3275 Note: the first format specifies a PCI 3276 bus/device/function address which may change 3277 if new hardware is inserted, if motherboard 3278 firmware changes, or due to changes caused 3279 by other kernel parameters. If the 3280 domain is left unspecified, it is 3281 taken to be zero. Optionally, a path 3282 to a device through multiple device/function 3283 addresses can be specified after the base 3284 address (this is more robust against 3285 renumbering issues). The second format 3286 selects devices using IDs from the 3287 configuration space which may match multiple 3288 devices in the system. 3289 3290 earlydump dump PCI config space before the kernel 3291 changes anything 3292 off [X86] don't probe for the PCI bus 3293 bios [X86-32] force use of PCI BIOS, don't access 3294 the hardware directly. Use this if your machine 3295 has a non-standard PCI host bridge. 3296 nobios [X86-32] disallow use of PCI BIOS, only direct 3297 hardware access methods are allowed. Use this 3298 if you experience crashes upon bootup and you 3299 suspect they are caused by the BIOS. 3300 conf1 [X86] Force use of PCI Configuration Access 3301 Mechanism 1 (config address in IO port 0xCF8, 3302 data in IO port 0xCFC, both 32-bit). 3303 conf2 [X86] Force use of PCI Configuration Access 3304 Mechanism 2 (IO port 0xCF8 is an 8-bit port for 3305 the function, IO port 0xCFA, also 8-bit, sets 3306 bus number. The config space is then accessed 3307 through ports 0xC000-0xCFFF). 3308 See http://wiki.osdev.org/PCI for more info 3309 on the configuration access mechanisms. 3310 noaer [PCIE] If the PCIEAER kernel config parameter is 3311 enabled, this kernel boot option can be used to 3312 disable the use of PCIE advanced error reporting. 3313 nodomains [PCI] Disable support for multiple PCI 3314 root domains (aka PCI segments, in ACPI-speak). 3315 nommconf [X86] Disable use of MMCONFIG for PCI 3316 Configuration 3317 check_enable_amd_mmconf [X86] check for and enable 3318 properly configured MMIO access to PCI 3319 config space on AMD family 10h CPU 3320 nomsi [MSI] If the PCI_MSI kernel config parameter is 3321 enabled, this kernel boot option can be used to 3322 disable the use of MSI interrupts system-wide. 3323 noioapicquirk [APIC] Disable all boot interrupt quirks. 3324 Safety option to keep boot IRQs enabled. This 3325 should never be necessary. 3326 ioapicreroute [APIC] Enable rerouting of boot IRQs to the 3327 primary IO-APIC for bridges that cannot disable 3328 boot IRQs. This fixes a source of spurious IRQs 3329 when the system masks IRQs. 3330 noioapicreroute [APIC] Disable workaround that uses the 3331 boot IRQ equivalent of an IRQ that connects to 3332 a chipset where boot IRQs cannot be disabled. 3333 The opposite of ioapicreroute. 3334 biosirq [X86-32] Use PCI BIOS calls to get the interrupt 3335 routing table. These calls are known to be buggy 3336 on several machines and they hang the machine 3337 when used, but on other computers it's the only 3338 way to get the interrupt routing table. Try 3339 this option if the kernel is unable to allocate 3340 IRQs or discover secondary PCI buses on your 3341 motherboard. 3342 rom [X86] Assign address space to expansion ROMs. 3343 Use with caution as certain devices share 3344 address decoders between ROMs and other 3345 resources. 3346 norom [X86] Do not assign address space to 3347 expansion ROMs that do not already have 3348 BIOS assigned address ranges. 3349 nobar [X86] Do not assign address space to the 3350 BARs that weren't assigned by the BIOS. 3351 irqmask=0xMMMM [X86] Set a bit mask of IRQs allowed to be 3352 assigned automatically to PCI devices. You can 3353 make the kernel exclude IRQs of your ISA cards 3354 this way. 3355 pirqaddr=0xAAAAA [X86] Specify the physical address 3356 of the PIRQ table (normally generated 3357 by the BIOS) if it is outside the 3358 F0000h-100000h range. 3359 lastbus=N [X86] Scan all buses thru bus #N. Can be 3360 useful if the kernel is unable to find your 3361 secondary buses and you want to tell it 3362 explicitly which ones they are. 3363 assign-busses [X86] Always assign all PCI bus 3364 numbers ourselves, overriding 3365 whatever the firmware may have done. 3366 usepirqmask [X86] Honor the possible IRQ mask stored 3367 in the BIOS $PIR table. This is needed on 3368 some systems with broken BIOSes, notably 3369 some HP Pavilion N5400 and Omnibook XE3 3370 notebooks. This will have no effect if ACPI 3371 IRQ routing is enabled. 3372 noacpi [X86] Do not use ACPI for IRQ routing 3373 or for PCI scanning. 3374 use_crs [X86] Use PCI host bridge window information 3375 from ACPI. On BIOSes from 2008 or later, this 3376 is enabled by default. If you need to use this, 3377 please report a bug. 3378 nocrs [X86] Ignore PCI host bridge windows from ACPI. 3379 If you need to use this, please report a bug. 3380 routeirq Do IRQ routing for all PCI devices. 3381 This is normally done in pci_enable_device(), 3382 so this option is a temporary workaround 3383 for broken drivers that don't call it. 3384 skip_isa_align [X86] do not align io start addr, so can 3385 handle more pci cards 3386 noearly [X86] Don't do any early type 1 scanning. 3387 This might help on some broken boards which 3388 machine check when some devices' config space 3389 is read. But various workarounds are disabled 3390 and some IOMMU drivers will not work. 3391 bfsort Sort PCI devices into breadth-first order. 3392 This sorting is done to get a device 3393 order compatible with older (<= 2.4) kernels. 3394 nobfsort Don't sort PCI devices into breadth-first order. 3395 pcie_bus_tune_off Disable PCIe MPS (Max Payload Size) 3396 tuning and use the BIOS-configured MPS defaults. 3397 pcie_bus_safe Set every device's MPS to the largest value 3398 supported by all devices below the root complex. 3399 pcie_bus_perf Set device MPS to the largest allowable MPS 3400 based on its parent bus. Also set MRRS (Max 3401 Read Request Size) to the largest supported 3402 value (no larger than the MPS that the device 3403 or bus can support) for best performance. 3404 pcie_bus_peer2peer Set every device's MPS to 128B, which 3405 every device is guaranteed to support. This 3406 configuration allows peer-to-peer DMA between 3407 any pair of devices, possibly at the cost of 3408 reduced performance. This also guarantees 3409 that hot-added devices will work. 3410 cbiosize=nn[KMG] The fixed amount of bus space which is 3411 reserved for the CardBus bridge's IO window. 3412 The default value is 256 bytes. 3413 cbmemsize=nn[KMG] The fixed amount of bus space which is 3414 reserved for the CardBus bridge's memory 3415 window. The default value is 64 megabytes. 3416 resource_alignment= 3417 Format: 3418 [<order of align>@]<pci_dev>[; ...] 3419 Specifies alignment and device to reassign 3420 aligned memory resources. How to 3421 specify the device is described above. 3422 If <order of align> is not specified, 3423 PAGE_SIZE is used as alignment. 3424 PCI-PCI bridge can be specified, if resource 3425 windows need to be expanded. 3426 To specify the alignment for several 3427 instances of a device, the PCI vendor, 3428 device, subvendor, and subdevice may be 3429 specified, e.g., 4096@pci:8086:9c22:103c:198f 3430 ecrc= Enable/disable PCIe ECRC (transaction layer 3431 end-to-end CRC checking). 3432 bios: Use BIOS/firmware settings. This is the 3433 the default. 3434 off: Turn ECRC off 3435 on: Turn ECRC on. 3436 hpiosize=nn[KMG] The fixed amount of bus space which is 3437 reserved for hotplug bridge's IO window. 3438 Default size is 256 bytes. 3439 hpmemsize=nn[KMG] The fixed amount of bus space which is 3440 reserved for hotplug bridge's memory window. 3441 Default size is 2 megabytes. 3442 hpbussize=nn The minimum amount of additional bus numbers 3443 reserved for buses below a hotplug bridge. 3444 Default is 1. 3445 realloc= Enable/disable reallocating PCI bridge resources 3446 if allocations done by BIOS are too small to 3447 accommodate resources required by all child 3448 devices. 3449 off: Turn realloc off 3450 on: Turn realloc on 3451 realloc same as realloc=on 3452 noari do not use PCIe ARI. 3453 noats [PCIE, Intel-IOMMU, AMD-IOMMU] 3454 do not use PCIe ATS (and IOMMU device IOTLB). 3455 pcie_scan_all Scan all possible PCIe devices. Otherwise we 3456 only look for one device below a PCIe downstream 3457 port. 3458 big_root_window Try to add a big 64bit memory window to the PCIe 3459 root complex on AMD CPUs. Some GFX hardware 3460 can resize a BAR to allow access to all VRAM. 3461 Adding the window is slightly risky (it may 3462 conflict with unreported devices), so this 3463 taints the kernel. 3464 disable_acs_redir=<pci_dev>[; ...] 3465 Specify one or more PCI devices (in the format 3466 specified above) separated by semicolons. 3467 Each device specified will have the PCI ACS 3468 redirect capabilities forced off which will 3469 allow P2P traffic between devices through 3470 bridges without forcing it upstream. Note: 3471 this removes isolation between devices and 3472 may put more devices in an IOMMU group. 3473 force_floating [S390] Force usage of floating interrupts. 3474 nomio [S390] Do not use MIO instructions. 3475 3476 pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power 3477 Management. 3478 off Disable ASPM. 3479 force Enable ASPM even on devices that claim not to support it. 3480 WARNING: Forcing ASPM on may cause system lockups. 