1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * BCM6328 USBH PHY Controller Driver
4 *
5 * Copyright (C) 2020 Álvaro Fernández Rojas <noltari@gmail.com>
6 * Copyright (C) 2015 Simon Arlott
7 *
8 * Derived from bcm963xx_4.12L.06B_consumer/kernel/linux/arch/mips/bcm963xx/setup.c:
9 * Copyright (C) 2002 Broadcom Corporation
10 *
11 * Derived from OpenWrt patches:
12 * Copyright (C) 2013 Jonas Gorski <jonas.gorski@gmail.com>
13 * Copyright (C) 2013 Florian Fainelli <f.fainelli@gmail.com>
14 * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
15 */
16
17 #include <linux/clk.h>
18 #include <linux/io.h>
19 #include <linux/module.h>
20 #include <linux/of.h>
21 #include <linux/phy/phy.h>
22 #include <linux/platform_device.h>
23 #include <linux/reset.h>
24
25 /* USBH control register offsets */
26 enum usbh_regs {
27 USBH_BRT_CONTROL1 = 0,
28 USBH_BRT_CONTROL2,
29 USBH_BRT_STATUS1,
30 USBH_BRT_STATUS2,
31 USBH_UTMI_CONTROL1,
32 #define USBH_UC1_DEV_MODE_SEL BIT(0)
33 USBH_TEST_PORT_CONTROL,
34 USBH_PLL_CONTROL1,
35 #define USBH_PLLC_REFCLKSEL_SHIFT 0
36 #define USBH_PLLC_REFCLKSEL_MASK (0x3 << USBH_PLLC_REFCLKSEL_SHIFT)
37 #define USBH_PLLC_CLKSEL_SHIFT 2
38 #define USBH_PLLC_CLKSEL_MASK (0x3 << USBH_PLLC_CLKSEL_MASK)
39 #define USBH_PLLC_XTAL_PWRDWNB BIT(4)
40 #define USBH_PLLC_PLL_PWRDWNB BIT(5)
41 #define USBH_PLLC_PLL_CALEN BIT(6)
42 #define USBH_PLLC_PHYPLL_BYP BIT(7)
43 #define USBH_PLLC_PLL_RESET BIT(8)
44 #define USBH_PLLC_PLL_IDDQ_PWRDN BIT(9)
45 #define USBH_PLLC_PLL_PWRDN_DELAY BIT(10)
46 #define USBH_6318_PLLC_PLL_SUSPEND_EN BIT(27)
47 #define USBH_6318_PLLC_PHYPLL_BYP BIT(29)
48 #define USBH_6318_PLLC_PLL_RESET BIT(30)
49 #define USBH_6318_PLLC_PLL_IDDQ_PWRDN BIT(31)
50 USBH_SWAP_CONTROL,
51 #define USBH_SC_OHCI_DATA_SWAP BIT(0)
52 #define USBH_SC_OHCI_ENDIAN_SWAP BIT(1)
53 #define USBH_SC_OHCI_LOGICAL_ADDR_EN BIT(2)
54 #define USBH_SC_EHCI_DATA_SWAP BIT(3)
55 #define USBH_SC_EHCI_ENDIAN_SWAP BIT(4)
56 #define USBH_SC_EHCI_LOGICAL_ADDR_EN BIT(5)
57 #define USBH_SC_USB_DEVICE_SEL BIT(6)
58 USBH_GENERIC_CONTROL,
59 #define USBH_GC_PLL_SUSPEND_EN BIT(1)
60 USBH_FRAME_ADJUST_VALUE,
61 USBH_SETUP,
62 #define USBH_S_IOC BIT(4)
63 #define USBH_S_IPP BIT(5)
64 USBH_MDIO,
65 USBH_MDIO32,
66 USBH_USB_SIM_CONTROL,
67 #define USBH_USC_LADDR_SEL BIT(5)
68
69 __USBH_ENUM_SIZE
70 };
71
72 struct bcm63xx_usbh_phy_variant {
73 /* Registers */
74 long regs[__USBH_ENUM_SIZE];
75
76 /* PLLC bits to set/clear for power on */
77 u32 power_pllc_clr;
78 u32 power_pllc_set;
79
80 /* Setup bits to set/clear for power on */
81 u32 setup_clr;
82 u32 setup_set;
83
