1 /* 2 * Copyright (c) 2014 The DragonFly Project. All rights reserved. 3 * 4 * This code is derived from software contributed to The DragonFly Project 5 * by Matthew Dillon <dillon@backplane.com> and was subsequently ported 6 * to FreeBSD by Michael Gmelin <freebsd@grem.de> 7 * 8 * Redistribution and use in source and binary forms, with or without 9 * modification, are permitted provided that the following conditions 10 * are met: 11 * 12 * 1. Redistributions of source code must retain the above copyright 13 * notice, this list of conditions and the following disclaimer. 14 * 2. Redistributions in binary form must reproduce the above copyright 15 * notice, this list of conditions and the following disclaimer in 16 * the documentation and/or other materials provided with the 17 * distribution. 18 * 3. Neither the name of The DragonFly Project nor the names of its 19 * contributors may be used to endorse or promote products derived 20 * from this software without specific, prior written permission. 21 * 22 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 23 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 24 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS 25 * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE 26 * COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, 27 * INCIDENTAL, SPECIAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES (INCLUDING, 28 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; 29 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED 30 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, 31 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT 32 * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 33 * SUCH DAMAGE. 34 */ 35 36 #include <sys/cdefs.h> 37 __FBSDID("$FreeBSD$"); 38 39 /* 40 * Intel fourth generation mobile cpus integrated I2C device. 41 * 42 * See ig4_reg.h for datasheet reference and notes. 43 * See ig4_var.h for locking semantics. 44 */ 45 46 #include "opt_acpi.h" 47 48 #include <sys/param.h> 49 #include <sys/systm.h> 50 #include <sys/kernel.h> 51 #include <sys/module.h> 52 #include <sys/errno.h> 53 #include <sys/kdb.h> 54 #include <sys/lock.h> 55 #include <sys/mutex.h> 56 #include <sys/proc.h> 57 #include <sys/sx.h> 58 #include <sys/syslog.h> 59 #include <sys/bus.h> 60 #include <sys/sysctl.h> 61 62 #include <machine/bus.h> 63 #include <sys/rman.h> 64 65 #ifdef DEV_ACPI 66 #include <contrib/dev/acpica/include/acpi.h> 67 #include <contrib/dev/acpica/include/accommon.h> 68 #include <dev/acpica/acpivar.h> 69 #endif 70 71 #include <dev/iicbus/iicbus.h> 72 #include <dev/iicbus/iiconf.h> 73 74 #include <dev/ichiic/ig4_reg.h> 75 #include <dev/ichiic/ig4_var.h> 76 77 #define DO_POLL(sc) (cold || kdb_active || SCHEDULER_STOPPED() || sc->poll) 78 79 /* 80 * tLOW, tHIGH periods of the SCL clock and maximal falling time of both 81 * lines are taken from I2C specifications. 82 */ 83 #define IG4_SPEED_STD_THIGH 4000 /* nsec */ 84 #define IG4_SPEED_STD_TLOW 4700 /* nsec */ 85 #define IG4_SPEED_STD_TF_MAX 300 /* nsec */ 86 #define IG4_SPEED_FAST_THIGH 600 /* nsec */ 87 #define IG4_SPEED_FAST_TLOW 1300 /* nsec */ 88 #define IG4_SPEED_FAST_TF_MAX 300 /* nsec */ 89 90 /* 91 * Ig4 hardware parameters except Haswell are taken from intel_lpss driver 92 */ 93 static const struct ig4_hw ig4iic_hw[] = { 94 [IG4_HASWELL] = { 95 .ic_clock_rate = 100, /* MHz */ 96 .sda_hold_time = 90, /* nsec */ 97 .txfifo_depth = 32, 98 .rxfifo_depth = 32, 99 }, 100 [IG4_ATOM] = { 101 .ic_clock_rate = 100, 102 .sda_fall_time = 280, 103 .scl_fall_time = 240, 104 .sda_hold_time = 60, 105 .txfifo_depth = 32, 106 .rxfifo_depth = 32, 107 }, 108 [IG4_SKYLAKE] = { 109 .ic_clock_rate = 120, 110 .sda_hold_time = 230, 111 }, 112 [IG4_APL] = { 113 .ic_clock_rate = 133, 114 .sda_fall_time = 171, 115 .scl_fall_time = 208, 116 .sda_hold_time = 207, 117 }, 118 [IG4_CANNONLAKE] = { 119 .ic_clock_rate = 216, 120 .sda_hold_time = 230, 121 }, 122 [IG4_TIGERLAKE] = { 123 .ic_clock_rate = 133, 124 .sda_fall_time = 171, 125 .scl_fall_time = 208, 126 .sda_hold_time = 42, 127 }, 128 [IG4_GEMINILAKE] = { 129 .ic_clock_rate = 133, 130 .sda_fall_time = 171, 131 .scl_fall_time = 290, 132 .sda_hold_time = 313, 133 }, 134 }; 135 136 static int ig4iic_set_config(ig4iic_softc_t *sc, bool reset); 137 static driver_filter_t ig4iic_intr; 138 static void ig4iic_dump(ig4iic_softc_t *sc); 139 140 static int ig4_dump; 141 SYSCTL_INT(_debug, OID_AUTO, ig4_dump, CTLFLAG_RW, 142 &ig4_dump, 0, "Dump controller registers"); 143 144 /* 145 * Clock registers initialization control 146 * 0 - Try read clock registers from ACPI and fallback to p.1. 