1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Driver for the PSC of the Freescale MPC52xx PSCs configured as UARTs.
4 *
5 * FIXME According to the usermanual the status bits in the status register
6 * are only updated when the peripherals access the FIFO and not when the
7 * CPU access them. So since we use this bits to know when we stop writing
8 * and reading, they may not be updated in-time and a race condition may
9 * exists. But I haven't be able to prove this and I don't care. But if
10 * any problem arises, it might worth checking. The TX/RX FIFO Stats
11 * registers should be used in addition.
12 * Update: Actually, they seem updated ... At least the bits we use.
13 *
14 *
15 * Maintainer : Sylvain Munaut <tnt@246tNt.com>
16 *
17 * Some of the code has been inspired/copied from the 2.4 code written
18 * by Dale Farnsworth <dfarnsworth@mvista.com>.
19 *
20 * Copyright (C) 2008 Freescale Semiconductor Inc.
21 * John Rigby <jrigby@gmail.com>
22 * Added support for MPC5121
23 * Copyright (C) 2006 Secret Lab Technologies Ltd.
24 * Grant Likely <grant.likely@secretlab.ca>
25 * Copyright (C) 2004-2006 Sylvain Munaut <tnt@246tNt.com>
26 * Copyright (C) 2003 MontaVista, Software, Inc.
27 */
28
29 #undef DEBUG
30
31 #include <linux/device.h>
32 #include <linux/module.h>
33 #include <linux/tty.h>
34 #include <linux/tty_flip.h>
35 #include <linux/serial.h>
36 #include <linux/sysrq.h>
37 #include <linux/console.h>
38 #include <linux/delay.h>
39 #include <linux/io.h>
40 #include <linux/of.h>
41 #include <linux/of_address.h>
42 #include <linux/of_irq.h>
43 #include <linux/platform_device.h>
44 #include <linux/clk.h>
45
46 #include <asm/mpc52xx.h>
47 #include <asm/mpc52xx_psc.h>
48
49 #include <linux/serial_core.h>
50
51
52 /* We've been assigned a range on the "Low-density serial ports" major */
53 #define SERIAL_PSC_MAJOR 204
54 #define SERIAL_PSC_MINOR 148
55
56
57 #define ISR_PASS_LIMIT 256 /* Max number of iteration in the interrupt */
58
59
60 static struct uart_port mpc52xx_uart_ports[MPC52xx_PSC_MAXNUM];
61 /* Rem: - We use the read_status_mask as a shadow of
62 * psc->mpc52xx_psc_imr
63 * - It's important that is array is all zero on start as we
64 * use it to know if it's initialized or not ! If it's not sure
65 * it's cleared, then a memset(...,0,...) should be added to
66 * the console_init
67 */
68
69 /* lookup table for matching device nodes to index numbers */
70 static struct device_node *mpc52xx_uart_nodes[MPC52xx_PSC_MAXNUM];
71
72 static void mpc52xx_uart_of_enumerate(void);
73
74
75 #define PSC(port) ((struct mpc52xx_psc __iomem *)((port)->membase))
76
77
78 /* Forward declaration of the interruption handling routine */
79 static irqreturn_t mpc52xx_uart_int(int irq, void *dev_id);
80 static irqreturn_t mpc5xxx_uart_process_int(struct uart_port *port);
81
82 /* ======================================================================== */
83 /* PSC fifo operations for isolating differences between 52xx and 512x */
84 /* ======================================================================== */
85
86 struct psc_ops {
87 void (*fifo_init)(struct uart_port *port);
88 unsigned int (*raw_rx_rdy)(struct uart_port *port);
89 unsigned int (*raw_tx_rdy)(struct uart_port *port);
90 unsigned int (*rx_rdy)(struct uart_port *port);
91 unsigned int (*tx_rdy)(struct uart_port *port);
92 unsigned int (*tx_empty)(struct uart_port *port);
93 void (*stop_rx)(struct uart_port *port);
94 void (*start_tx)(struct uart_port *port);
95 void (*stop_tx)(struct uart_port *port);
96 void (*rx_clr_irq)(struct uart_port *port);
97 void (*tx_clr_irq)(struct uart_port *port);
98 void (*write_char)(struct uart_port *port, unsigned char c);
99 unsigned char (*read_char)(struct uart_port *port);
100 void (*cw_disable_ints)(struct uart_port *port);
101 void (*cw_restore_ints)(struct uart_port *port);
102 unsigned int (*set_baudrate)(struct uart_port *port,
103 struct ktermios *new,
104 const struct ktermios *old);
105 int (*clock_alloc)(struct uart_port *port);
106 void (*clock_relse)(struct uart_port *port);
107 int (*clock)(struct uart_port *port, int enable);
108 int (*fifoc_init)(void);
109 void (*fifoc_uninit)(void);
110 void (*get_irq)(struct uart_port *, struct device_node *);
111 irqreturn_t (*handle_irq)(struct uart_port *port);
112 u16 (*get_status)(struct uart_port *port);
113 u8 (*get_ipcr)(struct uart_port *port);
114 void (*command)(struct uart_port *port, u8 cmd);
115 void (*set_mode)(struct uart_port *port, u8 mr1, u8 mr2);
116 void (*set_rts)(struct uart_port *port, int state);
117 void (*enable_ms)(struct uart_port *port);
118 void (*set_sicr)(struct uart_port *port, u32 val);
119 void (*set_imr)(struct uart_port *port, u16 val);
120 u8 (*get_mr1)(struct uart_port *port);
121 };
122
123 /* setting the prescaler and divisor reg is common for all chips */
mpc52xx_set_divisor(struct mpc52xx_psc __iomem * psc,u16 prescaler,unsigned int divisor)124 static inline void mpc52xx_set_divisor(struct mpc52xx_psc __iomem *psc,
125 u16 prescaler, unsigned int divisor)
126 {
127 /* select prescaler */
128 out_be16(&psc->mpc52xx_psc_clock_select, prescaler);
129 out_8(&psc->ctur, divisor >> 8);
130 out_8(&psc->ctlr, divisor & 0xff);
131 }
132
mpc52xx_psc_get_status(struct uart_port * port)133 static u16 mpc52xx_psc_get_status(struct uart_port *port)
134 {
135 return in_be16(&PSC(port)->mpc52xx_psc_status);
136 }
137
mpc52xx_psc_get_ipcr(struct uart_port * port)138 static u8 mpc52xx_psc_get_ipcr(struct uart_port *port)
139 {
140 return in_8(&PSC(port)->mpc52xx_psc_ipcr);
141 }
142
mpc52xx_psc_command(struct uart_port * port,u8 cmd)143 static void mpc52xx_psc_command(struct uart_port *port, u8 cmd)
144 {
145 out_8(&PSC(port)->command, cmd);
146 }
147
mpc52xx_psc_set_mode(struct uart_port * port,u8 mr1,u8 mr2)148 static void mpc52xx_psc_set_mode(struct uart_port *port, u8 mr1, u8 mr2)
149 {
150 out_8(&PSC(port)->command, MPC52xx_PSC_SEL_MODE_REG_1);
151 out_8(&PSC(port)->mode, mr1);
152 out_8(&PSC(port)->mode, mr2);
153 }
154
mpc52xx_psc_set_rts(struct uart_port * port,int state)155 static void mpc52xx_psc_set_rts(struct uart_port *port, int state)
156 {
157 if (state)
158 out_8(&PSC(port)->op1, MPC52xx_PSC_OP_RTS);
159 else
160 out_8(&PSC(port)->op0, MPC52xx_PSC_OP_RTS);
161 }
162
mpc52xx_psc_enable_ms(struct uart_port * port)163 static void mpc52xx_psc_enable_ms(struct uart_port *port)
164 {
165 struct mpc52xx_psc __iomem *psc = PSC(port);
166
167 /* clear D_*-bits by reading them */
168 in_8(&psc->mpc52xx_psc_ipcr);
169 /* enable CTS and DCD as IPC interrupts */
170 out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
171
172 port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
173 out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
174 }
175
mpc52xx_psc_set_sicr(struct uart_port * port,u32 val)176 static void mpc52xx_psc_set_sicr(struct uart_port *port, u32 val)
177 {
178 out_be32(&PSC(port)->sicr, val);
179 }
180
mpc52xx_psc_set_imr(struct uart_port * port,u16 val)181 static void mpc52xx_psc_set_imr(struct uart_port *port, u16 val)
182 {
183 out_be16(&PSC(port)->mpc52xx_psc_imr, val);
184 }
185
mpc52xx_psc_get_mr1(struct uart_port * port)186 static u8 mpc52xx_psc_get_mr1(struct uart_port *port)
187 {
188 out_8(&PSC(port)->command, MPC52xx_PSC_SEL_MODE_REG_1);
189 return in_8(&PSC(port)->mode);
190 }
191
192 #ifdef CONFIG_PPC_MPC52xx
193 #define FIFO_52xx(port) ((struct mpc52xx_psc_fifo __iomem *)(PSC(port)+1))
mpc52xx_psc_fifo_init(struct uart_port * port)194 static void mpc52xx_psc_fifo_init(struct uart_port *port)
195 {
196 struct mpc52xx_psc __iomem *psc = PSC(port);
197 struct mpc52xx_psc_fifo __iomem *fifo = FIFO_52xx(port);
198
199 out_8(&fifo->rfcntl, 0x00);
200 out_be16(&fifo->rfalarm, 0x1ff);
201 out_8(&fifo->tfcntl, 0x07);
202 out_be16(&fifo->tfalarm, 0x80);
203
204 port->read_status_mask |= MPC52xx_PSC_IMR_RXRDY | MPC52xx_PSC_IMR_TXRDY;
205 out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
