/linux/Documentation/hwmon/ |
H A D | tps23861.rst | 23 TPS23861 offers three modes of operation: Auto, Semi-Auto and Manual. 25 This driver only supports the Auto mode of operation providing monitoring
|
H A D | dme1737.rst | 279 zone[1-3]_auto_point1_temp_hyst RW Auto PWM temp point1 hysteresis. The 284 zone[1-3]_auto_point[1-3]_temp RW Auto PWM temp points. Auto_point1 is 335 pwm[1-3]_auto_pwm_min RW Auto PWM min pwm. Minimum PWM duty- 338 pwm[1-3]_auto_point1_pwm RW Auto PWM pwm point. Auto_point1 is the 340 pwm[1-3]_auto_point2_pwm RO Auto PWM pwm point. Auto_point2 is the
|
H A D | vt1211.rst | 194 PWM Auto Point PWM Output Duty-Cycle 203 Temp Auto Point Thermal Threshold
|
/linux/Documentation/userspace-api/media/v4l/ |
H A D | metafmt-intel-ipu3.rst | 21 The statistics collected are AWB (Auto-white balance) RGBS (Red, Green, Blue and 22 Saturation measure) cells, AWB filter response, AF (Auto-focus) filter response, 23 and AE (Auto-exposure) histogram.
|
H A D | metafmt-rkisp1.rst | 79 The statistics collected are Exposure, AWB (Auto-white balance), Histogram and 80 AF (Auto-focus). See :c:type:`rkisp1_stat_buffer` for details of the statistics.
|
/linux/arch/arc/include/asm/ |
H A D | entry-arcv2.h | 54 ; 3. Auto save: (mandatory) Push PC and STAT32 on stack 56 ; 4a. Auto save: (optional) r0-r11, blink, LPE,LPS,LPC, JLI,LDI,EI 59 ; 4b. If Auto-save (optional) not enabled in hw, manually save them 158 ; Auto stack switch works
|
/linux/drivers/firmware/microchip/ |
H A D | Kconfig | 10 Auto Upgrade feature of the system controller.
|
/linux/drivers/net/wireless/broadcom/b43legacy/ |
H A D | Kconfig | 23 # Auto-select SSB PCI-HOST support, if possible 31 # Auto-select SSB PCICORE driver, if possible
|
/linux/Documentation/networking/devlink/ |
H A D | devlink-health.rst | 50 * Auto recovery attempt is being done. Depends on: 52 - Auto-recovery configuration
|
/linux/Documentation/tools/rtla/ |
H A D | rtla-timerlat-hist.rst | 40 *1ms* period is also passed to the *timerlat* tracer. Auto-analysis is disabled
|
/linux/arch/arm64/boot/dts/exynos/ |
H A D | exynos850-pinctrl.dtsi | 225 /* USI_CMGP0: UART function (4 pins, Auto Flow Control) */ 232 /* USI_CMGP0: UART function (2 pins, Non-Auto Flow Control) */ 255 /* USI_CMGP1: UART function (4 pins, Auto Flow Control) */ 262 /* USI_CMGP1: UART function (2 pins, Non-Auto Flow Control) */
|
/linux/Documentation/sound/cards/ |
H A D | hdspm.rst | 164 Within the Auto-sync-Mode the preferred Sync Source can be 203 * Safe Mode oder Auto Input 325 Used input for Auto-Input.
|
/linux/Documentation/sound/hd-audio/ |
H A D | controls.rst | 18 Auto-Mute Mode 104 Auto-Mute Mode
|
/linux/drivers/net/wireless/broadcom/b43/ |
H A D | Kconfig | 61 # Auto-select SSB PCI-HOST support, if possible 69 # Auto-select SSB PCICORE driver, if possible
|
/linux/Documentation/gpu/ |
H A D | kms-properties.csv | 59 armada,CRTC,"""CSC_YUV""",ENUM,"{ ""Auto"" , ""CCIR601"", ""CCIR709"" }",CRTC,TBD 60 ,,"""CSC_RGB""",ENUM,"{ ""Auto"", ""Computer system"", ""Studio"" }",CRTC,TBD
|
/linux/Documentation/networking/device_drivers/ethernet/netronome/ |
H A D | nfp.rst | 235 Agilio SmartNICs support FEC mode configuration, e.g. Auto, Firecode Base-R, 247 (see the `Auto-negotiation`_ section). An example of how to set the FEC mode 252 Auto-negotiation
|
/linux/Documentation/networking/ |
H A D | driver.rst | 28 Auto-close
|
/linux/Documentation/networking/device_drivers/ethernet/ti/ |
H A D | tlan.rst | 90 do "insmod tlan.o speed=100" the driver will do Auto-Neg.
|
/linux/Documentation/networking/device_drivers/ethernet/aquantia/ |
H A D | atlantic.rst | 102 Auto-negotiation: on 420 0xFFFF Auto throttling mode. Driver will choose the best RX and TX
|
/linux/Documentation/core-api/ |
H A D | printk-index.rst | 126 pr_info("Auto-serialization disabled\n");
|
/linux/Documentation/dev-tools/ |
H A D | autofdo.rst | 8 the Clang compiler. AutoFDO (Auto-Feedback-Directed Optimization)
|
/linux/ |
H A D | .clang-format | 729 ObjCBinPackProtocolList: Auto
|
/linux/Documentation/ABI/testing/ |
H A D | sysfs-driver-toshiba_acpi | 88 * 2 -> Auto (0x21)
|
/linux/arch/arm/boot/dts/nxp/imx/ |
H A D | imx6sx-sabreauto.dts | 10 model = "Freescale i.MX6 SoloX Sabre Auto Board";
|
/linux/drivers/pcmcia/ |
H A D | Kconfig | 106 bool "Auto-tune EnE bridges for CB cards" if EXPERT
|