1# 2# NOTES -- Lines that can be cut/pasted into kernel and hints configs. 3# 4# This file contains machine dependent kernel configuration notes. For 5# machine independent notes, look in /sys/conf/NOTES. 6# 7# $FreeBSD$ 8# 9 10# 11# This directive is mandatory; it defines the architecture to be 12# configured for; in this case, the 386 family based IBM-PC and 13# compatibles. 14# 15machine i386 16 17# 18# We want LINT to cover profiling as well 19profile 2 20 21 22##################################################################### 23# SMP OPTIONS: 24# 25# APIC_IO enables the use of the IO APIC for Symmetric I/O. 26# 27# Notes: 28# 29# An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard. 30# 31# Be sure to disable 'cpu I386_CPU' && 'cpu I486_CPU' for SMP kernels. 32# 33# Check the 'Rogue SMP hardware' section to see if additional options 34# are required by your hardware. 35# 36 37# Mandatory: 38options APIC_IO # Symmetric (APIC) I/O 39 40# 41# Rogue SMP hardware: 42# 43 44# Bridged PCI cards: 45# 46# The MP tables of most of the current generation MP motherboards 47# do NOT properly support bridged PCI cards. To use one of these 48# cards you should refer to ??? 49 50 51##################################################################### 52# CPU OPTIONS 53 54# 55# You must specify at least one CPU (the one you intend to run on); 56# deleting the specification for CPUs you don't need to use may make 57# parts of the system run faster. 58# I386_CPU is mutually exclusive with the other CPU types. 59# 60#cpu I386_CPU 61cpu I486_CPU 62cpu I586_CPU # aka Pentium(tm) 63cpu I686_CPU # aka Pentium Pro(tm) 64 65# 66# Options for CPU features. 67# 68# CPU_ATHLON_SSE_HACK tries to enable SSE instructions when the BIOS has 69# forgotten to enable them. 70# 71# CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM 72# BlueLightning CPU. It works only with Cyrix FPU, and this option 73# should not be used with Intel FPU. 74# 75# CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning 76# CPU if CPU supports it. The default is double-clock mode on 77# BlueLightning CPU box. 78# 79# CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1). 80# 81# CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct 82# mapped mode. Default is 2-way set associative mode. 83# 84# CPU_CYRIX_NO_LOCK enables weak locking for the entire address space 85# of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1. 86# Otherwise, the NO_LOCK bit of CCR1 is cleared. (NOTE 3) 87# 88# CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables 89# reorder). This option should not be used if you use memory mapped 90# I/O device(s). 91# 92# CPU_ELAN enables support for AMDs ElanSC520 CPU. 93# 94# CPU_ENABLE_SSE enables SSE/MMX2 instructions support. This is default 95# on I686_CPU and above. 96# CPU_DISABLE_SSE explicitly prevent I686_CPU from turning on SSE. 97# 98# CPU_FASTER_5X86_FPU enables faster FPU exception handler. 99# 100# CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products 101# for i386 machines. 102# 103# CPU_IORT defines I/O clock delay time (NOTE 1). Default values of 104# I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively 105# (no clock delay). 106# 107# CPU_L2_LATENCY specifed the L2 cache latency value. This option is used 108# only when CPU_PPRO2CELERON is defined and Mendocino Celeron is detected. 109# The default value is 5. 110# 111# CPU_LOOP_EN prevents flushing the prefetch buffer if the destination 112# of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE 113# 1). 114# 115# CPU_PPRO2CELERON enables L2 cache of Mendocino Celeron CPUs. This option 116# is useful when you use Socket 8 to Socket 370 converter, because most Pentium 117# Pro BIOSs do not enable L2 cache of Mendocino Celeron CPUs. 118# 119# CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1). 120# 121# CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU 122# enters suspend mode following execution of HALT instruction. 123# 124# CPU_UPGRADE_HW_CACHE eliminates unneeded cache flush instruction(s). 125# 126# CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD 127# K5/K6/K6-2 cpus. 128# 129# CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache 130# flush at hold state. 