Searched full:interrupts (Results 7376 – 7400 of 8506) sorted by relevance
1...<<291292293294295296297298299300>>...341
| /linux/arch/arm64/boot/dts/qcom/ |
| H A D | sdm845-xiaomi-polaris.dts | 426 interrupts-extended = <&tlmm 125 0x2008>;
|
| H A D | sdm845-shift-axolotl.dts | 439 interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
|
| /linux/drivers/soc/ti/ |
| H A D | wkup_m3_ipc.c | 328 * the RX callback to avoid multiple interrupts being received in wkup_m3_ping()
|
| /linux/drivers/soc/qcom/ |
| H A D | smp2p.c | 249 /* Fire interrupts based on any value changes */ in qcom_smp2p_notify_in()
|
| /linux/arch/arm64/boot/dts/rockchip/ |
| H A D | rk3566-quartz64-b.dts | 253 interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
|
| H A D | rk3576-evb1-v10.dts | 317 interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
|
| H A D | rk3588-tiger.dtsi | 421 interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
|
| /linux/drivers/iio/light/ |
| H A D | vl6180.c | 649 /* Enable ALS and Range ready interrupts */ in vl6180_init()
|
| /linux/drivers/net/ethernet/microchip/lan966x/ |
| H A D | lan966x_main.h | 304 /* interrupts */
|
| /linux/kernel/trace/ |
| H A D | trace_sched_wakeup.c | 572 /* interrupts should be off from try_to_wake_up */ in probe_wakeup()
|
| /linux/drivers/i2c/busses/ |
| H A D | i2c-microchip-corei2c.c | 579 * control over what way the interrupts are wired for the soft cores. in mchp_corei2c_probe()
|
| H A D | i2c-synquacer.c | 287 /* Start Condition + Enable Interrupts */ in synquacer_i2c_master_start()
|
| /linux/arch/arm64/boot/dts/ti/ |
| H A D | k3-am62x-sk-common.dtsi | 410 interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
|
| /linux/drivers/mmc/host/ |
| H A D | litex_mmc.c | 497 /* Clear & enable card-change interrupts */ in litex_mmc_irq_init()
|
| /linux/drivers/platform/x86/dell/ |
| H A D | dcdbas.c | 6 * systems management software to perform System Management Interrupts (SMIs)
|
| /linux/arch/arm/boot/dts/nxp/vf/ |
| H A D | vf610-zii-scu4-aib.dts | 594 interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
|
| /linux/drivers/ata/ |
| H A D | sata_highbank.c | 583 * Software must disable interrupts prior to requesting a in ahci_highbank_suspend()
|
| /linux/include/linux/ |
| H A D | brcmphy.h | 443 #define MII_BRCM_FET_IR_MASK 0x0100 /* Mask all interrupts */
|
| H A D | virtio_config.h | 255 * interrupts, preemption and softirq disabled in virtio_synchronize_cbs()
|
| /linux/drivers/net/wireless/intel/iwlwifi/mld/ |
| H A D | iface.c | 297 * Rx filters on all MAC and increases the number of interrupts. in iwl_mld_p2p_dev_has_extended_disc()
|
| /linux/drivers/net/wireless/intersil/p54/ |
| H A D | p54spi.c | 243 /* enable host interrupts */ in p54spi_upload_firmware()
|
| /linux/arch/powerpc/kernel/ |
| H A D | kvm.c | 122 /* On relocatable kernels interrupts handlers and our code in kvm_patch_ins_b()
|
| /linux/drivers/net/phy/ |
| H A D | dp83tg720.c | 59 * cannot be reliably detected via interrupts on the DP83TG720. Therefore,
|
| /linux/arch/x86/kvm/ |
| H A D | x86.c | 2141 * other cases which must be called after interrupts are enabled on the host.
8573 * an sti; sti; sequence only disable interrupts for the first in toggle_interruptibility()
9212 * For STI, interrupts are shadowed; so KVM_REQ_EVENT will in x86_emulate_instruction()
10187 * interrupts, KVM still honors instruction boundaries in most scenarios.
10232 * "Injected" interrupts can also collide with pending exceptions if in kvm_check_and_inject_events()
10236 * exceptions, e.g. most #DBs, have higher priority than interrupts. in kvm_check_and_inject_events()
10239 * execution, and interrupts are recognized at instruction boundaries. in kvm_check_and_inject_events()
10319 /* Don't inject interrupts if the user asked to avoid doing so */ in kvm_check_and_inject_events()
10491 * When APICv gets disabled, we may still have injected interrupts in __kvm_vcpu_update_apicv()
10515 * this case so that KVM can use the AVIC doorbell to inject interrupts in kvm_vcpu_update_apicv()
[all …]
|
| /linux/drivers/scsi/lpfc/ |
| H A D | lpfc_attr.c | 3711 " 1 - poll with interrupts enabled"
3712 " 3 - poll and disable FCP ring interrupts");
4914 * @buf: string with the number of fast-path FCP interrupts per second.
4919 * maximum number of fast-path FCP interrupts per second.
4981 # lpfc_fcp_imax: The maximum number of fast-path FCP interrupts per second
4989 "Set the maximum number of FCP interrupts per second per HBA");
4999 * maximum number of fast-path FCP interrupts per second. in lpfc_param_show()
5100 * than re-enabling interrupts.
5562 # lpfc_use_msi: Use MSI (Message Signaled Interrupts) in systems that
5569 LPFC_ATTR_R(use_msi, 2, 0, 2, "Use Message Signaled Interrupts (1) or "
|
1...<<291292293294295296297298299300>>...341