206 }
207
mpc52xx_psc_raw_rx_rdy(struct uart_port * port)208 static unsigned int mpc52xx_psc_raw_rx_rdy(struct uart_port *port)
209 {
210 return in_be16(&PSC(port)->mpc52xx_psc_status)
211 & MPC52xx_PSC_SR_RXRDY;
212 }
213
mpc52xx_psc_raw_tx_rdy(struct uart_port * port)214 static unsigned int mpc52xx_psc_raw_tx_rdy(struct uart_port *port)
215 {
216 return in_be16(&PSC(port)->mpc52xx_psc_status)
217 & MPC52xx_PSC_SR_TXRDY;
218 }
219
220
mpc52xx_psc_rx_rdy(struct uart_port * port)221 static unsigned int mpc52xx_psc_rx_rdy(struct uart_port *port)
222 {
223 return in_be16(&PSC(port)->mpc52xx_psc_isr)
224 & port->read_status_mask
225 & MPC52xx_PSC_IMR_RXRDY;
226 }
227
mpc52xx_psc_tx_rdy(struct uart_port * port)228 static unsigned int mpc52xx_psc_tx_rdy(struct uart_port *port)
229 {
230 return in_be16(&PSC(port)->mpc52xx_psc_isr)
231 & port->read_status_mask
232 & MPC52xx_PSC_IMR_TXRDY;
233 }
234
mpc52xx_psc_tx_empty(struct uart_port * port)235 static unsigned int mpc52xx_psc_tx_empty(struct uart_port *port)
236 {
237 u16 sts = in_be16(&PSC(port)->mpc52xx_psc_status);
238
239 return (sts & MPC52xx_PSC_SR_TXEMP) ? TIOCSER_TEMT : 0;
240 }
241
mpc52xx_psc_start_tx(struct uart_port * port)242 static void mpc52xx_psc_start_tx(struct uart_port *port)
243 {
244 port->read_status_mask |= MPC52xx_PSC_IMR_TXRDY;
245 out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask);
246 }
247
mpc52xx_psc_stop_tx(struct uart_port * port)248 static void mpc52xx_psc_stop_tx(struct uart_port *port)
249 {
250 port->read_status_mask &= ~MPC52xx_PSC_IMR_TXRDY;
251 out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask);
252 }
253
mpc52xx_psc_stop_rx(struct uart_port * port)254 static void mpc52xx_psc_stop_rx(struct uart_port *port)
255 {
256 port->read_status_mask &= ~MPC52xx_PSC_IMR_RXRDY;
257 out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask);
258 }
259
mpc52xx_psc_rx_clr_irq(struct uart_port * port)260 static void mpc52xx_psc_rx_clr_irq(struct uart_port *port)
261 {
262 }
263
mpc52xx_psc_tx_clr_irq(struct uart_port * port)264 static void mpc52xx_psc_tx_clr_irq(struct uart_port *port)
265 {
266 }
267
mpc52xx_psc_write_char(struct uart_port * port,unsigned char c)268 static void mpc52xx_psc_write_char(struct uart_port *port, unsigned char c)
269 {
270 out_8(&PSC(port)->mpc52xx_psc_buffer_8, c);
271 }
272
mpc52xx_psc_read_char(struct uart_port * port)273 static unsigned char mpc52xx_psc_read_char(struct uart_port *port)
274 {
275 return in_8(&PSC(port)->mpc52xx_psc_buffer_8);
276 }
277
mpc52xx_psc_cw_disable_ints(struct uart_port * port)278 static void mpc52xx_psc_cw_disable_ints(struct uart_port *port)
279 {
280 out_be16(&PSC(port)->mpc52xx_psc_imr, 0);
281 }
282
mpc52xx_psc_cw_restore_ints(struct uart_port * port)283 static void mpc52xx_psc_cw_restore_ints(struct uart_port *port)
284 {
285 out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask);
286 }
287
mpc5200_psc_set_baudrate(struct uart_port * port,struct ktermios * new,const struct ktermios * old)288 static unsigned int mpc5200_psc_set_baudrate(struct uart_port *port,
289 struct ktermios *new,
290 const struct ktermios *old)
291 {
292 unsigned int baud;
293 unsigned int divisor;
294
295 /* The 5200 has a fixed /32 prescaler, uartclk contains the ipb freq */
296 baud = uart_get_baud_rate(port, new, old,
297 port->uartclk / (32 * 0xffff) + 1,
298 port->uartclk / 32);
299 divisor = (port->uartclk + 16 * baud) / (32 * baud);
300
301 /* enable the /32 prescaler and set the divisor */
302 mpc52xx_set_divisor(PSC(port), 0xdd00, divisor);
303 return baud;
304 }
305
mpc5200b_psc_set_baudrate(struct uart_port * port,struct ktermios * new,const struct ktermios * old)306 static unsigned int mpc5200b_psc_set_baudrate(struct uart_port *port,
307 struct ktermios *new,
308 const struct ktermios *old)
309 {
310 unsigned int baud;
311 unsigned int divisor;
312 u16 prescaler;
313
314 /* The 5200B has a selectable /4 or /32 prescaler, uartclk contains the
315 * ipb freq */
316 baud = uart_get_baud_rate(port, new, old,
317 port->uartclk / (32 * 0xffff) + 1,
318 port->uartclk / 4);
319 divisor = (port->uartclk + 2 * baud) / (4 * baud);
320
321 /* select the proper prescaler and set the divisor
322 * prefer high prescaler for more tolerance on low baudrates */
323 if (divisor > 0xffff || baud <= 115200) {
324 divisor = (divisor + 4) / 8;
325 prescaler = 0xdd00; /* /32 */
326 } else
327 prescaler = 0xff00; /* /4 */
328 mpc52xx_set_divisor(PSC(port), prescaler, divisor);
329 return baud;
330 }
331
mpc52xx_psc_get_irq(struct uart_port * port,struct device_node * np)332 static void mpc52xx_psc_get_irq(struct uart_port *port, struct device_node *np)
333 {
334 port->irqflags = 0;
335 port->irq = irq_of_parse_and_map(np, 0);
336 }
337
338 /* 52xx specific interrupt handler. The caller holds the port lock */
mpc52xx_psc_handle_irq(struct uart_port * port)339 static irqreturn_t mpc52xx_psc_handle_irq(struct uart_port *port)
340 {
341 return mpc5xxx_uart_process_int(port);
342 }
343
344 static const struct psc_ops mpc52xx_psc_ops = {
345 .fifo_init = mpc52xx_psc_fifo_init,
346 .raw_rx_rdy = mpc52xx_psc_raw_rx_rdy,
347 .raw_tx_rdy = mpc52xx_psc_raw_tx_rdy,
348 .rx_rdy = mpc52xx_psc_rx_rdy,
349 .tx_rdy = mpc52xx_psc_tx_rdy,
350 .tx_empty = mpc52xx_psc_tx_empty,
351 .stop_rx = mpc52xx_psc_stop_rx,
352 .start_tx = mpc52xx_psc_start_tx,
353 .stop_tx = mpc52xx_psc_stop_tx,
354 .rx_clr_irq = mpc52xx_psc_rx_clr_irq,
355 .tx_clr_irq = mpc52xx_psc_tx_clr_irq,
356 .write_char = mpc52xx_psc_write_char,
357 .read_char = mpc52xx_psc_read_char,
358 .cw_disable_ints = mpc52xx_psc_cw_disable_ints,
359 .cw_restore_ints = mpc52xx_psc_cw_restore_ints,
360 .set_baudrate = mpc5200_psc_set_baudrate,
361 .get_irq = mpc52xx_psc_get_irq,
362 .handle_irq = mpc52xx_psc_handle_irq,
363 .get_status = mpc52xx_psc_get_status,
364 .get_ipcr = mpc52xx_psc_get_ipcr,
365 .command = mpc52xx_psc_command,
366 .set_mode = mpc52xx_psc_set_mode,
367 .set_rts = mpc52xx_psc_set_rts,
368 .enable_ms = mpc52xx_psc_enable_ms,
369 .set_sicr = mpc52xx_psc_set_sicr,
370 .set_imr = mpc52xx_psc_set_imr,
371 .get_mr1 = mpc52xx_psc_get_mr1,
372 };
373
374 static const struct psc_ops mpc5200b_psc_ops = {
375 .fifo_init = mpc52xx_psc_fifo_init,
376 .raw_rx_rdy = mpc52xx_psc_raw_rx_rdy,
377 .raw_tx_rdy = mpc52xx_psc_raw_tx_rdy,
378 .rx_rdy = mpc52xx_psc_rx_rdy,
379 .tx_rdy = mpc52xx_psc_tx_rdy,
380 .tx_empty = mpc52xx_psc_tx_empty,
381 .stop_rx = mpc52xx_psc_stop_rx,
382 .start_tx = mpc52xx_psc_start_tx,
383 .stop_tx = mpc52xx_psc_stop_tx,
384 .rx_clr_irq = mpc52xx_psc_rx_clr_irq,
385 .tx_clr_irq = mpc52xx_psc_tx_clr_irq,
386 .write_char = mpc52xx_psc_write_char,
387 .read_char = mpc52xx_psc_read_char,
388 .cw_disable_ints = mpc52xx_psc_cw_disable_ints,
389 .cw_restore_ints = mpc52xx_psc_cw_restore_ints,
390 .set_baudrate = mpc5200b_psc_set_baudrate,
391 .get_irq = mpc52xx_psc_get_irq,
392 .handle_irq = mpc52xx_psc_handle_irq,
393 .get_status = mpc52xx_psc_get_status,
394 .get_ipcr = mpc52xx_psc_get_ipcr,
395 .command = mpc52xx_psc_command,
396 .set_mode = mpc52xx_psc_set_mode,
397 .set_rts = mpc52xx_psc_set_rts,
398 .enable_ms = mpc52xx_psc_enable_ms,
399 .set_sicr = mpc52xx_psc_set_sicr,
400 .set_imr = mpc52xx_psc_set_imr,
401 .get_mr1 = mpc52xx_psc_get_mr1,
402 };
403
404 #endif /* CONFIG_PPC_MPC52xx */
405
406 #ifdef CONFIG_PPC_MPC512x
407 #define FIFO_512x(port) ((struct mpc512x_psc_fifo __iomem *)(PSC(port)+1))
408
409 /* PSC FIFO Controller for mpc512x */
410 struct psc_fifoc {
411 u32 fifoc_cmd;
412 u32 fifoc_int;
413 u32 fifoc_dma;
414 u32 fifoc_axe;
415 u32 fifoc_debug;
416 };
417
418 static struct psc_fifoc __iomem *psc_fifoc;
419 static unsigned int psc_fifoc_irq;
420 static struct clk *psc_fifoc_clk;
421
mpc512x_psc_fifo_init(struct uart_port * port)422 static void mpc512x_psc_fifo_init(struct uart_port *port)
423 {
424 /* /32 prescaler */
425 out_be16(&PSC(port)->mpc52xx_psc_clock_select, 0xdd00);
426
