1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2/* 3 * Copyright (C) 2019 Marvell International Ltd. 4 * 5 * Device tree for the CN9130-DB board. 6 */ 7 8#include "cn9130.dtsi" 9 10#include <dt-bindings/gpio/gpio.h> 11 12/ { 13 chosen { 14 stdout-path = "serial0:115200n8"; 15 }; 16 17 aliases { 18 gpio1 = &cp0_gpio1; 19 gpio2 = &cp0_gpio2; 20 i2c0 = &cp0_i2c0; 21 ethernet0 = &cp0_eth0; 22 ethernet1 = &cp0_eth1; 23 ethernet2 = &cp0_eth2; 24 spi1 = &cp0_spi0; 25 spi2 = &cp0_spi1; 26 }; 27 28 memory@0 { 29 device_type = "memory"; 30 reg = <0x0 0x0 0x0 0x80000000>; 31 }; 32 33 ap0_reg_sd_vccq: ap0_sd_vccq@0 { 34 compatible = "regulator-gpio"; 35 regulator-name = "ap0_sd_vccq"; 36 regulator-min-microvolt = <1800000>; 37 regulator-max-microvolt = <3300000>; 38 gpios = <&expander0 8 GPIO_ACTIVE_HIGH>; 39 states = <1800000 0x1 3300000 0x0>; 40 }; 41 42 cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 { 43 compatible = "regulator-fixed"; 44 regulator-name = "cp0-xhci0-vbus"; 45 regulator-min-microvolt = <5000000>; 46 regulator-max-microvolt = <5000000>; 47 enable-active-high; 48 gpio = <&expander0 0 GPIO_ACTIVE_HIGH>; 49 }; 50 51 cp0_usb3_0_phy0: cp0_usb3_phy@0 { 52 compatible = "usb-nop-xceiv"; 53 vcc-supply = <&cp0_reg_usb3_vbus0>; 54 }; 55 56 cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 { 57 compatible = "regulator-fixed"; 58 regulator-name = "cp0-xhci1-vbus"; 59 regulator-min-microvolt = <5000000>; 60 regulator-max-microvolt = <5000000>; 61 enable-active-high; 62 gpio = <&expander0 1 GPIO_ACTIVE_HIGH>; 63 }; 64 65 cp0_usb3_0_phy1: cp0_usb3_phy@1 { 66 compatible = "usb-nop-xceiv"; 67 vcc-supply = <&cp0_reg_usb3_vbus1>; 68 }; 69 70 cp0_reg_sd_vccq: cp0_sd_vccq@0 { 71 compatible = "regulator-gpio"; 72 regulator-name = "cp0_sd_vccq"; 73 regulator-min-microvolt = <1800000>; 74 regulator-max-microvolt = <3300000>; 75 gpios = <&expander0 15 GPIO_ACTIVE_HIGH>; 76 states = <1800000 0x1 77 3300000 0x0>; 78 }; 79 80 cp0_reg_sd_vcc: cp0_sd_vcc@0 { 81 compatible = "regulator-fixed"; 82 regulator-name = "cp0_sd_vcc"; 83 regulator-min-microvolt = <3300000>; 84 regulator-max-microvolt = <3300000>; 85 gpio = <&expander0 14 GPIO_ACTIVE_HIGH>; 86 enable-active-high; 87 regulator-always-on; 88 }; 89 90 cp0_sfp_eth0: sfp-eth@0 { 91 compatible = "sff,sfp"; 92 i2c-bus = <&cp0_sfpp0_i2c>; 93 los-gpios = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>; 94 mod-def0-gpios = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>; 95 tx-disable-gpios = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>; 96 tx-fault-gpios = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>; 97 /* 98 * SFP cages are unconnected on early PCBs because of an the I2C 99 * lanes not being connected. Prevent the port for being 100 * unusable by disabling the SFP node. 101 */ 102 status = "disabled"; 103 }; 104}; 105 106&uart0 { 107 status = "okay"; 108}; 109 110/* on-board eMMC - U9 */ 111&ap_sdhci0 { 112 pinctrl-names = "default"; 113 bus-width = <8>; 114 vqmmc-supply = <&ap0_reg_sd_vccq>; 115 