xref: /linux/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp15-som.dtsi (revision 06d07429858317ded2db7986113a9e0129cd599b) 
1// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
2/*
3 * Copyright (C) 2022-2023 Steffen Trumtrar <kernel@pengutronix.de>
4 * Copyright (C) Phytec GmbH 2019-2020 - All Rights Reserved
5 * Author: Dom VOVARD <dom.vovard@linrt.com>.
6 */
7
8#include <dt-bindings/gpio/gpio.h>
9#include <dt-bindings/input/input.h>
10#include <dt-bindings/interrupt-controller/arm-gic.h>
11#include <dt-bindings/interrupt-controller/irq.h>
12#include <dt-bindings/leds/common.h>
13#include <dt-bindings/leds/leds-pca9532.h>
14#include <dt-bindings/mfd/st,stpmic1.h>
15#include <dt-bindings/net/ti-dp83867.h>
16#include "stm32mp15-pinctrl.dtsi"
17
18/ {
19	model = "PHYTEC phyCORE-STM32MP15 SOM";
20	compatible = "phytec,phycore-stm32mp157c-som", "st,stm32mp157";
21
22	aliases {
23		ethernet0 = &ethernet0;
24		rtc0 = &i2c4_rtc;
25		rtc1 = &rtc;
26	};
27
28	chosen {
29		stdout-path = "serial0:115200n8";
30	};
31
32	gpio-keys {
33		compatible = "gpio-keys";
34
35		key-home {
36			label = "Home";
37			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
38			linux,code = <KEY_HOME>;
39		};
40
41		key-enter {
42			label = "Enter";
43			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
44			linux,code = <KEY_ENTER>;
45		};
46	};
47
48	reserved-memory {
49		#address-cells = <1>;
50		#size-cells = <1>;
51		ranges;
52
53		retram: retram@38000000 {
54			compatible = "shared-dma-pool";
55			reg = <0x38000000 0x10000>;
56			no-map;
57		};
58
59		mcuram: mcuram@30000000 {
60			compatible = "shared-dma-pool";
61			reg = <0x30000000 0x40000>;
62			no-map;
63		};
64
65		mcuram2: mcuram2@10000000 {
66			compatible = "shared-dma-pool";
67			reg = <0x10000000 0x40000>;
68			no-map;
69		};
70
71		vdev0vring0: vdev0vring0@10040000 {
72			compatible = "shared-dma-pool";
73			reg = <0x10040000 0x1000>;
74			no-map;
75		};
76
77		vdev0vring1: vdev0vring1@10041000 {
78			compatible = "shared-dma-pool";
79			reg = <0x10041000 0x1000>;
80			no-map;
81		};
82
83		vdev0buffer: vdev0buffer@10042000 {
84			compatible = "shared-dma-pool";
85			reg = <0x10042000 0x4000>;
86			no-map;
87		};
88	};
89
90	sound {
91		compatible = "audio-graph-card";
92		label = "STM32MP1-PHYCORE";
93		routing =
94			"Playback", "MCLK", /* Set a route between "MCLK" and "playback" widgets */
95			"Capture", "MCLK";
96		dais = <&sai2b_port>,
97		       <&sai2a_port>;
98	};
99
100	regulator_vin: regulator {
101		compatible = "regulator-fixed";
102		regulator-name = "vin";
103		regulator-min-microvolt = <5000000>;
104		regulator-max-microvolt = <5000000>;
105		regulator-always-on;
106	};
107};
108
109&ethernet0 {
110	pinctrl-0 = <&ethernet0_rgmii_pins_d>;
111	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_d>;
112	pinctrl-names = "default", "sleep";
113	phy-mode = "rgmii-id";
114	max-speed = <1000>;
115	phy-handle = <&phy0>;
116	st,eth-clk-sel;
117	status = "okay";
118
119	mdio {
120		#address-cells = <1>;
121		#size-cells = <0>;
122		compatible = "snps,dwmac-mdio";
123
124		phy0: ethernet-phy@1 {
125			compatible = "ethernet-phy-ieee802.3-c22";
126			reg = <1>;
127			interrupt-parent = <&gpiog>;
128			interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
129			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
130			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
131			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
132			ti,min-output-impedance;