3481 3482 pcie_ports= [PCIE] PCIe port services handling: 3483 native Use native PCIe services (PME, AER, DPC, PCIe hotplug) 3484 even if the platform doesn't give the OS permission to 3485 use them. This may cause conflicts if the platform 3486 also tries to use these services. 3487 compat Disable native PCIe services (PME, AER, DPC, PCIe 3488 hotplug). 3489 3490 pcie_port_pm= [PCIE] PCIe port power management handling: 3491 off Disable power management of all PCIe ports 3492 force Forcibly enable power management of all PCIe ports 3493 3494 pcie_pme= [PCIE,PM] Native PCIe PME signaling options: 3495 nomsi Do not use MSI for native PCIe PME signaling (this makes 3496 all PCIe root ports use INTx for all services). 3497 3498 pcmv= [HW,PCMCIA] BadgePAD 4 3499 3500 pd_ignore_unused 3501 [PM] 3502 Keep all power-domains already enabled by bootloader on, 3503 even if no driver has claimed them. This is useful 3504 for debug and development, but should not be 3505 needed on a platform with proper driver support. 3506 3507 pd. [PARIDE] 3508 See Documentation/blockdev/paride.txt. 3509 3510 pdcchassis= [PARISC,HW] Disable/Enable PDC Chassis Status codes at 3511 boot time. 3512 Format: { 0 | 1 } 3513 See arch/parisc/kernel/pdc_chassis.c 3514 3515 percpu_alloc= Select which percpu first chunk allocator to use. 3516 Currently supported values are "embed" and "page". 3517 Archs may support subset or none of the selections. 3518 See comments in mm/percpu.c for details on each 3519 allocator. This parameter is primarily for debugging 3520 and performance comparison. 3521 3522 pf. [PARIDE] 3523 See Documentation/blockdev/paride.txt. 3524 3525 pg. [PARIDE] 3526 See Documentation/blockdev/paride.txt. 3527 3528 pirq= [SMP,APIC] Manual mp-table setup 3529 See Documentation/x86/i386/IO-APIC.rst. 3530 3531 plip= [PPT,NET] Parallel port network link 3532 Format: { parport<nr> | timid | 0 } 3533 See also Documentation/admin-guide/parport.rst. 3534 3535 pmtmr= [X86] Manual setup of pmtmr I/O Port. 3536 Override pmtimer IOPort with a hex value. 3537 e.g. pmtmr=0x508 3538 3539 pnp.debug=1 [PNP] 3540 Enable PNP debug messages (depends on the 3541 CONFIG_PNP_DEBUG_MESSAGES option). Change at run-time 3542 via /sys/module/pnp/parameters/debug. We always show 3543 current resource usage; turning this on also shows 3544 possible settings and some assignment information. 3545 3546 pnpacpi= [ACPI] 3547 { off } 3548 3549 pnpbios= [ISAPNP] 3550 { on | off | curr | res | no-curr | no-res } 3551 3552 pnp_reserve_irq= 3553 [ISAPNP] Exclude IRQs for the autoconfiguration 3554 3555 pnp_reserve_dma= 3556 [ISAPNP] Exclude DMAs for the autoconfiguration 3557 3558 pnp_reserve_io= [ISAPNP] Exclude I/O ports for the autoconfiguration 3559 Ranges are in pairs (I/O port base and size). 3560 3561 pnp_reserve_mem= 3562 [ISAPNP] Exclude memory regions for the 3563 autoconfiguration. 3564 Ranges are in pairs (memory base and size). 3565 3566 ports= [IP_VS_FTP] IPVS ftp helper module 3567 Default is 21. 3568 Up to 8 (IP_VS_APP_MAX_PORTS) ports 3569 may be specified. 3570 Format: <port>,<port>.... 3571 3572 powersave=off [PPC] This option disables power saving features. 3573 It specifically disables cpuidle and sets the 3574 platform machine description specific power_save 3575 function to NULL. On Idle the CPU just reduces 3576 execution priority. 3577 3578 ppc_strict_facility_enable 3579 [PPC] This option catches any kernel floating point, 3580 Altivec, VSX and SPE outside of regions specifically 3581 allowed (eg kernel_enable_fpu()/kernel_disable_fpu()). 3582 There is some performance impact when enabling this. 3583 3584 ppc_tm= [PPC] 3585 Format: {"off"} 3586 Disable Hardware Transactional Memory 3587 3588 print-fatal-signals= 3589 [KNL] debug: print fatal signals 3590 3591 If enabled, warn about various signal handling 3592 related application anomalies: too many signals, 3593 too many POSIX.1 timers, fatal signals causing a 3594 coredump - etc. 3595 3596 If you hit the warning due to signal overflow, 3597 you might want to try "ulimit -i unlimited". 3598 3599 default: off. 3600 3601 printk.always_kmsg_dump= 3602 Trigger kmsg_dump for cases other than kernel oops or 3603 panics 3604 Format: <bool> (1/Y/y=enable, 0/N/n=disable) 3605 default: disabled 3606 3607 printk.devkmsg={on,off,ratelimit} 3608 Control writing to /dev/kmsg. 3609 on - unlimited logging to /dev/kmsg from userspace 3610 off - logging to /dev/kmsg disabled 3611 ratelimit - ratelimit the logging 3612 Default: ratelimit 3613 3614 printk.time= Show timing data prefixed to each printk message line 3615 Format: <bool> (1/Y/y=enable, 0/N/n=disable) 3616 3617 processor.max_cstate= [HW,ACPI] 3618 Limit processor to maximum C-state 3619 max_cstate=9 overrides any DMI blacklist limit. 3620 3621 processor.nocst [HW,ACPI] 3622 Ignore the _CST method to determine C-states, 3623 instead using the legacy FADT method 3624 3625 profile= [KNL] Enable kernel profiling via /proc/profile 3626 Format: [<profiletype>,]<number> 3627 Param: <profiletype>: "schedule", "sleep", or "kvm" 3628 [defaults to kernel profiling] 3629 Param: "schedule" - profile schedule points. 3630 Param: "sleep" - profile D-state sleeping (millisecs). 3631 Requires CONFIG_SCHEDSTATS 3632 Param: "kvm" - profile VM exits. 3633 Param: <number> - step/bucket size as a power of 2 for 3634 statistical time based profiling. 3635 3636 prompt_ramdisk= [RAM] List of RAM disks to prompt for floppy disk 3637 before loading. 3638 See Documentation/blockdev/ramdisk.txt. 3639 3640 psi= [KNL] Enable or disable pressure stall information 3641 tracking. 3642 Format: <bool> 3643 3644 psmouse.proto= [HW,MOUSE] Highest PS2 mouse protocol extension to 3645 probe for; one of (bare|imps|exps|lifebook|any). 3646 psmouse.rate= [HW,MOUSE] Set desired mouse report rate, in reports 3647 per second. 3648 psmouse.resetafter= [HW,MOUSE] 3649 Try to reset the device after so many bad packets 3650 (0 = never). 3651 psmouse.resolution= 3652 [HW,MOUSE] Set desired mouse resolution, in dpi. 3653 psmouse.smartscroll= 3654 [HW,MOUSE] Controls Logitech smartscroll autorepeat. 3655 0 = disabled, 1 = enabled (default). 3656 3657 pstore.backend= Specify the name of the pstore backend to use 3658 3659 pt. [PARIDE] 3660 See Documentation/blockdev/paride.txt. 3661 3662 pti= [X86_64] Control Page Table Isolation of user and 3663 kernel address spaces. Disabling this feature 3664 removes hardening, but improves performance of 3665 system calls and interrupts. 3666 3667 on - unconditionally enable 3668 off - unconditionally disable 3669 auto - kernel detects whether your CPU model is 3670 vulnerable to issues that PTI mitigates 3671 3672 Not specifying this option is equivalent to pti=auto. 3673 3674 nopti [X86_64] 3675 Equivalent to pti=off 3676 3677 pty.legacy_count= 3678 [KNL] Number of legacy pty's. Overwrites compiled-in 3679 default number. 3680 3681 quiet [KNL] Disable most log messages 3682 3683 r128= [HW,DRM] 3684 3685 raid= [HW,RAID] 3686 See Documentation/admin-guide/md.rst. 3687 3688 ramdisk_size= [RAM] Sizes of RAM disks in kilobytes 3689 See Documentation/blockdev/ramdisk.txt. 3690 3691 random.trust_cpu={on,off} 3692 [KNL] Enable or disable trusting the use of the 3693 CPU's random number generator (if available) to 3694 fully seed the kernel's CRNG. Default is controlled 3695 by CONFIG_RANDOM_TRUST_CPU. 3696 3697 ras=option[,option,...] [KNL] RAS-specific options 3698 3699 cec_disable [X86] 3700 Disable the Correctable Errors Collector, 3701 see CONFIG_RAS_CEC help text. 3702 3703 rcu_nocbs= [KNL] 3704 The argument is a cpu list, as described above, 3705 except that the string "all" can be used to 3706 specify every CPU on the system. 3707 3708 In kernels built with CONFIG_RCU_NOCB_CPU=y, set 3709 the specified list of CPUs to be no-callback CPUs. 3710 Invocation of these CPUs' RCU callbacks will be 3711 offloaded to "rcuox/N" kthreads created for that 3712 purpose, where "x" is "p" for RCU-preempt, and 3713 "s" for RCU-sched, and "N" is the CPU number. 3714 This reduces OS jitter on the offloaded CPUs, 3715 which can be useful for HPC and real-time 3716 workloads. It can also improve energy efficiency 3717 for asymmetric multiprocessors. 3718 3719 rcu_nocb_poll [KNL] 3720 Rather than requiring that offloaded CPUs 3721 (specified by rcu_nocbs= above) explicitly 3722 awaken the corresponding "rcuoN" kthreads, 3723 make these kthreads poll for callbacks. 3724 This improves the real-time response for the 3725 offloaded CPUs by relieving them of the need to 3726 wake up the corresponding kthread, but degrades 3727 energy efficiency by requiring that the kthreads 3728 periodically wake up to do the polling. 3729 3730 rcutree.blimit= [KNL] 3731 Set maximum number of finished RCU callbacks to 3732 process in one batch. 3733 3734 rcutree.dump_tree= [KNL] 3735 Dump the structure of the rcu_node combining tree 3736 out at early boot. This is used for diagnostic 3737 purposes, to verify correct tree setup. 3738 3739 rcutree.gp_cleanup_delay= [KNL] 3740 Set the number of jiffies to delay each step of 3741 RCU grace-period cleanup. 3742 3743 rcutree.gp_init_delay= [KNL] 3744 Set the number of jiffies to delay each step of 3745 RCU grace-period initialization. 