1 /* atarilance.c: Ethernet driver for VME Lance cards on the Atari */
2 /*
3 Written 1995/96 by Roman Hodek (Roman.Hodek@informatik.uni-erlangen.de)
4
5 This software may be used and distributed according to the terms
6 of the GNU General Public License, incorporated herein by reference.
7
8 This drivers was written with the following sources of reference:
9 - The driver for the Riebl Lance card by the TU Vienna.
10 - The modified TUW driver for PAM's VME cards
11 - The PC-Linux driver for Lance cards (but this is for bus master
12 cards, not the shared memory ones)
13 - The Amiga Ariadne driver
14
15 v1.0: (in 1.2.13pl4/0.9.13)
16 Initial version
17 v1.1: (in 1.2.13pl5)
18 more comments
19 deleted some debugging stuff
20 optimized register access (keep AREG pointing to CSR0)
21 following AMD, CSR0_STRT should be set only after IDON is detected
22 use memcpy() for data transfers, that also employs long word moves
23 better probe procedure for 24-bit systems
24 non-VME-RieblCards need extra delays in memcpy
25 must also do write test, since 0xfxe00000 may hit ROM
26 use 8/32 tx/rx buffers, which should give better NFS performance;
27 this is made possible by shifting the last packet buffer after the
28 RieblCard reserved area
29 v1.2: (in 1.2.13pl8)
30 again fixed probing for the Falcon; 0xfe01000 hits phys. 0x00010000
31 and thus RAM, in case of no Lance found all memory contents have to
32 be restored!
33 Now possible to compile as module.
34 v1.3: 03/30/96 Jes Sorensen, Roman (in 1.3)
35 Several little 1.3 adaptions
36 When the lance is stopped it jumps back into little-endian
37 mode. It is therefore necessary to put it back where it
38 belongs, in big endian mode, in order to make things work.
39 This might be the reason why multicast-mode didn't work
40 before, but I'm not able to test it as I only got an Amiga
41 (we had similar problems with the A2065 driver).
42
43 */
44
45 static const char version[] = "atarilance.c: v1.3 04/04/96 "
46 "Roman.Hodek@informatik.uni-erlangen.de\n";
47
48 #include <linux/netdevice.h>
49 #include <linux/etherdevice.h>
50 #include <linux/module.h>
51 #include <linux/stddef.h>
52 #include <linux/kernel.h>
53 #include <linux/string.h>
54 #include <linux/errno.h>
55 #include <linux/skbuff.h>
56 #include <linux/interrupt.h>
57 #include <linux/init.h>
58 #include <linux/bitops.h>
59
60 #include <asm/setup.h>
61 #include <asm/irq.h>
62 #include <asm/atarihw.h>
63 #include <asm/atariints.h>
64 #include <asm/io.h>
65
66 /* Debug level:
67 * 0 = silent, print only serious errors
68 * 1 = normal, print error messages
69 * 2 = debug, print debug infos
70 * 3 = debug, print even more debug infos (packet data)
71 */
72
73 #define LANCE_DEBUG 1
74
75 #ifdef LANCE_DEBUG
76 static int lance_debug = LANCE_DEBUG;
77 #else
78 static int lance_debug = 1;
79 #endif
80 module_param(lance_debug, int, 0);
81 MODULE_PARM_DESC(lance_debug, "atarilance debug level (0-3)");
82 MODULE_DESCRIPTION("Atari LANCE Ethernet driver");
83 MODULE_LICENSE("GPL");
84
85 /* Print debug messages on probing? */
86 #undef LANCE_DEBUG_PROBE
87
88 #define DPRINTK(n,a) \
89 do { \
90 if (lance_debug >= n) \
91 printk a; \
92 } while( 0 )
93
94 #ifdef LANCE_DEBUG_PROBE
95 # define PROBE_PRINT(a) printk a
96 #else
97 # define PROBE_PRINT(a)
98 #endif
99
100 /* These define the number of Rx and Tx buffers as log2. (Only powers
101 * of two are valid)
102 * Much more rx buffers (32) are reserved than tx buffers (8), since receiving
103 * is more time critical then sending and packets may have to remain in the
104 * board's memory when main memory is low.
105 */
106
107 #define TX_LOG_RING_SIZE 3
108 #define RX_LOG_RING_SIZE 5
109
110 /* These are the derived values */
111
112 #define TX_RING_SIZE (1 << TX_LOG_RING_SIZE)
113 #define TX_RING_LEN_BITS (TX_LOG_RING_SIZE << 5)
114 #define TX_RING_MOD_MASK (TX_RING_SIZE - 1)
115
116 #define RX_RING_SIZE (1 << RX_LOG_RING_SIZE)
117 #define RX_RING_LEN_BITS (RX_LOG_RING_SIZE << 5)
118 #define RX_RING_MOD_MASK (RX_RING_SIZE - 1)
119
120 #define TX_TIMEOUT (HZ/5)
121
122 /* The LANCE Rx and Tx ring descriptors. */
123 struct lance_rx_head {
124 unsigned short base; /* Low word of base addr */
125 volatile unsigned char flag;
126 unsigned char base_hi; /* High word of base addr (unused) */
127 short buf_length; /* This length is 2s complement! */
128 volatile short msg_length; /* This length is "normal". */
129 };
130
131 struct lance_tx_head {
132 unsigned short base; /* Low word of base addr */
133 volatile unsigned char flag;
134 unsigned char base_hi; /* High word of base addr (unused) */
135 short length; /* Length is 2s complement! */
136 volatile short misc;
137 };
138
139 struct ringdesc {
140 unsigned short adr_lo; /* Low 16 bits of address */
141 unsigned char len; /* Length bits */
142 unsigned char adr_hi; /* High 8 bits of address (unused) */
143 };
144
145 /* The LANCE initialization block, described in databook. */
146 struct lance_init_block {
147 unsigned short mode; /* Pre-set mode */
148 unsigned char hwaddr[6]; /* Physical ethernet address */
149 unsigned filter[2]; /* Multicast filter (unused). */
150 /* Receive and transmit ring base, along with length bits. */
151 struct ringdesc rx_ring;
152 struct ringdesc tx_ring;
153 };
154
155 /* The whole layout of the Lance shared memory */
156 struct lance_memory {
157 struct lance_init_block init;
158 struct lance_tx_head tx_head[TX_RING_SIZE];
159 struct lance_rx_head rx_head[RX_RING_SIZE];
160 char packet_area[]; /* packet data follow after the
161 * init block and the ring
162 * descriptors and are located
163 * at runtime */
164 };
165
166 /* RieblCard specifics:
167 * The original TOS driver for these cards reserves the area from offset
168 * 0xee70 to 0xeebb for storing configuration data. Of interest to us is the
169 * Ethernet address there, and the magic for verifying the data's validity.