427 out_be32(&FIFO_512x(port)->txcmd, MPC512x_PSC_FIFO_RESET_SLICE);
428 out_be32(&FIFO_512x(port)->txcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
429 out_be32(&FIFO_512x(port)->txalarm, 1);
430 out_be32(&FIFO_512x(port)->tximr, 0);
431
432 out_be32(&FIFO_512x(port)->rxcmd, MPC512x_PSC_FIFO_RESET_SLICE);
433 out_be32(&FIFO_512x(port)->rxcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
434 out_be32(&FIFO_512x(port)->rxalarm, 1);
435 out_be32(&FIFO_512x(port)->rximr, 0);
436
437 out_be32(&FIFO_512x(port)->tximr, MPC512x_PSC_FIFO_ALARM);
438 out_be32(&FIFO_512x(port)->rximr, MPC512x_PSC_FIFO_ALARM);
439 }
440
mpc512x_psc_raw_rx_rdy(struct uart_port * port)441 static unsigned int mpc512x_psc_raw_rx_rdy(struct uart_port *port)
442 {
443 return !(in_be32(&FIFO_512x(port)->rxsr) & MPC512x_PSC_FIFO_EMPTY);
444 }
445
mpc512x_psc_raw_tx_rdy(struct uart_port * port)446 static unsigned int mpc512x_psc_raw_tx_rdy(struct uart_port *port)
447 {
448 return !(in_be32(&FIFO_512x(port)->txsr) & MPC512x_PSC_FIFO_FULL);
449 }
450
mpc512x_psc_rx_rdy(struct uart_port * port)451 static unsigned int mpc512x_psc_rx_rdy(struct uart_port *port)
452 {
453 return in_be32(&FIFO_512x(port)->rxsr)
454 & in_be32(&FIFO_512x(port)->rximr)
455 & MPC512x_PSC_FIFO_ALARM;
456 }
457
mpc512x_psc_tx_rdy(struct uart_port * port)458 static unsigned int mpc512x_psc_tx_rdy(struct uart_port *port)
459 {
460 return in_be32(&FIFO_512x(port)->txsr)
461 & in_be32(&FIFO_512x(port)->tximr)
462 & MPC512x_PSC_FIFO_ALARM;
463 }
464
mpc512x_psc_tx_empty(struct uart_port * port)465 static unsigned int mpc512x_psc_tx_empty(struct uart_port *port)
466 {
467 return in_be32(&FIFO_512x(port)->txsr)
468 & MPC512x_PSC_FIFO_EMPTY;
469 }
470
mpc512x_psc_stop_rx(struct uart_port * port)471 static void mpc512x_psc_stop_rx(struct uart_port *port)
472 {
473 unsigned long rx_fifo_imr;
474
475 rx_fifo_imr = in_be32(&FIFO_512x(port)->rximr);
476 rx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
477 out_be32(&FIFO_512x(port)->rximr, rx_fifo_imr);
478 }
479
mpc512x_psc_start_tx(struct uart_port * port)480 static void mpc512x_psc_start_tx(struct uart_port *port)
481 {
482 unsigned long tx_fifo_imr;
483
484 tx_fifo_imr = in_be32(&FIFO_512x(port)->tximr);
485 tx_fifo_imr |= MPC512x_PSC_FIFO_ALARM;
486 out_be32(&FIFO_512x(port)->tximr, tx_fifo_imr);
487 }
488
mpc512x_psc_stop_tx(struct uart_port * port)489 static void mpc512x_psc_stop_tx(struct uart_port *port)
490 {
491 unsigned long tx_fifo_imr;
492
493 tx_fifo_imr = in_be32(&FIFO_512x(port)->tximr);
494 tx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
495 out_be32(&FIFO_512x(port)->tximr, tx_fifo_imr);
496 }
497
mpc512x_psc_rx_clr_irq(struct uart_port * port)498 static void mpc512x_psc_rx_clr_irq(struct uart_port *port)
499 {
500 out_be32(&FIFO_512x(port)->rxisr, in_be32(&FIFO_512x(port)->rxisr));
501 }
502
mpc512x_psc_tx_clr_irq(struct uart_port * port)503 static void mpc512x_psc_tx_clr_irq(struct uart_port *port)
504 {
505 out_be32(&FIFO_512x(port)->txisr, in_be32(&FIFO_512x(port)->txisr));
506 }
507
mpc512x_psc_write_char(struct uart_port * port,unsigned char c)508 static void mpc512x_psc_write_char(struct uart_port *port, unsigned char c)
509 {
510 out_8(&FIFO_512x(port)->txdata_8, c);
511 }
512
mpc512x_psc_read_char(struct uart_port * port)513 static unsigned char mpc512x_psc_read_char(struct uart_port *port)
514 {
515 return in_8(&FIFO_512x(port)->rxdata_8);
516 }
517
mpc512x_psc_cw_disable_ints(struct uart_port * port)518 static void mpc512x_psc_cw_disable_ints(struct uart_port *port)
519 {
520 port->read_status_mask =
521 in_be32(&FIFO_512x(port)->tximr) << 16 |
522 in_be32(&FIFO_512x(port)->rximr);
523 out_be32(&FIFO_512x(port)->tximr, 0);
524 out_be32(&FIFO_512x(port)->rximr, 0);
525 }
526
mpc512x_psc_cw_restore_ints(struct uart_port * port)527 static void mpc512x_psc_cw_restore_ints(struct uart_port *port)
528 {
529 out_be32(&FIFO_512x(port)->tximr,
530 (port->read_status_mask >> 16) & 0x7f);
531 out_be32(&FIFO_512x(port)->rximr, port->read_status_mask & 0x7f);
532 }
533
mpc512x_psc_set_baudrate(struct uart_port * port,struct ktermios * new,const struct ktermios * old)534 static unsigned int mpc512x_psc_set_baudrate(struct uart_port *port,
535 struct ktermios *new,
536 const struct ktermios *old)
537 {
538 unsigned int baud;
539 unsigned int divisor;
540
541 /*
542 * The "MPC5121e Microcontroller Reference Manual, Rev. 3" says on
543 * pg. 30-10 that the chip supports a /32 and a /10 prescaler.
544 * Furthermore, it states that "After reset, the prescaler by 10
545 * for the UART mode is selected", but the reset register value is
546 * 0x0000 which means a /32 prescaler. This is wrong.
547 *
548 * In reality using /32 prescaler doesn't work, as it is not supported!
549 * Use /16 or /10 prescaler, see "MPC5121e Hardware Design Guide",
550 * Chapter 4.1 PSC in UART Mode.
551 * Calculate with a /16 prescaler here.
552 */
553
554 /* uartclk contains the ips freq */
555 baud = uart_get_baud_rate(port, new, old,
556 port->uartclk / (16 * 0xffff) + 1,
557 port->uartclk / 16);
558 divisor = (port->uartclk + 8 * baud) / (16 * baud);
559
560 /* enable the /16 prescaler and set the divisor */
561 mpc52xx_set_divisor(PSC(port), 0xdd00, divisor);
562 return baud;
563 }
564
565 /* Init PSC FIFO Controller */
mpc512x_psc_fifoc_init(void)566 static int __init mpc512x_psc_fifoc_init(void)
567 {
568 int err;
569 struct device_node *np;
570 struct clk *clk;
571
572 /* default error code, potentially overwritten by clock calls */
573 err = -ENODEV;
574
575 np = of_find_compatible_node(NULL, NULL,
576 "fsl,mpc5121-psc-fifo");
577 if (!np) {
578 pr_err("%s: Can't find FIFOC node\n", __func__);
579 goto out_err;
580 }
581
582 clk = of_clk_get(np, 0);
583 if (IS_ERR(clk)) {
584 /* backwards compat with device trees that lack clock specs */
585 clk = clk_get_sys(np->name, "ipg");
586 }
587 if (IS_ERR(clk)) {
588 pr_err("%s: Can't lookup FIFO clock\n", __func__);
589 err = PTR_ERR(clk);
590 goto out_ofnode_put;
591 }
592 if (clk_prepare_enable(clk)) {
593 pr_err("%s: Can't enable FIFO clock\n", __func__);
594 clk_put(clk);
595 goto out_ofnode_put;
596 }
597 psc_fifoc_clk = clk;
598
599 psc_fifoc = of_iomap(np, 0);
600 if (!psc_fifoc) {
601 pr_err("%s: Can't map FIFOC\n", __func__);
602 goto out_clk_disable;
603 }
604
605 psc_fifoc_irq = irq_of_parse_and_map(np, 0);
606 if (psc_fifoc_irq == 0) {
607 pr_err("%s: Can't get FIFOC irq\n", __func__);
608 goto out_unmap;
609 }
610
611 of_node_put(np);
612 return 0;
613
614 out_unmap:
615 iounmap(psc_fifoc);
616 out_clk_disable:
617 clk_disable_unprepare(psc_fifoc_clk);
618 clk_put(psc_fifoc_clk);
619 out_ofnode_put:
620 of_node_put(np);
621 out_err:
622 return err;
623 }
624
mpc512x_psc_fifoc_uninit(void)625 static void __exit mpc512x_psc_fifoc_uninit(void)
626 {
627 iounmap(psc_fifoc);
628
629 /* disable the clock, errors are not fatal */
630 if (psc_fifoc_clk) {
631 clk_disable_unprepare(psc_fifoc_clk);
632 clk_put(psc_fifoc_clk);
633 psc_fifoc_clk = NULL;
634 }
635 }
636
637 static struct clk *psc_mclk_clk[MPC52xx_PSC_MAXNUM];
638 static struct clk *psc_ipg_clk[MPC52xx_PSC_MAXNUM];
639
640 /* 512x specific interrupt handler. The caller holds the port lock */
mpc512x_psc_handle_irq(struct uart_port * port)641 static irqreturn_t mpc512x_psc_handle_irq(struct uart_port *port)
642 {
643 unsigned long fifoc_int;
644 int psc_num;
645
646 /* Read pending PSC FIFOC interrupts */
647 fifoc_int = in_be32(&psc_fifoc->fifoc_int);
648
649 /* Check if it is an interrupt for this port */
650 psc_num = (port->mapbase & 0xf00) >> 8;
651 if (psc_num >= ARRAY_SIZE(psc_mclk_clk))
652 return IRQ_NONE;
653 if (test_bit(psc_num, &fifoc_int) ||
654 test_bit(psc_num + 16, &fifoc_int))
655 return mpc5xxx_uart_process_int(port);
656
657 return IRQ_NONE;
658 }
659
660 /* called from within the .request_port() callback (allocation) */
mpc512x_psc_alloc_clock(struct uart_port * port)661 static int mpc512x_psc_alloc_clock(struct uart_port *port)
