| /linux/drivers/net/phy/ |
| H A D | linkmode.c | 6 * @local_adv: local advertisement in ethtool format
7 * @partner_adv: partner advertisement in ethtool format
47 * linkmode_set_pause - set the pause mode advertisement
48 * @advertisement: advertisement in ethtool format
62 * Note: this translation from ethtool tx/rx notation to the advertisement
81 * rx=1 tx=0 gives Pause+AsymDir advertisement, but we may end up
83 * the partners advertisement.
85 * the partners advertisement allows it.
89 void linkmode_set_pause(unsigned long *advertisement, bool tx, bool rx) in linkmode_set_pause() argument
91 linkmode_mod_bit(ETHTOOL_LINK_MODE_Pause_BIT, advertisement, rx); in linkmode_set_pause()
[all …]
|
| H A D | phy-c45.c | 198 * advertisement register 7.515 and whether the status
200 * AN advertisement register 7.514.
202 * advertisement register [31:16] if supported.
261 * genphy_c45_an_config_aneg - configure advertisement registers
264 * Configure advertisement registers based on modes set in phydev->advertising
266 * Returns negative errno code on failure, 0 if advertisement didn't change,
586 * Advertisement registers filling in the link partner advertisement,
628 * genphy_c45_read_lpa - read the link partner advertisement and pause
632 * filling in the link partner advertisement, pause and asym_pause members
662 /* Read the link partner's base page advertisement */ in genphy_c45_read_lpa()
[all …]
|
| H A D | bcm-phy-lib.c | 822 * bcm_linkmode_adv_to_lre_adv_t - translate linkmode advertisement to LDS
823 * @advertising: the linkmode advertisement settings
826 * A small helper function that translates linkmode advertisement
1174 * Return: 0 if the PHY's advertisement hasn't changed, < 0 on error,
1185 /* Setup BroadR-Reach mode advertisement */ in bcm_config_lre_advert()
|
| /linux/include/linux/ |
| H A D | mdio.h | 179 * mdio45_ethtool_ksettings_get_npage() to specify advertisement bits
221 * @eee_adv: value of the MMD EEE Advertisement/Link Partner Ability registers
224 * and MMD EEE Link Partner Ability (7.61) bits to ethtool advertisement
249 * @adv: the ethtool advertisement settings
251 * A small helper function that translates ethtool advertisement settings
252 * to EEE advertisements for the MMD EEE Advertisement (7.60) and
277 * @advertising: the linkmode advertisement settings
279 * A small helper function that translates linkmode advertisement
302 * @advertising: target the linkmode advertisement settings
306 * to linkmode advertisement settings. Other bits in advertising aren't changed.
[all …]
|
| H A D | mii.h | 109 * @ethadv: the ethtool advertisement settings
111 * A small helper function that translates ethtool advertisement
137 * @advertising: the linkmode advertisement settings
139 * A small helper function that translates linkmode advertisement
168 * to ethtool advertisement settings.
192 * @ethadv: the ethtool advertisement settings
194 * A small helper function that translates ethtool advertisement
212 * @advertising: the linkmode advertisement settings
214 * A small helper function that translates linkmode advertisement
239 * advertisement settings.
[all …]
|
| H A D | phylink.h | 46 * autonegotiation advertisement. They correspond to the PAUSE and
296 * or pause modes or to change the in-band advertisement.
611 * pcs_config() - Configure the PCS mode and advertisement
619 * the advertisement mask. @permit_pause_to_mac indicates whether the
625 * For SGMII, there is no advertisement from the MAC side, the PCS should
628 * For 1000BASE-X, the advertisement should be programmed into the PCS.
630 * For most 10GBASE-R, there is no advertisement.