170 * The reserved area isn't touch by packet buffers. Furthermore, offset 0xfffe
171 * is reserved for the interrupt vector number.
172 */
173 #define RIEBL_RSVD_START 0xee70
174 #define RIEBL_RSVD_END 0xeec0
175 #define RIEBL_MAGIC 0x09051990
176 #define RIEBL_MAGIC_ADDR ((unsigned long *)(((char *)MEM) + 0xee8a))
177 #define RIEBL_HWADDR_ADDR ((unsigned char *)(((char *)MEM) + 0xee8e))
178 #define RIEBL_IVEC_ADDR ((unsigned short *)(((char *)MEM) + 0xfffe))
179
180 /* This is a default address for the old RieblCards without a battery
181 * that have no ethernet address at boot time. 00:00:36:04 is the
182 * prefix for Riebl cards, the 00:00 at the end is arbitrary.
183 */
184
185 static unsigned char OldRieblDefHwaddr[6] = {
186 0x00, 0x00, 0x36, 0x04, 0x00, 0x00
187 };
188
189
190 /* I/O registers of the Lance chip */
191
192 struct lance_ioreg {
193 /* base+0x0 */ volatile unsigned short data;
194 /* base+0x2 */ volatile unsigned short addr;
195 unsigned char _dummy1[3];
196 /* base+0x7 */ volatile unsigned char ivec;
197 unsigned char _dummy2[5];
198 /* base+0xd */ volatile unsigned char eeprom;
199 unsigned char _dummy3;
200 /* base+0xf */ volatile unsigned char mem;
201 };
202
203 /* Types of boards this driver supports */
204
205 enum lance_type {
206 OLD_RIEBL, /* old Riebl card without battery */
207 NEW_RIEBL, /* new Riebl card with battery */
208 PAM_CARD /* PAM card with EEPROM */
209 };
210
211 static char *lance_names[] = {
212 "Riebl-Card (without battery)",
213 "Riebl-Card (with battery)",
214 "PAM intern card"
215 };
216
217 /* The driver's private device structure */
218
219 struct lance_private {
220 enum lance_type cardtype;
221 struct lance_ioreg *iobase;
222 struct lance_memory *mem;
223 int cur_rx, cur_tx; /* The next free ring entry */
224 int dirty_tx; /* Ring entries to be freed. */
225 /* copy function */
226 void *(*memcpy_f)( void *, const void *, size_t );
227 /* This must be long for set_bit() */
228 long tx_full;
229 spinlock_t devlock;
230 };
231
232 /* I/O register access macros */
233
234 #define MEM lp->mem
235 #define DREG IO->data
236 #define AREG IO->addr
237 #define REGA(a) (*( AREG = (a), &DREG ))
238
239 /* Definitions for packet buffer access: */
240 #define PKT_BUF_SZ 1544
241 /* Get the address of a packet buffer corresponding to a given buffer head */
242 #define PKTBUF_ADDR(head) (((unsigned char *)(MEM)) + (head)->base)
243
244 /* Possible memory/IO addresses for probing */
245
246 static struct lance_addr {
247 unsigned long memaddr;
248 unsigned long ioaddr;
249 int slow_flag;
250 } lance_addr_list[] = {
251 { 0xfe010000, 0xfe00fff0, 0 }, /* RieblCard VME in TT */
252 { 0xffc10000, 0xffc0fff0, 0 }, /* RieblCard VME in MegaSTE
253 (highest byte stripped) */
254 { 0xffe00000, 0xffff7000, 1 }, /* RieblCard in ST
255 (highest byte stripped) */
256 { 0xffd00000, 0xffff7000, 1 }, /* RieblCard in ST with hw modif. to
257 avoid conflict with ROM
258 (highest byte stripped) */
259 { 0xffcf0000, 0xffcffff0, 0 }, /* PAMCard VME in TT and MSTE
260 (highest byte stripped) */
261 { 0xfecf0000, 0xfecffff0, 0 }, /* Rhotron's PAMCard VME in TT and MSTE
262 (highest byte stripped) */
263 };
264
265 #define N_LANCE_ADDR ARRAY_SIZE(lance_addr_list)
266
267
268 /* Definitions for the Lance */
269
270 /* tx_head flags */
271 #define TMD1_ENP 0x01 /* end of packet */
272 #define TMD1_STP 0x02 /* start of packet */
273 #define TMD1_DEF 0x04 /* deferred */
274 #define TMD1_ONE 0x08 /* one retry needed */
275 #define TMD1_MORE 0x10 /* more than one retry needed */
276 #define TMD1_ERR 0x40 /* error summary */
277 #define TMD1_OWN 0x80 /* ownership (set: chip owns) */
278
279 #define TMD1_OWN_CHIP TMD1_OWN
280 #define TMD1_OWN_HOST 0
281
282 /* tx_head misc field */
283 #define TMD3_TDR 0x03FF /* Time Domain Reflectometry counter */
284 #define TMD3_RTRY 0x0400 /* failed after 16 retries */
285 #define TMD3_LCAR 0x0800 /* carrier lost */
286 #define TMD3_LCOL 0x1000 /* late collision */
287 #define TMD3_UFLO 0x4000 /* underflow (late memory) */
288 #define TMD3_BUFF 0x8000 /* buffering error (no ENP) */
289
290 /* rx_head flags */
291 #define RMD1_ENP 0x01 /* end of packet */
292 #define RMD1_STP 0x02 /* start of packet */
293 #define RMD1_BUFF 0x04 /* buffer error */
294 #define RMD1_CRC 0x08 /* CRC error */
295 #define RMD1_OFLO 0x10 /* overflow */
296 #define RMD1_FRAM 0x20 /* framing error */
297 #define RMD1_ERR 0x40 /* error summary */