status = "okay"; 116}; 117 118&cp0_crypto { 119 status = "disabled"; 120}; 121 122&cp0_ethernet { 123 status = "okay"; 124}; 125 126/* SLM-1521-V2, CON9 */ 127&cp0_eth0 { 128 status = "okay"; 129 phy-mode = "10gbase-r"; 130 /* Generic PHY, providing serdes lanes */ 131 phys = <&cp0_comphy4 0>; 132 managed = "in-band-status"; 133 sfp = <&cp0_sfp_eth0>; 134}; 135 136/* CON56 */ 137&cp0_eth1 { 138 status = "okay"; 139 phy = <&phy0>; 140 phy-mode = "rgmii-id"; 141}; 142 143/* CON57 */ 144&cp0_eth2 { 145 status = "okay"; 146 phy = <&phy1>; 147 phy-mode = "rgmii-id"; 148}; 149 150&cp0_gpio1 { 151 status = "okay"; 152}; 153 154&cp0_gpio2 { 155 status = "okay"; 156}; 157 158&cp0_i2c0 { 159 status = "okay"; 160 pinctrl-names = "default"; 161 pinctrl-0 = <&cp0_i2c0_pins>; 162 clock-frequency = <100000>; 163 164 /* U36 */ 165 expander0: pca953x@21 { 166 compatible = "nxp,pca9555"; 167 pinctrl-names = "default"; 168 gpio-controller; 169 #gpio-cells = <2>; 170 reg = <0x21>; 171 status = "okay"; 172 }; 173 174 /* U42 */ 175 eeprom0: eeprom@50 { 176 compatible = "atmel,24c64"; 177 reg = <0x50>; 178 pagesize = <0x20>; 179 }; 180 181 /* U38 */ 182 eeprom1: eeprom@57 { 183 compatible = "atmel,24c64"; 184 reg = <0x57>; 185 pagesize = <0x20>; 186 }; 187}; 188 189&cp0_i2c1 { 190 status = "okay"; 191 clock-frequency = <100000>; 192 193 /* SLM-1521-V2 - U3 */ 194 i2c-mux@72 { /* verify address - depends on dpr */ 195 compatible = "nxp,pca9544"; 196 #address-cells = <1>; 197 #size-cells = <0>; 198 reg = <0x72>; 199 cp0_sfpp0_i2c: i2c@0 { 200 #address-cells = <1>; 201 #size-cells = <0>; 202 reg = <0>; 203 }; 204 205 i2c@1 { 206 #address-cells = <1>; 207 #size-cells = <0>; 208 reg = <1>; 209 /* U12 */ 210 cp0_module_expander1: pca9555@21 { 211 compatible = "nxp,pca9555"; 212 pinctrl-names = "default"; 213 gpio-controller; 214 #gpio-cells = <2>; 215 reg = <0x21>; 216 }; 217 218 }; 219 }; 220}; 221 222&cp0_mdio { 223 status = "okay"; 224 225 phy0: ethernet-phy@0 { 226 reg = <0>; 227 }; 228 229 phy1: ethernet-phy@1 { 230 reg = <1>; 231 }; 232}; 233 234/* U54 */ 235&cp0_nand_controller { 236 status = "disabled"; 237 pinctrl-names = "default"; 238 pinctrl-0 = <&nand_pins &nand_rb>; 239 240 nand@0 { 241 reg = <0>; 242 label = "main-storage"; 243 nand-rb = <0>; 244 nand-ecc-mode = "hw"; 245 nand-on-flash-bbt; 246 nand-ecc-strength = <8>; 247 nand-ecc-step-size = <512>; 248 249 partitions { 250 compatible = "fixed-partitions"; 251 #address-cells = <1>; 252 #size-cells = <1>; 253 254 partition@0 { 255 label = "U-Boot"; 256 reg = <0 0x200000>; 257 }; 258 partition@200000 { 259 label = "Linux"; 260 reg = <0x200000 0xe00000>; 261 }; 262 partition@1000000 { 263 label = "Filesystem"; 264 reg = <0x1000000 0x3f000000>; 265 }; 266 }; 267 }; 268}; 269 270/* SLM-1521-V2, CON6 */ 271&cp0_pcie0 { 272 status = "okay"; 273 num-lanes = <4>; 274 num-viewport = <8>; 275 /* Generic PHY, providing serdes lanes */ 276 phys = <&cp0_comphy0 0 277 &cp0_comphy1 0 278 &cp0_comphy2 0 279 &cp0_comphy3 0>; 280}; 281 282&cp0_sata0 { 283 