131# 132# CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs 133# without cache flush at hold state, and (2) write-back CPU cache on 134# Cyrix 6x86 whose revision < 2.7 (NOTE 2). 135# 136# NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY 137# Pentiums) from locking up when a LOCK CMPXCHG8B instruction is 138# executed. This option is only needed if I586_CPU is also defined, 139# and should be included for any non-Pentium CPU that defines it. 140# 141# NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors 142# which indicates that the 15-16MB range is *definitely* not being 143# occupied by an ISA memory hole. 144# 145# CPU_DISABLE_CMPXCHG disables the CMPXCHG instruction on > i386 IA32 146# machines. VmWare seems to emulate this instruction poorly, causing 147# the guest OS to run very slowly. Enabling this with a SMP kernel 148# will cause the kernel to be unusable. 149# 150# NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT, 151# CPU_LOOP_EN and CPU_RSTK_EN should not be used because of CPU bugs. 152# These options may crash your system. 153# 154# NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled 155# in write-through mode when revision < 2.7. If revision of Cyrix 156# 6x86 >= 2.7, CPU cache is always enabled in write-back mode. 157# 158# NOTE 3: This option may cause failures for software that requires 159# locked cycles in order to operate correctly. 160# 161options CPU_ATHLON_SSE_HACK 162options CPU_BLUELIGHTNING_FPU_OP_CACHE 163options CPU_BLUELIGHTNING_3X 164options CPU_BTB_EN 165options CPU_DIRECT_MAPPED_CACHE 166options CPU_DISABLE_5X86_LSSER 167options CPU_ELAN 168options CPU_ENABLE_SSE 169#options CPU_DISABLE_SSE 170options CPU_FASTER_5X86_FPU 171options CPU_I486_ON_386 172options CPU_IORT 173options CPU_L2_LATENCY=5 174options CPU_LOOP_EN 175options CPU_PPRO2CELERON 176options CPU_RSTK_EN 177options CPU_SUSP_HLT 178options CPU_UPGRADE_HW_CACHE 179options CPU_WT_ALLOC 180options CYRIX_CACHE_WORKS 181options CYRIX_CACHE_REALLY_WORKS 182#options NO_F00F_HACK 183options CPU_DISABLE_CMPXCHG 184 185# 186# A math emulator is mandatory if you wish to run on hardware which 187# does not have a floating-point processor. Pick either the original, 188# bogus (but freely-distributable) math emulator, or a much more 189# fully-featured but GPL-licensed emulator taken from Linux. 190# 191options MATH_EMULATE #Support for x87 emulation 192# Don't enable both of these in a real config. 193options GPL_MATH_EMULATE #Support for x87 emulation via 194 #new math emulator 195 196# 197# PERFMON causes the driver for Pentium/Pentium Pro performance counters 198# to be compiled. See perfmon(4) for more information. 199# 200options PERFMON 201 202 203##################################################################### 204# NETWORKING OPTIONS 205 206# 207# DEVICE_POLLING adds support for mixed interrupt-polling handling 208# of network device drivers, which has significant benefits in terms 209# of robustness to overloads and responsivity, as well as permitting 210# accurate scheduling of the CPU time between kernel network processing 211# and other activities. The drawback is a moderate (up to 1/HZ seconds) 212# potential increase in response times. 213# It is strongly recommended to use HZ=1000 or 2000 with DEVICE_POLLING 214# to achieve smoother behaviour. 215# Additionally, you can enable/disable polling at runtime with the 216# sysctl variable kern.polling.enable (defaults off), and select 217# the CPU fraction reserved to userland with the sysctl variable 218# kern.polling.user_frac (default 50, range 0..100). 219# 220# Only the "dc" "fxp" and "sis" devices support this mode of operation at 221# the time of this writing. 222 223options DEVICE_POLLING 224 225 226##################################################################### 227# CLOCK OPTIONS 228 229# The following options are used for debugging clock behavior only, and 230# should not be used for production systems. 231# 232# CLK_CALIBRATION_LOOP will run the clock calibration loop at startup 233# until the user presses a key. 234 235options CLK_CALIBRATION_LOOP 236 237# The following two options measure the frequency of the corresponding 238# clock relative to the RTC (onboard mc146818a). 