133			enet-phy-lane-no-swap;
134			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
135		};
136	};
137};
138
139&i2c1 {
140	pinctrl-names = "default", "sleep";
141	pinctrl-0 = <&i2c1_pins_b>;
142	pinctrl-1 = <&i2c1_sleep_pins_b>;
143	i2c-scl-rising-time-ns = <100>;
144	i2c-scl-falling-time-ns = <7>;
145	status = "okay";
146
147	codec@18 {
148		compatible = "ti,tlv320aic3007";
149		reg = <0x18>;
150		#sound-dai-cells = <0>;
151
152		ai3x-micbias-vg = <2>;
153
154		AVDD-supply = <&v3v3>;
155		IOVDD-supply = <&v3v3>;
156		DRVDD-supply = <&v3v3>;
157		DVDD-supply = <&v1v8_audio>;
158
159		clocks = <&sai2b>;
160
161		port {
162			#address-cells = <1>;
163			#size-cells = <0>;
164
165			tlv320_tx_endpoint: endpoint@0 {
166				reg = <0>;
167				remote-endpoint = <&sai2b_endpoint>;
168				frame-master;
169				bitclock-master;
170			};
171
172			tlv320_rx_endpoint: endpoint@1 {
173				reg = <1>;
174				remote-endpoint = <&sai2a_endpoint>;
175				frame-master;
176				bitclock-master;
177			};
178		};
179	};
180
181	touch@44 {
182		compatible = "st,stmpe811";
183		reg = <0x44>;
184		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
185		interrupt-parent = <&gpioi>;
186		vio-supply = <&v3v3>;
187		vcc-supply = <&v3v3>;
188
189		touchscreen {
190			compatible = "st,stmpe-ts";
191			st,sample-time = <4>;
192			st,mod-12b = <1>;
193			st,ref-sel = <0>;
194			st,adc-freq = <1>;
195			st,ave-ctrl = <1>;
196			st,touch-det-delay = <2>;
197			st,settling = <2>;
198			st,fraction-z = <7>;
199			st,i-drive = <1>;
200		};
201	};
202
203	leds@62 {
204		compatible = "nxp,pca9533";
205		reg = <0x62>;
206
207		led-0 {
208			color = <LED_COLOR_ID_RED>;
209			function = LED_FUNCTION_POWER;
210			type = <PCA9532_TYPE_LED>;
211		};
212
213		led-1 {
214			color = <LED_COLOR_ID_GREEN>;
215			function = LED_FUNCTION_POWER;
216			type = <PCA9532_TYPE_LED>;
217		};
218
219		led-2 {
220			color = <LED_COLOR_ID_BLUE>;
221			function = LED_FUNCTION_HEARTBEAT;
222			type = <PCA9532_TYPE_LED>;
223			linux,default-trigger = "heartbeat";
224		};
225	};
226};
227
228&i2c4 {
229	pinctrl-names = "default", "sleep";
230	pinctrl-0 = <&i2c4_pins_a>;
231	pinctrl-1 = <&i2c4_sleep_pins_a>;
232	i2c-scl-rising-time-ns = <185>;
233	i2c-scl-falling-time-ns = <20>;
234	status = "okay";
235
236	pmic@33 {
237		compatible = "st,stpmic1";
238		reg = <0x33>;
239		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
240		interrupt-controller;
241		#interrupt-cells = <2>;
242
243		regulators {
244			compatible = "st,stpmic1-regulators";
245			buck1-supply = <&regulator_vin>;
246			buck2-supply = <&regulator_vin>;
247			buck3-supply = <&regulator_vin>;
248			buck4-supply = <&regulator_vin>;
249			ldo1-supply = <&v3v3>;
250			ldo2-supply = <&v3v3>;
251			ldo3-supply = <&vdd_ddr>;
252			ldo4-supply = <&regulator_vin>;
253			ldo5-supply = <&v3v3>;
254			ldo6-supply = <&v3v3>;
255			boost-supply = <&regulator_vin>;
256			pwr_sw1-supply = <&bst_out>;
257			pwr_sw2-supply = <&bst_out>;
258
259			vddcore: buck1 {
260				regulator-name = "vddcore";
261				regulator-min-microvolt = <1200000>;
262				regulator-max-microvolt = <1350000>;
263				regulator-always-on;
264				regulator-initial-mode = <0>;
265			};
266
267			vdd_ddr: buck2 {
268				regulator-name = "vdd_ddr";
269				regulator-min-microvolt = <1350000>;
270				regulator-max-microvolt = <1350000>;
271				regulator-always-on;
272				regulator-initial-mode = <0>;
273			};
274
275			vdd: buck3 {
276				regulator-name = "vdd";