298 #define RMD1_OWN 0x80 /* ownership (set: ship owns) */
299
300 #define RMD1_OWN_CHIP RMD1_OWN
301 #define RMD1_OWN_HOST 0
302
303 /* register names */
304 #define CSR0 0 /* mode/status */
305 #define CSR1 1 /* init block addr (low) */
306 #define CSR2 2 /* init block addr (high) */
307 #define CSR3 3 /* misc */
308 #define CSR8 8 /* address filter */
309 #define CSR15 15 /* promiscuous mode */
310
311 /* CSR0 */
312 /* (R=readable, W=writeable, S=set on write, C=clear on write) */
313 #define CSR0_INIT 0x0001 /* initialize (RS) */
314 #define CSR0_STRT 0x0002 /* start (RS) */
315 #define CSR0_STOP 0x0004 /* stop (RS) */
316 #define CSR0_TDMD 0x0008 /* transmit demand (RS) */
317 #define CSR0_TXON 0x0010 /* transmitter on (R) */
318 #define CSR0_RXON 0x0020 /* receiver on (R) */
319 #define CSR0_INEA 0x0040 /* interrupt enable (RW) */
320 #define CSR0_INTR 0x0080 /* interrupt active (R) */
321 #define CSR0_IDON 0x0100 /* initialization done (RC) */
322 #define CSR0_TINT 0x0200 /* transmitter interrupt (RC) */
323 #define CSR0_RINT 0x0400 /* receiver interrupt (RC) */
324 #define CSR0_MERR 0x0800 /* memory error (RC) */
325 #define CSR0_MISS 0x1000 /* missed frame (RC) */
326 #define CSR0_CERR 0x2000 /* carrier error (no heartbeat :-) (RC) */
327 #define CSR0_BABL 0x4000 /* babble: tx-ed too many bits (RC) */
328 #define CSR0_ERR 0x8000 /* error (RC) */
329
330 /* CSR3 */
331 #define CSR3_BCON 0x0001 /* byte control */
332 #define CSR3_ACON 0x0002 /* ALE control */
333 #define CSR3_BSWP 0x0004 /* byte swap (1=big endian) */
334
335
336
337 /***************************** Prototypes *****************************/
338
339 static unsigned long lance_probe1( struct net_device *dev, struct lance_addr
340 *init_rec );
341 static int lance_open( struct net_device *dev );
342 static void lance_init_ring( struct net_device *dev );
343 static netdev_tx_t lance_start_xmit(struct sk_buff *skb,
344 struct net_device *dev);
345 static irqreturn_t lance_interrupt( int irq, void *dev_id );
346 static int lance_rx( struct net_device *dev );
347 static int lance_close( struct net_device *dev );
348 static void set_multicast_list( struct net_device *dev );
349 static int lance_set_mac_address( struct net_device *dev, void *addr );
350 static void lance_tx_timeout (struct net_device *dev, unsigned int txqueue);
351
352 /************************* End of Prototypes **************************/
353
354
355
356
357
slow_memcpy(void * dst,const void * src,size_t len)358 static void *slow_memcpy( void *dst, const void *src, size_t len )
359
360 { char *cto = dst;
361 const char *cfrom = src;
362
363 while( len-- ) {
364 *cto++ = *cfrom++;
365 MFPDELAY();
366 }
367 return dst;
368 }
369
370
atarilance_probe(void)371 static struct net_device * __init atarilance_probe(void)
372 {
373 int i;
374 static int found;
375 struct net_device *dev;
376 int err = -ENODEV;
377
378 if (!MACH_IS_ATARI || found)
379 /* Assume there's only one board possible... That seems true, since
380 * the Riebl/PAM board's address cannot be changed. */
381 return ERR_PTR(-ENODEV);
382
383 dev = alloc_etherdev(sizeof(struct lance_private));
384 if (!dev)
385 return ERR_PTR(-ENOMEM);
386
387 for( i = 0; i < N_LANCE_ADDR; ++i ) {
388 if (lance_probe1( dev, &lance_addr_list[i] )) {
389 found = 1;
390 err = register_netdev(dev);
391 if (!err)
392 return dev;
393 free_irq(dev->irq, dev);
394 break;
395 }
396 }
397 free_netdev(dev);
398 return ERR_PTR(err);
399 }
400
401
402 /* Derived from hwreg_present() in atari/config.c: */
403
addr_accessible(volatile void * regp,int wordflag,int writeflag)404 static noinline int __init addr_accessible(volatile void *regp, int wordflag,
405 int writeflag)
406 {
407 int ret;
408 unsigned long flags;
409 long *vbr, save_berr;
410
411 local_irq_save(flags);
412
413 __asm__ __volatile__ ( "movec %/vbr,%0" : "=r" (vbr) : );
414 save_berr = vbr[2];
415
416 __asm__ __volatile__
417 ( "movel %/sp,%/d1\n\t"
418 "movel #Lberr,%2@\n\t"
419 "moveq #0,%0\n\t"
420 "tstl %3\n\t"
421 "bne 1f\n\t"
422 "moveb %1@,%/d0\n\t"
423 "nop \n\t"
424 "bra 2f\n"
425 "1: movew %1@,%/d0\n\t"
426 "nop \n"
427 "2: tstl %4\n\t"
428 "beq 2f\n\t"
429 "tstl %3\n\t"
430 "bne 1f\n\t"
431 "clrb %1@\n\t"
432 "nop \n\t"
433 "moveb %/d0,%1@\n\t"
434 "nop \n\t"
435 "bra 2f\n"
436 "1: clrw %1@\n\t"
437 "nop \n\t"
438 "movew %/d0,%1@\n\t"
439 "nop \n"
440 "2: moveq #1,%0\n"
441 "Lberr: movel %/d1,%/sp"
442 : "=&d" (ret)
443 : "a" (regp), "a" (&vbr[2]), "rm" (wordflag), "rm" (writeflag)