239 240options CLK_USE_I8254_CALIBRATION 241options CLK_USE_TSC_CALIBRATION 242 243 244##################################################################### 245# MISCELLANEOUS DEVICES AND OPTIONS 246 247device speaker #Play IBM BASIC-style noises out your speaker 248hint.atspeaker.0.at="isa" 249hint.atspeaker.0.port="0x61" 250device gzip #Exec gzipped a.out's. REQUIRES COMPAT_AOUT! 251device apm_saver # Requires APM 252 253 254##################################################################### 255# HARDWARE BUS CONFIGURATION 256 257# 258# ISA bus 259# 260device isa 261 262# 263# Options for `isa': 264# 265# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A 266# interrupt controller. This saves about 0.7-1.25 usec for each interrupt. 267# This option breaks suspend/resume on some portables. 268# 269# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A 270# interrupt controller. This saves about 0.7-1.25 usec for each interrupt. 271# Automatic EOI is documented not to work for for the slave with the 272# original i8259A, but it works for some clones and some integrated 273# versions. 274# 275# MAXMEM specifies the amount of RAM on the machine; if this is not 276# specified, FreeBSD will first read the amount of memory from the CMOS 277# RAM, so the amount of memory will initially be limited to 64MB or 16MB 278# depending on the BIOS. If the BIOS reports 64MB, a memory probe will 279# then attempt to detect the installed amount of RAM. If this probe 280# fails to detect >64MB RAM you will have to use the MAXMEM option. 281# The amount is in kilobytes, so for a machine with 128MB of RAM, it would 282# be 131072 (128 * 1024). 283# 284# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to 285# reset the CPU for reboot. This is needed on some systems with broken 286# keyboard controllers. 287 288options COMPAT_OLDISA #Use ISA shims and glue for old drivers 289options AUTO_EOI_1 290#options AUTO_EOI_2 291 292options MAXMEM=(128*1024) 293#options BROKEN_KEYBOARD_RESET 294 295# 296# EISA bus 297# 298# The EISA bus device is `eisa'. It provides auto-detection and 299# configuration support for all devices on the EISA bus. 300 301device eisa 302 303# By default, only 10 EISA slots are probed, since the slot numbers 304# above clash with the configuration address space of the PCI subsystem, 305# and the EISA probe is not very smart about this. This is sufficient 306# for most machines, but in particular the HP NetServer LC series comes 307# with an onboard AIC7770 dual-channel SCSI controller on EISA slot #11, 308# thus you need to bump this figure to 12 for them. 309options EISA_SLOTS=12 310 311# 312# MCA bus: 313# 314# The MCA bus device is `mca'. It provides auto-detection and 315# configuration support for all devices on the MCA bus. 316# No hints are required for MCA. 317 318device mca 319 320# 321# PCI bus & PCI options: 322# 323device pci 324 325# 326# AGP GART support 327device agp 328 329 330##################################################################### 331# HARDWARE DEVICE CONFIGURATION 332 333# 334# Mandatory devices: 335# 336 337# To include support for VGA VESA video modes 338options VESA 339 340# Turn on extra debugging checks and output for VESA support. 341options VESA_DEBUG 342 343# The pcvt console driver (vt220 compatible). 344device vt 345hint.vt.0.at="isa" 346options XSERVER # support for running an X server on vt 347options FAT_CURSOR # start with block cursor 348# This PCVT option is for keyboards such as those used on really old ThinkPads 349options PCVT_SCANSET=2 350# Other PCVT options are documented in pcvt(4). 351options PCVT_24LINESDEF 352options PCVT_CTRL_ALT_DEL 353options PCVT_META_ESC 354options PCVT_NSCREENS=9 355options PCVT_PRETTYSCRNS 356options PCVT_SCREENSAVER 357options PCVT_USEKBDSEC 358options PCVT_VT220KEYB 359options PCVT_GREENSAVER 360 361# 362# The Numeric Processing eXtension driver. In addition to this, you 363# may configure a math emulator (see above). If your machine has a 364# hardware FPU and the kernel configuration includes the npx device 365# *and* a math emulator compiled into the kernel, the hardware FPU 366# will be used, unless it is found to be broken or unless "flags" to 367# npx0 includes "0x08", which requests preference for the emulator. 