662 {
663 int psc_num;
664 struct clk *clk;
665 int err;
666
667 psc_num = (port->mapbase & 0xf00) >> 8;
668 if (psc_num >= ARRAY_SIZE(psc_mclk_clk))
669 return -EINVAL;
670
671 clk = devm_clk_get(port->dev, "mclk");
672 if (IS_ERR(clk)) {
673 dev_err(port->dev, "Failed to get MCLK!\n");
674 err = PTR_ERR(clk);
675 goto out_err;
676 }
677 err = clk_prepare_enable(clk);
678 if (err) {
679 dev_err(port->dev, "Failed to enable MCLK!\n");
680 goto out_err;
681 }
682 psc_mclk_clk[psc_num] = clk;
683
684 clk = devm_clk_get(port->dev, "ipg");
685 if (IS_ERR(clk)) {
686 dev_err(port->dev, "Failed to get IPG clock!\n");
687 err = PTR_ERR(clk);
688 goto out_err;
689 }
690 err = clk_prepare_enable(clk);
691 if (err) {
692 dev_err(port->dev, "Failed to enable IPG clock!\n");
693 goto out_err;
694 }
695 psc_ipg_clk[psc_num] = clk;
696
697 return 0;
698
699 out_err:
700 if (psc_mclk_clk[psc_num]) {
701 clk_disable_unprepare(psc_mclk_clk[psc_num]);
702 psc_mclk_clk[psc_num] = NULL;
703 }
704 if (psc_ipg_clk[psc_num]) {
705 clk_disable_unprepare(psc_ipg_clk[psc_num]);
706 psc_ipg_clk[psc_num] = NULL;
707 }
708 return err;
709 }
710
711 /* called from within the .release_port() callback (release) */
mpc512x_psc_relse_clock(struct uart_port * port)712 static void mpc512x_psc_relse_clock(struct uart_port *port)
713 {
714 int psc_num;
715 struct clk *clk;
716
717 psc_num = (port->mapbase & 0xf00) >> 8;
718 if (psc_num >= ARRAY_SIZE(psc_mclk_clk))
719 return;
720 clk = psc_mclk_clk[psc_num];
721 if (clk) {
722 clk_disable_unprepare(clk);
723 psc_mclk_clk[psc_num] = NULL;
724 }
725 if (psc_ipg_clk[psc_num]) {
726 clk_disable_unprepare(psc_ipg_clk[psc_num]);
727 psc_ipg_clk[psc_num] = NULL;
728 }
729 }
730
731 /* implementation of the .clock() callback (enable/disable) */
mpc512x_psc_endis_clock(struct uart_port * port,int enable)732 static int mpc512x_psc_endis_clock(struct uart_port *port, int enable)
733 {
734 int psc_num;
735 struct clk *psc_clk;
736 int ret;
737
738 if (uart_console(port))
739 return 0;
740
741 psc_num = (port->mapbase & 0xf00) >> 8;
742 if (psc_num >= ARRAY_SIZE(psc_mclk_clk))
743 return -ENODEV;
744 psc_clk = psc_mclk_clk[psc_num];
745 if (!psc_clk) {
746 dev_err(port->dev, "Failed to get PSC clock entry!\n");
747 return -ENODEV;
748 }
749
750 dev_dbg(port->dev, "mclk %sable\n", enable ? "en" : "dis");
751 if (enable) {
752 ret = clk_enable(psc_clk);
753 if (ret)
754 dev_err(port->dev, "Failed to enable MCLK!\n");
755 return ret;
756 } else {
757 clk_disable(psc_clk);
758 return 0;
759 }
760 }
761
mpc512x_psc_get_irq(struct uart_port * port,struct device_node * np)762 static void mpc512x_psc_get_irq(struct uart_port *port, struct device_node *np)
763 {
764 port->irqflags = IRQF_SHARED;
765 port->irq = psc_fifoc_irq;
766 }
767
768 #define PSC_5125(port) ((struct mpc5125_psc __iomem *)((port)->membase))
769 #define FIFO_5125(port) ((struct mpc512x_psc_fifo __iomem *)(PSC_5125(port)+1))
770
mpc5125_psc_fifo_init(struct uart_port * port)771 static void mpc5125_psc_fifo_init(struct uart_port *port)
772 {
773 /* /32 prescaler */
774 out_8(&PSC_5125(port)->mpc52xx_psc_clock_select, 0xdd);
775
776 out_be32(&FIFO_5125(port)->txcmd, MPC512x_PSC_FIFO_RESET_SLICE);
777 out_be32(&FIFO_5125(port)->txcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
778 out_be32(&FIFO_5125(port)->txalarm, 1);
779 out_be32(&FIFO_5125(port)->tximr, 0);
780
781 out_be32(&FIFO_5125(port)->rxcmd, MPC512x_PSC_FIFO_RESET_SLICE);
782 out_be32(&FIFO_5125(port)->rxcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
783 out_be32(&FIFO_5125(port)->rxalarm, 1);
784 out_be32(&FIFO_5125(port)->rximr, 0);
785
786 out_be32(&FIFO_5125(port)->tximr, MPC512x_PSC_FIFO_ALARM);
787 out_be32(&FIFO_5125(port)->rximr, MPC512x_PSC_FIFO_ALARM);
788 }
789
mpc5125_psc_raw_rx_rdy(struct uart_port * port)790 static unsigned int mpc5125_psc_raw_rx_rdy(struct uart_port *port)
791 {
792 return !(in_be32(&FIFO_5125(port)->rxsr) & MPC512x_PSC_FIFO_EMPTY);
793 }
794
mpc5125_psc_raw_tx_rdy(struct uart_port * port)795 static unsigned int mpc5125_psc_raw_tx_rdy(struct uart_port *port)
796 {
797 return !(in_be32(&FIFO_5125(port)->txsr) & MPC512x_PSC_FIFO_FULL);
798 }
799
mpc5125_psc_rx_rdy(struct uart_port * port)800 static unsigned int mpc5125_psc_rx_rdy(struct uart_port *port)
801 {
802 return in_be32(&FIFO_5125(port)->rxsr) &
803 in_be32(&FIFO_5125(port)->rximr) & MPC512x_PSC_FIFO_ALARM;
804 }
805
mpc5125_psc_tx_rdy(struct uart_port * port)806 static unsigned int mpc5125_psc_tx_rdy(struct uart_port *port)
807 {
808 return in_be32(&FIFO_5125(port)->txsr) &
809 in_be32(&FIFO_5125(port)->tximr) & MPC512x_PSC_FIFO_ALARM;
810 }
811
mpc5125_psc_tx_empty(struct uart_port * port)812 static unsigned int mpc5125_psc_tx_empty(struct uart_port *port)
813 {
814 return in_be32(&FIFO_5125(port)->txsr) & MPC512x_PSC_FIFO_EMPTY;
815 }
816
mpc5125_psc_stop_rx(struct uart_port * port)817 static void mpc5125_psc_stop_rx(struct uart_port *port)
818 {
819 unsigned long rx_fifo_imr;
820
821 rx_fifo_imr = in_be32(&FIFO_5125(port)->rximr);
822 rx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
823 out_be32(&FIFO_5125(port)->rximr, rx_fifo_imr);
824 }
825
mpc5125_psc_start_tx(struct uart_port * port)826 static void mpc5125_psc_start_tx(struct uart_port *port)
827 {
828 unsigned long tx_fifo_imr;
829
830 tx_fifo_imr = in_be32(&FIFO_5125(port)->tximr);
831 tx_fifo_imr |= MPC512x_PSC_FIFO_ALARM;
832 out_be32(&FIFO_5125(port)->tximr, tx_fifo_imr);
833 }
834
mpc5125_psc_stop_tx(struct uart_port * port)835 static void mpc5125_psc_stop_tx(struct uart_port *port)
836 {
837 unsigned long tx_fifo_imr;
838
839 tx_fifo_imr = in_be32(&FIFO_5125(port)->tximr);
840 tx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
841 out_be32(&FIFO_5125(port)->tximr, tx_fifo_imr);
842 }
843
mpc5125_psc_rx_clr_irq(struct uart_port * port)844 static void mpc5125_psc_rx_clr_irq(struct uart_port *port)
845 {
846 out_be32(&FIFO_5125(port)->rxisr, in_be32(&FIFO_5125(port)->rxisr));
847 }
848
mpc5125_psc_tx_clr_irq(struct uart_port * port)849 static void mpc5125_psc_tx_clr_irq(struct uart_port *port)
850 {
851 out_be32(&FIFO_5125(port)->txisr, in_be32(&FIFO_5125(port)->txisr));
852 }
853
mpc5125_psc_write_char(struct uart_port * port,unsigned char c)854 static void mpc5125_psc_write_char(struct uart_port *port, unsigned char c)
855 {
856 out_8(&FIFO_5125(port)->txdata_8, c);
857 }
858
mpc5125_psc_read_char(struct uart_port * port)859 static unsigned char mpc5125_psc_read_char(struct uart_port *port)
860 {
861 return in_8(&FIFO_5125(port)->rxdata_8);
862 }
863
mpc5125_psc_cw_disable_ints(struct uart_port * port)864 static void mpc5125_psc_cw_disable_ints(struct uart_port *port)
865 {
866 port->read_status_mask =
867 in_be32(&FIFO_5125(port)->tximr) << 16 |
868 in_be32(&FIFO_5125(port)->rximr);
869 out_be32(&FIFO_5125(port)->tximr, 0);
870 out_be32(&FIFO_5125(port)->rximr, 0);
871 }
872
mpc5125_psc_cw_restore_ints(struct uart_port * port)873 static void mpc5125_psc_cw_restore_ints(struct uart_port *port)
874 {
875 out_be32(&FIFO_5125(port)->tximr,
876 (port->read_status_mask >> 16) & 0x7f);
877 out_be32(&FIFO_5125(port)->rximr, port->read_status_mask & 0x7f);
878 }
879
mpc5125_set_divisor(struct mpc5125_psc __iomem * psc,u8 prescaler,unsigned int divisor)880 static inline void mpc5125_set_divisor(struct mpc5125_psc __iomem *psc,
881 u8 prescaler, unsigned int divisor)
882 {
883 /* select prescaler */
884 out_8(&psc->mpc52xx_psc_clock_select, prescaler);
885 out_8(&psc->ctur, divisor >> 8);
886 out_8(&psc->ctlr, divisor & 0xff);
887 }
888
mpc5125_psc_set_baudrate(struct uart_port * port,struct ktermios * new,const struct ktermios * old)889 static unsigned int mpc5125_psc_set_baudrate(struct uart_port *port,
890 struct ktermios *new,
891 const struct ktermios *old)
892 {
893 unsigned int baud;
894 unsigned int divisor;
895
896 /*
897 * Calculate with a /16 prescaler here.