3746 3747 rcutree.gp_preinit_delay= [KNL] 3748 Set the number of jiffies to delay each step of 3749 RCU grace-period pre-initialization, that is, 3750 the propagation of recent CPU-hotplug changes up 3751 the rcu_node combining tree. 3752 3753 rcutree.rcu_fanout_exact= [KNL] 3754 Disable autobalancing of the rcu_node combining 3755 tree. This is used by rcutorture, and might 3756 possibly be useful for architectures having high 3757 cache-to-cache transfer latencies. 3758 3759 rcutree.rcu_fanout_leaf= [KNL] 3760 Change the number of CPUs assigned to each 3761 leaf rcu_node structure. Useful for very 3762 large systems, which will choose the value 64, 3763 and for NUMA systems with large remote-access 3764 latencies, which will choose a value aligned 3765 with the appropriate hardware boundaries. 3766 3767 rcutree.jiffies_till_first_fqs= [KNL] 3768 Set delay from grace-period initialization to 3769 first attempt to force quiescent states. 3770 Units are jiffies, minimum value is zero, 3771 and maximum value is HZ. 3772 3773 rcutree.jiffies_till_next_fqs= [KNL] 3774 Set delay between subsequent attempts to force 3775 quiescent states. Units are jiffies, minimum 3776 value is one, and maximum value is HZ. 3777 3778 rcutree.jiffies_till_sched_qs= [KNL] 3779 Set required age in jiffies for a 3780 given grace period before RCU starts 3781 soliciting quiescent-state help from 3782 rcu_note_context_switch() and cond_resched(). 3783 If not specified, the kernel will calculate 3784 a value based on the most recent settings 3785 of rcutree.jiffies_till_first_fqs 3786 and rcutree.jiffies_till_next_fqs. 3787 This calculated value may be viewed in 3788 rcutree.jiffies_to_sched_qs. Any attempt to set 3789 rcutree.jiffies_to_sched_qs will be cheerfully 3790 overwritten. 3791 3792 rcutree.kthread_prio= [KNL,BOOT] 3793 Set the SCHED_FIFO priority of the RCU per-CPU 3794 kthreads (rcuc/N). This value is also used for 3795 the priority of the RCU boost threads (rcub/N) 3796 and for the RCU grace-period kthreads (rcu_bh, 3797 rcu_preempt, and rcu_sched). If RCU_BOOST is 3798 set, valid values are 1-99 and the default is 1 3799 (the least-favored priority). Otherwise, when 3800 RCU_BOOST is not set, valid values are 0-99 and 3801 the default is zero (non-realtime operation). 3802 3803 rcutree.rcu_nocb_leader_stride= [KNL] 3804 Set the number of NOCB kthread groups, which 3805 defaults to the square root of the number of 3806 CPUs. Larger numbers reduces the wakeup overhead 3807 on the per-CPU grace-period kthreads, but increases 3808 that same overhead on each group's leader. 3809 3810 rcutree.qhimark= [KNL] 3811 Set threshold of queued RCU callbacks beyond which 3812 batch limiting is disabled. 3813 3814 rcutree.qlowmark= [KNL] 3815 Set threshold of queued RCU callbacks below which 3816 batch limiting is re-enabled. 3817 3818 rcutree.rcu_idle_gp_delay= [KNL] 3819 Set wakeup interval for idle CPUs that have 3820 RCU callbacks (RCU_FAST_NO_HZ=y). 3821 3822 rcutree.rcu_idle_lazy_gp_delay= [KNL] 3823 Set wakeup interval for idle CPUs that have 3824 only "lazy" RCU callbacks (RCU_FAST_NO_HZ=y). 3825 Lazy RCU callbacks are those which RCU can 3826 prove do nothing more than free memory. 3827 3828 rcutree.rcu_kick_kthreads= [KNL] 3829 Cause the grace-period kthread to get an extra 3830 wake_up() if it sleeps three times longer than 3831 it should at force-quiescent-state time. 3832 This wake_up() will be accompanied by a 3833 WARN_ONCE() splat and an ftrace_dump(). 3834 3835 rcutree.sysrq_rcu= [KNL] 3836 Commandeer a sysrq key to dump out Tree RCU's 3837 rcu_node tree with an eye towards determining 3838 why a new grace period has not yet started. 3839 3840 rcuperf.gp_async= [KNL] 3841 Measure performance of asynchronous 3842 grace-period primitives such as call_rcu(). 3843 3844 rcuperf.gp_async_max= [KNL] 3845 Specify the maximum number of outstanding 3846 callbacks per writer thread. When a writer 3847 thread exceeds this limit, it invokes the 3848 corresponding flavor of rcu_barrier() to allow 3849 previously posted callbacks to drain. 3850 3851 rcuperf.gp_exp= [KNL] 3852 Measure performance of expedited synchronous 3853 grace-period primitives. 3854 3855 rcuperf.holdoff= [KNL] 3856 Set test-start holdoff period. The purpose of 3857 this parameter is to delay the start of the 3858 test until boot completes in order to avoid 3859 interference. 3860 3861 rcuperf.nreaders= [KNL] 3862 Set number of RCU readers. The value -1 selects 3863 N, where N is the number of CPUs. A value 3864 "n" less than -1 selects N-n+1, where N is again 3865 the number of CPUs. For example, -2 selects N 3866 (the number of CPUs), -3 selects N+1, and so on. 3867 A value of "n" less than or equal to -N selects 3868 a single reader. 3869 3870 rcuperf.nwriters= [KNL] 3871 Set number of RCU writers. The values operate 3872 the same as for rcuperf.nreaders. 3873 N, where N is the number of CPUs 3874 3875 rcuperf.perf_type= [KNL] 3876 Specify the RCU implementation to test. 3877 3878 rcuperf.shutdown= [KNL] 3879 Shut the system down after performance tests 3880 complete. This is useful for hands-off automated 3881 testing. 3882 3883 rcuperf.verbose= [KNL] 3884 Enable additional printk() statements. 3885 3886 rcuperf.writer_holdoff= [KNL] 3887 Write-side holdoff between grace periods, 3888 in microseconds. The default of zero says 3889 no holdoff. 3890 3891 rcutorture.fqs_duration= [KNL] 3892 Set duration of force_quiescent_state bursts 3893 in microseconds. 3894 3895 rcutorture.fqs_holdoff= [KNL] 3896 Set holdoff time within force_quiescent_state bursts 3897 in microseconds. 3898 3899 rcutorture.fqs_stutter= [KNL] 3900 Set wait time between force_quiescent_state bursts 3901 in seconds. 3902 3903 rcutorture.fwd_progress= [KNL] 3904 Enable RCU grace-period forward-progress testing 3905 for the types of RCU supporting this notion. 3906 3907 rcutorture.fwd_progress_div= [KNL] 3908 Specify the fraction of a CPU-stall-warning 3909 period to do tight-loop forward-progress testing. 3910 3911 rcutorture.fwd_progress_holdoff= [KNL] 3912 Number of seconds to wait between successive 3913 forward-progress tests. 3914 3915 rcutorture.fwd_progress_need_resched= [KNL] 3916 Enclose cond_resched() calls within checks for 3917 need_resched() during tight-loop forward-progress 3918 testing. 3919 3920 rcutorture.gp_cond= [KNL] 3921 Use conditional/asynchronous update-side 3922 primitives, if available. 3923 3924 rcutorture.gp_exp= [KNL] 3925 Use expedited update-side primitives, if available. 3926 3927 rcutorture.gp_normal= [KNL] 3928 Use normal (non-expedited) asynchronous 3929 update-side primitives, if available. 3930 3931 rcutorture.gp_sync= [KNL] 3932 Use normal (non-expedited) synchronous 3933 update-side primitives, if available. If all 3934 of rcutorture.gp_cond=, rcutorture.gp_exp=, 3935 rcutorture.gp_normal=, and rcutorture.gp_sync= 3936 are zero, rcutorture acts as if is interpreted 3937 they are all non-zero. 3938 3939 rcutorture.n_barrier_cbs= [KNL] 3940 Set callbacks/threads for rcu_barrier() testing. 3941 3942 rcutorture.nfakewriters= [KNL] 3943 Set number of concurrent RCU writers. These just 3944 stress RCU, they don't participate in the actual 3945 test, hence the "fake". 3946 3947 rcutorture.nreaders= [KNL] 3948 Set number of RCU readers. The value -1 selects 3949 N-1, where N is the number of CPUs. A value 3950 "n" less than -1 selects N-n-2, where N is again 3951 the number of CPUs. For example, -2 selects N 3952 (the number of CPUs), -3 selects N+1, and so on. 3953 3954 rcutorture.object_debug= [KNL] 3955 Enable debug-object double-call_rcu() testing. 3956 3957 rcutorture.onoff_holdoff= [KNL] 3958 Set time (s) after boot for CPU-hotplug testing. 3959 3960 rcutorture.onoff_interval= [KNL] 3961 Set time (jiffies) between CPU-hotplug operations, 3962 or zero to disable CPU-hotplug testing. 3963 3964 rcutorture.shuffle_interval= [KNL] 3965 Set task-shuffle interval (s). Shuffling tasks 3966 allows some CPUs to go into dyntick-idle mode 3967 during the rcutorture test. 3968 3969 rcutorture.shutdown_secs= [KNL] 3970 Set time (s) after boot system shutdown. This 3971 is useful for hands-off automated testing. 3972 3973 rcutorture.stall_cpu= [KNL] 3974 Duration of CPU stall (s) to test RCU CPU stall 3975 warnings, zero to disable. 3976 3977 rcutorture.stall_cpu_holdoff= [KNL] 3978 Time to wait (s) after boot before inducing stall. 3979 3980 rcutorture.stall_cpu_irqsoff= [KNL] 3981 Disable interrupts while stalling if set. 3982 3983 rcutorture.stat_interval= [KNL] 3984 Time (s) between statistics printk()s. 3985 3986 rcutorture.stutter= [KNL] 3987 Time (s) to stutter testing, for example, specifying 3988 five seconds causes the test to run for five seconds, 3989 wait for five seconds, and so on. This tests RCU's 3990 ability to transition abruptly to and from idle. 3991 3992 rcutorture.test_boost= [KNL] 3993 Test RCU priority boosting? 0=no, 1=maybe, 2=yes. 3994 "Maybe" means test if the RCU implementation 3995 under test support RCU priority boosting. 3996 3997 rcutorture.test_boost_duration= [KNL] 3998 Duration (s) of each individual boost test. 3999 4000 rcutorture.test_boost_interval= [KNL] 4001 Interval (s) between each boost test. 4002 4003 rcutorture.test_no_idle_hz= [KNL] 4004 Test RCU's dyntick-idle handling. See also the 4005 rcutorture.shuffle_interval parameter. 