| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-driver-intel-m10-bmc-sec-update | 6 region if one is programmed, else it returns the
7 string: "hash not programmed". This file is only
16 reconfiguration region if one is programmed, else it
17 returns the string: "hash not programmed". This file
26 if one is programmed, else it returns the string:
27 "hash not programmed". This file is only visible if the
|
| H A D | sysfs-platform-silicom | 29 0 - not programmed.
30 1 - programmed.
|
| H A D | sysfs-driver-tegra-fuse | 6 data programmed at the factory. The data is laid out in 32bit
|
| H A D | sysfs-bus-iio-isl29501 | 26 light conditions. It can be programmed to correct for
|
| /linux/Documentation/misc-devices/ |
| H A D | spear-pcie-gadget.rst | 44 vendor_id returns programmed vendor id (hex)
45 device_id returns programmed device id(hex)
58 INTA, MSI or NO_INT). Select MSI only when you have programmed
63 vendor_id write vendor id(hex) to be programmed.
64 device_id write device id(hex) to be programmed.
102 check for programmed bar0 size::
|
| H A D | ad525x_dpot.rst | 9 settings. Access to the factory programmed tolerance is also provided, but
23 The tolerance files are the read-only factory programmed tolerance settings
|
| H A D | oxsemi-tornado.rst | 26 The oversampling rate is programmed with the TCR register and the clock
27 prescaler is programmed with the CPR/CPR2 register pair [OX200]_ [OX952]_
35 CPR/CPR2 register pair has to be programmed in the right order.
|
| H A D | pci-endpoint-test.rst | 15 #) verifying addresses programmed in BAR
|
| /linux/Documentation/hwmon/ |
| H A D | g760a.rst | 22 The fan speed is programmed by setting the period via 'pwm1' of two
35 speed differs more than 20% with respect to the programmed fan speed;
|
| H A D | ina209.rst | 84 register is programmed correctly before they are used. Normally this is expected
89 programmed (ie has a value not equal to zero). If so, this value is retained.
91 programmed into the calibration register.
|
| H A D | g762.rst | 45 of the programmed value for over 6 seconds 'fan1_alarm' is
64 the fan speed is programmed by setting a value between 0 and 255 via 'pwm1'
|
| /linux/Documentation/trace/coresight/ |
| H A D | coresight-config.rst | 17 Many CoreSight components can be programmed in complex ways - especially ETMs.
43 and efficient for the feature to be programmed onto the device when required.
47 will be programmed into the device hardware.
56 feature being enabled that can adjust the behaviour of the operation programmed
59 For example, this could be a count value in a programmed operation that repeats
125 In this case 'strobing' is enabled & programmed into the ETMv4.
|
| /linux/drivers/mtd/chips/ |
| H A D | Kconfig | 162 A subset of them are pre-programmed at the factory with a
166 programmable (OTP) bits; when programmed, register bits cannot be
171 Lock Register bit is programmed, the associated Protection Register
172 can only be read; it can no longer be programmed. Additionally,
173 because the Lock Register bits themselves are OTP, when programmed,
|
| /linux/Documentation/driver-api/cxl/linux/ |
| H A D | cxl-driver.rst | 335 them during boot (See `Auto Decoders` below), or on commit if programmed at
417 programmed by BIOS/EFI (see `Auto Decoders`), or by creating a region manually
428 must be programmed with the same interleave settings as the region.
466 During probe, the only decoders *required* to be programmed are `Root Decoders`.
471 All other `Switch` and `Endpoint` decoders may be programmed by the user
481 Auto Decoders are decoders programmed by BIOS/EFI at boot time, and are
490 sane - as-if validating runtime programmed regions and decoders.
500 how interleave is programmed at each decoder step, as the driver validates
587 `Memory Region` to bring this memory online with runtime programmed settings
607 `Endpoint Decoders` are programmed similar to Host Bridge and Switch decoders,
|
| /linux/Documentation/i2c/busses/ |
| H A D | i2c-amd-mp2.rst | 18 The MP2 is an ARM processor programmed as an I2C controller and communicating
|
| /linux/Documentation/networking/ |
| H A D | xsk-tx-metadata.rst | 102 The value of the launch time that is programmed in the Enhanced Normal
105 in 256 ns increments. The programmed launch time is compared against the
119 The value of the launch time that is programmed in the Advanced Transmit
|
| /linux/drivers/staging/iio/Documentation/ |
| H A D | sysfs-bus-iio-adc-ad7280a | 8 enable for the programmed amount of time, before it
|
| /linux/Documentation/leds/ |
| H A D | well-known-leds.txt | 23 The "player LEDs" are then programmed with a pattern to indicate a particular
24 player. For example, a game controller with 4 LEDs, may be programmed with "x---"
|
| /linux/Documentation/PCI/endpoint/ |
| H A D | pci-ntb-function.rst | 118 to the MSI/MSI-X address programmed by the host. The ARGUMENT
124 accessed by remote host. The allocated address should be programmed
125 in the ADDRESS register (64 bit), the size should be programmed in
126 the SIZE register and the memory window index should be programmed
|
| /linux/Documentation/devicetree/bindings/pinctrl/ |
| H A D | ti,iodelay.txt | 4 for each pin. For most part the IO delay values are programmed by the bootloader,
|
| /linux/arch/arm/boot/dts/ti/omap/ |
| H A D | am335x-osd335x-common.dtsi | 24 * The EFUSE_SMA register is not programmed for any of the AM335x wafers
|
| /linux/drivers/net/ethernet/via/ |
| H A D | Kconfig | 41 programmed I/O ports (PIO). Enabling this gives an improvement in
|
| /linux/Documentation/devicetree/bindings/mtd/ |
| H A D | fsl-upm-nand.txt | 1 Freescale Localbus UPM programmed to work with NAND flash
|
| /linux/Documentation/driver-api/cxl/platform/acpi/ |
| H A D | cedt.rst | 32 programmed by BIOS.
|
| /linux/Documentation/devicetree/bindings/mfd/ |
| H A D | max77620.txt | 34 and power-down delays (sequencing). GPIO1, GPIO2, and GPIO3 can be programmed
36 with internal regulators. 32KHz clock can be programmed to be part of a
|