368device npx 369hint.npx.0.flags="0x0" 370hint.npx.0.irq="13" 371 372# 373# `flags' for npx0: 374# 0x01 don't use the npx registers to optimize bcopy. 375# 0x02 don't use the npx registers to optimize bzero. 376# 0x04 don't use the npx registers to optimize copyin or copyout. 377# 0x08 use emulator even if hardware FPU is available. 378# The npx registers are normally used to optimize copying and zeroing when 379# all of the following conditions are satisfied: 380# I586_CPU is an option 381# the cpu is an i586 (perhaps not a Pentium) 382# the probe for npx0 succeeds 383# INT 16 exception handling works. 384# Then copying and zeroing using the npx registers is normally 30-100% faster. 385# The flags can be used to control cases where it doesn't work or is slower. 386# Setting them at boot time using userconfig works right (the optimizations 387# are not used until later in the bootstrap when npx0 is attached). 388# Flag 0x08 automatically disables the i586 optimized routines. 389# 390 391# 392# Optional devices: 393# 394 395# 396# ACPI support using the Intel ACPI Component Architecture reference 397# implementation. 398# 399# ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer 400# kernel environment variables to select initial debugging levels for the 401# Intel ACPICA code. (Note that the Intel code must also have USE_DEBUGGER 402# defined when it is built). 403# 404# Note that building ACPI into the kernel is deprecated; the module is 405# normally loaded automatically by the loader. 406# 407device acpi 408options ACPI_DEBUG 409 410# M-systems DiskOnchip products see src/sys/contrib/dev/fla/README 411device fla 412hint.fla.0.at="isa" 413 414# 415# mse: Logitech and ATI InPort bus mouse ports 416 417device mse 418hint.mse.0.at="isa" 419hint.mse.0.port="0x23c" 420hint.mse.0.irq="5" 421 422# 423# Network interfaces: 424# 425 426# cx: Cronyx/Sigma multiport sync/async (with Cisco or PPP framing) 427# el: 3Com 3C501 (slow!) 428# ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210; 429# Intel EtherExpress 430# le: Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100, 431# DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422) 432# oltr: Olicom ISA token-ring adapters OC-3115, OC-3117, OC-3118 and OC-3133 433# (no hints needed). 434# Olicom PCI token-ring adapters OC-3136, OC-3137, OC-3139, OC-3140, 435# OC-3141, OC-3540, OC-3250 436# rdp: RealTek RTL 8002-based pocket ethernet adapters 437# sbni: Granch SBNI12-xx ISA and PCI adapters 438# wl: Lucent Wavelan (ISA card only). 439 440# Order for ISA/EISA devices is important here 441 442device cx 1 443hint.cx.0.at="isa" 444hint.cx.0.port="0x240" 445hint.cx.0.irq="15" 446hint.cx.0.drq="7" 447device el 1 448hint.el.0.at="isa" 449hint.el.0.port="0x300" 450hint.el.0.irq="9" 451device ie 2 452hint.ie.0.at="isa" 453hint.ie.0.port="0x300" 454hint.ie.0.irq="5" 455hint.ie.0.maddr="0xd0000" 456hint.ie.1.at="isa" 457hint.ie.1.port="0x360" 458hint.ie.1.irq="7" 459hint.ie.1.maddr="0xd0000" 460device le 1 461hint.le.0.at="isa" 462hint.le.0.port="0x300" 463hint.le.0.irq="5" 464hint.le.0.maddr="0xd0000" 465device rdp 1 466hint.rdp.0.at="isa" 467hint.rdp.0.port="0x378" 468hint.rdp.0.irq="7" 469hint.rdp.0.flags="2" 470device sbni 471hint.sbni.0.at="isa" 472hint.sbni.0.port="0x210" 473hint.sbni.0.irq="0xefdead" 474hint.sbni.0.flags="0" 475device oltr 476hint.oltr.0.at="isa" 477device wl 478hint.wl.0.at="isa" 479hint.wl.0.port="0x300" 480options WLCACHE # enables the signal-strength cache 481options WLDEBUG # enables verbose debugging output 482 483# 484# Audio drivers: `pca' 485# 486# pca: PCM audio through your PC speaker 487 488device pca 489hint.pca.0.at="isa" 490hint.pca.0.port="0x040" 491 492# 493# SCSI host adapters: 494# 495# ncv: NCR 53C500 based SCSI host adapters. 496# nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters. 497# stg: TMC 18C30, 18C50 based SCSI host adapters. 