4006 4007 rcutorture.torture_type= [KNL] 4008 Specify the RCU implementation to test. 4009 4010 rcutorture.verbose= [KNL] 4011 Enable additional printk() statements. 4012 4013 rcupdate.rcu_cpu_stall_suppress= [KNL] 4014 Suppress RCU CPU stall warning messages. 4015 4016 rcupdate.rcu_cpu_stall_timeout= [KNL] 4017 Set timeout for RCU CPU stall warning messages. 4018 4019 rcupdate.rcu_expedited= [KNL] 4020 Use expedited grace-period primitives, for 4021 example, synchronize_rcu_expedited() instead 4022 of synchronize_rcu(). This reduces latency, 4023 but can increase CPU utilization, degrade 4024 real-time latency, and degrade energy efficiency. 4025 No effect on CONFIG_TINY_RCU kernels. 4026 4027 rcupdate.rcu_normal= [KNL] 4028 Use only normal grace-period primitives, 4029 for example, synchronize_rcu() instead of 4030 synchronize_rcu_expedited(). This improves 4031 real-time latency, CPU utilization, and 4032 energy efficiency, but can expose users to 4033 increased grace-period latency. This parameter 4034 overrides rcupdate.rcu_expedited. No effect on 4035 CONFIG_TINY_RCU kernels. 4036 4037 rcupdate.rcu_normal_after_boot= [KNL] 4038 Once boot has completed (that is, after 4039 rcu_end_inkernel_boot() has been invoked), use 4040 only normal grace-period primitives. No effect 4041 on CONFIG_TINY_RCU kernels. 4042 4043 rcupdate.rcu_task_stall_timeout= [KNL] 4044 Set timeout in jiffies for RCU task stall warning 4045 messages. Disable with a value less than or equal 4046 to zero. 4047 4048 rcupdate.rcu_self_test= [KNL] 4049 Run the RCU early boot self tests 4050 4051 rdinit= [KNL] 4052 Format: <full_path> 4053 Run specified binary instead of /init from the ramdisk, 4054 used for early userspace startup. See initrd. 4055 4056 rdt= [HW,X86,RDT] 4057 Turn on/off individual RDT features. List is: 4058 cmt, mbmtotal, mbmlocal, l3cat, l3cdp, l2cat, l2cdp, 4059 mba. 4060 E.g. to turn on cmt and turn off mba use: 4061 rdt=cmt,!mba 4062 4063 reboot= [KNL] 4064 Format (x86 or x86_64): 4065 [w[arm] | c[old] | h[ard] | s[oft] | g[pio]] \ 4066 [[,]s[mp]#### \ 4067 [[,]b[ios] | a[cpi] | k[bd] | t[riple] | e[fi] | p[ci]] \ 4068 [[,]f[orce] 4069 Where reboot_mode is one of warm (soft) or cold (hard) or gpio 4070 (prefix with 'panic_' to set mode for panic 4071 reboot only), 4072 reboot_type is one of bios, acpi, kbd, triple, efi, or pci, 4073 reboot_force is either force or not specified, 4074 reboot_cpu is s[mp]#### with #### being the processor 4075 to be used for rebooting. 4076 4077 relax_domain_level= 4078 [KNL, SMP] Set scheduler's default relax_domain_level. 4079 See Documentation/cgroup-v1/cpusets.txt. 4080 4081 reserve= [KNL,BUGS] Force kernel to ignore I/O ports or memory 4082 Format: <base1>,<size1>[,<base2>,<size2>,...] 4083 Reserve I/O ports or memory so the kernel won't use 4084 them. If <base> is less than 0x10000, the region 4085 is assumed to be I/O ports; otherwise it is memory. 4086 4087 reservetop= [X86-32] 4088 Format: nn[KMG] 4089 Reserves a hole at the top of the kernel virtual 4090 address space. 4091 4092 reservelow= [X86] 4093 Format: nn[K] 4094 Set the amount of memory to reserve for BIOS at 4095 the bottom of the address space. 4096 4097 reset_devices [KNL] Force drivers to reset the underlying device 4098 during initialization. 4099 4100 resume= [SWSUSP] 4101 Specify the partition device for software suspend 4102 Format: 4103 {/dev/<dev> | PARTUUID=<uuid> | <int>:<int> | <hex>} 4104 4105 resume_offset= [SWSUSP] 4106 Specify the offset from the beginning of the partition 4107 given by "resume=" at which the swap header is located, 4108 in <PAGE_SIZE> units (needed only for swap files). 4109 See Documentation/power/swsusp-and-swap-files.txt 4110 4111 resumedelay= [HIBERNATION] Delay (in seconds) to pause before attempting to 4112 read the resume files 4113 4114 resumewait [HIBERNATION] Wait (indefinitely) for resume device to show up. 4115 Useful for devices that are detected asynchronously 4116 (e.g. USB and MMC devices). 4117 4118 hibernate= [HIBERNATION] 4119 noresume Don't check if there's a hibernation image 4120 present during boot. 4121 nocompress Don't compress/decompress hibernation images. 4122 no Disable hibernation and resume. 4123 protect_image Turn on image protection during restoration 4124 (that will set all pages holding image data 4125 during restoration read-only). 4126 4127 retain_initrd [RAM] Keep initrd memory after extraction 4128 4129 rfkill.default_state= 4130 0 "airplane mode". All wifi, bluetooth, wimax, gps, fm, 4131 etc. communication is blocked by default. 4132 1 Unblocked. 4133 4134 rfkill.master_switch_mode= 4135 0 The "airplane mode" button does nothing. 4136 1 The "airplane mode" button toggles between everything 4137 blocked and the previous configuration. 4138 2 The "airplane mode" button toggles between everything 4139 blocked and everything unblocked. 4140 4141 rhash_entries= [KNL,NET] 4142 Set number of hash buckets for route cache 4143 4144 ring3mwait=disable 4145 [KNL] Disable ring 3 MONITOR/MWAIT feature on supported 4146 CPUs. 4147 4148 ro [KNL] Mount root device read-only on boot 4149 4150 rodata= [KNL] 4151 on Mark read-only kernel memory as read-only (default). 4152 off Leave read-only kernel memory writable for debugging. 4153 4154 rockchip.usb_uart 4155 Enable the uart passthrough on the designated usb port 4156 on Rockchip SoCs. When active, the signals of the 4157 debug-uart get routed to the D+ and D- pins of the usb 4158 port and the regular usb controller gets disabled. 4159 4160 root= [KNL] Root filesystem 4161 See name_to_dev_t comment in init/do_mounts.c. 4162 4163 rootdelay= [KNL] Delay (in seconds) to pause before attempting to 4164 mount the root filesystem 4165 4166 rootflags= [KNL] Set root filesystem mount option string 4167 4168 rootfstype= [KNL] Set root filesystem type 4169 4170 rootwait [KNL] Wait (indefinitely) for root device to show up. 4171 Useful for devices that are detected asynchronously 4172 (e.g. USB and MMC devices). 4173 4174 rproc_mem=nn[KMG][@address] 4175 [KNL,ARM,CMA] Remoteproc physical memory block. 4176 Memory area to be used by remote processor image, 4177 managed by CMA. 4178 4179 rw [KNL] Mount root device read-write on boot 4180 4181 S [KNL] Run init in single mode 4182 4183 s390_iommu= [HW,S390] 4184 Set s390 IOTLB flushing mode 4185 strict 4186 With strict flushing every unmap operation will result in 4187 an IOTLB flush. Default is lazy flushing before reuse, 4188 which is faster. 4189 4190 sa1100ir [NET] 4191 See drivers/net/irda/sa1100_ir.c. 4192 4193 sbni= [NET] Granch SBNI12 leased line adapter 4194 4195 sched_debug [KNL] Enables verbose scheduler debug messages. 4196 4197 schedstats= [KNL,X86] Enable or disable scheduled statistics. 4198 Allowed values are enable and disable. This feature 4199 incurs a small amount of overhead in the scheduler 4200 but is useful for debugging and performance tuning. 4201 4202 skew_tick= [KNL] Offset the periodic timer tick per cpu to mitigate 4203 xtime_lock contention on larger systems, and/or RCU lock 4204 contention on all systems with CONFIG_MAXSMP set. 4205 Format: { "0" | "1" } 4206 0 -- disable. (may be 1 via CONFIG_CMDLINE="skew_tick=1" 4207 1 -- enable. 4208 Note: increases power consumption, thus should only be 4209 enabled if running jitter sensitive (HPC/RT) workloads. 4210 4211 security= [SECURITY] Choose a legacy "major" security module to 4212 enable at boot. This has been deprecated by the 4213 "lsm=" parameter. 4214 4215 selinux= [SELINUX] Disable or enable SELinux at boot time. 4216 Format: { "0" | "1" } 4217 See security/selinux/Kconfig help text. 4218 0 -- disable. 4219 1 -- enable. 4220 Default value is set via kernel config option. 4221 If enabled at boot time, /selinux/disable can be used 4222 later to disable prior to initial policy load. 4223 4224 apparmor= [APPARMOR] Disable or enable AppArmor at boot time 4225 Format: { "0" | "1" } 4226 See security/apparmor/Kconfig help text 4227 0 -- disable. 4228 1 -- enable. 4229 Default value is set via kernel config option. 4230 4231 serialnumber [BUGS=X86-32] 4232 4233 shapers= [NET] 4234 Maximal number of shapers. 4235 4236 simeth= [IA-64] 4237 simscsi= 4238 4239 slram= [HW,MTD] 4240 4241 slab_nomerge [MM] 4242 Disable merging of slabs with similar size. May be 4243 necessary if there is some reason to distinguish 4244 allocs to different slabs, especially in hardened 4245 environments where the risk of heap overflows and 4246 layout control by attackers can usually be 4247 frustrated by disabling merging. This will reduce 4248 most of the exposure of a heap attack to a single 4249 cache (risks via metadata attacks are mostly 4250 unchanged). Debug options disable merging on their 4251 own. 4252 For more information see Documentation/vm/slub.rst. 4253 4254 slab_max_order= [MM, SLAB] 4255 Determines the maximum allowed order for slabs. 4256 A high setting may cause OOMs due to memory 4257 fragmentation. Defaults to 1 for systems with 4258 more than 32MB of RAM, 0 otherwise. 4259 4260 slub_debug[=options[,slabs]] [MM, SLUB] 4261 Enabling slub_debug allows one to determine the 4262 culprit if slab objects become corrupted. Enabling 4263 slub_debug can create guard zones around objects and 4264 may poison objects when not in use. Also tracks the 4265 last alloc / free. For more information see 4266 Documentation/vm/slub.rst. 4267 4268 slub_memcg_sysfs= [MM, SLUB] 4269 Determines whether to enable sysfs directories for 4270 memory cgroup sub-caches. 