147 * 1 - Calculate values based on controller type (IC clock rate). 148 * 2 - Use values inherited from DragonflyBSD driver (old behavior). 149 * 3 - Keep clock registers intact. 150 */ 151 static int ig4_timings; 152 SYSCTL_INT(_debug, OID_AUTO, ig4_timings, CTLFLAG_RDTUN, &ig4_timings, 0, 153 "Controller timings 0=ACPI, 1=predefined, 2=legacy, 3=do not change"); 154 155 /* 156 * Low-level inline support functions 157 */ 158 static __inline void 159 reg_write(ig4iic_softc_t *sc, uint32_t reg, uint32_t value) 160 { 161 bus_write_4(sc->regs_res, reg, value); 162 bus_barrier(sc->regs_res, reg, 4, BUS_SPACE_BARRIER_WRITE); 163 } 164 165 static __inline uint32_t 166 reg_read(ig4iic_softc_t *sc, uint32_t reg) 167 { 168 uint32_t value; 169 170 bus_barrier(sc->regs_res, reg, 4, BUS_SPACE_BARRIER_READ); 171 value = bus_read_4(sc->regs_res, reg); 172 return (value); 173 } 174 175 static void 176 ig4iic_set_intr_mask(ig4iic_softc_t *sc, uint32_t val) 177 { 178 if (sc->intr_mask != val) { 179 reg_write(sc, IG4_REG_INTR_MASK, val); 180 sc->intr_mask = val; 181 } 182 } 183 184 static int 185 intrstat2iic(ig4iic_softc_t *sc, uint32_t val) 186 { 187 uint32_t src; 188 189 if (val & IG4_INTR_RX_UNDER) 190 reg_read(sc, IG4_REG_CLR_RX_UNDER); 191 if (val & IG4_INTR_RX_OVER) 192 reg_read(sc, IG4_REG_CLR_RX_OVER); 193 if (val & IG4_INTR_TX_OVER) 194 reg_read(sc, IG4_REG_CLR_TX_OVER); 195 196 if (val & IG4_INTR_TX_ABRT) { 197 src = reg_read(sc, IG4_REG_TX_ABRT_SOURCE); 198 reg_read(sc, IG4_REG_CLR_TX_ABORT); 199 /* User-requested abort. Not really a error */ 200 if (src & IG4_ABRTSRC_TRANSFER) 201 return (IIC_ESTATUS); 202 /* Master has lost arbitration */ 203 if (src & IG4_ABRTSRC_ARBLOST) 204 return (IIC_EBUSBSY); 205 /* Did not receive an acknowledge from the remote slave */ 206 if (src & (IG4_ABRTSRC_TXNOACK_ADDR7 | 207 IG4_ABRTSRC_TXNOACK_ADDR10_1 | 208 IG4_ABRTSRC_TXNOACK_ADDR10_2 | 209 IG4_ABRTSRC_TXNOACK_DATA | 210 IG4_ABRTSRC_GENCALL_NOACK)) 211 return (IIC_ENOACK); 212 /* Programming errors */ 213 if (src & (IG4_ABRTSRC_GENCALL_READ | 214 IG4_ABRTSRC_NORESTART_START | 215 IG4_ABRTSRC_NORESTART_10)) 216 return (IIC_ENOTSUPP); 217 /* Other errors */ 218 if (src & IG4_ABRTSRC_ACKED_START) 219 return (IIC_EBUSERR); 220 } 221 /* 222 * TX_OVER, RX_OVER and RX_UNDER are caused by wrong RX/TX FIFO depth 223 * detection or driver's read/write pipelining errors. 224 */ 225 if (val & (IG4_INTR_TX_OVER | IG4_INTR_RX_OVER)) 226 return (IIC_EOVERFLOW); 227 if (val & IG4_INTR_RX_UNDER) 228 return (IIC_EUNDERFLOW); 229 230 return (IIC_NOERR); 231 } 232 233 /* 234 * Enable or disable the controller and wait for the controller to acknowledge 235 * the state change. 236 */ 237 static int 238 set_controller(ig4iic_softc_t *sc, uint32_t ctl) 239 { 240 int retry; 241 int error; 242 uint32_t v; 243 244 /* 245 * When the controller is enabled, interrupt on STOP detect 246 * or receive character ready and clear pending interrupts. 247 */ 248 ig4iic_set_intr_mask(sc, 0); 249 if (ctl & IG4_I2C_ENABLE) 250 reg_read(sc, IG4_REG_CLR_INTR); 251 252 reg_write(sc, IG4_REG_I2C_EN, ctl); 253 error = IIC_ETIMEOUT; 254 255 for (retry = 100; retry > 0; --retry) { 256 v = reg_read(sc, IG4_REG_ENABLE_STATUS); 257 if (((v ^ ctl) & IG4_I2C_ENABLE) == 0) { 258 error = 0; 259 break; 260 } 261 pause("i2cslv", 1); 262 } 263 return (error); 264 } 265 266 /* 267 * Wait up to 25ms for the requested interrupt using a 25uS polling loop. 268 */ 269 static int 270 wait_intr(ig4iic_softc_t *sc, uint32_t intr) 271 { 272 uint32_t v; 273 int error; 274 int txlvl = -1; 275 u_int count_us = 0; 276 u_int limit_us = 1000000; /* 1sec */ 277 278 for (;;) { 279 /* 280 * Check requested status 281 */ 282 v = reg_read(sc, IG4_REG_RAW_INTR_STAT); 283 error = intrstat2iic(sc, v & IG4_INTR_ERR_MASK); 284 if (error || (v & intr)) 285 break; 286 287 /* 288 * When waiting for the transmit FIFO to become empty, 289 * reset the timeout if we see a change in the transmit 290 * FIFO level as progress is being made. 291 */ 292 if (intr & (IG4_INTR_TX_EMPTY | IG4_INTR_STOP_DET)) { 293 v = reg_read(sc, IG4_REG_TXFLR) & IG4_FIFOLVL_MASK; 294 if (txlvl != v) { 295 txlvl = v; 296 count_us = 0; 297 } 298 } 299 300 /* 301 * Stop if we've run out of time. 302 */ 303 if (count_us >= limit_us) { 304 error = IIC_ETIMEOUT; 305 break; 306 } 307 308 /* 309 * When polling is not requested let the interrupt do its work. 310 */ 311 if (!DO_POLL(sc)) { 312 mtx_lock_spin(&sc->io_lock); 313 ig4iic_set_intr_mask(sc, intr | IG4_INTR_ERR_MASK); 314 msleep_spin(sc, &sc->io_lock, "i2cwait", 315 (hz + 99) / 100); /* sleep up to 10ms */ 316 ig4iic_set_intr_mask(sc, 0); 317 mtx_unlock_spin(&sc->io_lock); 318 count_us += 10000; 319 } else { 320 DELAY(25); 321 count_us += 25; 322 } 323 } 324 325 return (error); 326 } 327 328 /* 329 * Set the slave address. The controller must be disabled when 330 * changing the address. 