277				regulator-min-microvolt = <3300000>;
278				regulator-max-microvolt = <3300000>;
279				regulator-always-on;
280				st,mask-reset;
281				regulator-initial-mode = <0>;
282			};
283
284			v3v3: buck4 {
285				regulator-name = "v3v3";
286				regulator-min-microvolt = <3300000>;
287				regulator-max-microvolt = <3300000>;
288				regulator-always-on;
289				regulator-initial-mode = <0>;
290			};
291
292			v1v8_audio: ldo1 {
293				regulator-name = "v1v8_audio";
294				regulator-min-microvolt = <1800000>;
295				regulator-max-microvolt = <1800000>;
296				regulator-always-on;
297				interrupts = <IT_CURLIM_LDO1 0>;
298
299			};
300
301			vdd_eth_2v5: ldo2 {
302				regulator-name = "dd_eth_2v5";
303				regulator-min-microvolt = <2500000>;
304				regulator-max-microvolt = <2500000>;
305				regulator-always-on;
306				interrupts = <IT_CURLIM_LDO2 0>;
307
308			};
309
310			vtt_ddr: ldo3 {
311				regulator-name = "vtt_ddr";
312				regulator-min-microvolt = <500000>;
313				regulator-max-microvolt = <750000>;
314				regulator-always-on;
315				regulator-over-current-protection;
316			};
317
318			vdd_usb: ldo4 {
319				regulator-name = "vdd_usb";
320				interrupts = <IT_CURLIM_LDO4 0>;
321			};
322
323			vdda: ldo5 {
324				regulator-name = "vdda";
325				regulator-min-microvolt = <2900000>;
326				regulator-max-microvolt = <2900000>;
327				interrupts = <IT_CURLIM_LDO5 0>;
328				regulator-boot-on;
329			};
330
331			vdd_eth_1v0: ldo6 {
332				regulator-name = "vdd_eth_1v0";
333				regulator-min-microvolt = <1000000>;
334				regulator-max-microvolt = <1000000>;
335				regulator-always-on;
336				interrupts = <IT_CURLIM_LDO6 0>;
337
338			};
339
340			vref_ddr: vref_ddr {
341				regulator-name = "vref_ddr";
342				regulator-always-on;
343			};
344
345			bst_out: boost {
346				regulator-name = "bst_out";
347				interrupts = <IT_OCP_BOOST 0>;
348			};
349
350			vbus_otg: pwr_sw1 {
351				regulator-name = "vbus_otg";
352				interrupts = <IT_OCP_OTG 0>;
353				regulator-active-discharge = <1>;
354			};
355
356			vbus_sw: pwr_sw2 {
357				regulator-name = "vbus_sw";
358				interrupts = <IT_OCP_SWOUT 0>;
359				regulator-active-discharge = <1>;
360			};
361		};
362
363		onkey {
364			compatible = "st,stpmic1-onkey";
365			interrupts = <IT_PONKEY_F 0>,
366				     <IT_PONKEY_R 0>;
367			interrupt-names = "onkey-falling",
368					  "onkey-rising";
369			power-off-time-sec = <10>;
370		};
371
372		watchdog {
373			compatible = "st,stpmic1-wdt";
374		};
375	};
376
377	i2c4_eeprom: eeprom@50 {
378		compatible = "microchip,24c32",
379			     "atmel,24c32";
380		reg = <0x50>;
381	};
382
383	i2c4_rtc: rtc@52 {
384		compatible = "microcrystal,rv3028";
385		reg = <0x52>;
386	};
387};
388
389&ipcc {
390	status = "okay";
391};
392
393&iwdg2 {
394	timeout-sec = <32>;
395	status = "okay";
396};
397
398&m_can2 {
399	pinctrl-names = "default", "sleep";
400	pinctrl-0 = <&m_can2_pins_a>;
401	pinctrl-1 = <&m_can2_sleep_pins_a>;
402	status = "okay";
403};
404
405&m4_rproc {
406	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
407			<&vdev0vring1>, <&vdev0buffer>;
408	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
409	mbox-names = "vq0", "vq1", "shutdown", "detach";
410	interrupt-parent = <&exti>;
411	interrupts = <68 1>;
412	status = "okay";
413};
414
415&pwr_regulators {
416	vdd-supply = <&vdd>;
417	vdd_3v3_usbfs-supply = <&vdd_usb>;
418};
419
420&qspi {
421	pinctrl-names = "default", "sleep";
422	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