1 to enable, 0 to disable. 4271 The default is determined by CONFIG_SLUB_MEMCG_SYSFS_ON. 4272 Enabling this can lead to a very high number of debug 4273 directories and files being created under 4274 /sys/kernel/slub. 4275 4276 slub_max_order= [MM, SLUB] 4277 Determines the maximum allowed order for slabs. 4278 A high setting may cause OOMs due to memory 4279 fragmentation. For more information see 4280 Documentation/vm/slub.rst. 4281 4282 slub_min_objects= [MM, SLUB] 4283 The minimum number of objects per slab. SLUB will 4284 increase the slab order up to slub_max_order to 4285 generate a sufficiently large slab able to contain 4286 the number of objects indicated. The higher the number 4287 of objects the smaller the overhead of tracking slabs 4288 and the less frequently locks need to be acquired. 4289 For more information see Documentation/vm/slub.rst. 4290 4291 slub_min_order= [MM, SLUB] 4292 Determines the minimum page order for slabs. Must be 4293 lower than slub_max_order. 4294 For more information see Documentation/vm/slub.rst. 4295 4296 slub_nomerge [MM, SLUB] 4297 Same with slab_nomerge. This is supported for legacy. 4298 See slab_nomerge for more information. 4299 4300 smart2= [HW] 4301 Format: <io1>[,<io2>[,...,<io8>]] 4302 4303 smsc-ircc2.nopnp [HW] Don't use PNP to discover SMC devices 4304 smsc-ircc2.ircc_cfg= [HW] Device configuration I/O port 4305 smsc-ircc2.ircc_sir= [HW] SIR base I/O port 4306 smsc-ircc2.ircc_fir= [HW] FIR base I/O port 4307 smsc-ircc2.ircc_irq= [HW] IRQ line 4308 smsc-ircc2.ircc_dma= [HW] DMA channel 4309 smsc-ircc2.ircc_transceiver= [HW] Transceiver type: 4310 0: Toshiba Satellite 1800 (GP data pin select) 4311 1: Fast pin select (default) 4312 2: ATC IRMode 4313 4314 smt [KNL,S390] Set the maximum number of threads (logical 4315 CPUs) to use per physical CPU on systems capable of 4316 symmetric multithreading (SMT). Will be capped to the 4317 actual hardware limit. 4318 Format: <integer> 4319 Default: -1 (no limit) 4320 4321 softlockup_panic= 4322 [KNL] Should the soft-lockup detector generate panics. 4323 Format: <integer> 4324 4325 A nonzero value instructs the soft-lockup detector 4326 to panic the machine when a soft-lockup occurs. This 4327 is also controlled by CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC 4328 which is the respective build-time switch to that 4329 functionality. 4330 4331 softlockup_all_cpu_backtrace= 4332 [KNL] Should the soft-lockup detector generate 4333 backtraces on all cpus. 4334 Format: <integer> 4335 4336 sonypi.*= [HW] Sony Programmable I/O Control Device driver 4337 See Documentation/laptops/sonypi.txt 4338 4339 spectre_v2= [X86] Control mitigation of Spectre variant 2 4340 (indirect branch speculation) vulnerability. 4341 The default operation protects the kernel from 4342 user space attacks. 4343 4344 on - unconditionally enable, implies 4345 spectre_v2_user=on 4346 off - unconditionally disable, implies 4347 spectre_v2_user=off 4348 auto - kernel detects whether your CPU model is 4349 vulnerable 4350 4351 Selecting 'on' will, and 'auto' may, choose a 4352 mitigation method at run time according to the 4353 CPU, the available microcode, the setting of the 4354 CONFIG_RETPOLINE configuration option, and the 4355 compiler with which the kernel was built. 4356 4357 Selecting 'on' will also enable the mitigation 4358 against user space to user space task attacks. 4359 4360 Selecting 'off' will disable both the kernel and 4361 the user space protections. 4362 4363 Specific mitigations can also be selected manually: 4364 4365 retpoline - replace indirect branches 4366 retpoline,generic - google's original retpoline 4367 retpoline,amd - AMD-specific minimal thunk 4368 4369 Not specifying this option is equivalent to 4370 spectre_v2=auto. 4371 4372 spectre_v2_user= 4373 [X86] Control mitigation of Spectre variant 2 4374 (indirect branch speculation) vulnerability between 4375 user space tasks 4376 4377 on - Unconditionally enable mitigations. Is 4378 enforced by spectre_v2=on 4379 4380 off - Unconditionally disable mitigations. Is 4381 enforced by spectre_v2=off 4382 4383 prctl - Indirect branch speculation is enabled, 4384 but mitigation can be enabled via prctl 4385 per thread. The mitigation control state 4386 is inherited on fork. 4387 4388 prctl,ibpb 4389 - Like "prctl" above, but only STIBP is 4390 controlled per thread. IBPB is issued 4391 always when switching between different user 4392 space processes. 4393 4394 seccomp 4395 - Same as "prctl" above, but all seccomp 4396 threads will enable the mitigation unless 4397 they explicitly opt out. 4398 4399 seccomp,ibpb 4400 - Like "seccomp" above, but only STIBP is 4401 controlled per thread. IBPB is issued 4402 always when switching between different 4403 user space processes. 4404 4405 auto - Kernel selects the mitigation depending on 4406 the available CPU features and vulnerability. 4407 4408 Default mitigation: 4409 If CONFIG_SECCOMP=y then "seccomp", otherwise "prctl" 4410 4411 Not specifying this option is equivalent to 4412 spectre_v2_user=auto. 4413 4414 spec_store_bypass_disable= 4415 [HW] Control Speculative Store Bypass (SSB) Disable mitigation 4416 (Speculative Store Bypass vulnerability) 4417 4418 Certain CPUs are vulnerable to an exploit against a 4419 a common industry wide performance optimization known 4420 as "Speculative Store Bypass" in which recent stores 4421 to the same memory location may not be observed by 4422 later loads during speculative execution. The idea 4423 is that such stores are unlikely and that they can 4424 be detected prior to instruction retirement at the 4425 end of a particular speculation execution window. 4426 4427 In vulnerable processors, the speculatively forwarded 4428 store can be used in a cache side channel attack, for 4429 example to read memory to which the attacker does not 4430 directly have access (e.g. inside sandboxed code). 4431 4432 This parameter controls whether the Speculative Store 4433 Bypass optimization is used. 4434 4435 On x86 the options are: 4436 4437 on - Unconditionally disable Speculative Store Bypass 4438 off - Unconditionally enable Speculative Store Bypass 4439 auto - Kernel detects whether the CPU model contains an 4440 implementation of Speculative Store Bypass and 4441 picks the most appropriate mitigation. If the 4442 CPU is not vulnerable, "off" is selected. If the 4443 CPU is vulnerable the default mitigation is 4444 architecture and Kconfig dependent. See below. 4445 prctl - Control Speculative Store Bypass per thread 4446 via prctl. Speculative Store Bypass is enabled 4447 for a process by default. The state of the control 4448 is inherited on fork. 4449 seccomp - Same as "prctl" above, but all seccomp threads 4450 will disable SSB unless they explicitly opt out. 4451 4452 Default mitigations: 4453 X86: If CONFIG_SECCOMP=y "seccomp", otherwise "prctl" 4454 4455 On powerpc the options are: 4456 4457 on,auto - On Power8 and Power9 insert a store-forwarding 4458 barrier on kernel entry and exit. On Power7 4459 perform a software flush on kernel entry and 4460 exit. 4461 off - No action. 4462 4463 Not specifying this option is equivalent to 4464 spec_store_bypass_disable=auto. 4465 4466 spia_io_base= [HW,MTD] 4467 spia_fio_base= 4468 spia_pedr= 4469 spia_peddr= 4470 4471 srcutree.counter_wrap_check [KNL] 4472 Specifies how frequently to check for 4473 grace-period sequence counter wrap for the 4474 srcu_data structure's ->srcu_gp_seq_needed field. 4475 The greater the number of bits set in this kernel 4476 parameter, the less frequently counter wrap will 4477 be checked for. Note that the bottom two bits 4478 are ignored. 4479 4480 srcutree.exp_holdoff [KNL] 4481 Specifies how many nanoseconds must elapse 4482 since the end of the last SRCU grace period for 4483 a given srcu_struct until the next normal SRCU 4484 grace period will be considered for automatic 4485 expediting. Set to zero to disable automatic 4486 expediting. 4487 4488 ssbd= [ARM64,HW] 4489 Speculative Store Bypass Disable control 4490 4491 On CPUs that are vulnerable to the Speculative 4492 Store Bypass vulnerability and offer a 4493 firmware based mitigation, this parameter 4494 indicates how the mitigation should be used: 4495 4496 force-on: Unconditionally enable mitigation for 4497 for both kernel and userspace 4498 force-off: Unconditionally disable mitigation for 4499 for both kernel and userspace 4500 kernel: Always enable mitigation in the 4501 kernel, and offer a prctl interface 4502 to allow userspace to register its 4503 interest in being mitigated too. 4504 4505 stack_guard_gap= [MM] 4506 override the default stack gap protection. The value 4507 is in page units and it defines how many pages prior 4508 to (for stacks growing down) resp. after (for stacks 4509 growing up) the main stack are reserved for no other 4510 mapping. Default value is 256 pages. 4511 4512 stacktrace [FTRACE] 4513 Enabled the stack tracer on boot up. 4514 4515 stacktrace_filter=[function-list] 4516 [FTRACE] Limit the functions that the stack tracer 4517 will trace at boot up. function-list is a comma separated 4518 list of functions. This list can be changed at run 4519 time by the stack_trace_filter file in the debugfs 4520 tracing directory. Note, this enables stack tracing 4521 and the stacktrace above is not needed. 