331 * 332 * This operation does not issue anything to the I2C bus but sets 333 * the target address for when the controller later issues a START. 334 */ 335 static void 336 set_slave_addr(ig4iic_softc_t *sc, uint8_t slave) 337 { 338 uint32_t tar; 339 uint32_t ctl; 340 bool use_10bit; 341 342 use_10bit = false; 343 if (sc->slave_valid && sc->last_slave == slave && 344 sc->use_10bit == use_10bit) { 345 return; 346 } 347 sc->use_10bit = use_10bit; 348 349 /* 350 * Wait for TXFIFO to drain before disabling the controller. 351 */ 352 wait_intr(sc, IG4_INTR_TX_EMPTY); 353 354 set_controller(sc, 0); 355 ctl = reg_read(sc, IG4_REG_CTL); 356 ctl &= ~IG4_CTL_10BIT; 357 ctl |= IG4_CTL_RESTARTEN; 358 359 tar = slave; 360 if (sc->use_10bit) { 361 tar |= IG4_TAR_10BIT; 362 ctl |= IG4_CTL_10BIT; 363 } 364 reg_write(sc, IG4_REG_CTL, ctl); 365 reg_write(sc, IG4_REG_TAR_ADD, tar); 366 set_controller(sc, IG4_I2C_ENABLE); 367 sc->slave_valid = true; 368 sc->last_slave = slave; 369 } 370 371 /* 372 * IICBUS API FUNCTIONS 373 */ 374 static int 375 ig4iic_xfer_start(ig4iic_softc_t *sc, uint16_t slave, bool repeated_start) 376 { 377 set_slave_addr(sc, slave >> 1); 378 379 if (!repeated_start) { 380 /* 381 * Clear any previous TX/RX FIFOs overflow/underflow bits 382 * and I2C bus STOP condition. 383 */ 384 reg_read(sc, IG4_REG_CLR_INTR); 385 } 386 387 return (0); 388 } 389 390 static bool 391 ig4iic_xfer_is_started(ig4iic_softc_t *sc) 392 { 393 /* 394 * It requires that no IG4_REG_CLR_INTR or IG4_REG_CLR_START/STOP_DET 395 * register reads is issued after START condition. 396 */ 397 return ((reg_read(sc, IG4_REG_RAW_INTR_STAT) & 398 (IG4_INTR_START_DET | IG4_INTR_STOP_DET)) == IG4_INTR_START_DET); 399 } 400 401 static int 402 ig4iic_xfer_abort(ig4iic_softc_t *sc) 403 { 404 int error; 405 406 /* Request send of STOP condition and flush of TX FIFO */ 407 set_controller(sc, IG4_I2C_ABORT | IG4_I2C_ENABLE); 408 /* 409 * Wait for the TX_ABRT interrupt with ABRTSRC_TRANSFER 410 * bit set in TX_ABRT_SOURCE register. 411 */ 412 error = wait_intr(sc, IG4_INTR_STOP_DET); 413 set_controller(sc, IG4_I2C_ENABLE); 414 415 return (error == IIC_ESTATUS ? 0 : error); 416 } 417 418 /* 419 * Amount of unread data before next burst to get better I2C bus utilization. 420 * 2 bytes is enough in FAST mode. 8 bytes is better in FAST+ and HIGH modes. 421 * Intel-recommended value is 16 for DMA transfers with 64-byte depth FIFOs. 422 */ 423 #define IG4_FIFO_LOWAT 2 424 425 static int 426 ig4iic_read(ig4iic_softc_t *sc, uint8_t *buf, uint16_t len, 427 bool repeated_start, bool stop) 428 { 429 uint32_t cmd; 430 int requested = 0; 431 int received = 0; 432 int burst, target, lowat = 0; 433 int error; 434 435 if (len == 0) 436 return (0); 437 438 while (received < len) { 439 burst = sc->cfg.txfifo_depth - 440 (reg_read(sc, IG4_REG_TXFLR) & IG4_FIFOLVL_MASK); 441 if (burst <= 0) { 442 error = wait_intr(sc, IG4_INTR_TX_EMPTY); 443 if (error) 444 break; 445 burst = sc->cfg.txfifo_depth; 446 } 447 /* Ensure we have enough free space in RXFIFO */ 448 burst = MIN(burst, sc->cfg.rxfifo_depth - lowat); 449 target = MIN(requested + burst, (int)len); 450 while (requested < target) { 451 cmd = IG4_DATA_COMMAND_RD; 452 if (repeated_start && requested == 0) 453 cmd |= IG4_DATA_RESTART; 454 if (stop && requested == len - 1) 455 cmd |= IG4_DATA_STOP; 456 reg_write(sc, IG4_REG_DATA_CMD, cmd); 457 requested++; 458 } 459 /* Leave some data queued to maintain the hardware pipeline */ 460 lowat = 0; 461 if (requested != len && requested - received > IG4_FIFO_LOWAT) 462 lowat = IG4_FIFO_LOWAT; 463 /* After TXFLR fills up, clear it by reading available data */ 464 while (received < requested - lowat) { 465 burst = MIN((int)len - received, 466 reg_read(sc, IG4_REG_RXFLR) & IG4_FIFOLVL_MASK); 467 if (burst > 0) { 468 while (burst--) 469 buf[received++] = 0xFF & 470 reg_read(sc, IG4_REG_DATA_CMD); 471 } else { 472 