raidctl -C "disks" [-r raid_level] [-z capacity] [-s stripe_size] [-f]
 controller

raidctl -d [-f] volume

raidctl -F filename [-f] controller.\|.\|.

raidctl -a {set | unset} -g disk {volume | controller}

raidctl -p "param=value" [-f] volume

raidctl -c [-f] [-r raid_level] disk1 disk2 [disk3...]

raidctl -l -g disk controller

raidctl -l volume

raidctl -l controller.\|.\|.

raidctl [-l]

raidctl -S [volume | controller]

raidctl -S -g disk controller

raidctl -h

The raidctl utility is a hardware RAID configuration tool that supports different RAID controllers by providing a CLI (command-line interface) to end-users to create, delete or display RAID volume(s). The utility can also used to set properties of a volume, assign hot-spare (HSP) disks to volumes or controllers, and to update firmware/fcode/BIOS for RAID controllers.

The raidctl utility requires privileges that are controlled by the underlying file-system permissions. Only privileged users can manipulate the RAID system configuration. If a non-privileged user attempts to run raidctl, the command fails with an exit status of 1.

The raidctl utility, as described in this man page, defines a broad set of command line options to provide management for full-featured RAID controllers. However, support for a given option depends on two elements:

The dependency on a software driver is due to the design of raidctl. The utility is built on a common library that enables the insertion of plug-in modules for different drivers. Currently, the Solaris operating system is shipped with a plug-in for the mpt driver. This plug-in does not support all of the raidctl options. On a given storage device, options might be further limited by the device's firmware level.

The level of support for the various raidctl options cannot be determined by raidctl. The user must rely on the documentation for his RAID controller or hardware platform.

Currently, raidctl Currently, raidctl provides some level of support for the following RAID controllers:

All of the above HBAs are maintained by the mpt driver, on X86-32/64 and SPARC platforms.

The following options are supported: -C "disks" [-r raid_level] [-z capacity] [-s stripe_size] [-f] controller

Example 1 Creating the RAID Configuration

The following command creates a RAID 0 volume of 10G on controller 0, and the stripe size will be set to 64k:

# raidctl -C "0.0.0 0.2.0" -r 0 -z 10g -s 64k 0

The following command creates a RAID 1 volume on controller 2:

# raidctl -C "0.0.0 1.1.0" -r 1 2

The following command creates a RAID 5 volume on controller 2:

# raidctl -C "0.0.0 0.1.0 0.2.0" -r 5 2

The following command creates a RAID 10 volume on controller 0:

# raidctl -C "(0.0.0 0.1.0)(0.2.0 0.3.0)" -r 10 0

The following command creates a RAID 50 volume on controller 0:

# raidctl -C "(0.0.0 0.1.0 0.2.0)(0.3.0 0.4.0 0.5.0)" -r 50 0

Example 2 Displaying the RAID Configuration

The following command displays all available controllers, volumes, and disks:

# raidctl -l

Controller: 0
Controller: 2
 Volume:c2t0d0
 Disk: 0.0.0
 Disk: 0.1.0
 Disk: 0.2.0
 Disk: 0.3.0(HSP)

The following command displays information about controller 2:

# raidctl -l 2

Controller Type Fw_version
--------------------------------------------------------------
c2 LSI 1030 1.03.39.00

The following command displays information about the specified volume:

# raidctl -l c2t0d0

Volume Size Stripe Status Cache RAID
 Sub Size Level
 Disk
--------------------------------------------------------------
c2t0d0 10240M 64K OPTIMAL ON RAID5
 0.0.0 5120M GOOD
 0.1.0 5120M GOOD
 0.2.0 5120M GOOD

The following command displays information about disk 0.0.0 on controller 0:

# raidctl -l -g 0.0.0 0

Disk Vendor Product Firmware Capacity Status HSP
--------------------------------------------------------------------
0.0.0 HITACHI H101473SCSUN72G SQ02 68.3G GOOD N/A
GUID:2000000cca02536c

Example 3 Deleting the RAID Configuration

The following command deletes a volume:

# raidctl -d c0t0d0

Example 4 Updating Flash Images on the Controller

The following command updates flash images on the controller 0:

# raidctl -F lsi_image.fw 0

Example 5 Setting or Unsetting a Hot-Spare Disk

The following command sets disk 0.3.0 on controller 2 as a global hot-spare disk:

# raidctl -a set -g 0.3.0 2

The following command sets disk 0.3.0 on controller 2 as a local hot-spare disk to volume c2t0d0:

# raidctl -a set -g 0.3.0 c2t0d0

The following command converts disk 0.3.0 on controller 2 from a global hot-spare disk to a normal one:

# raidctl -a unset -g 0.3.0 2

The following command removes disk 0.3.0 from being a local hot-spare disk from volume c2t0d0:

# raidctl -a unset -g 0.3.0 c2t0d0

Example 6 Setting the Volume's Property

The following command sets the write policy of the volume to "off":

# raidctl -a set -p "wp=off" c0t0d0

Example 7 Creating Volumes with the -c Option

The following command creates a RAID 1 volume:

# raidctl -c c0t0d0 c0t1d0

The following command creates a RAID 0 volume:

# raidctl -c -r 0 c0t1d0 c0t2d0 c0t3d0

Example 8 Taking a Snapshot of the RAID Configuration

The following command takes a snapshot of all RAID devices:

# # raidctl -S

1 "LSI 1030"
c1t1d0 2 0.2.0 0.3.0 1 DEGRADED
0.2.0 GOOD
0.3.0 FAILED

The following command takes a snapshot about volume c1t0d0:

# raidctl -S c1t0d0

c1t0d0 2 0.0.0 0.1.0 1 OPTIMAL

The following command takes a snapshot about disk 0.1.0 on controller 1:

# raidctl -S -g 0.1.0 1

0.1.0 GOOD

The following exit values are returned: 0

See attributes(7) for descriptions of the following attributes:

mpt (4D), attributes (7)

System Administration Guide: Basic Administration

Do not create raid volumes on internal SAS disks if you are going to use the Solaris Multipathing I/O feature (also known as MPxIO). Creating a new raid volume under Solaris Multipathing will give your root device a new GUID which does not match the GUID for the existing devices. This will cause a boot failure since your root device entry in /etc/vfstab will not match.

The -z option is not supported on systems that use the mpt driver and LSI RAID controllers.