4522 4523 sti= [PARISC,HW] 4524 Format: <num> 4525 Set the STI (builtin display/keyboard on the HP-PARISC 4526 machines) console (graphic card) which should be used 4527 as the initial boot-console. 4528 See also comment in drivers/video/console/sticore.c. 4529 4530 sti_font= [HW] 4531 See comment in drivers/video/console/sticore.c. 4532 4533 stifb= [HW] 4534 Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]] 4535 4536 sunrpc.min_resvport= 4537 sunrpc.max_resvport= 4538 [NFS,SUNRPC] 4539 SunRPC servers often require that client requests 4540 originate from a privileged port (i.e. a port in the 4541 range 0 < portnr < 1024). 4542 An administrator who wishes to reserve some of these 4543 ports for other uses may adjust the range that the 4544 kernel's sunrpc client considers to be privileged 4545 using these two parameters to set the minimum and 4546 maximum port values. 4547 4548 sunrpc.svc_rpc_per_connection_limit= 4549 [NFS,SUNRPC] 4550 Limit the number of requests that the server will 4551 process in parallel from a single connection. 4552 The default value is 0 (no limit). 4553 4554 sunrpc.pool_mode= 4555 [NFS] 4556 Control how the NFS server code allocates CPUs to 4557 service thread pools. Depending on how many NICs 4558 you have and where their interrupts are bound, this 4559 option will affect which CPUs will do NFS serving. 4560 Note: this parameter cannot be changed while the 4561 NFS server is running. 4562 4563 auto the server chooses an appropriate mode 4564 automatically using heuristics 4565 global a single global pool contains all CPUs 4566 percpu one pool for each CPU 4567 pernode one pool for each NUMA node (equivalent 4568 to global on non-NUMA machines) 4569 4570 sunrpc.tcp_slot_table_entries= 4571 sunrpc.udp_slot_table_entries= 4572 [NFS,SUNRPC] 4573 Sets the upper limit on the number of simultaneous 4574 RPC calls that can be sent from the client to a 4575 server. Increasing these values may allow you to 4576 improve throughput, but will also increase the 4577 amount of memory reserved for use by the client. 4578 4579 suspend.pm_test_delay= 4580 [SUSPEND] 4581 Sets the number of seconds to remain in a suspend test 4582 mode before resuming the system (see 4583 /sys/power/pm_test). Only available when CONFIG_PM_DEBUG 4584 is set. Default value is 5. 4585 4586 swapaccount=[0|1] 4587 [KNL] Enable accounting of swap in memory resource 4588 controller if no parameter or 1 is given or disable 4589 it if 0 is given (See Documentation/cgroup-v1/memory.txt) 4590 4591 swiotlb= [ARM,IA-64,PPC,MIPS,X86] 4592 Format: { <int> | force | noforce } 4593 <int> -- Number of I/O TLB slabs 4594 force -- force using of bounce buffers even if they 4595 wouldn't be automatically used by the kernel 4596 noforce -- Never use bounce buffers (for debugging) 4597 4598 switches= [HW,M68k] 4599 4600 sysfs.deprecated=0|1 [KNL] 4601 Enable/disable old style sysfs layout for old udev 4602 on older distributions. When this option is enabled 4603 very new udev will not work anymore. When this option 4604 is disabled (or CONFIG_SYSFS_DEPRECATED not compiled) 4605 in older udev will not work anymore. 4606 Default depends on CONFIG_SYSFS_DEPRECATED_V2 set in 4607 the kernel configuration. 4608 4609 sysrq_always_enabled 4610 [KNL] 4611 Ignore sysrq setting - this boot parameter will 4612 neutralize any effect of /proc/sys/kernel/sysrq. 4613 Useful for debugging. 4614 4615 tcpmhash_entries= [KNL,NET] 4616 Set the number of tcp_metrics_hash slots. 4617 Default value is 8192 or 16384 depending on total 4618 ram pages. This is used to specify the TCP metrics 4619 cache size. See Documentation/networking/ip-sysctl.txt 4620 "tcp_no_metrics_save" section for more details. 4621 4622 tdfx= [HW,DRM] 4623 4624 test_suspend= [SUSPEND][,N] 4625 Specify "mem" (for Suspend-to-RAM) or "standby" (for 4626 standby suspend) or "freeze" (for suspend type freeze) 4627 as the system sleep state during system startup with 4628 the optional capability to repeat N number of times. 4629 The system is woken from this state using a 4630 wakeup-capable RTC alarm. 4631 4632 thash_entries= [KNL,NET] 4633 Set number of hash buckets for TCP connection 4634 4635 thermal.act= [HW,ACPI] 4636 -1: disable all active trip points in all thermal zones 4637 <degrees C>: override all lowest active trip points 4638 4639 thermal.crt= [HW,ACPI] 4640 -1: disable all critical trip points in all thermal zones 4641 <degrees C>: override all critical trip points 4642 4643 thermal.nocrt= [HW,ACPI] 4644 Set to disable actions on ACPI thermal zone 4645 critical and hot trip points. 4646 4647 thermal.off= [HW,ACPI] 4648 1: disable ACPI thermal control 4649 4650 thermal.psv= [HW,ACPI] 4651 -1: disable all passive trip points 4652 <degrees C>: override all passive trip points to this 4653 value 4654 4655 thermal.tzp= [HW,ACPI] 4656 Specify global default ACPI thermal zone polling rate 4657 <deci-seconds>: poll all this frequency 4658 0: no polling (default) 4659 4660 threadirqs [KNL] 4661 Force threading of all interrupt handlers except those 4662 marked explicitly IRQF_NO_THREAD. 4663 4664 tmem [KNL,XEN] 4665 Enable the Transcendent memory driver if built-in. 4666 4667 tmem.cleancache=0|1 [KNL, XEN] 4668 Default is on (1). Disable the usage of the cleancache 4669 API to send anonymous pages to the hypervisor. 4670 4671 tmem.frontswap=0|1 [KNL, XEN] 4672 Default is on (1). Disable the usage of the frontswap 4673 API to send swap pages to the hypervisor. If disabled 4674 the selfballooning and selfshrinking are force disabled. 4675 4676 tmem.selfballooning=0|1 [KNL, XEN] 4677 Default is on (1). Disable the driving of swap pages 4678 to the hypervisor. 4679 4680 tmem.selfshrinking=0|1 [KNL, XEN] 4681 Default is on (1). Partial swapoff that immediately 4682 transfers pages from Xen hypervisor back to the 4683 kernel based on different criteria. 4684 4685 topology= [S390] 4686 Format: {off | on} 4687 Specify if the kernel should make use of the cpu 4688 topology information if the hardware supports this. 4689 The scheduler will make use of this information and 4690 e.g. base its process migration decisions on it. 4691 Default is on. 4692 4693 topology_updates= [KNL, PPC, NUMA] 4694 Format: {off} 4695 Specify if the kernel should ignore (off) 4696 topology updates sent by the hypervisor to this 4697 LPAR. 4698 4699 tp720= [HW,PS2] 4700 4701 tpm_suspend_pcr=[HW,TPM] 4702 Format: integer pcr id 4703 Specify that at suspend time, the tpm driver 4704 should extend the specified pcr with zeros, 4705 as a workaround for some chips which fail to 4706 flush the last written pcr on TPM_SaveState. 4707 This will guarantee that all the other pcrs 4708 are saved. 4709 4710 trace_buf_size=nn[KMG] 4711 [FTRACE] will set tracing buffer size on each cpu. 4712 4713 trace_event=[event-list] 4714 [FTRACE] Set and start specified trace events in order 4715 to facilitate early boot debugging. The event-list is a 4716 comma separated list of trace events to enable. See 4717 also Documentation/trace/events.rst 4718 4719 trace_options=[option-list] 4720 [FTRACE] Enable or disable tracer options at boot. 4721 The option-list is a comma delimited list of options 4722 that can be enabled or disabled just as if you were 4723 to echo the option name into 4724 4725 /sys/kernel/debug/tracing/trace_options 4726 4727 For example, to enable stacktrace option (to dump the 4728 stack trace of each event), add to the command line: 4729 4730 trace_options=stacktrace 4731 4732 See also Documentation/trace/ftrace.rst "trace options" 4733 section. 4734 4735 tp_printk[FTRACE] 4736 Have the tracepoints sent to printk as well as the 4737 tracing ring buffer. This is useful for early boot up 4738 where the system hangs or reboots and does not give the 4739 option for reading the tracing buffer or performing a 4740 ftrace_dump_on_oops. 4741 4742 To turn off having tracepoints sent to printk, 4743 echo 0 > /proc/sys/kernel/tracepoint_printk 4744 Note, echoing 1 into this file without the 4745 tracepoint_printk kernel cmdline option has no effect. 4746 4747 ** CAUTION ** 4748 4749 Having tracepoints sent to printk() and activating high 4750 frequency tracepoints such as irq or sched, can cause 4751 the system to live lock. 4752 4753 traceoff_on_warning 4754 [FTRACE] enable this option to disable tracing when a 4755 warning is hit. This turns off "tracing_on". Tracing can 4756 be enabled again by echoing '1' into the "tracing_on" 4757 file located in /sys/kernel/debug/tracing/ 4758 4759 This option is useful, as it disables the trace before 4760 the WARNING dump is called, which prevents the trace to 4761 be filled with content caused by the warning output. 4762 4763 This option can also be set at run time via the sysctl 4764 option: kernel/traceoff_on_warning 4765 4766 transparent_hugepage= 4767 [KNL] 4768 Format: [always|madvise|never] 4769 Can be used to control the default behavior of the system 4770 with respect to transparent hugepages. 4771 See Documentation/admin-guide/mm/transhuge.rst 4772 for more details. 4773 4774 tsc= Disable clocksource stability checks for TSC. 4775 Format: <string> 4776 [x86] reliable: mark tsc clocksource as reliable, this 4777 disables clocksource verification at runtime, as well 4778 as the stability checks done at bootup. Used to enable 4779 high-resolution timer mode on older hardware, and in 4780 virtualized environment. 