444 : "d0", "d1", "memory"
445 );
446
447 vbr[2] = save_berr;
448 local_irq_restore(flags);
449
450 return ret;
451 }
452
453 static const struct net_device_ops lance_netdev_ops = {
454 .ndo_open = lance_open,
455 .ndo_stop = lance_close,
456 .ndo_start_xmit = lance_start_xmit,
457 .ndo_set_rx_mode = set_multicast_list,
458 .ndo_set_mac_address = lance_set_mac_address,
459 .ndo_tx_timeout = lance_tx_timeout,
460 .ndo_validate_addr = eth_validate_addr,
461 };
462
lance_probe1(struct net_device * dev,struct lance_addr * init_rec)463 static unsigned long __init lance_probe1( struct net_device *dev,
464 struct lance_addr *init_rec )
465 {
466 volatile unsigned short *memaddr =
467 (volatile unsigned short *)init_rec->memaddr;
468 volatile unsigned short *ioaddr =
469 (volatile unsigned short *)init_rec->ioaddr;
470 struct lance_private *lp;
471 struct lance_ioreg *IO;
472 int i;
473 static int did_version;
474 unsigned short save1, save2;
475 u8 addr[ETH_ALEN];
476
477 PROBE_PRINT(( "Probing for Lance card at mem %#lx io %#lx\n",
478 (long)memaddr, (long)ioaddr ));
479
480 /* Test whether memory readable and writable */
481 PROBE_PRINT(( "lance_probe1: testing memory to be accessible\n" ));
482 if (!addr_accessible( memaddr, 1, 1 )) goto probe_fail;
483
484 /* Written values should come back... */
485 PROBE_PRINT(( "lance_probe1: testing memory to be writable (1)\n" ));
486 save1 = *memaddr;
487 *memaddr = 0x0001;
488 if (*memaddr != 0x0001) goto probe_fail;
489 PROBE_PRINT(( "lance_probe1: testing memory to be writable (2)\n" ));
490 *memaddr = 0x0000;
491 if (*memaddr != 0x0000) goto probe_fail;
492 *memaddr = save1;
493
494 /* First port should be readable and writable */
495 PROBE_PRINT(( "lance_probe1: testing ioport to be accessible\n" ));
496 if (!addr_accessible( ioaddr, 1, 1 )) goto probe_fail;
497
498 /* and written values should be readable */
499 PROBE_PRINT(( "lance_probe1: testing ioport to be writeable\n" ));
500 save2 = ioaddr[1];
501 ioaddr[1] = 0x0001;
502 if (ioaddr[1] != 0x0001) goto probe_fail;
503
504 /* The CSR0_INIT bit should not be readable */
505 PROBE_PRINT(( "lance_probe1: testing CSR0 register function (1)\n" ));
506 save1 = ioaddr[0];
507 ioaddr[1] = CSR0;
508 ioaddr[0] = CSR0_INIT | CSR0_STOP;
509 if (ioaddr[0] != CSR0_STOP) {
510 ioaddr[0] = save1;
511 ioaddr[1] = save2;
512 goto probe_fail;
513 }
514 PROBE_PRINT(( "lance_probe1: testing CSR0 register function (2)\n" ));
515 ioaddr[0] = CSR0_STOP;
516 if (ioaddr[0] != CSR0_STOP) {
517 ioaddr[0] = save1;
518 ioaddr[1] = save2;
519 goto probe_fail;
520 }
521
522 /* Now ok... */
523 PROBE_PRINT(( "lance_probe1: Lance card detected\n" ));
524 goto probe_ok;
525
526 probe_fail:
527 return 0;
528
529 probe_ok:
530 lp = netdev_priv(dev);
531 MEM = (struct lance_memory *)memaddr;
532 IO = lp->iobase = (struct lance_ioreg *)ioaddr;
533 dev->base_addr = (unsigned long)ioaddr; /* informational only */
534 lp->memcpy_f = init_rec->slow_flag ? slow_memcpy : memcpy;
535
536 REGA( CSR0 ) = CSR0_STOP;
537
538 /* Now test for type: If the eeprom I/O port is readable, it is a
539 * PAM card */
540 if (addr_accessible( &(IO->eeprom), 0, 0 )) {
541 /* Switch back to Ram */
542 i = IO->mem;
543 lp->cardtype = PAM_CARD;
544 }
545 else if (*RIEBL_MAGIC_ADDR == RIEBL_MAGIC) {
546 lp->cardtype = NEW_RIEBL;
547 }
548 else
549 lp->cardtype = OLD_RIEBL;
550
551 if (lp->cardtype == PAM_CARD ||
552 memaddr == (unsigned short *)0xffe00000) {
553 /* PAMs card and Riebl on ST use level 5 autovector */
554 if (request_irq(IRQ_AUTO_5, lance_interrupt, 0,
555 "PAM,Riebl-ST Ethernet", dev)) {
556 printk( "Lance: request for irq %d failed\n", IRQ_AUTO_5 );
557 return 0;
558 }
559 dev->irq = IRQ_AUTO_5;
560 }
561 else {
562 /* For VME-RieblCards, request a free VME int */
563 unsigned int irq = atari_register_vme_int();
564 if (!irq) {
565 printk( "Lance: request for VME interrupt failed\n" );
566 return 0;
567 }
568 if (request_irq(irq, lance_interrupt, 0, "Riebl-VME Ethernet",
569 dev)) {
570 printk( "Lance: request for irq %u failed\n", irq );
571 return 0;
572 }
573 dev->irq = irq;
574 }
575
576 printk("%s: %s at io %#lx, mem %#lx, irq %d%s, hwaddr ",
577 dev->name, lance_names[lp->cardtype],
578 (unsigned long)ioaddr,
579 (unsigned long)memaddr,
580 dev->irq,
581 init_rec->slow_flag ? " (slow memcpy)" : "" );
582
583 /* Get the ethernet address */
584 switch( lp->cardtype ) {
585 case OLD_RIEBL:
586 /* No ethernet address! (Set some default address) */