898 */
899
900 /* uartclk contains the ips freq */
901 baud = uart_get_baud_rate(port, new, old,
902 port->uartclk / (16 * 0xffff) + 1,
903 port->uartclk / 16);
904 divisor = (port->uartclk + 8 * baud) / (16 * baud);
905
906 /* enable the /16 prescaler and set the divisor */
907 mpc5125_set_divisor(PSC_5125(port), 0xdd, divisor);
908 return baud;
909 }
910
911 /*
912 * MPC5125 have compatible PSC FIFO Controller.
913 * Special init not needed.
914 */
mpc5125_psc_get_status(struct uart_port * port)915 static u16 mpc5125_psc_get_status(struct uart_port *port)
916 {
917 return in_be16(&PSC_5125(port)->mpc52xx_psc_status);
918 }
919
mpc5125_psc_get_ipcr(struct uart_port * port)920 static u8 mpc5125_psc_get_ipcr(struct uart_port *port)
921 {
922 return in_8(&PSC_5125(port)->mpc52xx_psc_ipcr);
923 }
924
mpc5125_psc_command(struct uart_port * port,u8 cmd)925 static void mpc5125_psc_command(struct uart_port *port, u8 cmd)
926 {
927 out_8(&PSC_5125(port)->command, cmd);
928 }
929
mpc5125_psc_set_mode(struct uart_port * port,u8 mr1,u8 mr2)930 static void mpc5125_psc_set_mode(struct uart_port *port, u8 mr1, u8 mr2)
931 {
932 out_8(&PSC_5125(port)->mr1, mr1);
933 out_8(&PSC_5125(port)->mr2, mr2);
934 }
935
mpc5125_psc_set_rts(struct uart_port * port,int state)936 static void mpc5125_psc_set_rts(struct uart_port *port, int state)
937 {
938 if (state & TIOCM_RTS)
939 out_8(&PSC_5125(port)->op1, MPC52xx_PSC_OP_RTS);
940 else
941 out_8(&PSC_5125(port)->op0, MPC52xx_PSC_OP_RTS);
942 }
943
mpc5125_psc_enable_ms(struct uart_port * port)944 static void mpc5125_psc_enable_ms(struct uart_port *port)
945 {
946 struct mpc5125_psc __iomem *psc = PSC_5125(port);
947
948 /* clear D_*-bits by reading them */
949 in_8(&psc->mpc52xx_psc_ipcr);
950 /* enable CTS and DCD as IPC interrupts */
951 out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
952
953 port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
954 out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
955 }
956
mpc5125_psc_set_sicr(struct uart_port * port,u32 val)957 static void mpc5125_psc_set_sicr(struct uart_port *port, u32 val)
958 {
959 out_be32(&PSC_5125(port)->sicr, val);
960 }
961
mpc5125_psc_set_imr(struct uart_port * port,u16 val)962 static void mpc5125_psc_set_imr(struct uart_port *port, u16 val)
963 {
964 out_be16(&PSC_5125(port)->mpc52xx_psc_imr, val);
965 }
966
mpc5125_psc_get_mr1(struct uart_port * port)967 static u8 mpc5125_psc_get_mr1(struct uart_port *port)
968 {
969 return in_8(&PSC_5125(port)->mr1);
970 }
971
972 static const struct psc_ops mpc5125_psc_ops = {
973 .fifo_init = mpc5125_psc_fifo_init,
974 .raw_rx_rdy = mpc5125_psc_raw_rx_rdy,
975 .raw_tx_rdy = mpc5125_psc_raw_tx_rdy,
976 .rx_rdy = mpc5125_psc_rx_rdy,
977 .tx_rdy = mpc5125_psc_tx_rdy,
978 .tx_empty = mpc5125_psc_tx_empty,
979 .stop_rx = mpc5125_psc_stop_rx,
980 .start_tx = mpc5125_psc_start_tx,
981 .stop_tx = mpc5125_psc_stop_tx,
982 .rx_clr_irq = mpc5125_psc_rx_clr_irq,
983 .tx_clr_irq = mpc5125_psc_tx_clr_irq,
984 .write_char = mpc5125_psc_write_char,
985 .read_char = mpc5125_psc_read_char,
986 .cw_disable_ints = mpc5125_psc_cw_disable_ints,
987 .cw_restore_ints = mpc5125_psc_cw_restore_ints,
988 .set_baudrate = mpc5125_psc_set_baudrate,
989 .clock_alloc = mpc512x_psc_alloc_clock,
990 .clock_relse = mpc512x_psc_relse_clock,
991 .clock = mpc512x_psc_endis_clock,
992 .fifoc_init = mpc512x_psc_fifoc_init,
993 .fifoc_uninit = mpc512x_psc_fifoc_uninit,
994 .get_irq = mpc512x_psc_get_irq,
995 .handle_irq = mpc512x_psc_handle_irq,
996 .get_status = mpc5125_psc_get_status,
997 .get_ipcr = mpc5125_psc_get_ipcr,
998 .command = mpc5125_psc_command,
999 .set_mode = mpc5125_psc_set_mode,
1000 .set_rts = mpc5125_psc_set_rts,
1001 .enable_ms = mpc5125_psc_enable_ms,
1002 .set_sicr = mpc5125_psc_set_sicr,
1003 .set_imr = mpc5125_psc_set_imr,
1004 .get_mr1 = mpc5125_psc_get_mr1,
1005 };
1006
1007 static const struct psc_ops mpc512x_psc_ops = {
1008 .fifo_init = mpc512x_psc_fifo_init,
1009 .raw_rx_rdy = mpc512x_psc_raw_rx_rdy,
1010 .raw_tx_rdy = mpc512x_psc_raw_tx_rdy,
1011 .rx_rdy = mpc512x_psc_rx_rdy,
1012 .tx_rdy = mpc512x_psc_tx_rdy,
1013 .tx_empty = mpc512x_psc_tx_empty,
1014 .stop_rx = mpc512x_psc_stop_rx,
1015 .start_tx = mpc512x_psc_start_tx,
1016 .stop_tx = mpc512x_psc_stop_tx,
1017 .rx_clr_irq = mpc512x_psc_rx_clr_irq,
1018 .tx_clr_irq = mpc512x_psc_tx_clr_irq,
1019 .write_char = mpc512x_psc_write_char,
1020 .read_char = mpc512x_psc_read_char,
1021 .cw_disable_ints = mpc512x_psc_cw_disable_ints,
1022 .cw_restore_ints = mpc512x_psc_cw_restore_ints,
1023 .set_baudrate = mpc512x_psc_set_baudrate,
1024 .clock_alloc = mpc512x_psc_alloc_clock,
1025 .clock_relse = mpc512x_psc_relse_clock,
1026 .clock = mpc512x_psc_endis_clock,
1027 .fifoc_init = mpc512x_psc_fifoc_init,
1028 .fifoc_uninit = mpc512x_psc_fifoc_uninit,
1029 .get_irq = mpc512x_psc_get_irq,
1030 .handle_irq = mpc512x_psc_handle_irq,
1031 .get_status = mpc52xx_psc_get_status,
1032 .get_ipcr = mpc52xx_psc_get_ipcr,
1033 .command = mpc52xx_psc_command,
1034 .set_mode = mpc52xx_psc_set_mode,
1035 .set_rts = mpc52xx_psc_set_rts,
1036 .enable_ms = mpc52xx_psc_enable_ms,
1037 .set_sicr = mpc52xx_psc_set_sicr,
1038 .set_imr = mpc52xx_psc_set_imr,
1039 .get_mr1 = mpc52xx_psc_get_mr1,
1040 };
1041 #endif /* CONFIG_PPC_MPC512x */
1042
1043
1044 static const struct psc_ops *psc_ops;
1045
1046 /* ======================================================================== */
1047 /* UART operations */
1048 /* ======================================================================== */
1049
1050 static unsigned int
mpc52xx_uart_tx_empty(struct uart_port * port)1051 mpc52xx_uart_tx_empty(struct uart_port *port)
1052 {
1053 return psc_ops->tx_empty(port) ? TIOCSER_TEMT : 0;
1054 }
1055
1056 static void
mpc52xx_uart_set_mctrl(struct uart_port * port,unsigned int mctrl)1057 mpc52xx_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
1058 {
1059 psc_ops->set_rts(port, mctrl & TIOCM_RTS);
1060 }
1061
1062 static unsigned int
mpc52xx_uart_get_mctrl(struct uart_port * port)1063 mpc52xx_uart_get_mctrl(struct uart_port *port)
1064 {
1065 unsigned int ret = TIOCM_DSR;
1066 u8 status = psc_ops->get_ipcr(port);
1067
1068 if (!(status & MPC52xx_PSC_CTS))
1069 ret |= TIOCM_CTS;
1070 if (!(status & MPC52xx_PSC_DCD))
1071 ret |= TIOCM_CAR;
1072
1073 return ret;
1074 }
1075
1076 static void
mpc52xx_uart_stop_tx(struct uart_port * port)1077 mpc52xx_uart_stop_tx(struct uart_port *port)
1078 {
1079 /* port->lock taken by caller */
1080 psc_ops->stop_tx(port);
1081 }
1082
1083 static void
mpc52xx_uart_start_tx(struct uart_port * port)1084 mpc52xx_uart_start_tx(struct uart_port *port)
1085 {
1086 /* port->lock taken by caller */
1087 psc_ops->start_tx(port);
1088 }
1089
1090 static void
mpc52xx_uart_stop_rx(struct uart_port * port)1091 mpc52xx_uart_stop_rx(struct uart_port *port)
1092 {
1093 /* port->lock taken by caller */
1094 psc_ops->stop_rx(port);
1095 }
1096
1097 static void
mpc52xx_uart_enable_ms(struct uart_port * port)1098 mpc52xx_uart_enable_ms(struct uart_port *port)
1099 {
1100 psc_ops->enable_ms(port);
1101 }
1102
1103 static void
mpc52xx_uart_break_ctl(struct uart_port * port,int ctl)1104 mpc52xx_uart_break_ctl(struct uart_port *port, int ctl)
1105 {
1106 unsigned long flags;
1107 uart_port_lock_irqsave(port, &flags);
1108
1109 if (ctl == -1)
1110 psc_ops->command(port, MPC52xx_PSC_START_BRK);
1111 else
1112 psc_ops->command(port, MPC52xx_PSC_STOP_BRK);
1113
1114 uart_port_unlock_irqrestore(port, flags);
1115 }
1116
1117 static int
mpc52xx_uart_startup(struct uart_port * port)1118 mpc52xx_uart_startup(struct uart_port *port)
1119 {
1120 int ret;
1121
1122 if (psc_ops->clock) {
1123 ret = psc_ops->clock(port, 1);
1124 if (ret)
1125 return ret;
1126 }
1127
1128 /* Request IRQ */
1129 ret = request_irq(port->irq, mpc52xx_uart_int,
1130 port->irqflags, "mpc52xx_psc_uart", port);
1131 if (ret)
1132 return ret;
1133
1134 /* Reset/activate the port, clear and enable interrupts */
1135 psc_ops->command(port, MPC52xx_PSC_RST_RX);
1136 psc_ops->command(port, MPC52xx_PSC_RST_TX);
1137
1138 /*
1139 * According to Freescale's support the RST_TX command can produce a
1140 * spike on the TX pin. So they recommend to delay "for one character".
