| /linux/arch/arm/boot/dts/ti/omap/ |
| H A D | am3517-craneboard.dts | 47 /* goes to expansion connector */
53 /* goes to expansion connector */
63 /* goes to expansion connector */
68 /* goes to expansion connector */
|
| /linux/Documentation/userspace-api/media/cec/ |
| H A D | cec-ioc-dqevent.rst | 157 - Generated if the CEC pin goes from a high voltage to a low voltage.
164 - Generated if the CEC pin goes from a low voltage to a high voltage.
171 - Generated if the HPD pin goes from a high voltage to a low voltage.
180 - Generated if the HPD pin goes from a low voltage to a high voltage.
189 - Generated if the 5V pin goes from a high voltage to a low voltage.
198 - Generated if the 5V pin goes from a low voltage to a high voltage.
|
| /linux/Documentation/hwmon/ |
| H A D | ds620.rst | 32 stays active until the temperature goes above temp1_max.
35 output pin becomes active when the temperature goes above temp1_max and stays
|
| H A D | lm87.rst | 44 goes above it, and an alarm is also produced when the value goes below
|
| /linux/tools/perf/Documentation/ |
| H A D | perf-kwork.txt | 110 stop time is not given (i.e, time string is 'x.y,') then analysis goes
140 stop time is not given (i.e, time string is 'x.y,') then analysis goes
182 stop time is not given (i.e, time string is 'x.y,') then analysis goes
212 stop time is not given (i.e, time string is 'x.y,') then analysis goes
|
| H A D | perf-kmem.txt | 75 stop time is not given (i.e, time string is 'x.y,') then analysis goes
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-iio-adc-hi8435 | 16 Channel Y low voltage threshold. If sensor input voltage goes lower then
35 Channel Y high voltage threshold. If sensor input voltage goes higher then
|
| H A D | debugfs-pfo-nx-crypto | 19 recorded here (the hcall will retry until -EBUSY goes away).
|
| /linux/Documentation/leds/ |
| H A D | ledtrig-oneshot.rst | 34 interface goes up::
42 interface goes down::
|
| /linux/arch/arm64/boot/dts/qcom/ |
| H A D | sc7280-herobrine-herobrine-r1.dts | 132 * This pin goes to the display panel but then doesn't actually do anything
144 * - If a pin goes to herobrine board and is named it gets that name.
145 * - If a pin goes to herobrine board and is not named, it gets no name.
|
| H A D | sc7280-herobrine-crd.dts | 142 * This pin goes to the display panel but then doesn't actually do anything
154 * - If a pin goes to CRD board and is named it gets that name.
155 * - If a pin goes to CRD board and is not named, it gets no name.
|
| H A D | sc7280-herobrine-zombie.dtsi | 87 * - If a pin goes to herobrine board and is named it gets that name.
88 * - If a pin goes to herobrine board and is not named, it gets no name.
|
| H A D | sc7280-herobrine-villager.dtsi | 101 * - If a pin goes to herobrine board and is named it gets that name.
102 * - If a pin goes to herobrine board and is not named, it gets no name.
|
| H A D | sc7280-herobrine-evoker.dtsi | 111 * - If a pin goes to herobrine board and is named it gets that name.
112 * - If a pin goes to herobrine board and is not named, it gets no name.
|
| /linux/Documentation/usb/ |
| H A D | dwc3.rst | 30 goes through every event and calls generic_handle_irq() for event
32 counter so interrupt goes away (eventually).
|
| /linux/fs/ |
| H A D | pnode.c | 472 bool goes = true; in chain_busy() local
477 goes = false; in chain_busy()
481 if (goes && next && next != m->overmount && above && m != deepest) in chain_busy()
482 goes = false; in chain_busy()
485 if (goes && do_refcount_check(m, 1)) in chain_busy()
|
| /linux/drivers/net/wireless/marvell/libertas/ |
| H A D | README | 149 This event is generated when the average received RSSI in beacons goes
153 This event is generated when the average received RSSI in beacons goes
157 This event is generated when the average received SNR in beacons goes
161 This event is generated when the average received SNR in beacons goes
|
| /linux/Documentation/bpf/ |
| H A D | index.rst | 10 that goes into great technical depth about the BPF Architecture.
|
| /linux/arch/m68k/kernel/ |
| H A D | vmlinux-sun3.lds | 33 /* End of data goes *here* so that freeing init code works properly. */
|
| /linux/Documentation/arch/x86/ |
| H A D | booting-dt.rst | 7 the decompressor (the real mode entry point goes to the same 32bit
|
| /linux/Documentation/input/devices/ |
| H A D | pxrc.rst | 15 Many RC controllers is able to configure which stick goes to which channel.
|
| /linux/arch/m68k/ |
| H A D | Kconfig.debug | 16 Where implemented, output goes to the framebuffer as well.
|
| /linux/Documentation/driver-api/nfc/ |
| H A D | nfc-pn544.rst | 10 communication. The driver goes under drives/nfc/ and is compiled as a
|
| /linux/scripts/ |
| H A D | head-object-list.txt | 8 # The code marked as __HEAD goes into the ".head.text" section, which is placed
|
| /linux/Documentation/userspace-api/ |
| H A D | tee.rst | 38 supplicants the communication goes in the other direction, the TEE sends
|