587 eth_hw_addr_set(dev, OldRieblDefHwaddr);
588 break;
589 case NEW_RIEBL:
590 lp->memcpy_f(addr, RIEBL_HWADDR_ADDR, ETH_ALEN);
591 eth_hw_addr_set(dev, addr);
592 break;
593 case PAM_CARD:
594 i = IO->eeprom;
595 for( i = 0; i < 6; ++i )
596 addr[i] =
597 ((((unsigned short *)MEM)[i*2] & 0x0f) << 4) |
598 ((((unsigned short *)MEM)[i*2+1] & 0x0f));
599 eth_hw_addr_set(dev, addr);
600 i = IO->mem;
601 break;
602 }
603 printk("%pM\n", dev->dev_addr);
604 if (lp->cardtype == OLD_RIEBL) {
605 printk( "%s: Warning: This is a default ethernet address!\n",
606 dev->name );
607 printk( " Use \"ifconfig hw ether ...\" to set the address.\n" );
608 }
609
610 spin_lock_init(&lp->devlock);
611
612 MEM->init.mode = 0x0000; /* Disable Rx and Tx. */
613 for( i = 0; i < 6; i++ )
614 MEM->init.hwaddr[i] = dev->dev_addr[i^1]; /* <- 16 bit swap! */
615 MEM->init.filter[0] = 0x00000000;
616 MEM->init.filter[1] = 0x00000000;
617 MEM->init.rx_ring.adr_lo = offsetof( struct lance_memory, rx_head );
618 MEM->init.rx_ring.adr_hi = 0;
619 MEM->init.rx_ring.len = RX_RING_LEN_BITS;
620 MEM->init.tx_ring.adr_lo = offsetof( struct lance_memory, tx_head );
621 MEM->init.tx_ring.adr_hi = 0;
622 MEM->init.tx_ring.len = TX_RING_LEN_BITS;
623
624 if (lp->cardtype == PAM_CARD)
625 IO->ivec = IRQ_SOURCE_TO_VECTOR(dev->irq);
626 else
627 *RIEBL_IVEC_ADDR = IRQ_SOURCE_TO_VECTOR(dev->irq);
628
629 if (did_version++ == 0)
630 DPRINTK( 1, ( version ));
631
632 dev->netdev_ops = &lance_netdev_ops;
633
634 /* XXX MSch */
635 dev->watchdog_timeo = TX_TIMEOUT;
636
637 return 1;
638 }
639
640
lance_open(struct net_device * dev)641 static int lance_open( struct net_device *dev )
642 {
643 struct lance_private *lp = netdev_priv(dev);
644 struct lance_ioreg *IO = lp->iobase;
645 int i;
646
647 DPRINTK( 2, ( "%s: lance_open()\n", dev->name ));
648
649 lance_init_ring(dev);
650 /* Re-initialize the LANCE, and start it when done. */
651
652 REGA( CSR3 ) = CSR3_BSWP | (lp->cardtype == PAM_CARD ? CSR3_ACON : 0);
653 REGA( CSR2 ) = 0;
654 REGA( CSR1 ) = 0;
655 REGA( CSR0 ) = CSR0_INIT;
656 /* From now on, AREG is kept to point to CSR0 */
657
658 i = 1000000;
659 while (--i > 0)
660 if (DREG & CSR0_IDON)
661 break;
662 if (i <= 0 || (DREG & CSR0_ERR)) {
663 DPRINTK( 2, ( "lance_open(): opening %s failed, i=%d, csr0=%04x\n",
664 dev->name, i, DREG ));
665 DREG = CSR0_STOP;
666 return -EIO;
667 }
668 DREG = CSR0_IDON;
669 DREG = CSR0_STRT;
670 DREG = CSR0_INEA;
671
672 netif_start_queue (dev);
673
674 DPRINTK( 2, ( "%s: LANCE is open, csr0 %04x\n", dev->name, DREG ));
675
676 return 0;
677 }
678
679
680 /* Initialize the LANCE Rx and Tx rings. */
681
lance_init_ring(struct net_device * dev)682 static void lance_init_ring( struct net_device *dev )
683 {
684 struct lance_private *lp = netdev_priv(dev);
685 int i;
686 unsigned offset;
687
688 lp->tx_full = 0;
689 lp->cur_rx = lp->cur_tx = 0;
690 lp->dirty_tx = 0;
691
692 offset = offsetof( struct lance_memory, packet_area );
693
694 /* If the packet buffer at offset 'o' would conflict with the reserved area
695 * of RieblCards, advance it */
696 #define CHECK_OFFSET(o) \
697 do { \
698 if (lp->cardtype == OLD_RIEBL || lp->cardtype == NEW_RIEBL) { \
699 if (((o) < RIEBL_RSVD_START) ? (o)+PKT_BUF_SZ > RIEBL_RSVD_START \
700 : (o) < RIEBL_RSVD_END) \
701 (o) = RIEBL_RSVD_END; \
702 } \
703 } while(0)
704
705 for( i = 0; i < TX_RING_SIZE; i++ ) {
706 CHECK_OFFSET(offset);
707 MEM->tx_head[i].base = offset;
708 MEM->tx_head[i].flag = TMD1_OWN_HOST;
709 MEM->tx_head[i].base_hi = 0;
710 MEM->tx_head[i].length = 0;
711 MEM->tx_head[i].misc = 0;
712 offset += PKT_BUF_SZ;
713 }
714
715 for( i = 0; i < RX_RING_SIZE; i++ ) {
716 CHECK_OFFSET(offset);
717 MEM->rx_head[i].base = offset;
718 MEM->rx_head[i].flag = TMD1_OWN_CHIP;
719 MEM->rx_head[i].base_hi = 0;
720 MEM->rx_head[i].buf_length = -PKT_BUF_SZ;
721 MEM->rx_head[i].msg_length = 0;
722 offset += PKT_BUF_SZ;
723 }
724 }
725
726
727 /* XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX */
728
729
lance_tx_timeout(struct net_device * dev,unsigned int txqueue)730 static void lance_tx_timeout (struct net_device *dev, unsigned int txqueue)
731 {
732 struct lance_private *lp = netdev_priv(dev);
733 struct lance_ioreg *IO = lp->iobase;
734
735 AREG = CSR0;
736 DPRINTK( 1, ( "%s: transmit timed out, status %04x, resetting.\n",
737 dev->name, DREG ));
738 DREG = CSR0_STOP;
739 /*
740 * Always set BSWP after a STOP as STOP puts it back into
741 * little endian mode.