error = wait_intr(sc, IG4_INTR_RX_FULL); 473 if (error) 474 goto out; 475 } 476 } 477 } 478 out: 479 return (error); 480 } 481 482 static int 483 ig4iic_write(ig4iic_softc_t *sc, uint8_t *buf, uint16_t len, 484 bool repeated_start, bool stop) 485 { 486 uint32_t cmd; 487 int sent = 0; 488 int burst, target; 489 int error; 490 bool lowat_set = false; 491 492 if (len == 0) 493 return (0); 494 495 while (sent < len) { 496 burst = sc->cfg.txfifo_depth - 497 (reg_read(sc, IG4_REG_TXFLR) & IG4_FIFOLVL_MASK); 498 target = MIN(sent + burst, (int)len); 499 /* Leave some data queued to maintain the hardware pipeline */ 500 if (!lowat_set && target != len) { 501 lowat_set = true; 502 reg_write(sc, IG4_REG_TX_TL, IG4_FIFO_LOWAT); 503 } 504 while(sent < target) { 505 cmd = buf[sent]; 506 if (repeated_start && sent == 0) 507 cmd |= IG4_DATA_RESTART; 508 if (stop && sent == len - 1) 509 cmd |= IG4_DATA_STOP; 510 reg_write(sc, IG4_REG_DATA_CMD, cmd); 511 sent++; 512 } 513 if (sent < len) { 514 error = wait_intr(sc, IG4_INTR_TX_EMPTY); 515 if (error) 516 break; 517 } 518 } 519 if (lowat_set) 520 reg_write(sc, IG4_REG_TX_TL, 0); 521 522 return (error); 523 } 524 525 int 526 ig4iic_transfer(device_t dev, struct iic_msg *msgs, uint32_t nmsgs) 527 { 528 ig4iic_softc_t *sc = device_get_softc(dev); 529 const char *reason = NULL; 530 uint32_t i; 531 int error; 532 int unit; 533 bool rpstart; 534 bool stop; 535 bool allocated; 536 537 /* 538 * The hardware interface imposes limits on allowed I2C messages. 539 * It is not possible to explicitly send a start or stop. 540 * They are automatically sent (or not sent, depending on the 541 * configuration) when a data byte is transferred. 542 * For this reason it's impossible to send a message with no data 543 * at all (like an SMBus quick message). 544 * The start condition is automatically generated after the stop 545 * condition, so it's impossible to not have a start after a stop. 546 * The repeated start condition is automatically sent if a change 547 * of the transfer direction happens, so it's impossible to have 548 * a change of direction without a (repeated) start. 549 * The repeated start can be forced even without the change of 550 * direction. 551 * Changing the target slave address requires resetting the hardware 552 * state, so it's impossible to do that without the stop followed 553 * by the start. 554 */ 555 for (i = 0; i < nmsgs; i++) { 556 #if 0 557 if (i == 0 && (msgs[i].flags & IIC_M_NOSTART) != 0) { 558 reason = "first message without start"; 559 break; 560 } 561 if (i == nmsgs - 1 && (msgs[i].flags & IIC_M_NOSTOP) != 0) { 562 reason = "last message without stop"; 563 break; 564 } 565 #endif 566 if (msgs[i].len == 0) { 567 reason = "message with no data"; 568 break; 569 } 570 if (i > 0) { 571 if ((msgs[i].flags & IIC_M_NOSTART) != 0 && 572 (msgs[i - 1].flags & IIC_M_NOSTOP) == 0) { 573 reason = "stop not followed by start"; 574 break; 575 } 576 if ((msgs[i - 1].flags & IIC_M_NOSTOP) != 0 && 577 msgs[i].slave != msgs[i - 1].slave) { 578 reason = "change of slave without stop"; 579 break; 580 } 581 if ((msgs[i].flags & IIC_M_NOSTART) != 0 && 582 (msgs[i].flags & IIC_M_RD) != 583 (msgs[i - 1].flags & IIC_M_RD)) { 584 reason = "change of direction without repeated" 585 " start"; 586 break; 587 } 588 } 589 } 590 if (reason != NULL) { 591 if (bootverbose) 592 device_printf(dev, "%s\n", reason); 593 return (IIC_ENOTSUPP); 594 } 595 596 /* Check if device is already allocated with iicbus_request_bus() */ 597 allocated = sx_xlocked(&sc->call_lock) != 0; 598 if (!allocated) 599 sx_xlock(&sc->call_lock); 600 601 /* Debugging - dump registers. */ 602 if (ig4_dump) { 603 unit = device_get_unit(dev); 604 if (ig4_dump & (1 << unit)) { 605 ig4_dump &= ~(1 << unit); 606 ig4iic_dump(sc); 607 } 608 } 609 610 /* 611 * Clear any previous abort condition that may have been holding 612 * the txfifo in reset. 613 */ 614 reg_read(sc, IG4_REG_CLR_TX_ABORT); 615 616 rpstart = false; 617 error = 0; 618 for (i = 0; i < nmsgs; i++) { 619 if ((msgs[i].flags & IIC_M_NOSTART) == 0) { 620 error = ig4iic_xfer_start(sc, msgs[i].slave, rpstart); 621 } else { 622 if (!sc->slave_valid || 623 (msgs[i].slave >> 1) != sc->last_slave) { 624 device_printf(dev, "start condition suppressed" 625 "but slave address is not set up"); 626 error = EINVAL; 627 break; 628 } 629 rpstart = false; 630 } 631 if (error != 0) 632 break; 633 634 stop = (msgs[i].flags & IIC_M_NOSTOP) == 0; 635 if (msgs[i].flags & IIC_M_RD) 636 error = ig4iic_read(sc, msgs[i].buf, msgs[i].len, 637 rpstart, stop); 638 else 639 error = ig4iic_write(sc, msgs[i].buf, msgs[i].len, 640 rpstart, stop); 641 642 /* Wait for error or stop condition occurred on the I2C bus */ 643 if (stop && error == 0) { 644 error = wait_intr(sc, IG4_INTR_STOP_DET); 645 if (error == 0) 646 reg_read(sc, IG4_REG_CLR_INTR); 647 } 648 649 if (error != 0) { 650 /* 651 * Send STOP condition if it's not done yet and flush 652 * both FIFOs. Do a controller soft reset if transfer 653 * abort is failed. 