4781 [x86] noirqtime: Do not use TSC to do irq accounting. 4782 Used to run time disable IRQ_TIME_ACCOUNTING on any 4783 platforms where RDTSC is slow and this accounting 4784 can add overhead. 4785 [x86] unstable: mark the TSC clocksource as unstable, this 4786 marks the TSC unconditionally unstable at bootup and 4787 avoids any further wobbles once the TSC watchdog notices. 4788 [x86] nowatchdog: disable clocksource watchdog. Used 4789 in situations with strict latency requirements (where 4790 interruptions from clocksource watchdog are not 4791 acceptable). 4792 4793 turbografx.map[2|3]= [HW,JOY] 4794 TurboGraFX parallel port interface 4795 Format: 4796 <port#>,<js1>,<js2>,<js3>,<js4>,<js5>,<js6>,<js7> 4797 See also Documentation/input/devices/joystick-parport.rst 4798 4799 udbg-immortal [PPC] When debugging early kernel crashes that 4800 happen after console_init() and before a proper 4801 console driver takes over, this boot options might 4802 help "seeing" what's going on. 4803 4804 uhash_entries= [KNL,NET] 4805 Set number of hash buckets for UDP/UDP-Lite connections 4806 4807 uhci-hcd.ignore_oc= 4808 [USB] Ignore overcurrent events (default N). 4809 Some badly-designed motherboards generate lots of 4810 bogus events, for ports that aren't wired to 4811 anything. Set this parameter to avoid log spamming. 4812 Note that genuine overcurrent events won't be 4813 reported either. 4814 4815 unknown_nmi_panic 4816 [X86] Cause panic on unknown NMI. 4817 4818 usbcore.authorized_default= 4819 [USB] Default USB device authorization: 4820 (default -1 = authorized except for wireless USB, 4821 0 = not authorized, 1 = authorized, 2 = authorized 4822 if device connected to internal port) 4823 4824 usbcore.autosuspend= 4825 [USB] The autosuspend time delay (in seconds) used 4826 for newly-detected USB devices (default 2). This 4827 is the time required before an idle device will be 4828 autosuspended. Devices for which the delay is set 4829 to a negative value won't be autosuspended at all. 4830 4831 usbcore.usbfs_snoop= 4832 [USB] Set to log all usbfs traffic (default 0 = off). 4833 4834 usbcore.usbfs_snoop_max= 4835 [USB] Maximum number of bytes to snoop in each URB 4836 (default = 65536). 4837 4838 usbcore.blinkenlights= 4839 [USB] Set to cycle leds on hubs (default 0 = off). 4840 4841 usbcore.old_scheme_first= 4842 [USB] Start with the old device initialization 4843 scheme, applies only to low and full-speed devices 4844 (default 0 = off). 4845 4846 usbcore.usbfs_memory_mb= 4847 [USB] Memory limit (in MB) for buffers allocated by 4848 usbfs (default = 16, 0 = max = 2047). 4849 4850 usbcore.use_both_schemes= 4851 [USB] Try the other device initialization scheme 4852 if the first one fails (default 1 = enabled). 4853 4854 usbcore.initial_descriptor_timeout= 4855 [USB] Specifies timeout for the initial 64-byte 4856 USB_REQ_GET_DESCRIPTOR request in milliseconds 4857 (default 5000 = 5.0 seconds). 4858 4859 usbcore.nousb [USB] Disable the USB subsystem 4860 4861 usbcore.quirks= 4862 [USB] A list of quirk entries to augment the built-in 4863 usb core quirk list. List entries are separated by 4864 commas. Each entry has the form 4865 VendorID:ProductID:Flags. The IDs are 4-digit hex 4866 numbers and Flags is a set of letters. Each letter 4867 will change the built-in quirk; setting it if it is 4868 clear and clearing it if it is set. The letters have 4869 the following meanings: 4870 a = USB_QUIRK_STRING_FETCH_255 (string 4871 descriptors must not be fetched using 4872 a 255-byte read); 4873 b = USB_QUIRK_RESET_RESUME (device can't resume 4874 correctly so reset it instead); 4875 c = USB_QUIRK_NO_SET_INTF (device can't handle 4876 Set-Interface requests); 4877 d = USB_QUIRK_CONFIG_INTF_STRINGS (device can't 4878 handle its Configuration or Interface 4879 strings); 4880 e = USB_QUIRK_RESET (device can't be reset 4881 (e.g morph devices), don't use reset); 4882 f = USB_QUIRK_HONOR_BNUMINTERFACES (device has 4883 more interface descriptions than the 4884 bNumInterfaces count, and can't handle 4885 talking to these interfaces); 4886 g = USB_QUIRK_DELAY_INIT (device needs a pause 4887 during initialization, after we read 4888 the device descriptor); 4889 h = USB_QUIRK_LINEAR_UFRAME_INTR_BINTERVAL (For 4890 high speed and super speed interrupt 4891 endpoints, the USB 2.0 and USB 3.0 spec 4892 require the interval in microframes (1 4893 microframe = 125 microseconds) to be 4894 calculated as interval = 2 ^ 4895 (bInterval-1). 4896 Devices with this quirk report their 4897 bInterval as the result of this 4898 calculation instead of the exponent 4899 variable used in the calculation); 4900 i = USB_QUIRK_DEVICE_QUALIFIER (device can't 4901 handle device_qualifier descriptor 4902 requests); 4903 j = USB_QUIRK_IGNORE_REMOTE_WAKEUP (device 4904 generates spurious wakeup, ignore 4905 remote wakeup capability); 4906 k = USB_QUIRK_NO_LPM (device can't handle Link 4907 Power Management); 4908 l = USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL 4909 (Device reports its bInterval as linear 4910 frames instead of the USB 2.0 4911 calculation); 4912 m = USB_QUIRK_DISCONNECT_SUSPEND (Device needs 4913 to be disconnected before suspend to 4914 prevent spurious wakeup); 4915 n = USB_QUIRK_DELAY_CTRL_MSG (Device needs a 4916 pause after every control message); 4917 o = USB_QUIRK_HUB_SLOW_RESET (Hub needs extra 4918 delay after resetting its port); 4919 Example: quirks=0781:5580:bk,0a5c:5834:gij 4920 4921 usbhid.mousepoll= 4922 [USBHID] The interval which mice are to be polled at. 4923 4924 usbhid.jspoll= 4925 [USBHID] The interval which joysticks are to be polled at. 4926 4927 usbhid.kbpoll= 4928 [USBHID] The interval which keyboards are to be polled at. 4929 4930 usb-storage.delay_use= 4931 [UMS] The delay in seconds before a new device is 4932 scanned for Logical Units (default 1). 4933 4934 usb-storage.quirks= 4935 [UMS] A list of quirks entries to supplement or 4936 override the built-in unusual_devs list. List 4937 entries are separated by commas. Each entry has 4938 the form VID:PID:Flags where VID and PID are Vendor 4939 and Product ID values (4-digit hex numbers) and 4940 Flags is a set of characters, each corresponding 4941 to a common usb-storage quirk flag as follows: 4942 a = SANE_SENSE (collect more than 18 bytes 4943 of sense data); 4944 b = BAD_SENSE (don't collect more than 18 4945 bytes of sense data); 4946 c = FIX_CAPACITY (decrease the reported 4947 device capacity by one sector); 4948 d = NO_READ_DISC_INFO (don't use 4949 READ_DISC_INFO command); 4950 e = NO_READ_CAPACITY_16 (don't use 4951 READ_CAPACITY_16 command); 4952 f = NO_REPORT_OPCODES (don't use report opcodes 4953 command, uas only); 4954 g = MAX_SECTORS_240 (don't transfer more than 4955 240 sectors at a time, uas only); 4956 h = CAPACITY_HEURISTICS (decrease the 4957 reported device capacity by one 4958 sector if the number is odd); 4959 i = IGNORE_DEVICE (don't bind to this 4960 device); 4961 j = NO_REPORT_LUNS (don't use report luns 4962 command, uas only); 4963 l = NOT_LOCKABLE (don't try to lock and 4964 unlock ejectable media); 4965 m = MAX_SECTORS_64 (don't transfer more 4966 than 64 sectors = 32 KB at a time); 4967 n = INITIAL_READ10 (force a retry of the 4968 initial READ(10) command); 4969 o = CAPACITY_OK (accept the capacity 4970 reported by the device); 4971 p = WRITE_CACHE (the device cache is ON 4972 by default); 4973 r = IGNORE_RESIDUE (the device reports 4974 bogus residue values); 4975 s = SINGLE_LUN (the device has only one 4976 Logical Unit); 4977 t = NO_ATA_1X (don't allow ATA(12) and ATA(16) 4978 commands, uas only); 4979 u = IGNORE_UAS (don't bind to the uas driver); 4980 w = NO_WP_DETECT (don't test whether the 4981 medium is write-protected). 4982 y = ALWAYS_SYNC (issue a SYNCHRONIZE_CACHE 4983 even if the device claims no cache) 4984 Example: quirks=0419:aaf5:rl,0421:0433:rc 4985 4986 user_debug= [KNL,ARM] 4987 Format: <int> 4988 See arch/arm/Kconfig.debug help text. 4989 1 - undefined instruction events 4990 2 - system calls 4991 4 - invalid data aborts 4992 8 - SIGSEGV faults 4993 16 - SIGBUS faults 4994 Example: user_debug=31 4995 4996 userpte= 4997 [X86] Flags controlling user PTE allocations. 4998 4999 nohigh = do not allocate PTE pages in 5000 HIGHMEM regardless of setting 5001 of CONFIG_HIGHPTE. 5002 5003 vdso= [X86,SH] 5004 On X86_32, this is an alias for vdso32=. Otherwise: 5005 5006 vdso=1: enable VDSO (the default) 5007 vdso=0: disable VDSO mapping 5008 5009 vdso32= [X86] Control the 32-bit vDSO 5010 vdso32=1: enable 32-bit VDSO 5011 vdso32=0 or vdso32=2: disable 32-bit VDSO 5012 5013 See the help text for CONFIG_COMPAT_VDSO for more 5014 details. If CONFIG_COMPAT_VDSO is set, the default is 5015 vdso32=0; otherwise, the default is vdso32=1. 5016 5017 For compatibility with older kernels, vdso32=2 is an 5018 alias for vdso32=0. 5019 5020 Try vdso32=0 if you encounter an error that says: 5021 dl_main: Assertion `(void *) ph->p_vaddr == _rtld_local._dl_sysinfo_dso' failed! 