742 */
743 REGA( CSR3 ) = CSR3_BSWP | (lp->cardtype == PAM_CARD ? CSR3_ACON : 0);
744 dev->stats.tx_errors++;
745 #ifndef final_version
746 { int i;
747 DPRINTK( 2, ( "Ring data: dirty_tx %d cur_tx %d%s cur_rx %d\n",
748 lp->dirty_tx, lp->cur_tx,
749 lp->tx_full ? " (full)" : "",
750 lp->cur_rx ));
751 for( i = 0 ; i < RX_RING_SIZE; i++ )
752 DPRINTK( 2, ( "rx #%d: base=%04x blen=%04x mlen=%04x\n",
753 i, MEM->rx_head[i].base,
754 -MEM->rx_head[i].buf_length,
755 MEM->rx_head[i].msg_length ));
756 for( i = 0 ; i < TX_RING_SIZE; i++ )
757 DPRINTK( 2, ( "tx #%d: base=%04x len=%04x misc=%04x\n",
758 i, MEM->tx_head[i].base,
759 -MEM->tx_head[i].length,
760 MEM->tx_head[i].misc ));
761 }
762 #endif
763 /* XXX MSch: maybe purge/reinit ring here */
764 /* lance_restart, essentially */
765 lance_init_ring(dev);
766 REGA( CSR0 ) = CSR0_INEA | CSR0_INIT | CSR0_STRT;
767 netif_trans_update(dev); /* prevent tx timeout */
768 netif_wake_queue(dev);
769 }
770
771 /* XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX */
772
773 static netdev_tx_t
lance_start_xmit(struct sk_buff * skb,struct net_device * dev)774 lance_start_xmit(struct sk_buff *skb, struct net_device *dev)
775 {
776 struct lance_private *lp = netdev_priv(dev);
777 struct lance_ioreg *IO = lp->iobase;
778 int entry, len;
779 struct lance_tx_head *head;
780 unsigned long flags;
781
782 DPRINTK( 2, ( "%s: lance_start_xmit() called, csr0 %4.4x.\n",
783 dev->name, DREG ));
784
785
786 /* The old LANCE chips doesn't automatically pad buffers to min. size. */
787 len = skb->len;
788 if (len < ETH_ZLEN)
789 len = ETH_ZLEN;
790 /* PAM-Card has a bug: Can only send packets with even number of bytes! */
791 else if (lp->cardtype == PAM_CARD && (len & 1))
792 ++len;
793
794 if (len > skb->len) {
795 if (skb_padto(skb, len))
796 return NETDEV_TX_OK;
797 }
798
799 netif_stop_queue (dev);
800
801 /* Fill in a Tx ring entry */
802 if (lance_debug >= 3) {
803 printk( "%s: TX pkt type 0x%04x from %pM to %pM"
804 " data at 0x%08x len %d\n",
805 dev->name, ((u_short *)skb->data)[6],
806 &skb->data[6], skb->data,
807 (int)skb->data, (int)skb->len );
808 }
809
810 /* We're not prepared for the int until the last flags are set/reset. And
811 * the int may happen already after setting the OWN_CHIP... */
812 spin_lock_irqsave (&lp->devlock, flags);
813
814 /* Mask to ring buffer boundary. */
815 entry = lp->cur_tx & TX_RING_MOD_MASK;
816 head = &(MEM->tx_head[entry]);
817
818 /* Caution: the write order is important here, set the "ownership" bits
819 * last.
820 */
821
822
823 head->length = -len;
824 head->misc = 0;
825 lp->memcpy_f( PKTBUF_ADDR(head), (void *)skb->data, skb->len );
826 head->flag = TMD1_OWN_CHIP | TMD1_ENP | TMD1_STP;
827 dev->stats.tx_bytes += skb->len;
828 dev_consume_skb_irq(skb);
829 lp->cur_tx++;
830 while( lp->cur_tx >= TX_RING_SIZE && lp->dirty_tx >= TX_RING_SIZE ) {
831 lp->cur_tx -= TX_RING_SIZE;
832 lp->dirty_tx -= TX_RING_SIZE;
833 }
834
835 /* Trigger an immediate send poll. */
836 DREG = CSR0_INEA | CSR0_TDMD;
837
838 if ((MEM->tx_head[(entry+1) & TX_RING_MOD_MASK].flag & TMD1_OWN) ==
839 TMD1_OWN_HOST)
840 netif_start_queue (dev);
841 else
842 lp->tx_full = 1;
843 spin_unlock_irqrestore (&lp->devlock, flags);
844
845 return NETDEV_TX_OK;
846 }
847
848 /* The LANCE interrupt handler. */
849
lance_interrupt(int irq,void * dev_id)850 static irqreturn_t lance_interrupt( int irq, void *dev_id )
851 {
852 struct net_device *dev = dev_id;
853 struct lance_private *lp;
854 struct lance_ioreg *IO;
855 int csr0, boguscnt = 10;
856 int handled = 0;
857
858 if (!dev) {
859 DPRINTK( 1, ( "lance_interrupt(): interrupt for unknown device.\n" ));
860 return IRQ_NONE;
861 }
862
863 lp = netdev_priv(dev);
864 IO = lp->iobase;
865 spin_lock (&lp->devlock);
866
867 AREG = CSR0;
868
869 while( ((csr0 = DREG) & (CSR0_ERR | CSR0_TINT | CSR0_RINT)) &&
870 --boguscnt >= 0) {
871 handled = 1;
872 /* Acknowledge all of the current interrupt sources ASAP. */
873 DREG = csr0 & ~(CSR0_INIT | CSR0_STRT | CSR0_STOP |
874 CSR0_TDMD | CSR0_INEA);
875
876 DPRINTK( 2, ( "%s: interrupt csr0=%04x new csr=%04x.\n",
877 dev->name, csr0, DREG ));
878
879 if (csr0 & CSR0_RINT) /* Rx interrupt */
880 lance_rx( dev );
881
882 if (csr0 & CSR0_TINT) { /* Tx-done interrupt */
883 int dirty_tx = lp->dirty_tx;