654 */ 655 if (ig4iic_xfer_is_started(sc) && 656 ig4iic_xfer_abort(sc) != 0) { 657 device_printf(sc->dev, "Failed to abort " 658 "transfer. Do the controller reset.\n"); 659 ig4iic_set_config(sc, true); 660 } else { 661 while (reg_read(sc, IG4_REG_I2C_STA) & 662 IG4_STATUS_RX_NOTEMPTY) 663 reg_read(sc, IG4_REG_DATA_CMD); 664 reg_read(sc, IG4_REG_TX_ABRT_SOURCE); 665 reg_read(sc, IG4_REG_CLR_INTR); 666 } 667 break; 668 } 669 670 rpstart = !stop; 671 } 672 673 if (!allocated) 674 sx_unlock(&sc->call_lock); 675 return (error); 676 } 677 678 int 679 ig4iic_reset(device_t dev, u_char speed, u_char addr, u_char *oldaddr) 680 { 681 ig4iic_softc_t *sc = device_get_softc(dev); 682 bool allocated; 683 684 allocated = sx_xlocked(&sc->call_lock) != 0; 685 if (!allocated) 686 sx_xlock(&sc->call_lock); 687 688 /* TODO handle speed configuration? */ 689 if (oldaddr != NULL) 690 *oldaddr = sc->last_slave << 1; 691 set_slave_addr(sc, addr >> 1); 692 if (addr == IIC_UNKNOWN) 693 sc->slave_valid = false; 694 695 if (!allocated) 696 sx_unlock(&sc->call_lock); 697 return (0); 698 } 699 700 int 701 ig4iic_callback(device_t dev, int index, caddr_t data) 702 { 703 ig4iic_softc_t *sc = device_get_softc(dev); 704 int error = 0; 705 int how; 706 707 switch (index) { 708 case IIC_REQUEST_BUS: 709 /* force polling if ig4iic is requested with IIC_DONTWAIT */ 710 how = *(int *)data; 711 if ((how & IIC_WAIT) == 0) { 712 if (sx_try_xlock(&sc->call_lock) == 0) 713 error = IIC_EBUSBSY; 714 else 715 sc->poll = true; 716 } else 717 sx_xlock(&sc->call_lock); 718 break; 719 720 case IIC_RELEASE_BUS: 721 sc->poll = false; 722 sx_unlock(&sc->call_lock); 723 break; 724 725 default: 726 error = errno2iic(EINVAL); 727 } 728 729 return (error); 730 } 731 732 /* 733 * Clock register values can be calculated with following rough equations: 734 * SCL_HCNT = ceil(IC clock rate * tHIGH) 735 * SCL_LCNT = ceil(IC clock rate * tLOW) 736 * SDA_HOLD = ceil(IC clock rate * SDA hold time) 737 * Precise equations take signal's falling, rising and spike suppression 738 * times in to account. They can be found in Synopsys or Intel documentation. 739 * 740 * Here we snarf formulas and defaults from Linux driver to be able to use 741 * timing values provided by Intel LPSS driver "as is". 742 */ 743 static int 744 ig4iic_clk_params(const struct ig4_hw *hw, int speed, 745 uint16_t *scl_hcnt, uint16_t *scl_lcnt, uint16_t *sda_hold) 746 { 747 uint32_t thigh, tlow, tf_max; /* nsec */ 748 uint32_t sda_fall_time; /* nsec */ 749 uint32_t scl_fall_time; /* nsec */ 750 751 switch (speed) { 752 case IG4_CTL_SPEED_STD: 753 thigh = IG4_SPEED_STD_THIGH; 754 tlow = IG4_SPEED_STD_TLOW; 755 tf_max = IG4_SPEED_STD_TF_MAX; 756 break; 757 758 case IG4_CTL_SPEED_FAST: 759 thigh = IG4_SPEED_FAST_THIGH; 760 tlow = IG4_SPEED_FAST_TLOW; 761 tf_max = IG4_SPEED_FAST_TF_MAX; 762 break; 763 764 default: 765 return (EINVAL); 766 } 767 768 /* Use slowest falling time defaults to be on the safe side */ 769 sda_fall_time = hw->sda_fall_time == 0 ? tf_max : hw->sda_fall_time; 770 *scl_hcnt = (uint16_t) 771 ((hw->ic_clock_rate * (thigh + sda_fall_time) + 500) / 1000 - 3); 772 773 scl_fall_time = hw->scl_fall_time == 0 ? tf_max : hw->scl_fall_time; 774 *scl_lcnt = (uint16_t) 775 ((hw->ic_clock_rate * (tlow + scl_fall_time) + 500) / 1000 - 1); 776 777 /* 778 * There is no "known good" default value for tHD;DAT so keep SDA_HOLD 779 * intact if sda_hold_time value is not provided. 