| /linux/drivers/gpu/drm/nouveau/nvkm/subdev/iccsense/ |
| H A D | base.c | 117 list_for_each_entry(rail, &iccsense->rails, head) { in nvkm_iccsense_read_all()
141 list_for_each_entry_safe(rail, tmpr, &iccsense->rails, head) { in nvkm_iccsense_dtor()
291 list_add_tail(&rail->head, &iccsense->rails); in nvkm_iccsense_oneinit()
328 INIT_LIST_HEAD(&(*iccsense)->rails); in nvkm_iccsense_new_()
|
| /linux/drivers/gpu/drm/nouveau/include/nvkm/subdev/ |
| H A D | iccsense.h | 11 struct list_head rails; member
|
| /linux/arch/arm64/boot/dts/qcom/ |
| H A D | sa8155p.dtsi | 6 * Most notably, the RPMhPD setup differs: MMCX and LCX/LMX rails are gone,
|
| H A D | sc7180-trogdor-homestar.dtsi | 98 * rail and eDP rails are separate from each other on homestar (but
|
| /linux/arch/arm64/boot/dts/rockchip/ |
| H A D | rk3588-jaguar-pre-ict-tester.dtso | 12 * This adapter routes some GPIOs to power rails and loops together some other
75 * GPIO3_A3 requires two power rails to be properly
97 * GPIO3_B2 requires two power rails to be properly
|
| H A D | rk3399-gru.dtsi | 24 * In general an attempt is made to include all rails called out by
25 * the schematic as long as those rails interact in some way with
29 * - Rails _are_ included if the rails go to the AP even if the AP
34 * If two rails are substantially the same from the AP's point of
36 * put the child rail as an alias of the parent rail. Sometimes rails
40 * - The rails are actually connected to each other by a jumper and
|
| /linux/Documentation/hwmon/ |
| H A D | ucd9200.rst | 108 rails. See chip datasheets for details.
114 created for enabled rails. See chip datasheets for
|
| H A D | mp2856.rst | 31 setting of different formats on rails 1 and 2. For VID the following
|
| H A D | lochnagar.rst | 14 rails provided to the minicards. The Current Monitor does not require any
|
| H A D | mp2975.rst | 31 setting of different formats on rails 1 and 2. For VID the following
|
| H A D | ucd9000.rst | 31 sequences up to 12 independent voltage rails. The device integrates a 12-bit
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-driver-bd9571mwv-regulator | 6 if DDR power rails will be kept powered during system suspend.
|
| /linux/Documentation/devicetree/bindings/mfd/ |
| H A D | max77620.txt | 122 GPIO1/nRST_IO pins are HIGH only if all rails
124 If any of the rails goes down(which are enabled for POK
|
| H A D | as3722.txt | 127 AS3722 supports the system power off by turning off all its rails.
|
| /linux/drivers/acpi/pmic/ |
| H A D | Kconfig | 8 to control power rails and sensor reading/writing on the
|
| /linux/Documentation/devicetree/bindings/regulator/ |
| H A D | tps65090.txt | 22 entry then driver will just configure this rails as external control
|
| /linux/Documentation/networking/pse-pd/ |
| H A D | pse-pi.rst | 184 - Rail 1 and Rail 2 represent the positive and negative voltage rails, with
187 switches to change the polarity of the voltage rails, allowing for
|
| /linux/Documentation/admin-guide/media/ |
| H A D | si476x.rst | 134 0x10 afcrl Flag indicating if AFC rails
|
| /linux/arch/arm/boot/dts/st/ |
| H A D | ste-hrefv60plus.dtsi | 71 /* Name the GPIO muxed rails on the HREF boards */
|
| H A D | ste-snowball.dts | 117 /* Name the GPIO muxed rails on the Snowball board */
|
| /linux/Documentation/driver-api/ |
| H A D | slimbus.rst | 108 that corresponding clocks and/or power-rails can be turned off to save power.
|
| /linux/drivers/gpu/drm/nouveau/ |
| H A D | nouveau_hwmon.c | 252 if (!iccsense || !iccsense->data_valid || list_empty(&iccsense->rails)) in nouveau_power_is_visible()
|
| /linux/Documentation/cpu-freq/ |
| H A D | cpu-drivers.rst | 130 | | clock/voltage rails with it). |
|