5022 5023 vector= [IA-64,SMP] 5024 vector=percpu: enable percpu vector domain 5025 5026 video= [FB] Frame buffer configuration 5027 See Documentation/fb/modedb.rst. 5028 5029 video.brightness_switch_enabled= [0,1] 5030 If set to 1, on receiving an ACPI notify event 5031 generated by hotkey, video driver will adjust brightness 5032 level and then send out the event to user space through 5033 the allocated input device; If set to 0, video driver 5034 will only send out the event without touching backlight 5035 brightness level. 5036 default: 1 5037 5038 virtio_mmio.device= 5039 [VMMIO] Memory mapped virtio (platform) device. 5040 5041 <size>@<baseaddr>:<irq>[:<id>] 5042 where: 5043 <size> := size (can use standard suffixes 5044 like K, M and G) 5045 <baseaddr> := physical base address 5046 <irq> := interrupt number (as passed to 5047 request_irq()) 5048 <id> := (optional) platform device id 5049 example: 5050 virtio_mmio.device=1K@0x100b0000:48:7 5051 5052 Can be used multiple times for multiple devices. 5053 5054 vga= [BOOT,X86-32] Select a particular video mode 5055 See Documentation/x86/boot.rst and 5056 Documentation/svga.txt. 5057 Use vga=ask for menu. 5058 This is actually a boot loader parameter; the value is 5059 passed to the kernel using a special protocol. 5060 5061 vm_debug[=options] [KNL] Available with CONFIG_DEBUG_VM=y. 5062 May slow down system boot speed, especially when 5063 enabled on systems with a large amount of memory. 5064 All options are enabled by default, and this 5065 interface is meant to allow for selectively 5066 enabling or disabling specific virtual memory 5067 debugging features. 5068 5069 Available options are: 5070 P Enable page structure init time poisoning 5071 - Disable all of the above options 5072 5073 vmalloc=nn[KMG] [KNL,BOOT] Forces the vmalloc area to have an exact 5074 size of <nn>. This can be used to increase the 5075 minimum size (128MB on x86). It can also be used to 5076 decrease the size and leave more room for directly 5077 mapped kernel RAM. 5078 5079 vmcp_cma=nn[MG] [KNL,S390] 5080 Sets the memory size reserved for contiguous memory 5081 allocations for the vmcp device driver. 5082 5083 vmhalt= [KNL,S390] Perform z/VM CP command after system halt. 5084 Format: <command> 5085 5086 vmpanic= [KNL,S390] Perform z/VM CP command after kernel panic. 5087 Format: <command> 5088 5089 vmpoff= [KNL,S390] Perform z/VM CP command after power off. 5090 Format: <command> 5091 5092 vsyscall= [X86-64] 5093 Controls the behavior of vsyscalls (i.e. calls to 5094 fixed addresses of 0xffffffffff600x00 from legacy 5095 code). Most statically-linked binaries and older 5096 versions of glibc use these calls. Because these 5097 functions are at fixed addresses, they make nice 5098 targets for exploits that can control RIP. 5099 5100 emulate [default] Vsyscalls turn into traps and are 5101 emulated reasonably safely. 5102 5103 native Vsyscalls are native syscall instructions. 5104 This is a little bit faster than trapping 5105 and makes a few dynamic recompilers work 5106 better than they would in emulation mode. 5107 It also makes exploits much easier to write. 5108 5109 none Vsyscalls don't work at all. This makes 5110 them quite hard to use for exploits but 5111 might break your system. 5112 5113 vt.color= [VT] Default text color. 5114 Format: 0xYX, X = foreground, Y = background. 5115 Default: 0x07 = light gray on black. 5116 5117 vt.cur_default= [VT] Default cursor shape. 5118 Format: 0xCCBBAA, where AA, BB, and CC are the same as 5119 the parameters of the <Esc>[?A;B;Cc escape sequence; 5120 see VGA-softcursor.txt. Default: 2 = underline. 5121 5122 vt.default_blu= [VT] 5123 Format: <blue0>,<blue1>,<blue2>,...,<blue15> 5124 Change the default blue palette of the console. 5125 This is a 16-member array composed of values 5126 ranging from 0-255. 5127 5128 vt.default_grn= [VT] 5129 Format: <green0>,<green1>,<green2>,...,<green15> 5130 Change the default green palette of the console. 5131 This is a 16-member array composed of values 5132 ranging from 0-255. 5133 5134 vt.default_red= [VT] 5135 Format: <red0>,<red1>,<red2>,...,<red15> 5136 Change the default red palette of the console. 5137 This is a 16-member array composed of values 5138 ranging from 0-255. 5139 5140 vt.default_utf8= 5141 [VT] 5142 Format=<0|1> 5143 Set system-wide default UTF-8 mode for all tty's. 5144 Default is 1, i.e. UTF-8 mode is enabled for all 5145 newly opened terminals. 5146 5147 vt.global_cursor_default= 5148 [VT] 5149 Format=<-1|0|1> 5150 Set system-wide default for whether a cursor 5151 is shown on new VTs. Default is -1, 5152 i.e. cursors will be created by default unless 5153 overridden by individual drivers. 0 will hide 5154 cursors, 1 will display them. 5155 5156 vt.italic= [VT] Default color for italic text; 0-15. 5157 Default: 2 = green. 5158 5159 vt.underline= [VT] Default color for underlined text; 0-15. 5160 Default: 3 = cyan. 5161 5162 watchdog timers [HW,WDT] For information on watchdog timers, 5163 see Documentation/watchdog/watchdog-parameters.txt 5164 or other driver-specific files in the 5165 Documentation/watchdog/ directory. 5166 5167 watchdog_thresh= 5168 [KNL] 5169 Set the hard lockup detector stall duration 5170 threshold in seconds. The soft lockup detector 5171 threshold is set to twice the value. A value of 0 5172 disables both lockup detectors. Default is 10 5173 seconds. 5174 5175 workqueue.watchdog_thresh= 5176 If CONFIG_WQ_WATCHDOG is configured, workqueue can 5177 warn stall conditions and dump internal state to 5178 help debugging. 0 disables workqueue stall 5179 detection; otherwise, it's the stall threshold 5180 duration in seconds. The default value is 30 and 5181 it can be updated at runtime by writing to the 5182 corresponding sysfs file. 5183 5184 workqueue.disable_numa 5185 By default, all work items queued to unbound 5186 workqueues are affine to the NUMA nodes they're 5187 issued on, which results in better behavior in 5188 general. If NUMA affinity needs to be disabled for 5189 whatever reason, this option can be used. Note 5190 that this also can be controlled per-workqueue for 5191 workqueues visible under /sys/bus/workqueue/. 5192 5193 workqueue.power_efficient 5194 Per-cpu workqueues are generally preferred because 5195 they show better performance thanks to cache 5196 locality; unfortunately, per-cpu workqueues tend to 5197 be more power hungry than unbound workqueues. 5198 5199 Enabling this makes the per-cpu workqueues which 5200 were observed to contribute significantly to power 5201 consumption unbound, leading to measurably lower 5202 power usage at the cost of small performance 5203 overhead. 5204 5205 The default value of this parameter is determined by 5206 the config option CONFIG_WQ_POWER_EFFICIENT_DEFAULT. 5207 5208 workqueue.debug_force_rr_cpu 5209 Workqueue used to implicitly guarantee that work 5210 items queued without explicit CPU specified are put 5211 on the local CPU. This guarantee is no longer true 5212 and while local CPU is still preferred work items 5213 may be put on foreign CPUs. This debug option 5214 forces round-robin CPU selection to flush out 5215 usages which depend on the now broken guarantee. 5216 When enabled, memory and cache locality will be 5217 impacted. 5218 5219 x2apic_phys [X86-64,APIC] Use x2apic physical mode instead of 5220 default x2apic cluster mode on platforms 5221 supporting x2apic. 5222 5223 x86_intel_mid_timer= [X86-32,APBT] 5224 Choose timer option for x86 Intel MID platform. 5225 Two valid options are apbt timer only and lapic timer 5226 plus one apbt timer for broadcast timer. 5227 x86_intel_mid_timer=apbt_only | lapic_and_apbt 5228 5229 xen_512gb_limit [KNL,X86-64,XEN] 5230 Restricts the kernel running paravirtualized under Xen 5231 to use only up to 512 GB of RAM. The reason to do so is 5232 crash analysis tools and Xen tools for doing domain 5233 save/restore/migration must be enabled to handle larger 5234 domains. 5235 5236 xen_emul_unplug= [HW,X86,XEN] 5237 Unplug Xen emulated devices 5238 Format: [unplug0,][unplug1] 5239 ide-disks -- unplug primary master IDE devices 5240 aux-ide-disks -- unplug non-primary-master IDE devices 5241 nics -- unplug network devices 5242 all -- unplug all emulated devices (NICs and IDE disks) 5243 unnecessary -- unplugging emulated devices is 5244 unnecessary even if the host did not respond to 5245 the unplug protocol 5246 never -- do not unplug even if version check succeeds 5247 5248 xen_nopvspin [X86,XEN] 5249 Disables the ticketlock slowpath using Xen PV 5250 optimizations. 5251 5252 xen_nopv [X86] 5253 Disables the PV optimizations forcing the HVM guest to 5254 run as generic HVM guest with no PV drivers. 5255 5256 xen_scrub_pages= [XEN] 5257 Boolean option to control scrubbing pages before giving them back 5258 to Xen, for use by other domains. Can be also changed at runtime 5259 with /sys/devices/system/xen_memory/xen_memory0/scrub_pages. 5260 Default value controlled with CONFIG_XEN_SCRUB_PAGES_DEFAULT. 5261 5262 xen_timer_slop= [X86-64,XEN] 5263 Set the timer slop (in nanoseconds) for the virtual Xen 5264 timers (default is 100000). This adjusts the minimum 5265 delta of virtualized Xen timers, where lower values 5266 improve timer resolution at the expense of processing 5267 more timer interrupts. 5268 5269 xirc2ps_cs= [NET,PCMCIA] 5270 Format: 5271 <irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]] 5272 5273 xhci-hcd.quirks [USB,KNL] 5274 A hex value specifying bitmask with supplemental xhci 5275 host controller quirks. Meaning of each bit can be 5276 consulted in header drivers/usb/host/xhci.h. 5277