84 /* Swap Control bits to set */
85 u32 swapctl_dev_set;
86
87 /* Test Port Control value to set if non-zero */
88 u32 tpc_val;
89
90 /* USB Sim Control bits to set */
91 u32 usc_set;
92
93 /* UTMI Control 1 bits to set */
94 u32 utmictl1_dev_set;
95 };
96
97 struct bcm63xx_usbh_phy {
98 void __iomem *base;
99 struct clk *usbh_clk;
100 struct clk *usb_ref_clk;
101 struct reset_control *reset;
102 const struct bcm63xx_usbh_phy_variant *variant;
103 bool device_mode;
104 };
105
106 static const struct bcm63xx_usbh_phy_variant usbh_bcm6318 = {
107 .regs = {
108 [USBH_BRT_CONTROL1] = -1,
109 [USBH_BRT_CONTROL2] = -1,
110 [USBH_BRT_STATUS1] = -1,
111 [USBH_BRT_STATUS2] = -1,
112 [USBH_UTMI_CONTROL1] = 0x2c,
113 [USBH_TEST_PORT_CONTROL] = 0x1c,
114 [USBH_PLL_CONTROL1] = 0x04,
115 [USBH_SWAP_CONTROL] = 0x0c,
116 [USBH_GENERIC_CONTROL] = -1,
117 [USBH_FRAME_ADJUST_VALUE] = 0x08,
118 [USBH_SETUP] = 0x00,
119 [USBH_MDIO] = 0x14,
120 [USBH_MDIO32] = 0x18,
121 [USBH_USB_SIM_CONTROL] = 0x20,
122 },
123 .power_pllc_clr = USBH_6318_PLLC_PLL_IDDQ_PWRDN,
124 .power_pllc_set = USBH_6318_PLLC_PLL_SUSPEND_EN,
125 .setup_set = USBH_S_IOC,
126 .swapctl_dev_set = USBH_SC_USB_DEVICE_SEL,
127 .usc_set = USBH_USC_LADDR_SEL,
128 .utmictl1_dev_set = USBH_UC1_DEV_MODE_SEL,
129 };
130
131 static const struct bcm63xx_usbh_phy_variant usbh_bcm6328 = {
132 .regs = {
133 [USBH_BRT_CONTROL1] = 0x00,
134 [USBH_BRT_CONTROL2] = 0x04,
135 [USBH_BRT_STATUS1] = 0x08,
136 [USBH_BRT_STATUS2] = 0x0c,
137 [USBH_UTMI_CONTROL1] = 0x10,
138 [USBH_TEST_PORT_CONTROL] = 0x14,
139 [USBH_PLL_CONTROL1] = 0x18,
140 [USBH_SWAP_CONTROL] = 0x1c,
141 [USBH_GENERIC_CONTROL] = 0x20,
142 [USBH_FRAME_ADJUST_VALUE] = 0x24,
143 [USBH_SETUP] = 0x28,
144 [USBH_MDIO] = 0x2c,
145 [USBH_MDIO32] = 0x30,
146 [USBH_USB_SIM_CONTROL] = 0x34,
147 },
148 .setup_set = USBH_S_IOC,
149 .swapctl_dev_set = USBH_SC_USB_DEVICE_SEL,
150 .utmictl1_dev_set = USBH_UC1_DEV_MODE_SEL,
151 };
152
153 static const struct bcm63xx_usbh_phy_variant usbh_bcm6358 = {
154 .regs = {
155 [USBH_BRT_CONTROL1] = -1,
156 [USBH_BRT_CONTROL2] = -1,
157 [USBH_BRT_STATUS1] = -1,
158 [USBH_BRT_STATUS2] = -1,
159 [USBH_UTMI_CONTROL1] = -1,
160 [USBH_TEST_PORT_CONTROL] = 0x24,
161 [USBH_PLL_CONTROL1] = -1,
162 [USBH_SWAP_CONTROL] = 0x00,
163 [USBH_GENERIC_CONTROL] = -1,
164 [USBH_FRAME_ADJUST_VALUE] = -1,
165 [USBH_SETUP] = -1,
166 [USBH_MDIO] = -1,
167 [USBH_MDIO32] = -1,
168 [USBH_USB_SIM_CONTROL] = -1,
169 },
170 /*
171 * The magic value comes for the original vendor BSP
172 * and is needed for USB to work. Datasheet does not
173 * help, so the magic value is used as-is.
