Home
last modified time | relevance | path

Searched refs:VDD (Results 1 – 25 of 38) sorted by relevance

12

/linux/Documentation/devicetree/bindings/sound/
H A Dimg,pistachio-internal-dac.txt10 - VDD-supply : Digital power supply regulator (+1.8V or +3.3V)
17 VDD-supply = <&supply3v3>;
H A Dda7218.txt11 - VDD-supply: VDD power supply for the device
60 - dlg,jack-threshold-pct : Threshold level for jack detection (% of VDD)
77 VDD-supply = <&reg_audio>;
/linux/Documentation/hwmon/
H A Dltc4282.rst70 in1_enable Enable/Disable VDD monitoring
71 in1_label Channel label (VDD)
130 in1_crit_fault_log Set to 1 by a VDD overvoltage fault occurring.
131 in1_lcrit_fault_log Set to 1 by a VDD undervoltage fault occurring.
H A Dltc2945.rst56 SENSE+ or VDD pin depending on chip configuration.
83 power1_input Power (in uW). Power is calculated based on SENSE+/VDD
H A Dw83795.rst52 24 3VDD 1Ch in12
108 18 3VDD 1Ch in12
H A Dgl518sm.rst61 zero'; this is important for negative voltage measurements. The VDD input
H A Dbt1-pvt.rst68 in0: VDD (processor core) 0.62V - 1.168V
/linux/drivers/hwmon/
H A Dgl518sm.c238 show(VDD, in_input0, voltage_in[0]);
242 show(VDD, in_min0, voltage_min[0]);
246 show(VDD, in_max0, voltage_max[0]);
329 set_low(VDD, in_min0, voltage_min[0], GL518_REG_VDD_LIMIT);
333 set_high(VDD, in_max0, voltage_max[0], GL518_REG_VDD_LIMIT);
/linux/Documentation/ABI/testing/
H A Dsysfs-bus-iio-thermocouple10 than VDD, otherwise '0'.
/linux/drivers/phy/qualcomm/
H A Dphy-qcom-usb-hs-28nm.c40 VDD, enumerator
344 priv->vregs[VDD].supply = "vdd"; in qcom_snps_hsphy_probe()
/linux/arch/arm64/boot/dts/hisilicon/
H A Dhikey970-pmic.dtsi74 ldo34: ldo34 { /* GPS AUX IN VDD */
/linux/arch/mips/boot/dts/img/
H A Dpistachio_marduk.dts76 VDD-supply = <&internal_dac_supply>;
/linux/arch/arm/boot/dts/allwinner/
H A Dsunxi-d1s-t113-mangopi-mq-r.dtsi47 /* SY8008 DC/DC regulator on the board, also supplying VDD-SYS */
H A Dsun8i-h3-orangepi-pc.dts188 * The datasheet uses 1.1V as the minimum value of VDD-CPUX,
/linux/arch/arm/boot/dts/microchip/
H A Dat91-sama5d4_ma5d4evk.dts159 regulator-name = "VDD MCI1";
H A Dat91-nattis-2-natte-2.dts38 regulator-name = "panel-VDD";
H A Dat91-sama5d4_xplained.dts292 regulator-name = "VDD MCI1";
/linux/arch/arm/boot/dts/st/
H A Dste-ux500-samsung-gavini.dts265 /* VDD 3V */
473 /* Used for VDD for sensors */
474 regulator-name = "V-SENSORS-VDD";
584 /* VDD is "digital supply" 1.71-3.47V */
H A Dste-ux500-samsung-skomer.dts337 /* Used for VDD for sensors */
460 /* VDD is "digital supply" nominally 1.71-3.6V */
H A Dste-ux500-samsung-kyle.dts357 /* Used for VDD for sensors */
468 /* VDD is "digital supply" 1.71-3.47V */
/linux/Documentation/w1/slaves/
H A Dw1_ds2438.rst83 battery input (VDD)
/linux/arch/arm64/boot/dts/freescale/
H A Dimx8mp-toradex-smarc-dev.dts216 /* Current measurement into module VDD */
H A Dimx8mp-dhcom-pdk2.dts128 reg_3p3vdd: regulator-3p3vdd { /* 3.3VDD */
H A Dimx8mp-dhcom-pdk3.dts134 reg_3p3vdd: regulator-3p3vdd { /* 3.3VDD */
/linux/Documentation/i2c/busses/
H A Di2c-parport.rst89 - Pins 4-9 (D2-D7) could be used as VDD is the driver drives them high.

12