| /linux/include/uapi/linux/ |
| H A D | tps6594_pfsm.h | 17 * @gpio_retention: if enabled, power rails associated with GPIO retention remain active
18 * @ddr_retention: if enabled, power rails associated with DDR retention remain active
|
| /linux/arch/arm64/boot/dts/rockchip/ |
| H A D | rk3588-jaguar-pre-ict-tester.dtso | 12 * This adapter routes some GPIOs to power rails and loops together some other
75 * GPIO3_A3 requires two power rails to be properly
97 * GPIO3_B2 requires two power rails to be properly
|
| /linux/drivers/gpu/drm/nouveau/nvkm/subdev/iccsense/ |
| H A D | base.c | 117 list_for_each_entry(rail, &iccsense->rails, head) { in nvkm_iccsense_read_all()
141 list_for_each_entry_safe(rail, tmpr, &iccsense->rails, head) { in nvkm_iccsense_dtor()
291 list_add_tail(&rail->head, &iccsense->rails); in nvkm_iccsense_oneinit()
328 INIT_LIST_HEAD(&(*iccsense)->rails); in nvkm_iccsense_new_()
|
| /linux/Documentation/devicetree/bindings/mfd/ |
| H A D | richtek,rt5120.yaml | 15 I/O, and peripheral rails in home entertainment devices. The I2C interface is
16 used for dynamic voltage scaling of the processor voltage, power rails on/off
|
| H A D | rohm,bd9571mwv.yaml | 40 This is a bitmask that specifies which DDR power rails need to be kept
|
| /linux/include/ufs/ |
| H A D | ufs_quirks.h | 68 * (atleast for 500us) from UFS rails (especially from VCCQ rail).
70 * rails in LPM mode.
|
| /linux/drivers/gpu/drm/nouveau/include/nvkm/subdev/ |
| H A D | iccsense.h | 11 struct list_head rails; member
|
| /linux/Documentation/hwmon/ |
| H A D | ucd9200.rst | 108 rails. See chip datasheets for details.
114 created for enabled rails. See chip datasheets for
|
| H A D | mp2856.rst | 31 setting of different formats on rails 1 and 2. For VID the following
|
| H A D | lochnagar.rst | 14 rails provided to the minicards. The Current Monitor does not require any
|
| H A D | mp2975.rst | 31 setting of different formats on rails 1 and 2. For VID the following
|
| H A D | ucd9000.rst | 31 sequences up to 12 independent voltage rails. The device integrates a 12-bit
|
| /linux/Documentation/devicetree/bindings/regulator/ |
| H A D | max77650-regulator.yaml | 20 three independent power rails.
|
| H A D | tps65090.txt | 22 entry then driver will just configure this rails as external control
|
| H A D | pfuze100.yaml | 57 power rails when PMIC_STBY_REQ line is asserted during the power off sequence.
|
| /linux/drivers/pmdomain/sunxi/ |
| H A D | sun50i-h6-prcm-ppu.c | 7 * block that control some power rails, most prominently for the Mali GPU.
22 * then followed by the power rails.
|
| /linux/arch/arm64/boot/dts/qcom/ |
| H A D | sa8155p.dtsi | 6 * Most notably, the RPMhPD setup differs: MMCX and LCX/LMX rails are gone,
|
| H A D | sc7180-trogdor-homestar.dtsi | 98 * rail and eDP rails are separate from each other on homestar (but
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-driver-bd9571mwv-regulator | 6 if DDR power rails will be kept powered during system suspend.
|
| /linux/Documentation/devicetree/bindings/soc/qcom/ |
| H A D | qcom-stats.yaml | 14 sleep modes involving powering down of the rails and oscillator clock.
|
| /linux/drivers/acpi/pmic/ |
| H A D | Kconfig | 8 to control power rails and sensor reading/writing on the
|
| /linux/Documentation/devicetree/bindings/input/ |
| H A D | goodix,gt7375p.yaml | 49 with what the touchscreen is expecting for its IO rails.
|
| /linux/Documentation/devicetree/bindings/display/panel/ |
| H A D | panel-dsi-cm.yaml | 45 because all its power rails can be driven by the same supply. In that case
|
| /linux/drivers/gpu/drm/amd/pm/swsmu/inc/pmfw_if/ |
| H A D | smu11_driver_if_cyan_skillfish.h | 58 // power, VF info for CPU/GFX telemetry rails, and then socket power total
|
| /linux/Documentation/driver-api/ |
| H A D | slimbus.rst | 108 that corresponding clocks and/or power-rails can be turned off to save power.
|