1141 * One millisecond should be enough for everyone.
1142 */
1143 msleep(1);
1144
1145 psc_ops->set_sicr(port, 0); /* UART mode DCD ignored */
1146
1147 psc_ops->fifo_init(port);
1148
1149 psc_ops->command(port, MPC52xx_PSC_TX_ENABLE);
1150 psc_ops->command(port, MPC52xx_PSC_RX_ENABLE);
1151
1152 return 0;
1153 }
1154
1155 static void
mpc52xx_uart_shutdown(struct uart_port * port)1156 mpc52xx_uart_shutdown(struct uart_port *port)
1157 {
1158 /* Shut down the port. Leave TX active if on a console port */
1159 psc_ops->command(port, MPC52xx_PSC_RST_RX);
1160 if (!uart_console(port))
1161 psc_ops->command(port, MPC52xx_PSC_RST_TX);
1162
1163 port->read_status_mask = 0;
1164 psc_ops->set_imr(port, port->read_status_mask);
1165
1166 if (psc_ops->clock)
1167 psc_ops->clock(port, 0);
1168
1169 /* Disable interrupt */
1170 psc_ops->cw_disable_ints(port);
1171
1172 /* Release interrupt */
1173 free_irq(port->irq, port);
1174 }
1175
1176 static void
mpc52xx_uart_set_termios(struct uart_port * port,struct ktermios * new,const struct ktermios * old)1177 mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
1178 const struct ktermios *old)
1179 {
1180 unsigned long flags;
1181 unsigned char mr1, mr2;
1182 unsigned int j;
1183 unsigned int baud;
1184
1185 /* Prepare what we're gonna write */
1186 mr1 = 0;
1187
1188 switch (new->c_cflag & CSIZE) {
1189 case CS5: mr1 |= MPC52xx_PSC_MODE_5_BITS;
1190 break;
1191 case CS6: mr1 |= MPC52xx_PSC_MODE_6_BITS;
1192 break;
1193 case CS7: mr1 |= MPC52xx_PSC_MODE_7_BITS;
1194 break;
1195 case CS8:
1196 default: mr1 |= MPC52xx_PSC_MODE_8_BITS;
1197 }
1198
1199 if (new->c_cflag & PARENB) {
1200 if (new->c_cflag & CMSPAR)
1201 mr1 |= MPC52xx_PSC_MODE_PARFORCE;
1202
1203 /* With CMSPAR, PARODD also means high parity (same as termios) */
1204 mr1 |= (new->c_cflag & PARODD) ?
1205 MPC52xx_PSC_MODE_PARODD : MPC52xx_PSC_MODE_PAREVEN;
1206 } else {
1207 mr1 |= MPC52xx_PSC_MODE_PARNONE;
1208 }
1209
1210 mr2 = 0;
1211
1212 if (new->c_cflag & CSTOPB)
1213 mr2 |= MPC52xx_PSC_MODE_TWO_STOP;
1214 else
1215 mr2 |= ((new->c_cflag & CSIZE) == CS5) ?
1216 MPC52xx_PSC_MODE_ONE_STOP_5_BITS :
1217 MPC52xx_PSC_MODE_ONE_STOP;
1218
1219 if (new->c_cflag & CRTSCTS) {
1220 mr1 |= MPC52xx_PSC_MODE_RXRTS;
1221 mr2 |= MPC52xx_PSC_MODE_TXCTS;
1222 }
1223
1224 /* Get the lock */
1225 uart_port_lock_irqsave(port, &flags);
1226
1227 /* Do our best to flush TX & RX, so we don't lose anything */
1228 /* But we don't wait indefinitely ! */
1229 j = 5000000; /* Maximum wait */
1230 /* FIXME Can't receive chars since set_termios might be called at early
1231 * boot for the console, all stuff is not yet ready to receive at that
1232 * time and that just makes the kernel oops */
1233 /* while (j-- && mpc52xx_uart_int_rx_chars(port)); */
1234 while (!mpc52xx_uart_tx_empty(port) && --j)
1235 udelay(1);
1236
1237 if (!j)
1238 printk(KERN_ERR "mpc52xx_uart.c: "
1239 "Unable to flush RX & TX fifos in-time in set_termios."
1240 "Some chars may have been lost.\n");
1241
1242 /* Reset the TX & RX */
1243 psc_ops->command(port, MPC52xx_PSC_RST_RX);
1244 psc_ops->command(port, MPC52xx_PSC_RST_TX);
1245
1246 /* Send new mode settings */
1247 psc_ops->set_mode(port, mr1, mr2);
1248 baud = psc_ops->set_baudrate(port, new, old);
1249
1250 /* Update the per-port timeout */
1251 uart_update_timeout(port, new->c_cflag, baud);
1252
1253 if (UART_ENABLE_MS(port, new->c_cflag))
1254 mpc52xx_uart_enable_ms(port);
1255
1256 /* Reenable TX & RX */
1257 psc_ops->command(port, MPC52xx_PSC_TX_ENABLE);
1258 psc_ops->command(port, MPC52xx_PSC_RX_ENABLE);
1259
1260 /* We're all set, release the lock */
1261 uart_port_unlock_irqrestore(port, flags);
1262 }
1263
1264 static const char *
mpc52xx_uart_type(struct uart_port * port)1265 mpc52xx_uart_type(struct uart_port *port)
1266 {
1267 /*
1268 * We keep using PORT_MPC52xx for historic reasons although it applies
1269 * for MPC512x, too, but print "MPC5xxx" to not irritate users
1270 */
1271 return port->type == PORT_MPC52xx ? "MPC5xxx PSC" : NULL;
1272 }
1273
1274 static void
mpc52xx_uart_release_port(struct uart_port * port)1275 mpc52xx_uart_release_port(struct uart_port *port)
1276 {
1277 if (psc_ops->clock_relse)
1278 psc_ops->clock_relse(port);
1279
1280 /* remapped by us ? */
1281 if (port->flags & UPF_IOREMAP) {
1282 iounmap(port->membase);
1283 port->membase = NULL;
1284 }
1285
1286 release_mem_region(port->mapbase, sizeof(struct mpc52xx_psc));
1287 }
1288
1289 static int
mpc52xx_uart_request_port(struct uart_port * port)1290 mpc52xx_uart_request_port(struct uart_port *port)
1291 {
1292 int err;
1293
1294 if (port->flags & UPF_IOREMAP) /* Need to remap ? */
1295 port->membase = ioremap(port->mapbase,
1296 sizeof(struct mpc52xx_psc));
1297
1298 if (!port->membase)
1299 return -EINVAL;
1300
1301 err = request_mem_region(port->mapbase, sizeof(struct mpc52xx_psc),
1302 "mpc52xx_psc_uart") != NULL ? 0 : -EBUSY;
1303
1304 if (err)
1305 goto out_membase;
1306
1307 if (psc_ops->clock_alloc) {
1308 err = psc_ops->clock_alloc(port);
1309 if (err)
1310 goto out_mapregion;
1311 }
1312
1313 return 0;
1314
1315 out_mapregion:
1316 release_mem_region(port->mapbase, sizeof(struct mpc52xx_psc));
1317 out_membase:
1318 if (port->flags & UPF_IOREMAP) {
1319 iounmap(port->membase);
1320 port->membase = NULL;
1321 }
1322 return err;
1323 }
1324
1325 static void
mpc52xx_uart_config_port(struct uart_port * port,int flags)1326 mpc52xx_uart_config_port(struct uart_port *port, int flags)
1327 {
1328 if ((flags & UART_CONFIG_TYPE)
1329 && (mpc52xx_uart_request_port(port) == 0))
1330 port->type = PORT_MPC52xx;
1331 }
1332
1333 static int
mpc52xx_uart_verify_port(struct uart_port * port,struct serial_struct * ser)1334 mpc52xx_uart_verify_port(struct uart_port *port, struct serial_struct *ser)
1335 {
1336 if (ser->type != PORT_UNKNOWN && ser->type != PORT_MPC52xx)
1337 return -EINVAL;
1338
1339 if ((ser->irq != port->irq) ||
1340 (ser->io_type != UPIO_MEM) ||
1341 (ser->baud_base != port->uartclk) ||
1342 (ser->iomem_base != (void *)port->mapbase) ||
1343 (ser->hub6 != 0))
1344 return -EINVAL;
1345
1346 return 0;
1347 }
1348
1349
1350 static const struct uart_ops mpc52xx_uart_ops = {
1351 .tx_empty = mpc52xx_uart_tx_empty,
1352 .set_mctrl = mpc52xx_uart_set_mctrl,
1353 .get_mctrl = mpc52xx_uart_get_mctrl,
1354 .stop_tx = mpc52xx_uart_stop_tx,
1355 .start_tx = mpc52xx_uart_start_tx,
1356 .stop_rx = mpc52xx_uart_stop_rx,
1357 .enable_ms = mpc52xx_uart_enable_ms,
1358 .break_ctl = mpc52xx_uart_break_ctl,
1359 .startup = mpc52xx_uart_startup,
1360 .shutdown = mpc52xx_uart_shutdown,
1361 .set_termios = mpc52xx_uart_set_termios,
1362 .type = mpc52xx_uart_type,
1363 .release_port = mpc52xx_uart_release_port,
1364 .request_port = mpc52xx_uart_request_port,
1365 .config_port = mpc52xx_uart_config_port,
1366 .verify_port = mpc52xx_uart_verify_port
1367 };
1368
1369
1370 /* ======================================================================== */
1371 /* Interrupt handling */
1372 /* ======================================================================== */
1373
1374 static inline bool
mpc52xx_uart_int_rx_chars(struct uart_port * port)1375 mpc52xx_uart_int_rx_chars(struct uart_port *port)
1376 {
1377 struct tty_port *tport = &port->state->port;
1378 unsigned char ch, flag;
1379 unsigned short status;
1380
1381 /* While we can read, do so ! */
1382 while (psc_ops->raw_rx_rdy(port)) {
1383 /* Get the char */
1384 ch = psc_ops->read_char(port);
1385
1386 /* Handle sysreq char */
1387 if (uart_handle_sysrq_char(port, ch))
1388 continue;
1389
1390 /* Store it */
1391
1392 flag = TTY_NORMAL;
1393 port->icount.rx++;
1394
1395 status = psc_ops->get_status(port);