423	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
424	status = "okay";
425
426	flash0: flash@0 {
427		compatible = "winbond,w25q128", "jedec,spi-nor";
428		reg = <0>;
429		spi-rx-bus-width = <4>;
430		spi-max-frequency = <50000000>;
431		m25p,fast-read;
432		#address-cells = <1>;
433		#size-cells = <1>;
434	};
435};
436
437&rng1 {
438	status = "okay";
439};
440
441&rtc {
442	status = "okay";
443};
444
445&sai2 {
446	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
447	clock-names = "pclk", "x8k", "x11k";
448	pinctrl-names = "default", "sleep";
449	pinctrl-0 = <&sai2a_pins_b>, <&sai2b_pins_d>;
450	pinctrl-1 = <&sai2a_sleep_pins_b>, <&sai2b_sleep_pins_d>;
451	status = "okay";
452};
453
454&sai2a {
455	dma-names = "rx";
456	st,sync = <&sai2b 2>;
457	clocks = <&rcc SAI2_K>, <&sai2b>;
458	clock-names = "sai_ck", "MCLK";
459	#clock-cells = <0>;
460
461	sai2a_port: port {
462		sai2a_endpoint: endpoint {
463			remote-endpoint = <&tlv320_rx_endpoint>;
464			mclk-fs = <256>;
465			dai-tdm-slot-num = <2>;
466			dai-tdm-slot-width = <16>;
467		};
468	};
469};
470
471&sai2b {
472	dma-names = "tx";
473	#clock-cells = <0>;
474
475	sai2b_port: port {
476		sai2b_endpoint: endpoint {
477			remote-endpoint = <&tlv320_tx_endpoint>;
478			mclk-fs = <256>;
479			dai-tdm-slot-num = <2>;
480			dai-tdm-slot-width = <16>;
481		};
482	};
483};
484
485&sdmmc1 {
486	pinctrl-names = "default", "opendrain", "sleep";
487	pinctrl-0 = <&sdmmc1_b4_pins_b>;
488	pinctrl-1 = <&sdmmc1_b4_od_pins_b>;
489	pinctrl-2 = <&sdmmc1_b4_sleep_pins_b>;
490	cd-gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
491	disable-wp;
492	st,neg-edge;
493	bus-width = <4>;
494	vmmc-supply = <&v3v3>;
495	status = "okay";
496};
497
498&sdmmc2 {
499	pinctrl-names = "default", "opendrain", "sleep";
500	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_e>;
501	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_e>;
502	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_e>;
503	non-removable;
504	no-sd;
505	no-sdio;
506	st,neg-edge;
507	bus-width = <8>;
508	vmmc-supply = <&v3v3>;
509	vqmmc-supply = <&v3v3>;
510	mmc-ddr-3_3v;
511};
512
513&spi1 {
514	pinctrl-names = "default", "sleep";
515	pinctrl-0 = <&spi1_pins_a>;
516	pinctrl-1 = <&spi1_sleep_pins_a>;
517	cs-gpios = <&gpioz 3 0>;
518	status = "okay";
519};
520
521&uart4 {
522	pinctrl-names = "default", "sleep", "idle";
523	pinctrl-0 = <&uart4_pins_a>;
524	pinctrl-1 = <&uart4_sleep_pins_a>;
525	pinctrl-2 = <&uart4_idle_pins_a>;
526	pinctrl-3 = <&uart4_pins_a>;
527	/delete-property/dmas;
528	/delete-property/dma-names;
529	status = "okay";
530};
531
532&usart1 {
533	pinctrl-names = "default", "sleep", "idle";
534	pinctrl-0 = <&usart1_pins_b &usart1_pins_a>;
535	pinctrl-1 = <&usart1_sleep_pins_b &usart1_sleep_pins_a>;
536	pinctrl-2 = <&usart1_idle_pins_b &usart1_idle_pins_a>;
537	uart-has-rtscts;
538	status = "okay";
539};
540
541&usart3 {
542	pinctrl-names = "default", "sleep", "idle";
543	pinctrl-0 = <&usart3_pins_a>;
544	pinctrl-1 = <&usart3_sleep_pins_a>;
545	pinctrl-2 = <&usart3_idle_pins_a>;
546	status = "okay";
547};
548
549&usbh_ehci {
550	status = "okay";
551};
552
553&usbh_ohci {
554	status = "okay";
555};
556
557&usbotg_hs {
558	phys = <&usbphyc_port1 0>;
559	phy-names = "usb2-phy";
560	status = "okay";
561};
562
563&usbphyc {
564	status = "okay";
565};
566
567&usbphyc_port0 {
568	phy-supply = <&vdd_usb>;
569};
570
571&usbphyc_port1 {
572	phy-supply = <&vdd_usb>;
573};
574