884
885 while( dirty_tx < lp->cur_tx) {
886 int entry = dirty_tx & TX_RING_MOD_MASK;
887 int status = MEM->tx_head[entry].flag;
888
889 if (status & TMD1_OWN_CHIP)
890 break; /* It still hasn't been Txed */
891
892 MEM->tx_head[entry].flag = 0;
893
894 if (status & TMD1_ERR) {
895 /* There was an major error, log it. */
896 int err_status = MEM->tx_head[entry].misc;
897 dev->stats.tx_errors++;
898 if (err_status & TMD3_RTRY) dev->stats.tx_aborted_errors++;
899 if (err_status & TMD3_LCAR) dev->stats.tx_carrier_errors++;
900 if (err_status & TMD3_LCOL) dev->stats.tx_window_errors++;
901 if (err_status & TMD3_UFLO) {
902 /* Ackk! On FIFO errors the Tx unit is turned off! */
903 dev->stats.tx_fifo_errors++;
904 /* Remove this verbosity later! */
905 DPRINTK( 1, ( "%s: Tx FIFO error! Status %04x\n",
906 dev->name, csr0 ));
907 /* Restart the chip. */
908 DREG = CSR0_STRT;
909 }
910 } else {
911 if (status & (TMD1_MORE | TMD1_ONE | TMD1_DEF))
912 dev->stats.collisions++;
913 dev->stats.tx_packets++;
914 }
915
916 /* XXX MSch: free skb?? */
917 dirty_tx++;
918 }
919
920 #ifndef final_version
921 if (lp->cur_tx - dirty_tx >= TX_RING_SIZE) {
922 DPRINTK( 0, ( "out-of-sync dirty pointer,"
923 " %d vs. %d, full=%ld.\n",
924 dirty_tx, lp->cur_tx, lp->tx_full ));
925 dirty_tx += TX_RING_SIZE;
926 }
927 #endif
928
929 if (lp->tx_full && (netif_queue_stopped(dev)) &&
930 dirty_tx > lp->cur_tx - TX_RING_SIZE + 2) {
931 /* The ring is no longer full, clear tbusy. */
932 lp->tx_full = 0;
933 netif_wake_queue (dev);
934 }
935
936 lp->dirty_tx = dirty_tx;
937 }
938
939 /* Log misc errors. */
940 if (csr0 & CSR0_BABL) dev->stats.tx_errors++; /* Tx babble. */
941 if (csr0 & CSR0_MISS) dev->stats.rx_errors++; /* Missed a Rx frame. */
942 if (csr0 & CSR0_MERR) {
943 DPRINTK( 1, ( "%s: Bus master arbitration failure (?!?), "
944 "status %04x.\n", dev->name, csr0 ));
945 /* Restart the chip. */
946 DREG = CSR0_STRT;
947 }
948 }
949
950 /* Clear any other interrupt, and set interrupt enable. */
951 DREG = CSR0_BABL | CSR0_CERR | CSR0_MISS | CSR0_MERR |
952 CSR0_IDON | CSR0_INEA;
953
954 DPRINTK( 2, ( "%s: exiting interrupt, csr0=%#04x.\n",
955 dev->name, DREG ));
956
957 spin_unlock (&lp->devlock);
958 return IRQ_RETVAL(handled);
959 }
960
961
lance_rx(struct net_device * dev)962 static int lance_rx( struct net_device *dev )
963 {
964 struct lance_private *lp = netdev_priv(dev);
965 int entry = lp->cur_rx & RX_RING_MOD_MASK;
966 int i;
967
968 DPRINTK( 2, ( "%s: rx int, flag=%04x\n", dev->name,
969 MEM->rx_head[entry].flag ));
970
971 /* If we own the next entry, it's a new packet. Send it up. */
972 while( (MEM->rx_head[entry].flag & RMD1_OWN) == RMD1_OWN_HOST ) {
973 struct lance_rx_head *head = &(MEM->rx_head[entry]);
974 int status = head->flag;
975
976 if (status != (RMD1_ENP|RMD1_STP)) { /* There was an error. */
977 /* There is a tricky error noted by John Murphy,
978 <murf@perftech.com> to Russ Nelson: Even with full-sized
979 buffers it's possible for a jabber packet to use two
980 buffers, with only the last correctly noting the error. */
981 if (status & RMD1_ENP) /* Only count a general error at the */
982 dev->stats.rx_errors++; /* end of a packet.*/
983 if (status & RMD1_FRAM) dev->stats.rx_frame_errors++;
984 if (status & RMD1_OFLO) dev->stats.rx_over_errors++;
985 if (status & RMD1_CRC) dev->stats.rx_crc_errors++;
986 if (status & RMD1_BUFF) dev->stats.rx_fifo_errors++;
987 head->flag &= (RMD1_ENP|RMD1_STP);
988 } else {
989 /* Malloc up new buffer, compatible with net-3. */
990 short pkt_len = head->msg_length & 0xfff;
991 struct sk_buff *skb;
992
993 if (pkt_len < 60) {
994 printk( "%s: Runt packet!\n", dev->name );
995 dev->stats.rx_errors++;
996 }
997 else {
998 skb = netdev_alloc_skb(dev, pkt_len + 2);
999 if (!skb) {
1000 for( i = 0; i < RX_RING_SIZE; i++ )
1001 if (MEM->rx_head[(entry+i) & RX_RING_MOD_MASK].flag &
1002 RMD1_OWN_CHIP)
1003 break;
1004
1005 if (i > RX_RING_SIZE - 2) {
1006 dev->stats.rx_dropped++;
1007 head->flag |= RMD1_OWN_CHIP;
1008 lp->cur_rx++;
1009 }
1010 break;
1011 }
1012
1013 if (lance_debug >= 3) {
1014 u_char *data = PKTBUF_ADDR(head);
1015
1016 printk(KERN_DEBUG "%s: RX pkt type 0x%04x from %pM to %pM "
1017 "data %8ph len %d\n",
1018 dev->name, ((u_short *)data)[6],
1019 &data[6], data, &data[15], pkt_len);