1396
1397 if (status & (MPC52xx_PSC_SR_PE |
1398 MPC52xx_PSC_SR_FE |
1399 MPC52xx_PSC_SR_RB)) {
1400
1401 if (status & MPC52xx_PSC_SR_RB) {
1402 flag = TTY_BREAK;
1403 uart_handle_break(port);
1404 port->icount.brk++;
1405 } else if (status & MPC52xx_PSC_SR_PE) {
1406 flag = TTY_PARITY;
1407 port->icount.parity++;
1408 }
1409 else if (status & MPC52xx_PSC_SR_FE) {
1410 flag = TTY_FRAME;
1411 port->icount.frame++;
1412 }
1413
1414 /* Clear error condition */
1415 psc_ops->command(port, MPC52xx_PSC_RST_ERR_STAT);
1416
1417 }
1418 tty_insert_flip_char(tport, ch, flag);
1419 if (status & MPC52xx_PSC_SR_OE) {
1420 /*
1421 * Overrun is special, since it's
1422 * reported immediately, and doesn't
1423 * affect the current character
1424 */
1425 tty_insert_flip_char(tport, 0, TTY_OVERRUN);
1426 port->icount.overrun++;
1427 }
1428 }
1429
1430 tty_flip_buffer_push(tport);
1431
1432 return psc_ops->raw_rx_rdy(port);
1433 }
1434
1435 static inline bool
mpc52xx_uart_int_tx_chars(struct uart_port * port)1436 mpc52xx_uart_int_tx_chars(struct uart_port *port)
1437 {
1438 u8 ch;
1439
1440 return uart_port_tx(port, ch,
1441 psc_ops->raw_tx_rdy(port),
1442 psc_ops->write_char(port, ch));
1443 }
1444
1445 static irqreturn_t
mpc5xxx_uart_process_int(struct uart_port * port)1446 mpc5xxx_uart_process_int(struct uart_port *port)
1447 {
1448 unsigned long pass = ISR_PASS_LIMIT;
1449 bool keepgoing;
1450 u8 status;
1451
1452 /* While we have stuff to do, we continue */
1453 do {
1454 /* If we don't find anything to do, we stop */
1455 keepgoing = false;
1456
1457 psc_ops->rx_clr_irq(port);
1458 if (psc_ops->rx_rdy(port))
1459 keepgoing |= mpc52xx_uart_int_rx_chars(port);
1460
1461 psc_ops->tx_clr_irq(port);
1462 if (psc_ops->tx_rdy(port))
1463 keepgoing |= mpc52xx_uart_int_tx_chars(port);
1464
1465 status = psc_ops->get_ipcr(port);
1466 if (status & MPC52xx_PSC_D_DCD)
1467 uart_handle_dcd_change(port, !(status & MPC52xx_PSC_DCD));
1468
1469 if (status & MPC52xx_PSC_D_CTS)
1470 uart_handle_cts_change(port, !(status & MPC52xx_PSC_CTS));
1471
1472 /* Limit number of iteration */
1473 if (!(--pass))
1474 keepgoing = false;
1475
1476 } while (keepgoing);
1477
1478 return IRQ_HANDLED;
1479 }
1480
1481 static irqreturn_t
mpc52xx_uart_int(int irq,void * dev_id)1482 mpc52xx_uart_int(int irq, void *dev_id)
1483 {
1484 struct uart_port *port = dev_id;
1485 irqreturn_t ret;
1486
1487 uart_port_lock(port);
1488
1489 ret = psc_ops->handle_irq(port);
1490
1491 uart_port_unlock(port);
1492
1493 return ret;
1494 }
1495
1496 /* ======================================================================== */
1497 /* Console ( if applicable ) */
1498 /* ======================================================================== */
1499
1500 #ifdef CONFIG_SERIAL_MPC52xx_CONSOLE
1501
1502 static void __init
mpc52xx_console_get_options(struct uart_port * port,int * baud,int * parity,int * bits,int * flow)1503 mpc52xx_console_get_options(struct uart_port *port,
1504 int *baud, int *parity, int *bits, int *flow)
1505 {
1506 unsigned char mr1;
1507
1508 pr_debug("mpc52xx_console_get_options(port=%p)\n", port);
1509
1510 /* Read the mode registers */
1511 mr1 = psc_ops->get_mr1(port);
1512
1513 /* CT{U,L}R are write-only ! */
1514 *baud = CONFIG_SERIAL_MPC52xx_CONSOLE_BAUD;
1515
1516 /* Parse them */
1517 switch (mr1 & MPC52xx_PSC_MODE_BITS_MASK) {
1518 case MPC52xx_PSC_MODE_5_BITS:
1519 *bits = 5;
1520 break;
1521 case MPC52xx_PSC_MODE_6_BITS:
1522 *bits = 6;
1523 break;
1524 case MPC52xx_PSC_MODE_7_BITS:
1525 *bits = 7;
1526 break;
1527 case MPC52xx_PSC_MODE_8_BITS:
1528 default:
1529 *bits = 8;
1530 }
1531
1532 if (mr1 & MPC52xx_PSC_MODE_PARNONE)
1533 *parity = 'n';
1534 else
1535 *parity = mr1 & MPC52xx_PSC_MODE_PARODD ? 'o' : 'e';
1536 }
1537
1538 static void
mpc52xx_console_write(struct console * co,const char * s,unsigned int count)1539 mpc52xx_console_write(struct console *co, const char *s, unsigned int count)
1540 {
1541 struct uart_port *port = &mpc52xx_uart_ports[co->index];
1542 unsigned int i, j;
1543
1544 /* Disable interrupts */
1545 psc_ops->cw_disable_ints(port);
1546
1547 /* Wait the TX buffer to be empty */
1548 j = 5000000; /* Maximum wait */
1549 while (!mpc52xx_uart_tx_empty(port) && --j)
1550 udelay(1);
1551
1552 /* Write all the chars */
1553 for (i = 0; i < count; i++, s++) {
1554 /* Line return handling */
1555 if (*s == '\n')
1556 psc_ops->write_char(port, '\r');
1557
1558 /* Send the char */
1559 psc_ops->write_char(port, *s);
1560
1561 /* Wait the TX buffer to be empty */
1562 j = 20000; /* Maximum wait */
1563 while (!mpc52xx_uart_tx_empty(port) && --j)
1564 udelay(1);
1565 }
1566
1567 /* Restore interrupt state */
1568 psc_ops->cw_restore_ints(port);
1569 }
1570
1571
1572 static int __init
mpc52xx_console_setup(struct console * co,char * options)1573 mpc52xx_console_setup(struct console *co, char *options)
1574 {
1575 struct uart_port *port = &mpc52xx_uart_ports[co->index];
1576 struct device_node *np = mpc52xx_uart_nodes[co->index];
1577 unsigned int uartclk;
1578 struct resource res;
1579 int ret;
1580
1581 int baud = CONFIG_SERIAL_MPC52xx_CONSOLE_BAUD;
1582 int bits = 8;
1583 int parity = 'n';
1584 int flow = 'n';
1585
1586 pr_debug("mpc52xx_console_setup co=%p, co->index=%i, options=%s\n",
1587 co, co->index, options);
1588
1589 if ((co->index < 0) || (co->index >= MPC52xx_PSC_MAXNUM)) {
1590 pr_debug("PSC%x out of range\n", co->index);
1591 return -EINVAL;
1592 }
1593
1594 if (!np) {
1595 pr_debug("PSC%x not found in device tree\n", co->index);
1596 return -EINVAL;
1597 }
1598
1599 pr_debug("Console on ttyPSC%x is %pOF\n",
1600 co->index, mpc52xx_uart_nodes[co->index]);
1601
1602 /* Fetch register locations */
1603 ret = of_address_to_resource(np, 0, &res);
1604 if (ret) {
1605 pr_debug("Could not get resources for PSC%x\n", co->index);
1606 return ret;
1607 }
1608
1609 uartclk = mpc5xxx_fwnode_get_bus_frequency(of_fwnode_handle(np));
1610 if (uartclk == 0) {
1611 pr_debug("Could not find uart clock frequency!\n");
1612 return -EINVAL;
1613 }
1614
1615 /* Basic port init. Needed since we use some uart_??? func before
1616 * real init for early access */
1617 spin_lock_init(&port->lock);
1618 port->uartclk = uartclk;
1619 port->ops = &mpc52xx_uart_ops;
1620 port->mapbase = res.start;
1621 port->membase = ioremap(res.start, sizeof(struct mpc52xx_psc));
1622 port->irq = irq_of_parse_and_map(np, 0);
1623
1624 if (port->membase == NULL)
1625 return -EINVAL;
1626
1627 pr_debug("mpc52xx-psc uart at %p, mapped to %p, irq=%x, freq=%i\n",
1628 (void *)port->mapbase, port->membase,
1629 port->irq, port->uartclk);
1630
1631 /* Setup the port parameters according to options */
1632 if (options)
1633 uart_parse_options(options, &baud, &parity, &bits, &flow);
1634 else
1635 mpc52xx_console_get_options(port, &baud, &parity, &bits, &flow);
1636
1637 pr_debug("Setting console parameters: %i %i%c1 flow=%c\n",
1638 baud, bits, parity, flow);
1639
1640 return uart_set_options(port, co, baud, parity, bits, flow);
1641 }
1642
1643
1644 static struct uart_driver mpc52xx_uart_driver;
1645
1646 static struct console mpc52xx_console = {
1647 .name = "ttyPSC",
1648 .write = mpc52xx_console_write,
1649 .device = uart_console_device,
1650 .setup = mpc52xx_console_setup,
1651 .flags = CON_PRINTBUFFER,
1652 .index = -1, /* Specified on the cmdline (e.g. console=ttyPSC0) */
1653 .data = &mpc52xx_uart_driver,
1654 };
1655
1656
1657 static int __init
mpc52xx_console_init(void)1658 mpc52xx_console_init(void)
1659 {
1660 mpc52xx_uart_of_enumerate();
1661 register_console(&mpc52xx_console);
1662 return 0;
1663 }
1664
1665 console_initcall(mpc52xx_console_init);
1666