status = "okay"; 284 285 /* SLM-1521-V2, CON2 */ 286 sata-port@1 { 287 status = "okay"; 288 /* Generic PHY, providing serdes lanes */ 289 phys = <&cp0_comphy5 1>; 290 }; 291}; 292 293/* CON 28 */ 294&cp0_sdhci0 { 295 status = "okay"; 296 pinctrl-names = "default"; 297 pinctrl-0 = <&cp0_sdhci_pins 298 &cp0_sdhci_cd_pins>; 299 bus-width = <4>; 300 cd-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>; 301 no-1-8-v; 302 vqmmc-supply = <&cp0_reg_sd_vccq>; 303 vmmc-supply = <&cp0_reg_sd_vcc>; 304}; 305 306/* U55 */ 307&cp0_spi1 { 308 status = "disabled"; 309 pinctrl-names = "default"; 310 pinctrl-0 = <&cp0_spi1_pins>; 311 reg = <0x700680 0x50>; 312 313 flash@0 { 314 #address-cells = <0x1>; 315 #size-cells = <0x1>; 316 compatible = "jedec,spi-nor"; 317 reg = <0x0>; 318 /* On-board MUX does not allow higher frequencies */ 319 spi-max-frequency = <40000000>; 320 321 partitions { 322 compatible = "fixed-partitions"; 323 #address-cells = <1>; 324 #size-cells = <1>; 325 326 partition@0 { 327 label = "U-Boot-0"; 328 reg = <0x0 0x200000>; 329 }; 330 331 partition@400000 { 332 label = "Filesystem-0"; 333 reg = <0x200000 0xe00000>; 334 }; 335 }; 336 }; 337}; 338 339&cp0_syscon0 { 340 cp0_pinctrl: pinctrl { 341 compatible = "marvell,cp115-standalone-pinctrl"; 342 343 cp0_i2c0_pins: cp0-i2c-pins-0 { 344 marvell,pins = "mpp37", "mpp38"; 345 marvell,function = "i2c0"; 346 }; 347 cp0_i2c1_pins: cp0-i2c-pins-1 { 348 marvell,pins = "mpp35", "mpp36"; 349 marvell,function = "i2c1"; 350 }; 351 cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 { 352 marvell,pins = "mpp0", "mpp1", "mpp2", 353 "mpp3", "mpp4", "mpp5", 354 "mpp6", "mpp7", "mpp8", 355 "mpp9", "mpp10", "mpp11"; 356 marvell,function = "ge0"; 357 }; 358 cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 { 359 marvell,pins = "mpp44", "mpp45", "mpp46", 360 "mpp47", "mpp48", "mpp49", 361 "mpp50", "mpp51", "mpp52", 362 "mpp53", "mpp54", "mpp55"; 363 marvell,function = "ge1"; 364 }; 365 cp0_sdhci_cd_pins: cp0-sdhci-cd-pins-0 { 366 marvell,pins = "mpp43"; 367 marvell,function = "gpio"; 368 }; 369 cp0_sdhci_pins: cp0-sdhi-pins-0 { 370 marvell,pins = "mpp56", "mpp57", "mpp58", 371 "mpp59", "mpp60", "mpp61"; 372 marvell,function = "sdio"; 373 }; 374 cp0_spi1_pins: cp0-spi-pins-1 { 375 marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; 376 marvell,function = "spi1"; 377 }; 378 nand_pins: nand-pins { 379 marvell,pins = "mpp15", "mpp16", "mpp17", "mpp18", 380 "mpp19", "mpp20", "mpp21", "mpp22", 381 "mpp23", "mpp24", "mpp25", "mpp26", 382 "mpp27"; 383 marvell,function = "dev"; 384 }; 385 nand_rb: nand-rb { 386 marvell,pins = "mpp13"; 387 marvell,function = "nf"; 388 }; 389 }; 390}; 391 392&cp0_utmi { 393 status = "okay"; 394}; 395 396&cp0_usb3_0 { 397 status = "okay"; 398 usb-phy = <&cp0_usb3_0_phy0>; 399 phys = <&cp0_utmi0>; 400 phy-names = "utmi"; 401 dr_mode = "host"; 402}; 403 404&cp0_usb3_1 { 405 status = "okay"; 406 usb-phy = <&cp0_usb3_0_phy1>; 407 phys = <&cp0_utmi1>; 408 phy-names = "utmi"; 409 dr_mode = "host"; 410}; 411