1020 }
1021
1022 skb_reserve( skb, 2 ); /* 16 byte align */
1023 skb_put( skb, pkt_len ); /* Make room */
1024 lp->memcpy_f( skb->data, PKTBUF_ADDR(head), pkt_len );
1025 skb->protocol = eth_type_trans( skb, dev );
1026 netif_rx( skb );
1027 dev->stats.rx_packets++;
1028 dev->stats.rx_bytes += pkt_len;
1029 }
1030 }
1031
1032 head->flag |= RMD1_OWN_CHIP;
1033 entry = (++lp->cur_rx) & RX_RING_MOD_MASK;
1034 }
1035 lp->cur_rx &= RX_RING_MOD_MASK;
1036
1037 /* From lance.c (Donald Becker): */
1038 /* We should check that at least two ring entries are free. If not,
1039 we should free one and mark stats->rx_dropped++. */
1040
1041 return 0;
1042 }
1043
1044
lance_close(struct net_device * dev)1045 static int lance_close( struct net_device *dev )
1046 {
1047 struct lance_private *lp = netdev_priv(dev);
1048 struct lance_ioreg *IO = lp->iobase;
1049
1050 netif_stop_queue (dev);
1051
1052 AREG = CSR0;
1053
1054 DPRINTK( 2, ( "%s: Shutting down ethercard, status was %2.2x.\n",
1055 dev->name, DREG ));
1056
1057 /* We stop the LANCE here -- it occasionally polls
1058 memory if we don't. */
1059 DREG = CSR0_STOP;
1060
1061 return 0;
1062 }
1063
1064
1065 /* Set or clear the multicast filter for this adaptor.
1066 num_addrs == -1 Promiscuous mode, receive all packets
1067 num_addrs == 0 Normal mode, clear multicast list
1068 num_addrs > 0 Multicast mode, receive normal and MC packets, and do
1069 best-effort filtering.
1070 */
1071
set_multicast_list(struct net_device * dev)1072 static void set_multicast_list( struct net_device *dev )
1073 {
1074 struct lance_private *lp = netdev_priv(dev);
1075 struct lance_ioreg *IO = lp->iobase;
1076
1077 if (netif_running(dev))
1078 /* Only possible if board is already started */
1079 return;
1080
1081 /* We take the simple way out and always enable promiscuous mode. */
1082 DREG = CSR0_STOP; /* Temporarily stop the lance. */
1083
1084 if (dev->flags & IFF_PROMISC) {
1085 /* Log any net taps. */
1086 DPRINTK( 2, ( "%s: Promiscuous mode enabled.\n", dev->name ));
1087 REGA( CSR15 ) = 0x8000; /* Set promiscuous mode */
1088 } else {
1089 short multicast_table[4];
1090 int num_addrs = netdev_mc_count(dev);
1091 int i;
1092 /* We don't use the multicast table, but rely on upper-layer
1093 * filtering. */
1094 memset( multicast_table, (num_addrs == 0) ? 0 : -1,
1095 sizeof(multicast_table) );
1096 for( i = 0; i < 4; i++ )
1097 REGA( CSR8+i ) = multicast_table[i];
1098 REGA( CSR15 ) = 0; /* Unset promiscuous mode */
1099 }
1100
1101 /*
1102 * Always set BSWP after a STOP as STOP puts it back into
1103 * little endian mode.
1104 */
1105 REGA( CSR3 ) = CSR3_BSWP | (lp->cardtype == PAM_CARD ? CSR3_ACON : 0);
1106
1107 /* Resume normal operation and reset AREG to CSR0 */
1108 REGA( CSR0 ) = CSR0_IDON | CSR0_INEA | CSR0_STRT;
1109 }
1110
1111
1112 /* This is needed for old RieblCards and possible for new RieblCards */
1113
lance_set_mac_address(struct net_device * dev,void * addr)1114 static int lance_set_mac_address( struct net_device *dev, void *addr )
1115 {
1116 struct lance_private *lp = netdev_priv(dev);
1117 struct sockaddr *saddr = addr;
1118 int i;
1119
1120 if (lp->cardtype != OLD_RIEBL && lp->cardtype != NEW_RIEBL)
1121 return -EOPNOTSUPP;
1122
1123 if (netif_running(dev)) {
1124 /* Only possible while card isn't started */
1125 DPRINTK( 1, ( "%s: hwaddr can be set only while card isn't open.\n",
1126 dev->name ));
1127 return -EIO;
1128 }
1129
1130 eth_hw_addr_set(dev, saddr->sa_data);
1131 for( i = 0; i < 6; i++ )
1132 MEM->init.hwaddr[i] = dev->dev_addr[i^1]; /* <- 16 bit swap! */
1133 lp->memcpy_f( RIEBL_HWADDR_ADDR, dev->dev_addr, 6 );
1134 /* set also the magic for future sessions */
1135 *RIEBL_MAGIC_ADDR = RIEBL_MAGIC;
1136
1137 return 0;
1138 }
1139
1140 static struct net_device *atarilance_dev;
1141
atarilance_module_init(void)1142 static int __init atarilance_module_init(void)
1143 {
1144 atarilance_dev = atarilance_probe();
1145 return PTR_ERR_OR_ZERO(atarilance_dev);
1146 }
1147
atarilance_module_exit(void)1148 static void __exit atarilance_module_exit(void)
1149 {
1150 unregister_netdev(atarilance_dev);
1151 free_irq(atarilance_dev->irq, atarilance_dev);
1152 free_netdev(atarilance_dev);
1153 }
1154 module_init(atarilance_module_init);
1155 module_exit(atarilance_module_exit);
1156