/linux/Documentation/ABI/testing/ |
H A D | sysfs-bus-iio-sx9324 | 12 (DS - data shield), or measured input (MI). 16 and then measured. 18 By default, during the first phase, [PH0], CS0 is measured, 21 [PH1], CS1 is measured, CS0 and CS2 are shield: 23 [PH2], CS2 is measured, CS0 and CS1 are shield: 25 [PH3], CS1 and CS2 are measured (combo mode):
|
H A D | sysfs-bus-iio-light-si1133 | 5 Unit-less infrared intensity. The intensity is measured from 1 13 Unit-less infrared intensity. The intensity is measured from 4
|
H A D | sysfs-class-power-ltc4162l | 22 Battery input current as measured by the charger. Negative value 33 Battery voltage as measured by the charger. 43 Battery voltage, averaged over time, as measured by the charger.
|
H A D | sysfs-class-regulator | 98 measured in microvolts (i.e. E-6 Volts), for regulators 113 setting measured in microamps (i.e. E-6 Amps), for regulators 153 output voltage setting for this domain measured in microvolts, 168 output voltage setting for this domain measured in microvolts, 183 output current limit setting for this domain measured in 198 output current limit setting for this domain measured in 255 voltage setting for this domain measured in microvolts when 266 voltage setting for this domain measured in microvolts when 277 voltage setting for this domain measured in microvolts when
|
/linux/Documentation/hwmon/ |
H A D | ltc2945.rst | 46 value of the divider resistor against the measured voltage and R2 is the value 55 in1_input VIN voltage (mV). Voltage is measured either at 59 in1_lowest Lowest measured voltage 60 in1_highest Highest measured voltage 68 in2_lowest Lowest measured voltage 69 in2_highest Highest measured voltage 77 curr1_lowest Lowest measured current 78 curr1_highest Highest measured current
|
H A D | ltc2992.rst | 35 inX_lowest Minimum measured voltage. 36 inX_highest Maximum measured voltage. 43 currX_lowest Minimum measured current. 44 currX_highest Maximum measured current. 51 powerX_input_lowest Minimum measured voltage. 52 powerX_input_highest Maximum measured voltage.
|
H A D | ltc2947.rst | 29 to control a fan as a function of measured temperature. Then, the GPIO becomes 44 in0_lowest Lowest measured voltage 45 in0_highest Highest measured voltage 54 in1_lowest Lowest measured voltage 55 in1_highest Highest measured voltage 64 curr1_lowest Lowest measured current 65 curr1_highest Highest measured current
|
H A D | ltc4282.rst | 49 in0_lowest Lowest measured voltage 50 in0_highest Highest measured voltage 62 in1_lowest Lowest measured voltage 63 in1_highest Highest measured voltage 76 in2_lowest Lowest measured voltage 77 in2_highest Highest measured voltage 86 curr1_lowest Lowest measured current 87 curr1_highest Highest measured current
|
H A D | lm25066.rst | 100 in1_average Average measured input voltage. 116 in3_average Average measured output voltage. 122 curr1_average Average measured input current. 128 power1_average Average measured input power.
|
H A D | lt7182s.rst | 52 curr[3-4]_highest Highest measured output current 58 in[1-2]_highest Highest measured input voltage 74 in[3-4|6-7]_highest Highest measured output voltage
|
H A D | adt7462.rst | 31 response to the measured temperatures without further host intervention. This 34 Each of the measured inputs (voltage, temperature, fan speed) has 36 any measured value exceeds either limit.
|
H A D | w83793.rst | 65 For voltage sensors, an alarm triggers if the measured value is below 67 For temperature sensors, an alarm triggers if the measured value goes 68 above the high temperature limit, and wears off only after the measured 70 For fan sensors, an alarm triggers if the measured value is below the
|
H A D | adt7470.rst | 31 response to the measured temperatures with further host intervention. This 34 Each of the measured inputs (temperature, fan speed) has corresponding high/low 35 limit values. The ADT7470 will signal an ALARM if any measured value exceeds
|
H A D | g760a.rst | 29 The measured fan rotation speed returned via 'fan1_input' is derived 30 from the measured speed pulse period by assuming again a 32kHz clock
|
H A D | tmp401.rst | 58 remote and one local temperature sensors. Temperature is measured in degrees 70 * Minimum and Maximum temperature measured since power-on, chip-reset
|
H A D | smsc47m192.rst | 42 Voltages and temperatures are measured by an 8-bit ADC, the resolution 85 temp1_input chip temperature measured by on-chip diode 86 temp[2-3]_input temperature measured by external diodes (one of these
|
H A D | pc87427.rst | 39 signal. Speeds down to 83 RPM can be measured. 42 limit. Another alarm is triggered if the speed is too low to be measured
|
H A D | lm85.rst | 100 voltage can be measured without external resistors: 104 The temperatures measured are one internal diode, and two remote diodes. 114 response to the measured temperatures without further host intervention. 117 Each of the measured inputs (voltage, temperature, fan speed) has 119 measured value exceeds either limit. 284 adjust the Tmin value to maintain the measured temperature sensor at a
|
H A D | adt7475.rst | 66 response to the measured temperatures without further host intervention. 69 Each of the measured inputs (voltage, temperature, fan speed) has 71 any measured value exceeds either limit.
|
H A D | k10temp.rst | 104 available as temp1_input in sysfs. It is measured in degrees Celsius with a 110 arbitrary scale measured in degrees. It does _not_ represent an actual 123 the reported temperature (Tctl). Tdie is the real measured temperature, and
|
H A D | adm1026.rst | 49 Temperatures are measured in degrees Celsius. There are two external 57 Fan rotation speeds are reported in RPM (rotations per minute) but measured 82 The ADM1026 measures continuously. Analog inputs are measured about 4
|
/linux/Documentation/admin-guide/device-mapper/ |
H A D | dm-ima.rst | 32 - and re-measured - triggered on state/configuration change. 65 It contains data for the specific event to be measured, 71 EVENT_DATA := The event data to be measured. 76 | The DM target data measured by IMA subsystem can alternatively 101 targets in the table are measured. 136 in the buffer (say from target 0 to x) is measured in a given IMA event. 137 … The remaining data from targets x+1 to N-1 is measured in the subsequent IMA events, 171 data from previous load of an active table are measured. 183 Rerpresents the hash of the IMA data being measured for the 209 data from an active and inactive table are measured. [all …]
|
/linux/Documentation/devicetree/bindings/sound/ |
H A D | rt1011.txt | 26 u32. The temperature was measured while doing the calibration. Units: Celsius degree 29 u32. This is r0 calibration data which was measured in factory mode.
|
/linux/Documentation/driver-api/thermal/ |
H A D | exynos_thermal.rst | 19 The chip only exposes the measured 8-bit temperature code value 41 Temperature code measured at 25 degree Celsius which is unchanged 44 Temperature code measured at 85 degree Celsius which is unchanged
|
/linux/Documentation/userspace-api/media/v4l/ |
H A D | pixfmt-packed-hsv.rst | 12 The *hue* (h) is measured in degrees, the equivalence between degrees and LSBs 14 The *saturation* (s) and the *value* (v) are measured in percentage of the
|