| /linux/Documentation/hwmon/ |
| H A D | tmp513.rst | 56 The driver exports the shunt currents values via the following sysFs files:
84 The bus power and bus currents range and resolution depends on the calibration
|
| H A D | mc34vr500.rst | 20 monitors the temperature, input voltage and output currents and provides
|
| H A D | ltc2991.rst | 27 The LTC2991 is used to monitor system temperatures, voltages and currents.
|
| H A D | vexpress.rst | 32 providing information about power lines voltages and currents, board
|
| /linux/include/linux/power/ |
| H A D | bq2415x_charger.h | 13 * voltages and currents which can be also later configured via sysfs. If
|
| /linux/Documentation/devicetree/bindings/power/supply/ |
| H A D | x-powers,axp20x-battery-power-supply.yaml | 11 currents of the battery by reading ADC channels from the ADC.
|
| /linux/Documentation/devicetree/bindings/regulator/ |
| H A D | gpio-regulator.yaml | 57 description: Selection of available voltages/currents provided by this
|
| /linux/Documentation/sound/soc/ |
| H A D | overview.rst | 24 power via changing codec oversampling rates, bias currents, etc.
|
| /linux/Documentation/devicetree/bindings/leds/ |
| H A D | ti,tps61310.yaml | 17 In torch mode, each sink (LED1, LED2, LED3) supports currents up to 175mA.
|
| H A D | leds-lm3532.txt | 7 method allows for different LED currents in each current sink thus allowing
|
| /linux/Documentation/leds/ |
| H A D | leds-lm3556.rst | 22 from 93.75 mA to 1500 mA.The Flash currents are adjusted via the CURRENT
|
| /linux/Documentation/devicetree/bindings/iio/dac/ |
| H A D | adi,ltc2672.yaml | 79 ADC channel to monitor voltages and currents at the MUX pin.
|
| /linux/Documentation/driver-api/ |
| H A D | regulator.rst | 99 interface for this. Both take ranges of voltages and currents, supporting
|
| /linux/Documentation/devicetree/bindings/mfd/ |
| H A D | rohm,bd71828-pmic.yaml | 63 BD71827 and BD71828 have SAR ADC for measuring charging currents.
|
| /linux/drivers/power/supply/ |
| H A D | bd99954-charger.c | 351 * safety limit for combined input currents. This feels in bd9995x_power_supply_get_property()
702 /* Initialize currents/voltages and other parameters */ in bd9995x_hw_init()
|
| H A D | adp5061.c | 586 * and weak charge currents (ITRK_DEAD) in adp5061_get_property()
|
| H A D | cpcap-charger.c | 89 * CPCAP_REG_CRM charge currents. These seem to match MC13783UG.pdf
|
| /linux/drivers/mfd/ |
| H A D | max14577.c | 20 * Table of valid charger currents for different Maxim chipsets.
|
| H A D | wm8994-core.c | 551 * we can achieve a small reduction in leakage currents by in wm8994_device_init()
|
| /linux/drivers/iio/adc/ |
| H A D | ad7192.c | 621 "adi,burnout-currents-enable"); in ad7192_setup()
626 "Can't enable burnout currents: see CHOP or buffer\n"); in ad7192_setup()
|
| H A D | pac1934.c | 848 * Currents - scale for mA - depends on the in pac1934_read_raw()
|
| /linux/drivers/platform/x86/amd/pmf/ |
| H A D | pmf.h | 515 u16 currents[2]; /* in mA */ member
|
| /linux/Documentation/input/devices/ |
| H A D | joystick-parport.rst | 74 port), and combine the currents of two or more data bits together::
|
| /linux/sound/soc/codecs/ |
| H A D | tlv320aic3x.c | 1447 * possible VDD leakage currents in case the supply regulators in aic3x_set_power()
|
| /linux/drivers/net/ethernet/intel/igb/ |
| H A D | e1000_phy.c | 2143 /* Increasing ADC OPAMP stage 1 currents to max */ in igb_phy_init_script_igp3()
|