174 */
175 .tpc_val = 0x1c0020,
176 };
177
178 static const struct bcm63xx_usbh_phy_variant usbh_bcm6368 = {
179 .regs = {
180 [USBH_BRT_CONTROL1] = 0x00,
181 [USBH_BRT_CONTROL2] = 0x04,
182 [USBH_BRT_STATUS1] = 0x08,
183 [USBH_BRT_STATUS2] = 0x0c,
184 [USBH_UTMI_CONTROL1] = 0x10,
185 [USBH_TEST_PORT_CONTROL] = 0x14,
186 [USBH_PLL_CONTROL1] = 0x18,
187 [USBH_SWAP_CONTROL] = 0x1c,
188 [USBH_GENERIC_CONTROL] = -1,
189 [USBH_FRAME_ADJUST_VALUE] = 0x24,
190 [USBH_SETUP] = 0x28,
191 [USBH_MDIO] = 0x2c,
192 [USBH_MDIO32] = 0x30,
193 [USBH_USB_SIM_CONTROL] = 0x34,
194 },
195 .power_pllc_clr = USBH_PLLC_PLL_IDDQ_PWRDN | USBH_PLLC_PLL_PWRDN_DELAY,
196 .setup_set = USBH_S_IOC,
197 .swapctl_dev_set = USBH_SC_USB_DEVICE_SEL,
198 .utmictl1_dev_set = USBH_UC1_DEV_MODE_SEL,
199 };
200
201 static const struct bcm63xx_usbh_phy_variant usbh_bcm63268 = {
202 .regs = {
203 [USBH_BRT_CONTROL1] = 0x00,
204 [USBH_BRT_CONTROL2] = 0x04,
205 [USBH_BRT_STATUS1] = 0x08,
206 [USBH_BRT_STATUS2] = 0x0c,
207 [USBH_UTMI_CONTROL1] = 0x10,
208 [USBH_TEST_PORT_CONTROL] = 0x14,
209 [USBH_PLL_CONTROL1] = 0x18,
210 [USBH_SWAP_CONTROL] = 0x1c,
211 [USBH_GENERIC_CONTROL] = 0x20,
212 [USBH_FRAME_ADJUST_VALUE] = 0x24,
213 [USBH_SETUP] = 0x28,
214 [USBH_MDIO] = 0x2c,
215 [USBH_MDIO32] = 0x30,
216 [USBH_USB_SIM_CONTROL] = 0x34,
217 },
218 .power_pllc_clr = USBH_PLLC_PLL_IDDQ_PWRDN | USBH_PLLC_PLL_PWRDN_DELAY,
219 .setup_clr = USBH_S_IPP,
220 .setup_set = USBH_S_IOC,
221 .swapctl_dev_set = USBH_SC_USB_DEVICE_SEL,
222 .utmictl1_dev_set = USBH_UC1_DEV_MODE_SEL,
223 };
224
usbh_has_reg(struct bcm63xx_usbh_phy * usbh,int reg)225 static inline bool usbh_has_reg(struct bcm63xx_usbh_phy *usbh, int reg)
226 {
227 return (usbh->variant->regs[reg] >= 0);
228 }
229
usbh_readl(struct bcm63xx_usbh_phy * usbh,int reg)230 static inline u32 usbh_readl(struct bcm63xx_usbh_phy *usbh, int reg)
231 {
232 return __raw_readl(usbh->base + usbh->variant->regs[reg]);
233 }
234
usbh_writel(struct bcm63xx_usbh_phy * usbh,int reg,u32 value)235 static inline void usbh_writel(struct bcm63xx_usbh_phy *usbh, int reg,
236 u32 value)
237 {
238 __raw_writel(value, usbh->base + usbh->variant->regs[reg]);
239 }
240
bcm63xx_usbh_phy_init(struct phy * phy)241 static int bcm63xx_usbh_phy_init(struct phy *phy)
242 {
243 struct bcm63xx_usbh_phy *usbh = phy_get_drvdata(phy);
244 int ret;
245
246 ret = clk_prepare_enable(usbh->usbh_clk);
247 if (ret) {
248 dev_err(&phy->dev, "unable to enable usbh clock: %d\n", ret);
249 return ret;
250 }
251
252 ret = clk_prepare_enable(usbh->usb_ref_clk);
253 if (ret) {
254 dev_err(&phy->dev, "unable to enable usb_ref clock: %d\n", ret);
255 clk_disable_unprepare(usbh->usbh_clk);
256 return ret;
257 }
258
259 ret = reset_control_reset(usbh->reset);
260 if (ret) {
261 dev_err(&phy->dev, "unable to reset device: %d\n", ret);
262 clk_disable_unprepare(usbh->usb_ref_clk);
263 clk_disable_unprepare(usbh->usbh_clk);
264 return ret;
265 }