1667 #define MPC52xx_PSC_CONSOLE &mpc52xx_console
1668 #else
1669 #define MPC52xx_PSC_CONSOLE NULL
1670 #endif
1671
1672
1673 /* ======================================================================== */
1674 /* UART Driver */
1675 /* ======================================================================== */
1676
1677 static struct uart_driver mpc52xx_uart_driver = {
1678 .driver_name = "mpc52xx_psc_uart",
1679 .dev_name = "ttyPSC",
1680 .major = SERIAL_PSC_MAJOR,
1681 .minor = SERIAL_PSC_MINOR,
1682 .nr = MPC52xx_PSC_MAXNUM,
1683 .cons = MPC52xx_PSC_CONSOLE,
1684 };
1685
1686 /* ======================================================================== */
1687 /* OF Platform Driver */
1688 /* ======================================================================== */
1689
1690 static const struct of_device_id mpc52xx_uart_of_match[] = {
1691 #ifdef CONFIG_PPC_MPC52xx
1692 { .compatible = "fsl,mpc5200b-psc-uart", .data = &mpc5200b_psc_ops, },
1693 { .compatible = "fsl,mpc5200-psc-uart", .data = &mpc52xx_psc_ops, },
1694 /* binding used by old lite5200 device trees: */
1695 { .compatible = "mpc5200-psc-uart", .data = &mpc52xx_psc_ops, },
1696 /* binding used by efika: */
1697 { .compatible = "mpc5200-serial", .data = &mpc52xx_psc_ops, },
1698 #endif
1699 #ifdef CONFIG_PPC_MPC512x
1700 { .compatible = "fsl,mpc5121-psc-uart", .data = &mpc512x_psc_ops, },
1701 { .compatible = "fsl,mpc5125-psc-uart", .data = &mpc5125_psc_ops, },
1702 #endif
1703 {},
1704 };
1705
mpc52xx_uart_of_probe(struct platform_device * op)1706 static int mpc52xx_uart_of_probe(struct platform_device *op)
1707 {
1708 int idx = -1;
1709 unsigned int uartclk;
1710 struct uart_port *port = NULL;
1711 struct resource res;
1712 int ret;
1713
1714 /* Check validity & presence */
1715 for (idx = 0; idx < MPC52xx_PSC_MAXNUM; idx++)
1716 if (mpc52xx_uart_nodes[idx] == op->dev.of_node)
1717 break;
1718 if (idx >= MPC52xx_PSC_MAXNUM)
1719 return -EINVAL;
1720 pr_debug("Found %pOF assigned to ttyPSC%x\n",
1721 mpc52xx_uart_nodes[idx], idx);
1722
1723 /* set the uart clock to the input clock of the psc, the different
1724 * prescalers are taken into account in the set_baudrate() methods
1725 * of the respective chip */
1726 uartclk = mpc5xxx_get_bus_frequency(&op->dev);
1727 if (uartclk == 0) {
1728 dev_dbg(&op->dev, "Could not find uart clock frequency!\n");
1729 return -EINVAL;
1730 }
1731
1732 /* Init the port structure */
1733 port = &mpc52xx_uart_ports[idx];
1734
1735 spin_lock_init(&port->lock);
1736 port->uartclk = uartclk;
1737 port->fifosize = 512;
1738 port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_MPC52xx_CONSOLE);
1739 port->iotype = UPIO_MEM;
1740 port->flags = UPF_BOOT_AUTOCONF |
1741 (uart_console(port) ? 0 : UPF_IOREMAP);
1742 port->line = idx;
1743 port->ops = &mpc52xx_uart_ops;
1744 port->dev = &op->dev;
1745
1746 /* Search for IRQ and mapbase */
1747 ret = of_address_to_resource(op->dev.of_node, 0, &res);
1748 if (ret)
1749 return ret;
1750
1751 port->mapbase = res.start;
1752 if (!port->mapbase) {
1753 dev_dbg(&op->dev, "Could not allocate resources for PSC\n");
1754 return -EINVAL;
1755 }
1756
1757 psc_ops->get_irq(port, op->dev.of_node);
1758 if (port->irq == 0) {
1759 dev_dbg(&op->dev, "Could not get irq\n");
1760 return -EINVAL;
1761 }
1762
1763 dev_dbg(&op->dev, "mpc52xx-psc uart at %p, irq=%x, freq=%i\n",
1764 (void *)port->mapbase, port->irq, port->uartclk);
1765
1766 /* Add the port to the uart sub-system */
1767 ret = uart_add_one_port(&mpc52xx_uart_driver, port);
1768 if (ret)
1769 return ret;
1770
1771 platform_set_drvdata(op, (void *)port);
1772 return 0;
1773 }
1774
mpc52xx_uart_of_remove(struct platform_device * op)1775 static void mpc52xx_uart_of_remove(struct platform_device *op)
1776 {
1777 struct uart_port *port = platform_get_drvdata(op);
1778
1779 if (port)
1780 uart_remove_one_port(&mpc52xx_uart_driver, port);
1781 }
1782
1783 #ifdef CONFIG_PM
1784 static int
mpc52xx_uart_of_suspend(struct platform_device * op,pm_message_t state)1785 mpc52xx_uart_of_suspend(struct platform_device *op, pm_message_t state)
1786 {
1787 struct uart_port *port = platform_get_drvdata(op);
1788
1789 if (port)
1790 uart_suspend_port(&mpc52xx_uart_driver, port);
1791
1792 return 0;
1793 }
1794
1795 static int
mpc52xx_uart_of_resume(struct platform_device * op)1796 mpc52xx_uart_of_resume(struct platform_device *op)
1797 {
1798 struct uart_port *port = platform_get_drvdata(op);
1799
1800 if (port)
1801 uart_resume_port(&mpc52xx_uart_driver, port);
1802
1803 return 0;
1804 }
1805 #endif
1806
1807 static void
mpc52xx_uart_of_assign(struct device_node * np)1808 mpc52xx_uart_of_assign(struct device_node *np)
1809 {
1810 int i;
1811
1812 /* Find the first free PSC number */
1813 for (i = 0; i < MPC52xx_PSC_MAXNUM; i++) {
1814 if (mpc52xx_uart_nodes[i] == NULL) {
1815 of_node_get(np);
1816 mpc52xx_uart_nodes[i] = np;
1817 return;
1818 }
1819 }
1820 }
1821
1822 static void
mpc52xx_uart_of_enumerate(void)1823 mpc52xx_uart_of_enumerate(void)
1824 {
1825 static int enum_done;
1826 struct device_node *np;
1827 const struct of_device_id *match;
1828 int i;
1829
1830 if (enum_done)
1831 return;
1832
1833 /* Assign index to each PSC in device tree */
1834 for_each_matching_node(np, mpc52xx_uart_of_match) {
1835 match = of_match_node(mpc52xx_uart_of_match, np);
1836 psc_ops = match->data;
1837 mpc52xx_uart_of_assign(np);
1838 }
1839
1840 enum_done = 1;
1841
1842 for (i = 0; i < MPC52xx_PSC_MAXNUM; i++) {
1843 if (mpc52xx_uart_nodes[i])
1844 pr_debug("%pOF assigned to ttyPSC%x\n",
1845 mpc52xx_uart_nodes[i], i);
1846 }
1847 }
1848
1849 MODULE_DEVICE_TABLE(of, mpc52xx_uart_of_match);
1850
1851 static struct platform_driver mpc52xx_uart_of_driver = {
1852 .probe = mpc52xx_uart_of_probe,
1853 .remove = mpc52xx_uart_of_remove,
1854 #ifdef CONFIG_PM
1855 .suspend = mpc52xx_uart_of_suspend,
1856 .resume = mpc52xx_uart_of_resume,
1857 #endif
1858 .driver = {
1859 .name = "mpc52xx-psc-uart",
1860 .of_match_table = mpc52xx_uart_of_match,
1861 },
1862 };
1863
1864
1865 /* ======================================================================== */
1866 /* Module */
1867 /* ======================================================================== */
1868
1869 static int __init
mpc52xx_uart_init(void)1870 mpc52xx_uart_init(void)
1871 {
1872 int ret;
1873
1874 printk(KERN_INFO "Serial: MPC52xx PSC UART driver\n");
1875
1876 ret = uart_register_driver(&mpc52xx_uart_driver);
1877 if (ret) {
1878 printk(KERN_ERR "%s: uart_register_driver failed (%i)\n",
1879 __FILE__, ret);
1880 return ret;
1881 }
1882
1883 mpc52xx_uart_of_enumerate();
1884
1885 /*
1886 * Map the PSC FIFO Controller and init if on MPC512x.
1887 */
1888 if (psc_ops && psc_ops->fifoc_init) {
1889 ret = psc_ops->fifoc_init();
1890 if (ret)
1891 goto err_init;
1892 }
1893
1894 ret = platform_driver_register(&mpc52xx_uart_of_driver);
1895 if (ret) {
1896 printk(KERN_ERR "%s: platform_driver_register failed (%i)\n",
1897 __FILE__, ret);
1898 goto err_reg;
1899 }
1900
1901 return 0;
1902 err_reg:
1903 if (psc_ops && psc_ops->fifoc_uninit)
1904 psc_ops->fifoc_uninit();
1905 err_init:
1906 uart_unregister_driver(&mpc52xx_uart_driver);
1907 return ret;
1908 }
1909
1910 static void __exit
mpc52xx_uart_exit(void)1911 mpc52xx_uart_exit(void)
1912 {
1913 if (psc_ops->fifoc_uninit)
1914 psc_ops->fifoc_uninit();
1915
1916 platform_driver_unregister(&mpc52xx_uart_of_driver);
1917 uart_unregister_driver(&mpc52xx_uart_driver);
1918 }
1919
1920
1921 module_init(mpc52xx_uart_init);
1922 module_exit(mpc52xx_uart_exit);
1923
1924 MODULE_AUTHOR("Sylvain Munaut <tnt@246tNt.com>");
1925 MODULE_DESCRIPTION("Freescale MPC52xx PSC UART");
1926 MODULE_LICENSE("GPL");
1927