498 499device ncv 500device nsp 501device stg 502hint.stg.0.at="isa" 503hint.stg.0.port="0x140" 504hint.stg.0.port="11" 505 506# 507# Adaptec FSA RAID controllers, including integrated DELL controllers, 508# the Dell PERC 2/QC and the HP NetRAID-4M 509device aac 510device aacp # SCSI Passthrough interface (optional, CAM required) 511 512# 513# Miscellaneous hardware: 514# 515# scd: Sony CD-ROM using proprietary (non-ATAPI) interface 516# wt: Wangtek and Archive QIC-02/QIC-36 tape drives 517# ctx: Cortex-I frame grabber 518# apm: Laptop Advanced Power Management (experimental) 519# pmtimer: Timer device driver for power management events (APM or ACPI) 520# spigot: The Creative Labs Video Spigot video-acquisition board 521# gp: National Instruments AT-GPIB and AT-GPIB/TNT board, PCMCIA-GPIB 522# asc: GI1904-based hand scanners, e.g. the Trust Amiscan Grey 523# gsc: Genius GS-4500 hand scanner. 524# rc: RISCom/8 multiport card 525# tw: TW-523 power line interface for use with X-10 home control products 526# spic: Sony Programmable I/O controller (VAIO notebooks) 527# stl: Stallion EasyIO and EasyConnection 8/32 (cd1400 based) 528# stli: Stallion EasyConnection 8/64, ONboard, Brumby (intelligent) 529# dgb: Digiboard PC/Xi and PC/Xe series driver (ALPHA QUALITY!) 530 531# Notes on APM 532# The flags takes the following meaning for apm0: 533# 0x0020 Statclock is broken. 534# If apm is omitted, some systems require sysctl kern.timecounter.method=1 535# for correct timekeeping. 536 537# Notes on the spigot: 538# The video spigot is at 0xad6. This port address can not be changed. 539# The irq values may only be 10, 11, or 15 540# I/O memory is an 8kb region. Possible values are: 541# 0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff 542# The start address must be on an even boundary. 543# Add the following option if you want to allow non-root users to be able 544# to access the spigot. This option is not secure because it allows users 545# direct access to the I/O page. 546# options SPIGOT_UNSECURE 547 548# Notes on the Specialix SI/XIO driver: 549# The host card is memory, not IO mapped. 550# The Rev 1 host cards use a 64K chunk, on a 32K boundary. 551# The Rev 2 host cards use a 32K chunk, on a 32K boundary. 552# The cards can use an IRQ of 11, 12 or 15. 553 554# Notes on the Sony Programmable I/O controller 555# This is a temporary driver that should someday be replaced by something 556# that hooks into the ACPI layer. The device is hooked to the PIIX4's 557# General Device 10 decoder, which means you have to fiddle with PCI 558# registers to map it in, even though it is otherwise treated here as 559# an ISA device. At the moment, the driver polls, although the device 560# is capable of generating interrupts. It largely undocumented. 561# The port location in the hint is where you WANT the device to be 562# mapped. 0x10a0 seems to be traditional. At the moment the jogdial 563# is the only thing truly supported, but aparently a fair percentage 564# of the Vaio extra features are controlled by this device. 565 566# Notes on the Stallion stl and stli drivers: 567# See src/i386/isa/README.stl for complete instructions. 568# This is version 0.0.5alpha, unsupported by Stallion. 569# The stl driver has a secondary IO port hard coded at 0x280. You need 570# to change src/i386/isa/stallion.c if you reconfigure this on the boards. 571# The "flags" and "msize" settings on the stli driver depend on the board: 572# EasyConnection 8/64 ISA: flags 23 msize 0x1000 573# EasyConnection 8/64 EISA: flags 24 msize 0x10000 574# EasyConnection 8/64 MCA: flags 25 msize 0x1000 575# ONboard ISA: flags 4 msize 0x10000 576# ONboard EISA: flags 7 msize 0x10000 577# ONboard MCA: flags 3 msize 0x10000 578# Brumby: flags 2 msize 0x4000 579# Stallion: flags 1 msize 0x10000 580 581# Notes on the Digiboard PC/Xi and PC/Xe series driver 582# 583# The NDGBPORTS option specifies the number of ports controlled by the 584# dgb(4) driver. The default value is 16 ports per device. 