266
267 /* Configure to work in native CPU endian */
268 if (usbh_has_reg(usbh, USBH_SWAP_CONTROL)) {
269 u32 val = usbh_readl(usbh, USBH_SWAP_CONTROL);
270
271 val |= USBH_SC_EHCI_DATA_SWAP;
272 val &= ~USBH_SC_EHCI_ENDIAN_SWAP;
273
274 val |= USBH_SC_OHCI_DATA_SWAP;
275 val &= ~USBH_SC_OHCI_ENDIAN_SWAP;
276
277 if (usbh->device_mode && usbh->variant->swapctl_dev_set)
278 val |= usbh->variant->swapctl_dev_set;
279
280 usbh_writel(usbh, USBH_SWAP_CONTROL, val);
281 }
282
283 if (usbh_has_reg(usbh, USBH_SETUP)) {
284 u32 val = usbh_readl(usbh, USBH_SETUP);
285
286 val |= usbh->variant->setup_set;
287 val &= ~usbh->variant->setup_clr;
288
289 usbh_writel(usbh, USBH_SETUP, val);
290 }
291
292 if (usbh_has_reg(usbh, USBH_USB_SIM_CONTROL)) {
293 u32 val = usbh_readl(usbh, USBH_USB_SIM_CONTROL);
294
295 val |= usbh->variant->usc_set;
296
297 usbh_writel(usbh, USBH_USB_SIM_CONTROL, val);
298 }
299
300 if (usbh->variant->tpc_val &&
301 usbh_has_reg(usbh, USBH_TEST_PORT_CONTROL))
302 usbh_writel(usbh, USBH_TEST_PORT_CONTROL,
303 usbh->variant->tpc_val);
304
305 if (usbh->device_mode &&
306 usbh_has_reg(usbh, USBH_UTMI_CONTROL1) &&
307 usbh->variant->utmictl1_dev_set) {
308 u32 val = usbh_readl(usbh, USBH_UTMI_CONTROL1);
309
310 val |= usbh->variant->utmictl1_dev_set;
311
312 usbh_writel(usbh, USBH_UTMI_CONTROL1, val);
313 }
314
315 return 0;
316 }
317
bcm63xx_usbh_phy_power_on(struct phy * phy)318 static int bcm63xx_usbh_phy_power_on(struct phy *phy)
319 {
320 struct bcm63xx_usbh_phy *usbh = phy_get_drvdata(phy);
321
322 if (usbh_has_reg(usbh, USBH_PLL_CONTROL1)) {
323 u32 val = usbh_readl(usbh, USBH_PLL_CONTROL1);
324
325 val |= usbh->variant->power_pllc_set;
326 val &= ~usbh->variant->power_pllc_clr;
327
328 usbh_writel(usbh, USBH_PLL_CONTROL1, val);
329 }
330
331 return 0;
332 }
333
bcm63xx_usbh_phy_power_off(struct phy * phy)334 static int bcm63xx_usbh_phy_power_off(struct phy *phy)
335 {
336 struct bcm63xx_usbh_phy *usbh = phy_get_drvdata(phy);
337
338 if (usbh_has_reg(usbh, USBH_PLL_CONTROL1)) {
339 u32 val = usbh_readl(usbh, USBH_PLL_CONTROL1);
340
341 val &= ~usbh->variant->power_pllc_set;
342 val |= usbh->variant->power_pllc_clr;
343
344 usbh_writel(usbh, USBH_PLL_CONTROL1, val);
345 }
346
347 return 0;
348 }
349
bcm63xx_usbh_phy_exit(struct phy * phy)350 static int bcm63xx_usbh_phy_exit(struct phy *phy)
351 {
352 struct bcm63xx_usbh_phy *usbh = phy_get_drvdata(phy);
353
354 clk_disable_unprepare(usbh->usbh_clk);
355 clk_disable_unprepare(usbh->usb_ref_clk);
356
357 return 0;
358 }
359
360 static const struct phy_ops bcm63xx_usbh_phy_ops = {
361 .exit = bcm63xx_usbh_phy_exit,
362 .init = bcm63xx_usbh_phy_init,
363 .power_off = bcm63xx_usbh_phy_power_off,
364 .power_on = bcm63xx_usbh_phy_power_on,
365 .owner = THIS_MODULE,
366 };
367
bcm63xx_usbh_phy_xlate(struct device * dev,const struct of_phandle_args * args)368 static struct phy *bcm63xx_usbh_phy_xlate(struct device *dev,