637 * or when the advertisement is possibly updated. It must not unnecessarily
|
| H A D | linkmode.h | 83 void linkmode_set_pause(unsigned long *advertisement, bool tx, bool rx);
|
| H A D | pim.h | 31 * 8 = Candidate-RP-Advertisement Unicast to Domain's BSR
|
| /linux/include/uapi/linux/ |
| H A D | mdio.h | 57 #define MDIO_AN_EEE_ADV 60 /* EEE advertisement */
59 #define MDIO_AN_EEE_ADV2 62 /* EEE advertisement 2 */
83 #define MDIO_AN_T1_ADV_L 514 /* BASE-T1 AN advertisement register [15:0] */
84 #define MDIO_AN_T1_ADV_M 515 /* BASE-T1 AN advertisement register [31:16] */
85 #define MDIO_AN_T1_ADV_H 516 /* BASE-T1 AN advertisement register [47:32] */
379 /* BASE-T1 auto-negotiation advertisement register [15:0] */
387 /* BASE-T1 auto-negotiation advertisement register [31:16] */
393 /* BASE-T1 auto-negotiation advertisement register [47:32] */
414 #define MDIO_AN_10BT1_AN_CTRL_ADV_EEE_T1L 0x4000 /* 10BASE-T1L EEE ability advertisement */
417 #define MDIO_AN_10BT1_AN_STAT_LPA_EEE_T1L 0x4000 /* 10BASE-T1L LP EEE ability advertisement */
[all …]
|
| H A D | rseq.h | 165 * It is now used for feature status advertisement by the kernel.
|
| /linux/drivers/net/ethernet/intel/igc/ |
| H A D | igc_phy.c | 211 * Reads the MII auto-neg advertisement register and/or the 1000T control
213 * return successful. Otherwise, setup advertisement and flow control to
226 /* Read the MII Auto-Neg Advertisement Register (Address 4). */ in igc_phy_setup_autoneg()
258 * Advertisement Register (Address 4) and the 1000 mb speed bits in in igc_phy_setup_autoneg()
316 * setup the PHY advertisement registers accordingly. If in igc_phy_setup_autoneg()
319 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto- in igc_phy_setup_autoneg()
424 * Performs initial bounds checking on autoneg advertisement parameter, then
435 /* Perform some bounds checking on the autoneg advertisement in igc_copper_link_autoneg()
446 hw_dbg("Reconfiguring auto-neg advertisement params\n"); in igc_copper_link_autoneg()
498 /* Setup autoneg and flow control advertisement and perform in igc_setup_copper_link()
|
| /linux/include/scsi/fc/ |
| H A D | fc_fip.h | 63 FIP_OP_DISC = 1, /* discovery, advertisement, etc. */
77 FIP_SC_ADV = 2, /* advertisement */
150 FIP_DT_FKA = 12, /* advertisement keep-alive period */
236 * FIP_DT_FKA - Advertisement keep-alive period.
|
| /linux/drivers/net/ethernet/chelsio/cxgb3/ |
| H A D | aq100x.c | 158 /* 10G advertisement */ in aq100x_advertise()
167 /* 1G advertisement */ in aq100x_advertise()
178 /* 100M, pause advertisement */ in aq100x_advertise()
|
| /linux/net/ipv6/ |
| H A D | ndisc_snoop.c | 162 * (Neighbor Solicitation) and 7.1.2 (Neighbor Advertisement). If valid,
174 * Neighbor Solicitation or Neighbor Advertisement.
|
| H A D | Kconfig | 25 Advertisement message which improves the ability of hosts
|
| /linux/arch/powerpc/include/asm/ |
| H A D | dt_cpu_ftrs.h | 9 * device tree feature advertisement.