585 586# for the Sony CDU31/33A CDROM 587device scd 1 588hint.scd.0.at="isa" 589hint.scd.0.port="0x230" 590device wt 1 591hint.wt.0.at="isa" 592hint.wt.0.port="0x300" 593hint.wt.0.irq="5" 594hint.wt.0.drq="1" 595device ctx 1 596hint.ctx.0.at="isa" 597hint.ctx.0.port="0x230" 598hint.ctx.0.maddr="0xd0000" 599device spigot 1 600hint.spigot.0.at="isa" 601hint.spigot.0.port="0xad6" 602hint.spigot.0.irq="15" 603hint.spigot.0.maddr="0xee000" 604device apm 605hint.apm.0.flags="0x20" 606device pmtimer # Adjust system timer at wakeup time 607device gp 608hint.gp.0.at="isa" 609hint.gp.0.port="0x2c0" 610device gsc 1 611hint.gsc.0.at="isa" 612hint.gsc.0.port="0x270" 613hint.gsc.0.drq="3" 614device rc 615hint.rc.0.at="isa" 616hint.rc.0.port="0x220" 617hint.rc.0.irq="12" 618# the port and irq for tw0 are fictitious 619device tw 1 620hint.tw.0.at="isa" 621hint.tw.0.port="0x380" 622hint.tw.0.irq="11" 623device asc 1 624hint.asc.0.at="isa" 625hint.asc.0.port="0x3EB" 626hint.asc.0.drq="3" 627hint.asc.0.irq="10" 628device spic 629hint.spic.0.at="isa" 630hint.spic.0.port="0x10a0" 631device stl 632hint.stl.0.at="isa" 633hint.stl.0.port="0x2a0" 634hint.stl.0.irq="10" 635device stli 636hint.stli.0.at="isa" 637hint.stli.0.port="0x2a0" 638hint.stli.0.maddr="0xcc000" 639hint.stli.0.flags="23" 640hint.stli.0.msize="0x1000" 641device dgb 1 642options NDGBPORTS=17 643hint.dgb.0.at="isa" 644hint.dgb.0.port="0x220" 645hint.dgb.0.maddr="0xfc000" 646# You are unlikely to have the hardware for loran <phk@FreeBSD.org> 647device loran 648hint.loran.0.at="isa" 649hint.loran.0.irq="5" 650 651# 652# Laptop/Notebook options: 653# 654# See also: 655# apm under `Miscellaneous hardware' 656# above. 657 658# For older notebooks that signal a powerfail condition (external 659# power supply dropped, or battery state low) by issuing an NMI: 660 661options POWERFAIL_NMI # make it beep instead of panicing 662 663# 664# I2C Bus 665# 666# Philips i2c bus support is provided by the `iicbus' device. 667# 668# Supported interfaces: 669# pcf Philips PCF8584 ISA-bus controller 670# 671device pcf 672hint.pcf.0.at="isa" 673hint.pcf.0.port="0x320" 674hint.pcf.0.irq="5" 675 676#--------------------------------------------------------------------------- 677# ISDN4BSD 678# 679# See /usr/share/examples/isdn/ROADMAP for an introduction to isdn4bsd. 680# 681# i4b passive ISDN cards support contains the following hardware drivers: 682# 683# isic - Siemens/Infineon ISDN ISAC/HSCX/IPAC chipset driver 684# iwic - Winbond W6692 PCI bus ISDN S/T interface controller 685# ifpi - AVM Fritz!Card PCI driver 686# ifpi2 - AVM Fritz!Card PCI version 2 driver 687# ihfc - Cologne Chip HFC ISA/ISA-PnP chipset driver 688# ifpnp - AVM Fritz!Card PnP driver 689# itjc - Siemens ISAC / TJNet Tiger300/320 chipset 690# 691# i4b active ISDN cards support contains the following hardware drivers: 692# 693# iavc - AVM B1 PCI, AVM B1 ISA, AVM T1 694# 695# Note that the ``options'' (if given) and ``device'' lines must BOTH 696# be uncommented to enable support for a given card ! 697# 698# In addition to a hardware driver (and probably an option) the mandatory 699# ISDN protocol stack devices and the mandatory support device must be 700# enabled as well as one or more devices from the optional devices section. 701# 702#--------------------------------------------------------------------------- 703# isic driver (Siemens/Infineon chipsets) 704# 705device isic 706# 707# ISA bus non-PnP Cards: 708# ---------------------- 709# 710# Teles S0/8 or Niccy 1008 711options TEL_S0_8 712hint.isic.0.at="isa" 713hint.isic.0.maddr="0xd0000" 714hint.isic.0.irq="5" 715hint.isic.0.flags="1" 716# 717# Teles S0/16 or Creatix ISDN-S0 or Niccy 1016 718options TEL_S0_16 719hint.isic.0.at="isa" 720hint.isic.0.port="0xd80" 721hint.isic.0.maddr="0xd0000" 722hint.isic.0.irq="5" 723hint.isic.0.flags="2" 724# 725# Teles S0/16.3 726options TEL_S0_16_3 727hint.isic.0.at="isa" 728hint.isic.0.port="0xd80" 729hint.isic.0.irq="5" 730hint.isic.0.flags="3" 731# 732# AVM A1 or AVM Fritz!Card 733options AVM_A1 734hint.isic.0.at="isa" 735hint.isic.0.port="0x340" 736hint.isic.0.irq="5" 737hint.isic.0.flags="4" 738# 739# USRobotics Sportster ISDN TA intern 740options USR_STI 741hint.isic.0.at="isa" 742hint.isic.0.port="0x268" 743hint.isic.0.irq="5" 744hint.isic.0.flags="7" 745# 746# ITK ix1 Micro ( < V.3, non-PnP version ) 747options ITKIX1 748hint.isic.0.at="isa" 749hint.isic.0.port="0x398" 750hint.isic.0.irq="10" 751hint.isic.0.flags="18" 752# 753# ELSA PCC-16 754options ELSA_PCC16 755hint.isic.0.at="isa" 756hint.isic.0.port="0x360" 