780 */ 781 if (hw->sda_hold_time != 0) 782 *sda_hold = (uint16_t) 783 ((hw->ic_clock_rate * hw->sda_hold_time + 500) / 1000); 784 785 return (0); 786 } 787 788 #ifdef DEV_ACPI 789 static ACPI_STATUS 790 ig4iic_acpi_params(ACPI_HANDLE handle, char *method, 791 uint16_t *scl_hcnt, uint16_t *scl_lcnt, uint16_t *sda_hold) 792 { 793 ACPI_BUFFER buf; 794 ACPI_OBJECT *obj, *elems; 795 ACPI_STATUS status; 796 797 buf.Pointer = NULL; 798 buf.Length = ACPI_ALLOCATE_BUFFER; 799 800 status = AcpiEvaluateObject(handle, method, NULL, &buf); 801 if (ACPI_FAILURE(status)) 802 return (status); 803 804 status = AE_TYPE; 805 obj = (ACPI_OBJECT *)buf.Pointer; 806 if (obj->Type == ACPI_TYPE_PACKAGE && obj->Package.Count == 3) { 807 elems = obj->Package.Elements; 808 *scl_hcnt = elems[0].Integer.Value & IG4_SCL_CLOCK_MASK; 809 *scl_lcnt = elems[1].Integer.Value & IG4_SCL_CLOCK_MASK; 810 *sda_hold = elems[2].Integer.Value & IG4_SDA_TX_HOLD_MASK; 811 status = AE_OK; 812 } 813 814 AcpiOsFree(obj); 815 816 return (status); 817 } 818 #endif /* DEV_ACPI */ 819 820 static void 821 ig4iic_get_config(ig4iic_softc_t *sc) 822 { 823 const struct ig4_hw *hw; 824 uint32_t v; 825 #ifdef DEV_ACPI 826 ACPI_HANDLE handle; 827 #endif 828 /* Fetch default hardware config from controller */ 829 sc->cfg.version = reg_read(sc, IG4_REG_COMP_VER); 830 sc->cfg.bus_speed = reg_read(sc, IG4_REG_CTL) & IG4_CTL_SPEED_MASK; 831 sc->cfg.ss_scl_hcnt = 832 reg_read(sc, IG4_REG_SS_SCL_HCNT) & IG4_SCL_CLOCK_MASK; 833 sc->cfg.ss_scl_lcnt = 834 reg_read(sc, IG4_REG_SS_SCL_LCNT) & IG4_SCL_CLOCK_MASK; 835 sc->cfg.fs_scl_hcnt = 836 reg_read(sc, IG4_REG_FS_SCL_HCNT) & IG4_SCL_CLOCK_MASK; 837 sc->cfg.fs_scl_lcnt = 838 reg_read(sc, IG4_REG_FS_SCL_LCNT) & IG4_SCL_CLOCK_MASK; 839 sc->cfg.ss_sda_hold = sc->cfg.fs_sda_hold = 840 reg_read(sc, IG4_REG_SDA_HOLD) & IG4_SDA_TX_HOLD_MASK; 841 842 if (sc->cfg.bus_speed != IG4_CTL_SPEED_STD) 843 sc->cfg.bus_speed = IG4_CTL_SPEED_FAST; 844 845 /* REG_COMP_PARAM1 is not documented in latest Intel specs */ 846 if (sc->version == IG4_HASWELL || sc->version == IG4_ATOM) { 847 v = reg_read(sc, IG4_REG_COMP_PARAM1); 848 if (IG4_PARAM1_TXFIFO_DEPTH(v) != 0) 849 sc->cfg.txfifo_depth = IG4_PARAM1_TXFIFO_DEPTH(v); 850 if (IG4_PARAM1_RXFIFO_DEPTH(v) != 0) 851 sc->cfg.rxfifo_depth = IG4_PARAM1_RXFIFO_DEPTH(v); 852 } else { 853 /* 854 * Hardware does not allow FIFO Threshold Levels value to be 855 * set larger than the depth of the buffer. If an attempt is 856 * made to do that, the actual value set will be the maximum 857 * depth of the buffer. 858 */ 859 v = reg_read(sc, IG4_REG_TX_TL); 860 reg_write(sc, IG4_REG_TX_TL, v | IG4_FIFO_MASK); 861 sc->cfg.txfifo_depth = 862 (reg_read(sc, IG4_REG_TX_TL) & IG4_FIFO_MASK) + 1; 863 reg_write(sc, IG4_REG_TX_TL, v); 864 v = reg_read(sc, IG4_REG_RX_TL); 865 reg_write(sc, IG4_REG_RX_TL, v | IG4_FIFO_MASK); 866 sc->cfg.rxfifo_depth = 867 (reg_read(sc, IG4_REG_RX_TL) & IG4_FIFO_MASK) + 1; 868 reg_write(sc, IG4_REG_RX_TL, v); 869 } 870 871 /* Override hardware config with IC_clock-based counter values */ 872 if (ig4_timings < 2 && sc->version < nitems(ig4iic_hw)) { 873 hw = &ig4iic_hw[sc->version]; 874 sc->cfg.bus_speed = IG4_CTL_SPEED_FAST; 875 ig4iic_clk_params(hw, IG4_CTL_SPEED_STD, &sc->cfg.ss_scl_hcnt, 876 &sc->cfg.ss_scl_lcnt, &sc->cfg.ss_sda_hold); 877 ig4iic_clk_params(hw, IG4_CTL_SPEED_FAST, &sc->cfg.fs_scl_hcnt, 878 &sc->cfg.fs_scl_lcnt, &sc->cfg.fs_sda_hold); 879 if (hw->txfifo_depth != 0) 880 sc->cfg.txfifo_depth = hw->txfifo_depth; 881 if (hw->rxfifo_depth != 0) 882 sc->cfg.rxfifo_depth = hw->rxfifo_depth; 883 } else if (ig4_timings == 2) { 884 /* 885 * Timings of original ig4 driver: 886 * Program based on a 25000 Hz clock. This is a bit of a 887 * hack (obviously). The defaults are 400 and 470 for standard 888 * and 60 and 130 for fast. The defaults for standard fail 889 * utterly (presumably cause an abort) because the clock time 890 * is ~18.8ms by default. This brings it down to ~4ms. 891 */ 892 sc->cfg.bus_speed = IG4_CTL_SPEED_STD; 893 sc->cfg.ss_scl_hcnt = sc->cfg.fs_scl_hcnt = 100; 894 sc->cfg.ss_scl_lcnt = sc->cfg.fs_scl_lcnt = 125; 895 if (sc->version == IG4_SKYLAKE) 896 sc->cfg.ss_sda_hold = sc->cfg.fs_sda_hold = 28; 897 } 898 899 #ifdef DEV_ACPI 900 /* Evaluate SSCN and FMCN ACPI methods to fetch timings */ 901 if (ig4_timings == 0 && (handle = acpi_get_handle(sc->dev)) != NULL) { 902 ig4iic_acpi_params(handle, "SSCN", &sc->cfg.ss_scl_hcnt, 903 &sc->cfg.ss_scl_lcnt, &sc->cfg.ss_sda_hold); 904 ig4iic_acpi_params(handle, "FMCN", &sc->cfg.fs_scl_hcnt, 905 &sc->cfg.fs_scl_lcnt, &sc->cfg.fs_sda_hold); 906 } 907 #endif 908 909 if (bootverbose) { 910 device_printf(sc->dev, "Controller parameters:\n"); 911 printf(" Speed: %s\n", 912 sc->cfg.bus_speed == IG4_CTL_SPEED_STD ? "Std" : "Fast"); 913 printf(" Regs: HCNT :LCNT :SDAHLD\n"); 914 printf(" Std: 0x%04hx:0x%04hx:0x%04hx\n", 915 sc->cfg.ss_scl_hcnt, sc->cfg.ss_scl_lcnt, 916 sc->cfg.ss_sda_hold); 917 printf(" Fast: 