369 const struct of_phandle_args *args)
370 {
371 struct bcm63xx_usbh_phy *usbh = dev_get_drvdata(dev);
372
373 usbh->device_mode = !!args->args[0];
374
375 return of_phy_simple_xlate(dev, args);
376 }
377
bcm63xx_usbh_phy_probe(struct platform_device * pdev)378 static int __init bcm63xx_usbh_phy_probe(struct platform_device *pdev)
379 {
380 struct device *dev = &pdev->dev;
381 struct bcm63xx_usbh_phy *usbh;
382 const struct bcm63xx_usbh_phy_variant *variant;
383 struct phy *phy;
384 struct phy_provider *phy_provider;
385
386 usbh = devm_kzalloc(dev, sizeof(*usbh), GFP_KERNEL);
387 if (!usbh)
388 return -ENOMEM;
389
390 variant = device_get_match_data(dev);
391 if (!variant)
392 return -EINVAL;
393 usbh->variant = variant;
394
395 usbh->base = devm_platform_ioremap_resource(pdev, 0);
396 if (IS_ERR(usbh->base))
397 return PTR_ERR(usbh->base);
398
399 usbh->reset = devm_reset_control_get_exclusive(dev, NULL);
400 if (IS_ERR(usbh->reset)) {
401 if (PTR_ERR(usbh->reset) != -EPROBE_DEFER)
402 dev_err(dev, "failed to get reset\n");
403 return PTR_ERR(usbh->reset);
404 }
405
406 usbh->usbh_clk = devm_clk_get_optional(dev, "usbh");
407 if (IS_ERR(usbh->usbh_clk))
408 return PTR_ERR(usbh->usbh_clk);
409
410 usbh->usb_ref_clk = devm_clk_get_optional(dev, "usb_ref");
411 if (IS_ERR(usbh->usb_ref_clk))
412 return PTR_ERR(usbh->usb_ref_clk);
413
414 phy = devm_phy_create(dev, NULL, &bcm63xx_usbh_phy_ops);
415 if (IS_ERR(phy)) {
416 dev_err(dev, "failed to create PHY\n");
417 return PTR_ERR(phy);
418 }
419
420 platform_set_drvdata(pdev, usbh);
421 phy_set_drvdata(phy, usbh);
422
423 phy_provider = devm_of_phy_provider_register(dev,
424 bcm63xx_usbh_phy_xlate);
425 if (IS_ERR(phy_provider)) {
426 dev_err(dev, "failed to register PHY provider\n");
427 return PTR_ERR(phy_provider);
428 }
429
430 dev_dbg(dev, "Registered BCM63xx USB PHY driver\n");
431
432 return 0;
433 }
434
435 static const struct of_device_id bcm63xx_usbh_phy_ids[] __initconst = {
436 { .compatible = "brcm,bcm6318-usbh-phy", .data = &usbh_bcm6318 },
437 { .compatible = "brcm,bcm6328-usbh-phy", .data = &usbh_bcm6328 },
438 { .compatible = "brcm,bcm6358-usbh-phy", .data = &usbh_bcm6358 },
439 { .compatible = "brcm,bcm6362-usbh-phy", .data = &usbh_bcm6368 },
440 { .compatible = "brcm,bcm6368-usbh-phy", .data = &usbh_bcm6368 },
441 { .compatible = "brcm,bcm63268-usbh-phy", .data = &usbh_bcm63268 },
442 { /* sentinel */ }
443 };
444 MODULE_DEVICE_TABLE(of, bcm63xx_usbh_phy_ids);
445
446 static struct platform_driver bcm63xx_usbh_phy_driver __refdata = {
447 .driver = {
448 .name = "bcm63xx-usbh-phy",
449 .of_match_table = bcm63xx_usbh_phy_ids,
450 },
451 .probe = bcm63xx_usbh_phy_probe,
452 };
453 module_platform_driver(bcm63xx_usbh_phy_driver);
454
455 MODULE_DESCRIPTION("BCM63xx USBH PHY driver");
456 MODULE_AUTHOR("Álvaro Fernández Rojas <noltari@gmail.com>");
457 MODULE_AUTHOR("Simon Arlott");
458 MODULE_LICENSE("GPL");
459