757hint.isic.0.irq="10" 758hint.isic.0.flags="20" 759# 760# ISA bus PnP Cards: 761# ------------------ 762# 763# Teles S0/16.3 PnP 764options TEL_S0_16_3_P 765# 766# Creatix ISDN-S0 P&P 767options CRTX_S0_P 768# 769# Dr. Neuhaus Niccy Go@ 770options DRN_NGO 771# 772# Sedlbauer Win Speed 773options SEDLBAUER 774# 775# Dynalink IS64PH 776options DYNALINK 777# 778# ELSA QuickStep 1000pro ISA 779options ELSA_QS1ISA 780# 781# Siemens I-Surf 2.0 782options SIEMENS_ISURF2 783# 784# Asuscom ISDNlink 128K ISA 785options ASUSCOM_IPAC 786# 787# Eicon Diehl DIVA 2.0 and 2.02 788options EICON_DIVA 789# 790# Compaq Microcom 610 ISDN card (Compaq series PSB2222I) 791options COMPAQ_M610 792# 793# PCI bus Cards: 794# -------------- 795# 796# Cyclades Cyclom-Y PCI serial driver 797device cy 1 798options CY_PCI_FASTINTR # Use with cy_pci unless irq is shared 799hint.cy.0.at="isa" 800hint.cy.0.irq="10" 801hint.cy.0.maddr="0xd4000" 802hint.cy.0.msize="0x2000" 803# 804#--------------------------------------------------------------------------- 805# ELSA MicroLink ISDN/PCI (same as ELSA QuickStep 1000pro PCI) 806options ELSA_QS1PCI 807# 808# 809#--------------------------------------------------------------------------- 810# ifpnp driver for AVM Fritz!Card PnP 811# 812# AVM Fritz!Card PnP 813device ifpnp 814# 815#--------------------------------------------------------------------------- 816# ihfc driver for Cologne Chip ISA chipsets (experimental!) 817# 818# Teles 16.3c ISA PnP 819# AcerISDN P10 ISA PnP 820# TELEINT ISDN SPEED No.1 821device ihfc 822# 823#--------------------------------------------------------------------------- 824# ifpi driver for AVM Fritz!Card PCI 825# 826# AVM Fritz!Card PCI 827device ifpi 828# 829#--------------------------------------------------------------------------- 830# ifpi2 driver for AVM Fritz!Card PCI version 2 831# 832# AVM Fritz!Card PCI version 2 833device "ifpi2" 834# 835#--------------------------------------------------------------------------- 836# iwic driver for Winbond W6692 chipset 837# 838# ASUSCOM P-IN100-ST-D (and other Winbond W6692 based cards) 839device iwic 840# 841#--------------------------------------------------------------------------- 842# itjc driver for Simens ISAC / TJNet Tiger300/320 chipset 843# 844# Traverse Technologies NETjet-S 845# Teles PCI-TJ 846device itjc 847# 848#--------------------------------------------------------------------------- 849# iavc driver (AVM active cards, needs i4bcapi driver!) 850# 851device iavc 852# 853# AVM B1 ISA bus (PnP mode not supported!) 854# ---------------------------------------- 855hint.iavc.0.at="isa" 856hint.iavc.0.port="0x150" 857hint.iavc.0.irq="5" 858# 859#--------------------------------------------------------------------------- 860# ISDN Protocol Stack - mandatory for all hardware drivers 861# 862# Q.921 / layer 2 - i4b passive cards D channel handling 863device "i4bq921" 864# 865# Q.931 / layer 3 - i4b passive cards D channel handling 866device "i4bq931" 867# 868# layer 4 - i4b common passive and active card handling 869device "i4b" 870# 871#--------------------------------------------------------------------------- 872# ISDN devices - mandatory for all hardware drivers 873# 874# userland driver to do ISDN tracing (for passive cards only) 875device "i4btrc" 4 876# 877# userland driver to control the whole thing 878device "i4bctl" 879# 880#--------------------------------------------------------------------------- 881# ISDN devices - optional 882# 883# userland driver for access to raw B channel 884device "i4brbch" 4 885# 886# userland driver for telephony 887device "i4btel" 2 888# 889# network driver for IP over raw HDLC ISDN 890device "i4bipr" 4 891# enable VJ header compression detection for ipr i/f 892options IPR_VJ 893# enable logging of the first n IP packets to isdnd (n=32 here) 894options IPR_LOG=32 895# 896# network driver for sync PPP over ISDN; requires an equivalent 897# number of sppp device to be configured 898device "i4bisppp" 4 899# 900# B-channel interface to the netgraph subsystem 901device "i4bing" 2 902# 903# CAPI driver needed for active ISDN cards (see iavc driver above) 904device "i4bcapi" 905# 906#--------------------------------------------------------------------------- 907 908# 909# Set the number of PV entries per process. Increasing this can 910# stop panics related to heavy use of shared memory. However, that can 911# (combined with large amounts of physical memory) cause panics at 912# boot time due the kernel running out of VM space. 