| /freebsd/sys/contrib/device-tree/Bindings/input/ |
| H A D | ti,drv260x.txt | 16 - library-sel - These are ROM based waveforms pre-programmed into the IC.
19 DRV260X_LIB_EMPTY - Do not use a pre-programmed library
20 DRV260X_ERM_LIB_A - Pre-programmed Library
21 DRV260X_ERM_LIB_B - Pre-programmed Library
22 DRV260X_ERM_LIB_C - Pre-programmed Library
23 DRV260X_ERM_LIB_D - Pre-programmed Library
24 DRV260X_ERM_LIB_E - Pre-programmed Library
25 DRV260X_ERM_LIB_F - Pre-programmed Library
26 DRV260X_LIB_LRA - Pre-programmed LRA Library
|
| /freebsd/contrib/kyua/utils/signals/ |
| H A D | programmer.cpp | 54 bool programmed; member
64 programmed(false) in impl()
96 _pimpl->programmed = true; in programmer()
106 if (_pimpl->programmed) { in ~programmer()
127 PRE(_pimpl->programmed); in unprogram()
131 _pimpl->programmed = false; in unprogram()
|
| H A D | timer.cpp | 392 bool programmed; member
404 when(when_), programmed(true), fired(false) in impl()
444 if (_pimpl->programmed) { in ~timer()
523 if (!_pimpl->programmed) { in unprogram()
535 _pimpl->programmed = false; in unprogram()
|
| /freebsd/sys/contrib/device-tree/Bindings/i2c/ |
| H A D | i2c-mux-pinctrl.txt | 48 state will be programmed into hardware.
51 on a child bus, the idle pinctrl state will be programmed into hardware.
54 left programmed into hardware whenever no access is being made of a device on
|
| H A D | i2c-mux-gpio.txt | 44 left programmed into hardware whenever no access is being made to a
|
| /freebsd/sys/contrib/device-tree/Bindings/clock/ |
| H A D | silabs,si5341.txt | 21 chip at boot, in case you have a (pre-)programmed device. If the PLL is not
28 still be programmed into the chip and the driver will leave them "as is".
56 If these are not specified, and the PLL is not yet programmed when the driver
119 silabs,reprogram; /* Chips are not programmed, always reset */
|
| /freebsd/sys/contrib/device-tree/Bindings/clock/ti/ |
| H A D | mux.txt | 9 as they are programmed into the register. E.g:
20 Some clock controller IPs do not allow a value of zero to be programmed
|
| /freebsd/sys/contrib/device-tree/Bindings/fpga/ |
| H A D | fpga-region.txt | 32 * The entire FPGA is programmed.
59 * FPGA Bridges should be disabled while the FPGA is being programmed to
138 Region, the FPGA already has been programmed. A DTO that targets an FPGA Region
177 it indicates that the FPGA has already been programmed with this image.
192 programmed.
195 programmed.
197 FPGA to go to operating mode after the region has been programmed.
298 In this case, the FPGA will have one or more PRR's that may be programmed
|
| /freebsd/sys/contrib/device-tree/Bindings/rtc/ |
| H A D | xlnx-rtc.txt | 15 be programmed directly to calibration register
|
| /freebsd/sys/contrib/device-tree/Bindings/timer/ |
| H A D | snps,arc-timer.txt | 3 - Can be optionally programmed to interrupt on Limit
|
| H A D | jcore,pit.txt | 13 assignment to be programmed by software, but this property is
|
| H A D | nvidia,tegra210-timer.txt | 6 (TMR10-TMR13). Each TMR can be programmed to generate one-shot, periodic,
|
| /freebsd/sys/contrib/device-tree/Bindings/sound/ |
| H A D | fsl,ssi.txt | 4 be programmed in AC97, I2S, left-justified, or right-justified modes.
47 If specified, the SSI is to be programmed in asynchronous
|
| /freebsd/sys/contrib/device-tree/Bindings/pinctrl/ |
| H A D | ti,iodelay.txt | 4 for each pin. For most part the IO delay values are programmed by the bootloader,
|
| /freebsd/sys/contrib/device-tree/Bindings/power/supply/ |
| H A D | ltc2941.txt | 17 This determines the range and accuracy of the gauge. The value is programmed
|
| /freebsd/sys/contrib/device-tree/Bindings/dma/ |
| H A D | snps,dw-axi-dmac.txt | 13 dma-channels. Priority value must be programmed within [0:dma-channels-1]
|
| /freebsd/sys/contrib/device-tree/Bindings/gpio/ |
| H A D | sgpio-aspeed.txt | 5 featured Serial GPIOs. Each of the Serial GPIO pins can be programmed to
|
| /freebsd/sys/contrib/device-tree/Bindings/display/ |
| H A D | arm,hdlcd.txt | 12 interrupt controller when any of the interrupt sources programmed in
|
| /freebsd/sys/contrib/device-tree/src/arm/ti/omap/ |
| H A D | am335x-osd335x-common.dtsi | 24 * The EFUSE_SMA register is not programmed for any of the AM335x wafers
|
| /freebsd/sys/contrib/device-tree/Bindings/mtd/ |
| H A D | fsl-upm-nand.txt | 1 Freescale Localbus UPM programmed to work with NAND flash
|
| /freebsd/sys/contrib/device-tree/Bindings/mfd/ |
| H A D | max77620.txt | 34 and power-down delays (sequencing). GPIO1, GPIO2, and GPIO3 can be programmed
36 with internal regulators. 32KHz clock can be programmed to be part of a
|
| /freebsd/sys/contrib/device-tree/Bindings/mmc/ |
| H A D | nvidia,tegra20-sdhci.txt | 89 - The property values are drive codes which are programmed into the
100 - The values are programmed to the Vendor Clock Control Register.
|
| /freebsd/sys/contrib/device-tree/Bindings/watchdog/ |
| H A D | aspeed-wdt.txt | 16 Reset behavior - Whenever a timeout occurs the watchdog can be programmed
|
| /freebsd/sys/contrib/device-tree/Bindings/thermal/ |
| H A D | qoriq-thermal.txt | 13 - fsl,tmu-range : The values to be programmed into TTRnCR, as specified by
|
| /freebsd/sys/contrib/device-tree/Bindings/net/ |
| H A D | socionext-netsec.txt | 34 be set to the empty string if the PHY configuration is programmed by
|