0x%04hx:0x%04hx:0x%04hx\n", 918 sc->cfg.fs_scl_hcnt, sc->cfg.fs_scl_lcnt, 919 sc->cfg.fs_sda_hold); 920 printf(" FIFO: RX:0x%04x: TX:0x%04x\n", 921 sc->cfg.rxfifo_depth, sc->cfg.txfifo_depth); 922 } 923 } 924 925 static int 926 ig4iic_set_config(ig4iic_softc_t *sc, bool reset) 927 { 928 uint32_t v; 929 930 v = reg_read(sc, IG4_REG_DEVIDLE_CTRL); 931 if (IG4_HAS_ADDREGS(sc->version) && (v & IG4_RESTORE_REQUIRED)) { 932 reg_write(sc, IG4_REG_DEVIDLE_CTRL, IG4_DEVICE_IDLE | IG4_RESTORE_REQUIRED); 933 reg_write(sc, IG4_REG_DEVIDLE_CTRL, 0); 934 pause("i2crst", 1); 935 reset = true; 936 } 937 938 if ((sc->version == IG4_HASWELL || sc->version == IG4_ATOM) && reset) { 939 reg_write(sc, IG4_REG_RESETS_HSW, IG4_RESETS_ASSERT_HSW); 940 reg_write(sc, IG4_REG_RESETS_HSW, IG4_RESETS_DEASSERT_HSW); 941 } else if (IG4_HAS_ADDREGS(sc->version) && reset) { 942 reg_write(sc, IG4_REG_RESETS_SKL, IG4_RESETS_ASSERT_SKL); 943 reg_write(sc, IG4_REG_RESETS_SKL, IG4_RESETS_DEASSERT_SKL); 944 } 945 946 if (sc->version == IG4_ATOM) 947 v = reg_read(sc, IG4_REG_COMP_TYPE); 948 949 if (sc->version == IG4_HASWELL || sc->version == IG4_ATOM) { 950 v = reg_read(sc, IG4_REG_COMP_PARAM1); 951 v = reg_read(sc, IG4_REG_GENERAL); 952 /* 953 * The content of IG4_REG_GENERAL is different for each 954 * controller version. 955 */ 956 if (sc->version == IG4_HASWELL && 957 (v & IG4_GENERAL_SWMODE) == 0) { 958 v |= IG4_GENERAL_SWMODE; 959 reg_write(sc, IG4_REG_GENERAL, v); 960 v = reg_read(sc, IG4_REG_GENERAL); 961 } 962 } 963 964 if (sc->version == IG4_HASWELL) { 965 v = reg_read(sc, IG4_REG_SW_LTR_VALUE); 966 v = reg_read(sc, IG4_REG_AUTO_LTR_VALUE); 967 } else if (IG4_HAS_ADDREGS(sc->version)) { 968 v = reg_read(sc, IG4_REG_ACTIVE_LTR_VALUE); 969 v = reg_read(sc, IG4_REG_IDLE_LTR_VALUE); 970 } 971 972 if (sc->version == IG4_HASWELL || sc->version == IG4_ATOM) { 973 v = reg_read(sc, IG4_REG_COMP_VER); 974 if (v < IG4_COMP_MIN_VER) 975 return(ENXIO); 976 } 977 978 if (set_controller(sc, 0)) { 979 device_printf(sc->dev, "controller error during attach-1\n"); 980 return (ENXIO); 981 } 982 983 reg_read(sc, IG4_REG_CLR_INTR); 984 reg_write(sc, IG4_REG_INTR_MASK, 0); 985 sc->intr_mask = 0; 986 987 reg_write(sc, IG4_REG_SS_SCL_HCNT, sc->cfg.ss_scl_hcnt); 988 reg_write(sc, IG4_REG_SS_SCL_LCNT, sc->cfg.ss_scl_lcnt); 989 reg_write(sc, IG4_REG_FS_SCL_HCNT, sc->cfg.fs_scl_hcnt); 990 reg_write(sc, IG4_REG_FS_SCL_LCNT, sc->cfg.fs_scl_lcnt); 991 reg_write(sc, IG4_REG_SDA_HOLD, 992 (sc->cfg.bus_speed & IG4_CTL_SPEED_MASK) == IG4_CTL_SPEED_STD ? 993 sc->cfg.ss_sda_hold : sc->cfg.fs_sda_hold); 994 995 /* 996 * Use a threshold of 1 so we get interrupted on each character, 997 * allowing us to use mtx_sleep() in our poll code. Not perfect 998 * but this is better than using DELAY() for receiving data. 999 * 1000 * See ig4_var.h for details on interrupt handler synchronization. 1001 */ 1002 reg_write(sc, IG4_REG_RX_TL, 0); 1003 reg_write(sc, IG4_REG_TX_TL, 0); 1004 1005 reg_write(sc, IG4_REG_CTL, 1006 IG4_CTL_MASTER | 1007 IG4_CTL_SLAVE_DISABLE | 1008 IG4_CTL_RESTARTEN | 1009 (sc->cfg.bus_speed & IG4_CTL_SPEED_MASK)); 1010 1011 /* Force setting of the target address on the next transfer */ 1012 sc->slave_valid = false; 1013 1014 return (0); 1015 } 1016 1017 /* 1018 * Called from ig4iic_pci_attach/detach() 1019 */ 1020 int 1021 ig4iic_attach(ig4iic_softc_t *sc) 1022 { 1023 int error; 1024 1025 mtx_init(&sc->io_lock, "IG4 I/O lock", NULL, MTX_SPIN); 1026 sx_init(&sc->call_lock, "IG4 call lock"); 1027 1028 ig4iic_get_config(sc); 1029 1030 error = ig4iic_set_config(sc, IG4_HAS_ADDREGS(sc->version)); 1031 if (error) 1032 goto done; 1033 1034 sc->iicbus = device_add_child(sc->dev, "iicbus", -1); 1035 if (sc->iicbus == NULL) { 1036 device_printf(sc->dev, "iicbus driver not found\n"); 1037 error = ENXIO; 1038 goto done; 1039 } 1040 1041 if (set_controller(sc, IG4_I2C_ENABLE)) { 1042 device_printf(sc->dev, "controller error during attach-2\n"); 1043 error = ENXIO; 1044 goto done; 1045 } 1046 if (set_controller(sc, 0)) { 1047 device_printf(sc->dev, "controller error during attach-3\n"); 1048 error = ENXIO; 1049 goto done; 1050 } 1051 error = bus_setup_intr(sc->dev, sc->intr_res, INTR_TYPE_MISC | INTR_MPSAFE, 1052 ig4iic_intr, NULL, sc, &sc->intr_handle); 1053 if (error) { 1054 device_printf(sc->dev, 1055 "Unable to setup irq: error %d\n", error); 1056 } 1057 1058 error = bus_generic_attach(sc->dev); 1059 if (error) { 1060 device_printf(sc->dev, 1061 "failed to