1// SPDX-License-Identifier: GPL-2.0-or-later 2/* 3 * Copyright 2012 Sascha Hauer, Uwe Kleine-König, Steffen Trumtrar 4 * and Markus Pargmann, Pengutronix 5 */ 6 7/dts-v1/; 8#include "imx27.dtsi" 9 10/ { 11 model = "Phytec pca100"; 12 compatible = "phytec,imx27-pca100", "fsl,imx27"; 13 14 memory@a0000000 { 15 device_type = "memory"; 16 reg = <0xa0000000 0x08000000>; /* 128MB */ 17 }; 18 19 usbotgphy: usbotgphy { 20 compatible = "usb-nop-xceiv"; 21 pinctrl-names = "default"; 22 pinctrl-0 = <&pinctrl_usbotgphy>; 23 reset-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>; 24 #phy-cells = <0>; 25 }; 26 27 usbh2phy: usbh2phy { 28 compatible = "usb-nop-xceiv"; 29 pinctrl-names = "default"; 30 pinctrl-0 = <&pinctrl_usbh2phy>; 31 reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; 32 #phy-cells = <0>; 33 }; 34}; 35 36&cspi1 { 37 cs-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>, 38 <&gpio4 27 GPIO_ACTIVE_LOW>; 39 status = "okay"; 40}; 41 42&fec { 43 pinctrl-names = "default"; 44 pinctrl-0 = <&pinctrl_fec1>; 45 status = "okay"; 46}; 47 48&i2c2 { 49 pinctrl-names = "default"; 50 pinctrl-0 = <&pinctrl_i2c2>; 51 status = "okay"; 52 53 eeprom@52 { 54 compatible = "atmel,24c32"; 55 pagesize = <32>; 56 reg = <0x52>; 57 }; 58}; 59 60&iomuxc { 61 imx27-phycard-s-som { 62 pinctrl_fec1: fec1grp { 63 fsl,pins = < 64 MX27_PAD_SD3_CMD__FEC_TXD0 0x0 65 MX27_PAD_SD3_CLK__FEC_TXD1 0x0 66 MX27_PAD_ATA_DATA0__FEC_TXD2 0x0 67 MX27_PAD_ATA_DATA1__FEC_TXD3 0x0 68 MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0 69 MX27_PAD_ATA_DATA3__FEC_RXD1 0x0 70 MX27_PAD_ATA_DATA4__FEC_RXD2 0x0 71 MX27_PAD_ATA_DATA5__FEC_RXD3 0x0 72 MX27_PAD_ATA_DATA6__FEC_MDIO 0x0 73 MX27_PAD_ATA_DATA7__FEC_MDC 0x0 74 MX27_PAD_ATA_DATA8__FEC_CRS 0x0 75 MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0 76 MX27_PAD_ATA_DATA10__FEC_RXD0 0x0 77 MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0 78 MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0 79 MX27_PAD_ATA_DATA13__FEC_COL 0x0 80 MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0 81 MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0 82 >; 83 }; 84 85 pinctrl_i2c2: i2c2grp { 86 fsl,pins = < 87 MX27_PAD_I2C2_SDA__I2C2_SDA 0x0 88 MX27_PAD_I2C2_SCL__I2C2_SCL 0x0 89 >; 90 }; 91 92 pinctrl_nfc: nfcgrp { 93 fsl,pins = < 94 MX27_PAD_NFRB__NFRB 0x0 95 MX27_PAD_NFCLE__NFCLE 0x0 96 MX27_PAD_NFWP_B__NFWP_B 0x0 97 MX27_PAD_NFCE_B__NFCE_B 0x0 98 MX27_PAD_NFALE__NFALE 0x0 99 MX27_PAD_NFRE_B__NFRE_B 0x0 100 MX27_PAD_NFWE_B__NFWE_B 0x0 101 >; 102 }; 103 104 pinctrl_usbotgphy: usbotgphygrp { 105 fsl,pins = < 106 MX27_PAD_USBH1_RCV__GPIO2_25 0x1 /* reset gpio */ 107 >; 108 }; 109 110 pinctrl_usbotg: usbotggrp { 111 fsl,pins = < 112 MX27_PAD_USBOTG_CLK__USBOTG_CLK 0x0 113 MX27_PAD_USBOTG_DIR__USBOTG_DIR 0x0 114 MX27_PAD_USBOTG_NXT__USBOTG_NXT 0x0 115 MX27_PAD_USBOTG_STP__USBOTG_STP 0x0 116 MX27_PAD_USBOTG_DATA0__USBOTG_DATA0 0x0 117 MX27_PAD_USBOTG_DATA1__USBOTG_DATA1 0x0 118 MX27_PAD_USBOTG_DATA2__USBOTG_DATA2 0x0 119 MX27_PAD_USBOTG_DATA3__USBOTG_DATA3 0x0 120 MX27_PAD_USBOTG_DATA4__USBOTG_DATA4 0x0 121 MX27_PAD_USBOTG_DATA5__USBOTG_DATA5 0x0 122 MX27_PAD_USBOTG_DATA6__USBOTG_DATA6 0x0 123 MX27_PAD_USBOTG_DATA7__USBOTG_DATA7 0x0 124 >; 125 }; 126 127 pinctrl_usbh2phy: usbh2phygrp { 128 fsl,pins = < 129 MX27_PAD_USBH1_SUSP__GPIO2_22 0x0 /* reset gpio */ 130 >; 131 }; 132 133 pinctrl_usbh2: usbh2grp { 134 fsl,pins = < 135 MX27_PAD_USBH2_CLK__USBH2_CLK 0x0 136 MX27_PAD_USBH2_DIR__USBH2_DIR 0x0 137 MX27_PAD_USBH2_NXT__USBH2_NXT 0x0 138 MX27_PAD_USBH2_STP__USBH2_STP 0x0 139 MX27_PAD_CSPI2_SCLK__USBH2_DATA0 0x0 140 MX27_PAD_CSPI2_MOSI__USBH2_DATA1 0x0 141 MX27_PAD_CSPI2_MISO__USBH2_DATA2 0x0 142 MX27_PAD_CSPI2_SS1__USBH2_DATA3 0x0 143 MX27_PAD_CSPI2_SS2__USBH2_DATA4 0x0 144 MX27_PAD_CSPI1_SS2__USBH2_DATA5 0x0 145 MX27_PAD_CSPI2_SS0__USBH2_DATA6 0x0 146 MX27_PAD_USBH2_DATA7__USBH2_DATA7 0x0 147 >; 148 }; 149 }; 150}; 151 152&nfc { 153 pinctrl-names = "default"; 154 pinctrl-0 = <&pinctrl_nfc>; 155 nand-bus-width = <8>; 156 nand-ecc-mode = "hw"; 157 nand-on-flash-bbt; 158 status = "okay"; 159}; 160 161&usbotg { 162 pinctrl-names = "default"; 163 pinctrl-0 = <&pinctrl_usbotg>; 164 phy_type = "ulpi"; 165 phys = <&usbotgphy>; 166 status = "okay"; 167}; 168 169&usbh2 { 170 pinctrl-names = "default"; 171 pinctrl-0 = <&pinctrl_usbh2>; 172 phy_type = "ulpi"; 173 phys = <&usbh2phy>; 174 status = "okay"; 175}; 176