|
| /linux/include/linux/netfilter/ |
| H A D | nf_conntrack_tcp.h | 27 u_int16_t last_win; /* Last window advertisement seen in dir */
|
| /linux/drivers/net/ethernet/atheros/atl1e/ |
| H A D | atl1e_hw.c | 279 * Configures PHY autoneg and flow control advertisement settings
291 /* Read the MII Auto-Neg Advertisement Register (Address 4/9). */ in atl1e_phy_setup_autoneg_adv()
305 * Advertisement Register (Address 4) and the 1000 mb speed bits in in atl1e_phy_setup_autoneg_adv()
|
| /linux/drivers/net/ethernet/intel/igb/ |
| H A D | e1000_phy.c | 788 /* when autonegotiation advertisement is only 1000Mbps then we in igb_copper_link_setup_igp()
856 * Performs initial bounds checking on autoneg advertisement parameter, then
867 /* Perform some bounds checking on the autoneg advertisement in igb_copper_link_autoneg()
878 hw_dbg("Reconfiguring auto-neg advertisement params\n"); in igb_copper_link_autoneg()
919 * Reads the MII auto-neg advertisement register and/or the 1000T control
921 * return successful. Otherwise, setup advertisement and flow control to
933 /* Read the MII Auto-Neg Advertisement Register (Address 4). */ in igb_phy_setup_autoneg()
954 * Advertisement Register (Address 4) and the 1000 mb speed bits in in igb_phy_setup_autoneg()
1000 * setup the PHY advertisement registers accordingly. If in igb_phy_setup_autoneg()
1003 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto- in igb_phy_setup_autoneg()
[all …]
|
| /linux/drivers/scsi/fcoe/ |
| H A D | fcoe_ctlr.c | 809 * That is, there have been no valid advertisement from it for 2.5
814 * Also, increment the MissDiscAdvCount when no advertisement is received
838 "Missing Discovery Advertisement " in fcoe_ctlr_age_fcfs()
881 * fcoe_ctlr_parse_adv() - Decode a FIP advertisement into a new FCF entry
882 * @fip: The FCoE controller receiving the advertisement
883 * @skb: The received FIP advertisement frame
886 * Returns zero on a valid parsed advertisement,
1014 * fcoe_ctlr_recv_adv() - Handle an incoming advertisement
1015 * @fip: The FCoE controller receiving the advertisement
1064 * ignored after a solicited advertisement is in fcoe_ctlr_recv_adv()
[all …]
|
| /linux/Documentation/litmus-tests/ |
| H A D | README | 61 What is a roach motel? This is from an old advertisement for
|
| /linux/drivers/net/ethernet/oki-semi/pch_gbe/ |
| H A D | pch_gbe_phy.c | 20 #define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
83 #define PHY_AUTONEG_ADV_DEFAULT 0x01e0 /* Autoneg Advertisement */
|
| /linux/drivers/net/ethernet/intel/e1000e/ |
| H A D | phy.c | 915 /* when autonegotiation advertisement is only 1000Mbps then we in e1000e_copper_link_setup_igp()
953 * Reads the MII auto-neg advertisement register and/or the 1000T control
955 * return successful. Otherwise, setup advertisement and flow control to
967 /* Read the MII Auto-Neg Advertisement Register (Address 4). */ in e1000_phy_setup_autoneg()
987 * Advertisement Register (Address 4) and the 1000 mb speed bits in in e1000_phy_setup_autoneg()
1032 * setup the PHY advertisement registers accordingly. If in e1000_phy_setup_autoneg()
1035 * Advertisement Register (MII_ADVERTISE) and re-start auto- in e1000_phy_setup_autoneg()
1112 * Performs initial bounds checking on autoneg advertisement parameter, then
1123 /* Perform some bounds checking on the autoneg advertisement in e1000_copper_link_autoneg()
1134 e_dbg("Reconfiguring auto-neg advertisement params\n"); in e1000_copper_link_autoneg()
[all …]
|
| /linux/drivers/net/ethernet/amd/xgbe/ |
| H A D | xgbe-mdio.c | 866 /* Set up Advertisement register */ in xgbe_an37_init()
920 /* Set up Advertisement register 3 first */ in xgbe_an73_init()
929 /* Set up Advertisement register 2 next */ in xgbe_an73_init()
944 /* Set up Advertisement register 1 last */ in xgbe_an73_init()
966 /* Set up advertisement registers based on current settings */ in xgbe_an_init()
|
| /linux/Documentation/netlink/specs/ |
| H A D | rt-route.yaml | 100 doc: A Router Advertisement withdrew the route with a zero
|