attach child: error %d\n", error); 1062 } 1063 1064 done: 1065 return (error); 1066 } 1067 1068 int 1069 ig4iic_detach(ig4iic_softc_t *sc) 1070 { 1071 int error; 1072 1073 if (device_is_attached(sc->dev)) { 1074 error = bus_generic_detach(sc->dev); 1075 if (error) 1076 return (error); 1077 } 1078 if (sc->iicbus) 1079 device_delete_child(sc->dev, sc->iicbus); 1080 if (sc->intr_handle) 1081 bus_teardown_intr(sc->dev, sc->intr_res, sc->intr_handle); 1082 1083 sx_xlock(&sc->call_lock); 1084 1085 sc->iicbus = NULL; 1086 sc->intr_handle = NULL; 1087 reg_write(sc, IG4_REG_INTR_MASK, 0); 1088 set_controller(sc, 0); 1089 1090 sx_xunlock(&sc->call_lock); 1091 1092 mtx_destroy(&sc->io_lock); 1093 sx_destroy(&sc->call_lock); 1094 1095 return (0); 1096 } 1097 1098 int 1099 ig4iic_suspend(ig4iic_softc_t *sc) 1100 { 1101 int error; 1102 1103 /* suspend all children */ 1104 error = bus_generic_suspend(sc->dev); 1105 1106 sx_xlock(&sc->call_lock); 1107 set_controller(sc, 0); 1108 if (IG4_HAS_ADDREGS(sc->version)) { 1109 /* 1110 * Place the device in the idle state, just to be safe 1111 */ 1112 reg_write(sc, IG4_REG_DEVIDLE_CTRL, IG4_DEVICE_IDLE); 1113 /* 1114 * Controller can become dysfunctional if I2C lines are pulled 1115 * down when suspend procedure turns off power to I2C device. 1116 * Place device in the reset state to avoid this. 1117 */ 1118 reg_write(sc, IG4_REG_RESETS_SKL, IG4_RESETS_ASSERT_SKL); 1119 } 1120 sx_xunlock(&sc->call_lock); 1121 1122 return (error); 1123 } 1124 1125 int ig4iic_resume(ig4iic_softc_t *sc) 1126 { 1127 int error; 1128 1129 sx_xlock(&sc->call_lock); 1130 if (ig4iic_set_config(sc, IG4_HAS_ADDREGS(sc->version))) 1131 device_printf(sc->dev, "controller error during resume\n"); 1132 sx_xunlock(&sc->call_lock); 1133 1134 error = bus_generic_resume(sc->dev); 1135 1136 return (error); 1137 } 1138 1139 /* 1140 * Interrupt Operation, see ig4_var.h for locking semantics. 1141 */ 1142 static int 1143 ig4iic_intr(void *cookie) 1144 { 1145 ig4iic_softc_t *sc = cookie; 1146 int retval = FILTER_STRAY; 1147 1148 mtx_lock_spin(&sc->io_lock); 1149 /* Ignore stray interrupts */ 1150 if (sc->intr_mask != 0 && reg_read(sc, IG4_REG_INTR_STAT) != 0) { 1151 /* Interrupt bits are cleared in wait_intr() loop */ 1152 ig4iic_set_intr_mask(sc, 0); 1153 wakeup(sc); 1154 retval = FILTER_HANDLED; 1155 } 1156 mtx_unlock_spin(&sc->io_lock); 1157 1158 return (retval); 1159 } 1160 1161 #define REGDUMP(sc, reg) \ 1162 device_printf(sc->dev, " %-23s %08x\n", #reg, reg_read(sc, reg)) 1163 1164 static void 1165 ig4iic_dump(ig4iic_softc_t *sc) 1166 { 1167 device_printf(sc->dev, "ig4iic register dump:\n"); 1168 REGDUMP(sc, IG4_REG_CTL); 1169 REGDUMP(sc, IG4_REG_TAR_ADD); 1170 REGDUMP(sc, IG4_REG_SS_SCL_HCNT); 1171 REGDUMP(sc, IG4_REG_SS_SCL_LCNT); 1172 REGDUMP(sc, IG4_REG_FS_SCL_HCNT); 1173 REGDUMP(sc, IG4_REG_FS_SCL_LCNT); 1174 REGDUMP(sc, IG4_REG_INTR_STAT); 1175 REGDUMP(sc, IG4_REG_INTR_MASK); 1176 REGDUMP(sc, IG4_REG_RAW_INTR_STAT); 1177 REGDUMP(sc, IG4_REG_RX_TL); 1178 REGDUMP(sc, IG4_REG_TX_TL); 1179 REGDUMP(sc, IG4_REG_I2C_EN); 1180 REGDUMP(sc, IG4_REG_I2C_STA); 1181 REGDUMP(sc, IG4_REG_TXFLR); 1182 REGDUMP(sc, IG4_REG_RXFLR); 1183 REGDUMP(sc, IG4_REG_SDA_HOLD); 1184 REGDUMP(sc, IG4_REG_TX_ABRT_SOURCE); 1185 REGDUMP(sc, IG4_REG_SLV_DATA_NACK); 1186 REGDUMP(sc, IG4_REG_DMA_CTRL); 1187 REGDUMP(sc, IG4_REG_DMA_TDLR); 1188 REGDUMP(sc, IG4_REG_DMA_RDLR); 1189 REGDUMP(sc, IG4_REG_SDA_SETUP); 1190 REGDUMP(sc, IG4_REG_ENABLE_STATUS); 1191 REGDUMP(sc, IG4_REG_COMP_PARAM1); 1192 REGDUMP(sc, IG4_REG_COMP_VER); 1193 if (sc->version == IG4_ATOM) { 1194 REGDUMP(sc, IG4_REG_COMP_TYPE); 1195 REGDUMP(sc, IG4_REG_CLK_PARMS); 1196 } 1197 if (sc->version == IG4_HASWELL || sc->version == IG4_ATOM) { 1198 REGDUMP(sc, IG4_REG_RESETS_HSW); 1199 REGDUMP(sc, IG4_REG_GENERAL); 1200 } else if (sc->version == IG4_SKYLAKE) { 1201 REGDUMP(sc, IG4_REG_RESETS_SKL); 1202 } 1203 if (sc->version == IG4_HASWELL) { 1204 REGDUMP(sc, IG4_REG_SW_LTR_VALUE); 1205 REGDUMP(sc, IG4_REG_AUTO_LTR_VALUE); 1206 } else if (IG4_HAS_ADDREGS(sc->version)) { 1207 REGDUMP(sc, IG4_REG_ACTIVE_LTR_VALUE); 1208 REGDUMP(sc, IG4_REG_IDLE_LTR_VALUE); 1209 } 1210 } 1211 #undef REGDUMP 1212 1213 DRIVER_MODULE(iicbus, ig4iic, iicbus_driver, NULL, NULL); 1214 #ifdef DEV_ACPI 1215 DRIVER_MODULE(acpi_iicbus, ig4iic, acpi_iicbus_driver, NULL, NULL); 1216 #endif 1217 MODULE_DEPEND(ig4iic, iicbus, IICBUS_MINVER, IICBUS_PREFVER, IICBUS_MAXVER); 1218 MODULE_VERSION(ig4iic, 1); 1219