913# 914# If you're tweaking this, you might also want to increase the sysctls 915# "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target". 916# 917# The value below is the one more than the default. 918# 919options PMAP_SHPGPERPROC=201 920 921# 922# Change the size of the kernel virtual address space. Due to 923# constraints in loader(8) on i386, this must be a multiple of 4. 924# 256 = 1 GB of kernel address space. Increasing this also causes 925# a reduction of the address space in user processes. 512 splits 926# the 4GB cpu address space in half (2GB user, 2GB kernel). 927# 928options KVA_PAGES=260 929 930 931##################################################################### 932# ABI Emulation 933 934# Enable iBCS2 runtime support for SCO and ISC binaries 935options IBCS2 936 937# Emulate spx device for client side of SVR3 local X interface 938options SPX_HACK 939 940# Enable Linux ABI emulation 941options COMPAT_LINUX 942 943# Enable i386 a.out binary support 944options COMPAT_AOUT 945 946# Enable the linux-like proc filesystem support (requires COMPAT_LINUX 947# and PSEUDOFS) 948options LINPROCFS 949 950# 951# SysVR4 ABI emulation 952# 953# The svr4 ABI emulator can be statically compiled into the kernel or loaded as 954# a KLD module. 955# The STREAMS network emulation code can also be compiled statically or as a 956# module. If loaded as a module, it must be loaded before the svr4 module 957# (the /usr/sbin/svr4 script does this for you). If compiling statically, 958# the `streams' device must be configured into any kernel which also 959# specifies COMPAT_SVR4. It is possible to have a statically-configured 960# STREAMS device and a dynamically loadable svr4 emulator; the /usr/sbin/svr4 961# script understands that it doesn't need to load the `streams' module under 962# those circumstances. 963# Caveat: At this time, `options KTRACE' is required for the svr4 emulator 964# (whether static or dynamic). 965# 966options COMPAT_SVR4 # build emulator statically 967options DEBUG_SVR4 # enable verbose debugging 968device streams # STREAMS network driver (required for svr4). 969 970 971##################################################################### 972# VM OPTIONS 973 974# Disable the 4 MByte page PSE CPU feature. The PSE feature allows the 975# kernel to use a 4 MByte pages to map the kernel instead of 4k pages. 976# This saves on the amount of memory needed for page tables needed to 977# map the kernel. You should only disable this feature as a temporary 978# workaround if you are having problems with it enabled. 979# 980#options DISABLE_PSE 981 982# Disable the global pages PGE CPU feature. The PGE feature allows pages 983# to be marked with the PG_G bit. TLB entries for these pages are not 984# flushed from the cache when %cr3 is reloaded. This can make context 985# switches less expensive. You should only disable this feature as a 986# temporary workaround if you are having problems with it enabled. 987# 988#options DISABLE_PG_G 989 990# KSTACK_PAGES is the number of memory pages to assign to the kernel 991# stack of each thread. 992 993options KSTACK_PAGES=3 994 995##################################################################### 996 997# More undocumented options for linting. 998# Note that documenting these are not considered an affront. 999 1000# PECOFF module (Win32 Execution Format) 1001options PECOFF_SUPPORT 1002options PECOFF_DEBUG 1003 1004options ENABLE_ALART 1005options I4B_SMP_WORKAROUND 1006options I586_PMC_GUPROF=0x70000 1007options KBDIO_DEBUG=2 1008options KBD_MAXRETRY=4 1009options KBD_MAXWAIT=6 1010options KBD_RESETDELAY=201 1011 1012options PSM_DEBUG=1 1013 1014options TIMER_FREQ=((14318182+6)/12) 1015 1016options VM_KMEM_SIZE 1017options VM_KMEM_SIZE_MAX 1018options VM_KMEM_SIZE_SCALE 1019 1020# Yet more undocumented options for linting. 1021options COMPAT_SUNOS 1022